BT PC Scanner All in One Printer User Manual
Contents
1. 272155 CS 2016FM The Informer 117 2 Way FM Paging Alarm amp Remote Engine Starting System OPERATION INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of the Informer II by Crimestopper Security Products Inc This booklet contains the information necessary for operating your system If any questions arise contact your installation dealer or Crimestopper Security Products Inc IMPORTANT INFORMATION Primary and Optional Features PRIMARY These are features that must be connected in order for the system to operate properly i e Power Ground LED etc OPTIONAL Optional features are connected only if desired or agreed upon by the installing dealer i e Horn Honk Dome light illumination Door Locks Trunk Pop etc These features may require additional parts and labor charges Consult with your installer about these features BEFORE installation CONTACT INFORMATION TECHNICAL SUPPORT 800 998 6880 Monday Friday 8 00am 4 30pm Pacific This device complies with FCC Rules part 15 Operation is subject to the following two conditions 1 This device may not cause interference and 2 this device must accept any interference that Website www crimestopper com may be received including interference that may cause undesired E mail tech support crimestopper com operation The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this CRIMESTOPPER equip2. CONFIRM REMOTE SUCCESFUL START START REQUEST REMOTE ENGINE CONTROL UNSUCCESSFUL REMOTE START In the event that the engine does not start on the first attempt the system shuts down for a few seconds then attempts to restart the engine 2 and 3 time For hard starting engines the unit will allow a starter crank time of up to13 seconds maximum This should provide ample cranking time for difficult starts but is limited to 13 seconds to help prevent damage to the starter from over cranking 1 If engine starts 274 or 3 attempt see steps 4 amp 5 on last page under Successful Start 2 If Third attempt fails to start engine the system will turn off and doors will remain locked NO FURTHER ATTEMPTS WILL BE MADE AUTOMATICALLY UNLESS YOU PRESS THE REMOTE START BUTTON AGAIN TURNING OFF YOUR REMOTE STARTED ENGINE VIA REMOTE CONTROL 1 Engine is running in Remote Start Parking lights ON 2 Press Remote Start button on remote transmitter 3 Engine amp parking lights turn OFF Doors remain locked or will re lock if applicable Qe ENGINE amp LIGHTS OFF ENTERING YOUR REMOTE STARTED VEHICLE 1 With engine running Remote Unlock Disarm system If armed or open door with key 2 Enter vehicle and be careful not to step on brake pedal Remote Start Reset 3 Turn Ignition to ON RUN position then press brake pedal to reset the Remote Starter amp Shift out of park 4 Remote starter will re
3. 2004 Crimestopper Security Products
4. ea 18 19 Low Battery Warning LCD Remote Setting Clock LCD 19 20 OPERATION CAUTIONS amp WARNINGS CRIMESTOPPER SECURITY PRODUCTS INC and its VENDORS shall not be liable for any accident resulting from the use of this equipment This system is designed to be professionally installed into a car or vehicle in good running order Items such as parking brake door switches and all engine safety features must be in perfect working condition DAMAGE resulting from misuse or negligence is NOT covered under warranty and will be subject to repair or replacement charges IT IS ABSOLUTELY THE OWNER S SOLE RESPONSIBILITY TO A Understand the operation of this system and its safety features B Check for proper operation of these safety features prior to accepting delivery of the vehicle from the installation facility C Check and maintain the condition of the vehicle and all items relative to the proper operation of this system and its safety features DO NOT remote start the vehicle in a closed garage Make sure that the vehicle is outdoors a garage door is open or there is adequate exhaust ventilation Failure to observe this rule could result in injury or death from poisonous Carbon Monoxide fumes This is especially important when using the Timed Self Start feature of the unit 2 TRANSCEIVER PAGER REMOTE PAGER REMOTE TRANSCEIVER The hand held remote transce
