Bunn 270380000H Coffeemaker User Manual
Contents
1. Models with electronic control assemblies Place the tank heater switch at the top of the control assembly in the OFF position Models with electro mechanical thermostats Rotate the control thermostat knob fully counterclockwise to the OFF position Feed the cord through the strain relief and connect it to the terminal block 5 Connect the brewer to the power source and verify the voltage at the terminal block before proceeding Re place the front panel 6 If plumbing is to be hooked up later be sure the brewer is disconnected from the power source If plumbing has been hooked up the brewer is ready for Initial Set Up PLUMBING REQUIREMENTS This brewer must be connected to a cold water system with operating pressure between 20 and 90 psi 138 and 620 kPa from a or larger supply line A shut off valve should be installed in the line before the brewer Install a regulator in the line when pressure is greater than 90 psi 620 kPa to reduce it to 50 psi 138 kPa The water inlet fitting is flare NOTE Bunn O Matic recommends copper tubing for installations of less than 25 feet and for more than 25 feet from the water supply line A tight coil of copper tubing in the water line will facilitate moving the brewer to clean the counter top Bunn O Matic does not recommend the use of a saddle valve to install the brewer The size and shape of the hole made in the supply line by this type of device may restrict2. SINGLE es Serial SNGO005000 Up INSTALLATION amp OPERATING GUIDE BUNN O MATIC CORPORATION POST OFFICE BOX 3227 SPRINGFIELD ILLINOIS 62708 3227 PHONE 217 529 6601 FAX 217 529 6644 To ensure you have the latest revision of the manual or to obtain the illustrated parts catalog please visit the Bunn O Matic website at www bunn com This is absolutely FREE and the quickest way to obtain the latest catalog and manual updates Contact Bunn O Matic Corporation at 1 800 286 6070 to obtain a paper copy of the required Illustrated Parts Catalog mailed via U S Postal Service www bunn com 27038 0000H 5 12 1996 Bunn O Matic Corporation INTRODUCTION This equipment will brew a half gallon gallon or gallon and a half batch of coffee into an awaiting server at the push of a button and includes a hot water faucet for allied beverage use The brewer is specifically designed for use with a BUNN 1 5GPR server It is only for indoor use on a sturdy counter or shelf BUNN 0O MATIC COMMERCIAL PRODUCT WARRANTY Bunn O Matic Corp BUNN warrants equipment manufactured by it as follows 1 Airpots thermal carafes decanters GPR servers iced tea coffee dispensers MCP MCA pod brewers thermal servers and Thermofresh servers mechanical and digital 1 year parts and 1 year labor 2 All other equipment 2 years parts and 1 year labor plus added warranties as specified below a Electronic circuit and or contro
3. control assembly in the OFF position Models with electro mechanical thermostats Rotate the control thermostat knob fully counterclockwise to the OFF position 2 Connect the brewer to the power source Water will begin flowing into the tank 3 When water stops flowing into the tank remove the front panel and proceed as directed Models with electronic control assemblies Place the tank heater switch at the top of the control assembly in the ON position and replace the front panel Models with electro mechanical thermostats Rotate the control thermostat knob fully clockwise to the ON position and replace the front panel 4 Wait approximately twenty five minutes on 208V 240V Models or fifty minutes on 120V Models for the water in the tank to heat to the proper temperature 5 Place an empty server beneath the brew station Place the Selector switch in the one gallon position the On OFF switch in the upper position and initiate a brew cycle 6 Place the On Off switch in the lower OFF position after water has stopped flowing from the funnel and check the water volume in the server It should be 128 ounces 7 A If not adjust the timer as required Refer to Adjusting Brew Volumes B If necessary adjust the needle valve to achieve water volume to be bypassed around the coffee filter in the funnel NOTE To increase the water bypass turn the needle valve counterclockwise to decrease the water bypass turn the needle va