5. Press and release to Start Stop engine BUTTON 5 Upper side button of remote e Press for convenient flashlight function The high power LED acts as a mini flashlight BUTTON 6 Lower side button of remote 6 VEHICLE 2 4 REMOTE START e Press and release to activate Vehicle 2 mode Led witl flash for 4 second to use vehicle 2 otherwise remote will revert back to Vehicle 2 OPERATING INSTRUCTIONS ALARM Active Arming Locking Press button 1 Lock symbol on the transceiver The System will arm emit one siren chirp one light flash and the LED will begin to flash Power locks will lock if equipped Starter disable circuit will turn on LCD Pager will beep once while displaying a Down Arrow and a Lock symbol followed by the CSP logo After a short delay to allow the vehicle and electronics to settle the system will be completely armed Disarming Unlocking Press button 2 Unlock symbol on the transceiver System will disarm and confirm with two siren chirps two light flashes and the LED will turn off Power locks will Unlock and Interior Dome light will turn on if installed with these optional features LCD Pager will beep twice while displaying an Up Arrow and an Unlock symbol followed by the CSP logo DISARM UNLOCK Alarm Triggers If there is an intrusion into the vehicle a hard impact to the body or the ignition is turned on the alarm will sound and flash the lights for
6. a confirmation that the unit is in Timed Self Start Mode 6 The Vehicle will Start by itself every 4 hours or until driven with key or started via remote control WITHIN 10 SEC w CA PRESS 1X LIGHTS OFF 5 SEC UNLOCK O eae 4X 24 LOCK RESETTING TIMED SELF START MODE To reset the timed self start mode start the vehicle using the key or the manually with the remote control 12 OPTIONAL TURBO TIMER MODE OPTIONAL TURBO TIMER MODE IMPORTANT NOTE This mode requires the use of an extra part called a momentary switch or button that is not included with the kit Check with your installer about adding this feature The optional Turbo Timer mode allows the your system to keep your vehicle running for 1 to 5 minutes selectively after you remove the key exit the vehicle and lock the doors remotely if you own a Turbo or Turbo Diesel This is handy for turbo cool down without the need for expensive Turbo Timers 1 Engine should be running with the key Press and hold the brake pedal 2 Press your Turbo Timer button 1 to 5 times for each minute of run time you desire 1 press 1 min 3 Release the brake pedal and your system will confirm by flashing the lights the same number of times the button was pressed 4 Turn Ignition switch OFF remove key and exit the vehicle Remote lock your doors for safety The engine should remain running for the selected number of minutes PRESS TURBO RUNNING P
7. 1 minute After 1 minute the trigger cycle will automatically stop and alarm will remain armed to continue protecting the vehicle If a door is left open after an intrusion then the unit will cycle a maximum of 5 minutes and continue to protect the other un tampered or unopened zones LCD Remote Paging Zone Violations When the system is triggered the alarm sends a paging signal to the remote If you are within range you will receive a violation paging signal which consists of a vibration followed by 15 audible beeps to notify you the vehicle has been tampered with DOOR TRIGGER SHOCK TRIGGER HOOD TRUNK TRIGGER IGNITION TRIGGER OPERATING INSTRUCTIONS ALARM Disarming While Tripped Triggered Disarming the System while it is triggering requires TWO presses of the 2 Unlock Button The first press of Button 2 Resets the alarm cycle only system still armed while a second press will disarm unlock the system Selective Silent Arming Disarming To Arm or Disarm the system without siren chirps press and release both Buttons 2 Unlock and 4 Start at the same time System will Arm or Disarm without siren chirps Flashing lights and LED will be the only indicators of Arm Disarm status The LCD will Display a musical note with an X when the system is armed or disarmed without a chirp Prior intrusion Alert This system will notify you if the alarm was tripped while you where away Upon d