4. water flow As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration FDA this equipment must be installed with adequate backflow prevention to comply with federal state and local codes For models installed outside the U S A you must comply with the applicable Plumbing Sanitation Code for your area Page 4 27038 050412 PLUMBING HOOK UP NOTE If a backflow preventer is required by code a shock arrestor should be installed between backflow preventer and dispenser Installing the shock arrestor as close to dispenser as possible will provide best results 1 Attach the flare fitting from the short piece of tubing on the strainer flow control supplied to the water inlet fitting on the bottom of the brewer 2 Flush the water line and securely attach it to the flare fitting on the strainer flow control 3 Turn on the water supply INITIAL SET UP CAUTION The brewer must be disconnected from the power source throughout the initial set up except when specified in the instructions NOTE ECA Models Only This brewer is equipped with a temperature sensor that indicates when to brew and when selected locks out the start of a brew cycle until the water has heated to the optimum brewing tempera ture 1 Remove the front panel beneath the sprayhead Models with electronic control assemblies Place the tank heater switch at the top of the
5. ble Plumb ing Sanitation Code for your area A 00656 0001 37881 0000 WARNING REMOVE FUNNEL SLOWLY 03408 0004 MAIN ON OFF D SWITCH 00824 0002 A WARNING WAR A WARNING 00824 0001 Be oa 39803 0000 A WARNING Awarnnc DOAA WATER 03409 0004 anano 5600 A CAUTION BNP RSU 10 vel cw loa fers 12364 0000 Page 3 27038 050412 ELECTRICAL REQUIREMENTS WARNING The brewer must be disconnected from the power source until specified in nitial Set Up Refer to Data Plate on the Brewer and local national electrical codes to determine circuit requirements GREEN TG 120 volt ac models 200 and 230 volt ac models 120 208 amp 120 240 volt ac models Note This electrical service consists Note This electrical service consists Note This electrical service consists of 2 current carrying conductors of 2 current carrying conductors of 3 current carrying conductors L1 and L2 and a separate conduc L1 and L2 anda separate conduc Neutral L1 and L2 and a separate tor for earth ground tor for earth ground conductor for earth ground ELECTRICAL HOOK UP CAUTION Improper electrical installation will damage electronic components 1 An electrician must provide electrical service as specified 2 Using a voltmeter check the voltage and color coding of each conductor at the electrical source 3 Remove the front panel beneath the sprayhead
6. dition Replace unreadable or damaged labels 2 WARNING Fill water tank before turning on thermostat or connecting appliance to power source Use only on a properly protected circuit capable of the rated load Electrically ground the chassis Follow national local electrical codes DISCARD DECANTER IF CRACKED SCRATCHED BOILED DRY HEATED WHEN EMPTY USED ON HIGH FLAME FUNNEL CONTENTS OR EXPOSED ELECTRIC ARE HOT ELEMENTS Do not use near combustibles FAILURE TO COMPLY RISKS EQUIPMENT READ THE ENTIRE OPERATING MANUAL DAMAGE FIRE OR SHOCK HAZARD BEFORE USING THIS PRODUCT FAILURE TO COMPLY RISKS INJURY PN 00658 0000F 6 98 1985 BUNN O MATIC CORPORATION A THIS APPLIANCE IS HEATED WHENEVER 00658 0000 CONNECTED TO A POWER SOURCE N 00831 0000F 3 98 1998 BUNN O MATIC CORPORATION 00831 0000 READ THE ENTIRE OPERATING MANUAL BEFORE BUYING OR USING THIS PRODUCT As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration FDA this equipment must be installed with adequate To reduce the risk of electric shock do not remove or open cover No user serviceable parts inside Authorized service personnel only Disconnect power before servicing backflow prevention to comply with federal state and local codes For models installed outside the U S A you must comply with the applica
7. f capital cost of down time cost of substitute equipment facilities or services or any other special incidental or consequential damages 392 AutoPOD AXIOM BrewLOGIC BrewMETER Brew Better Not Bitter BrewWISE BrewWIZARD BUNN Espress BUNN Family Gourmet BUNN Gourmet BUNN Pour O Matic BUNN BUNN with the stylized red line BUNNlink Bunn OMatic Bunn O Matic BUNNserve BUNNSERVE with the stylized wrench design Cool Froth DBC Dr Brew stylized Dr design Dual Easy Pour EasyClear EasyGard FlavorGard Gourmet Ice Gourmet Juice High Intensity iMIX Infusion Series In tellisteam My Caf Phase Brew PowerLogic Quality Beverage Equipment Worldwide Respect Earth Respect Earth with the stylized leaf and coffee cherry design Safety Fresh savemycoffee com Scale Pro Silver Series Single Smart Funnel Smart Hopper SmartWAVE Soft Heat SplashGard The Mark of Quality in Beverage Equipment Worldwide ThermoFresh Titan trifecta Velocity Brew A Partner You Can Count On Air Brew Air Infusion Beverage Bar Creator Beverage Profit Calculator Brew better not bitter BUNNSource Coffee At Its Best Cyclonic Heating System Daypart Digital Brewer Control Nothing Brews Like a BUNN Pouring Profits Signature Series Tea At Its Best The Horizontal Red Line Ultra are either trademarks or registered trademarks of Bunn O Matic Corporation Page 2 27038 030912 USER NOTICES The notices on this brewer should be kept in good con
8. ill not stop the flow of water from the funnel Placing the switch in the lighted upper position supplies power to the brew station warmer and enables the brew circuit START SWITCH Momentarily pressing and releasing this switch starts a brew cycle when the On Off switch is in the lighted upper position NOTE The On Off switch must be in the lighted upper position to initiate and complete a brew cycle COFFEE BREWING 1 Select the desired batch size Insert a BUNN filter into the funnel Pour the proper amount of fresh coffee into the filter and level the bed of grounds by gently shaking Slide the funnel into the funnel rails Place an empty server under the funnel Place the On Off switch in the lighted upper position Momentarily press and release the start switch When brewing is completed simply discard the grounds and filter OO oS CLEANING 1 The use of adamp cloth rinsed in any mild non abrasive liquid detergent is recommended for cleaning all surfaces on Bunn O Matic equipment 2 Check and clean the sprayhead The sprayhead holes must always remain open NOTE In hard water areas this may need to be done daily It will help prevent liming problems in the brewer and takes less than a minute Page 7 27038 091900
9. ipment is under warranty THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY WRITTEN OR ORAL EX PRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE The agents dealers or employees of BUNN are not authorized to make modifications to this warranty or to make additional warranties that are binding on BUNN Accordingly statements by such individuals whether oral or written do not constitute warranties and should not be relied upon If BUNN determines in its sole discretion that the equipment does not conform to the warranty BUNN at its exclusive op tion while the equipment is under warranty shall either 1 provide at no charge replacement parts and or labor during the applicable parts and labor warranty periods specified above to repair the defective components provided that this repair is done by a BUNN Authorized Service Representative or 2 shall replace the equipment or refund the purchase price for the equipment THE BUYER S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS EQUIPMENT WHETHER DERIVED FROM WARRANTY OR OTHERWISE SHALL BE LIMITED AT BUNN S SOLE OPTION AS SPECIFIED HEREIN TO REPAIR REPLACEMENT OR REFUND In no event shall BUNN be liable for any other damage or loss including but not limited to lost profits lost sales loss of use of equipment claims of Buyer s customers cost o
10. itch until three distinct clicks are heard and then release the switch Failure to release the switch within two seconds after the third click causes the volume setting to be aborted and previous volume setting will remain in memory View the level of the liquid being dispensed When the desired level is reached turn the ON OFF switch to OFF lower The brewer remembers this volume and will continue to brew batches of this size until the volume setting procedure is repeated NOTE When brewing coffee batch volumes will decrease due to absorption by the coffee grounds 3 Setting programming disable feature If it becomes necessary to prevent anyone from changing brew times once programmed you can set the SET LOCK switch to the LOCK position This will prevent any program ming to be done until switch is once again placed in the SET position NOTE If the clicks can not be heard lightly grip the incoming water line to feel when the valve cycles on and off Page 6 27038 011110 OPERATING CONTROLS BREW SELECTOR SWITCH Placing the switch in the Gal 1 Gal or 1 Gal position selects the amount of coffee to be brewed in sub sequent brew cycles Repositioning this switch after a brew cycle has been initiated does not change the brew batch in progress ON OFF SWITCH Placing the switch in the unlighted lower position cuts power to the brew station warmer and stops brew ing Stopping a brew cycle after it has been started w