8. RESS TIMER BUTTON AND HOLD 1 5 TIMES BRAKE gt Ba gt 0 8 o gt gt LIGHTS Sena REMOVE KEY REMAIN RUNNING EXIT 1 5 MIN 13 ANTI CARJACK PROTECTION REMOTE OPERATED CARJACK PROTECTION This feature provides Active Carjack protection through the remote control When the Ignition is on vehicle is running press and hold the 1 LOCK Button and 3 TRUNK Button for 2 seconds The parking lights will flash 2 times and the LED will begin to flash rapidly to confirm the beginning of a Carjack countdown 30 Seconds later the unit will begin a Carjack Cycle consisting of 20 seconds of pre warning chirps turning into a full system activation with siren flashing light pulses for up to 5 min If the Ignition is turned off during a Carjack trigger the siren and lights stop but Carjack protection is still active The Siren and Lights will resume if the Carjacker tries to turn the Ignition back ON TO RESET Press Button 2 UNLOCK on the remote and the siren will chirp once or turn the key on and press and hold the override button for at least 5 seconds SWITCH CONTROLLED amp FULL TIME CARJACK PINK WIRE CONFIGURATION This feature can provide Passive or Manual control Carjack protection depending on the configuration of the Pink Carjack wire of the alarm system The system must be programmed for the Pink wire to be used as a Carjack trigger with programming option 8 Once programmed for the Pink wire for use as a Carjack trigg
9. a second transmitter or transceiver the unit will flash 3 times indicating its waiting for the 3 code and lights will flash 4 times for 4 code If all 4 codes are learned the unit will automatically exit code learning mode otherwise turn key off and close hood NOTE When learning 2 Way FM remotes wait for the LCD to confirm with a beep and the antenna ICON on the LCD screen BEFORE learning the next remote SEE DIAGRAM ON NEXT PAGE 19 TRANSCEIVER REMOTE CONTROL PROGRAMMING oe S IGN gt OFF gt gt gt WAIT FOR BLUE WIRE GROUNDED 4 FLASHES PRESS 4X s 2 WAY SYSTEMS amp SideKick REMOTES 8 FLASH 2 3 or 4 X s fa IGN gt gt LOCK amp COMPLETE UNLOCK PRESS TOGETHER LCD Code Learn Screen 16 2 VEHICLE OPERATION 2 VEHICLE CONTROL Your CS 2016FM remotes have the ability to control a second vehicle with a Crimestopper CS 2016FM or older CS 2015FM system installed See diagram below on how to switch your remote s to vehicle 2 operation To set up the 2 Vehicle operation you must first program your remotes to Vehicle 2 Follow the Transmitter VEHICLE 2 CONTROL Programming steps Pg 13 at the second vehicle and learn YOUR remote Sidekick CS 2016FM along with vehicle 2 s existing remotes Remote 2 VEHCLE OPERATION NOTES gt 1 You do not have to switch between Vehicle and II to get pages from each vehicle Your remote pager will recei
10. cess of your vehicles Audio Cellular Navigation or Entertainment systems This feature is OPTIONAL and requires extra parts and labor for installation Consult your installation dealer about MAP before or during installation 52016 must be programmed for MAP operation When the system is put into Valet Park mode M A P will prevent stereo entertainment navigation or cellular system from being used 8 REMOTE ENGINE CONTROL REMOTE ENGINE STARTING SUCCESSFUL START 1 Press remote start button on the remote transmitter System will chirp 3 times for audible confirmation Chirps can be programmed on or off See installation manual Parking lights flash once then turn on solid Ignition Accessory circuits turn on After a few seconds Starter Motor engages Parking lights and Accessory circuits turn off while cranking Engine Starts and Runs Parking Lights and Accessory turn back on Doors Lock Engine will remain running for programmed run time until reset with Brake pedal If needed the engine can be turned off with remote transmitter 5 2 4 5 REMOTE ENGINE STARTING SUCCESSFUL START DIAGRAM REMOTE ENGINE STARTING LCD PAGER REMOTE When requesting a remote start the LCD pager remote will confirm with an Ignition Icon along with 4 beeps Once the vehicle has successfully started the remote will confirm back with 2 vibrations a moving vehicle Icon and 4 beeps