11. l boards parts and labor for 3 years b Compressors on refrigeration equipment 5 years parts and 1 year labor c Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis parts and labor for 4 years or 40 000 pounds of coffee whichever comes first These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by it will be commercially free of defects in material and workmanship existing at the time of manufacture and appearing within the applicable warranty period This warranty does not apply to any equipment component or part that was not manufactured by BUNN or that in BUNN s judgment has been affected by misuse neglect alteration improper installation or operation improper maintenance or repair non periodic cleaning and descaling equipment failures related to poor water quality damage or casualty In addition the warranty does not apply to replacement of items subject to normal use including but not limited to user replaceable parts such as seals and gaskets This warranty is conditioned on the Buyer 1 giving BUNN prompt notice of any claim to be made under this warranty by telephone at 217 529 6601 or by writing to Post Office Box 3227 Springfield Illinois 62708 3227 2 if requested by BUNN shipping the defective equipment prepaid to an authorized BUNN service location and 3 receiving prior authorization from BUNN that the defective equ
12. lve clockwise An adjustment to the needle valve will require a timer adjustment for volume Repeat step 7 until the proper water volume is achieved 9 The brewer is now ready for use in accordance with the coffee brewing instructions 2 Pag e 5 27038 100407 CE REQUIREMENTS e This appliance must be installed in locations where it can be overseen by trained personnel e For proper operation this appliance must be installed where the temperature is between 5 C to 35 C e Appliance shall not be tilted more than 10 for safe operation e An electrician must provide electrical service as specified in conformance with all local and national codes e This appliance must not be cleaned by water jet e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given instructions concerning use of this appliance by a person responsible for its safety e Children should be supervised to ensure they do not play with the appliance e Ifthe power cord is ever damaged it must be replaced by the manufacturer or authorized service personnel with a special cord available from the manufacturer or its authorized service personnel in order to avoid a hazard ADJUSTING BREW VOLUMES CAUTION Disconnect the power source from the brewer prior to the removal of any panel for the replacement or adjustment of any component NOTE Pri
13. or to setting or modifying batch sizes check that the brewer is connected to water supply the tank is properly filled and a funnel and server are in place 1 Modifying batch sizes To modify a batch volume first check that the SET LOCK switch is in the SET posi tion on the circuit board To increase a batch size Press and hold the START or BREW switch until three clicks are heard Release the switch Failure to release the switch within two seconds after the third click causes the volume setting to be aborted and previous volume setting will remain in memory and press it again one or more times Each time the switch is pressed two seconds are added to the brew time period Allow the brew cycle to finish in order to verify that the desired volume has been achieved To decrease a batch size Press and release the START or BREW switch once for every two second interval to be removed from the total brew time period then immediately press and hold down the START or BREW switch until three clicks are heard Release the switch Failure to release the switch within two seconds after the third click causes the volume setting to be aborted and previous volume setting will remain in memory Allow the brew cycle to finish in order to verify that the desired volume has been achieved 2 Setting batch sizes To set a batch volume first check that the SET LOCK switch is in the SET position on the circuit board Press and hold the START or BREW sw
Download Pdf Manuals
Related Search