11. e system See 2 Way FM Transceiver programming for more information LOW BATTERY WARNING LCD REMOTE Your 2 Way pager remote will warn you when the battery gets low You will see a battery L icon on the LCD screen when it is time to replace the AAA battery You may also irregular long siren chirps when arming and disarming you system To replace the battery simple unlatch and slide open the battery door on the back of the 2 Way LCD remote Carefully insert a new battery using the outline on the bottom of the battery compartment as a guide Your remote will beep once if the battery was inserted correctly LOW BATTERY WARN 19 SETTING THE CLOCK 2 WAY LCD REMOTE Press and hold all 4 buttons of remote control for approximately 3 seconds until remote beeps 2 The minute display will begin flashing Use the lock and unlock button to change the minute up or down to the correct time and then press button 3 Trunk to set the minute value 3 The hour display should begin flashing Use the lock and unlock button to change the hour up or down to the correct am or pm hour 4 Once the correct time is displayed wait 6 seconds the remote will beep twice and the time of day is set 20 Crimestopper Security Products Inc 1770 So Tapo Street Simi Valley CA 93063 800 998 6880 ONLINE TECHNICAL SUPPORT www crimestopper com www crimestopper com techweb03 html email crimestopper com
12. er it can be configured in different ways to provide different levels of protection It can be connected to a hidden 12V toggle momentary switch or to 12V Ignition Power Read following sections for further descriptions HIDDEN SWITCH CONTROLLED CARJACK This configuration will enable the vehicle owner to activate a Carjack countdown by pressing a hidden push button not included with kit during a Carjack situation A Carjack countdown will begin under the following conditions Ignition is ON vehicle is running the push button is pressed and the door opens closes Upon these 3 events in that order the alarm will start a Carjack countdown After a delay of one minute the system will begin chirping for 20 seconds then trigger into a full cycle for up to 5 minutes To reset this Carjack mode Ignition must be ON then press and hold the override valet button for 5 seconds until LED goes out FULL TIME Permanent CARJACK We recommend that this configuration only be used if a serious threat of Carjack exists during everyday situations When the Ignition is on vehicle is running anytime a door is opened the Carjack countdown sequence will be initiated There will be 2 light flashes and the LED will change from solid to quick pulsing as confirmation of a countdown sequence To reset FULL TIME Carjack the Ignition has to be ON then press and hold the override program button 5 seconds until LED stops pulsing The LED will be on SOLID when in t
13. his mode anytime the Ignition is ON or while driving as a reminder that Carjack is waiting for a door to open 14 LED DIAGNOSTICS The CS 2016FM system includes disarm diagnostics through the RED LED light that will help in determining what caused the last trigger of the alarm system This is a valuable tool in determining how the vehicle was tampered with or if there is a false alarm problem in which case you can make the necessary adjustments to correct the problem When the system is disarmed with the remote you will hear the normal 2 chirps then 4 quick chirps that indicate the alarm was triggered while you were away Check the LED light for a sequence of flashes Shock Sensor 1 Flash Door 2 Flashes Hood Trunk 3 Flashes Ignition 4 Flashes Diagnostics will reset when the Ignition is turned on or when the system is re armed TRANSCEIVER REMOTE CONTROL PROGRAMMING Note All transmitter codes must be learned at time of programming Up to 4 different transmitter codes can be stored in the memory of the system 1 Open Hood Ground the Blue wire if no hood pin is installed 2 Turn key to the ON position 3 Press Programming button 4 times then after a few seconds the unit will flash the parking lights 4 times 4 Press buttons 1 Lock amp 2 Unlock together at the same time of each transceiver to be learned You should get 2 light flashes indication the unit is waiting for 274 code then press button 1 amp 2 of
14. isarming the two normal disarm chirps will be heard then the system will emit 4 additional siren chirps Check your vehicle for any signs of a break in or tampering Also see LED Diagnostics Section to determine the cause of the trigger Remote Panic Protection To sound the alarm in an emergency situation or to draw attention to your vehicle press and hold Button 1 Lock for at least 3 seconds until the siren sounds Press Button 2 Unlock to reset panic mode The LCD pager remote will display a P and emit 15 beeps when the panic mode is triggered SILENT DISARM 1 Selective Shock Sensor Disable To arm the alarm and bypass shock sensor protection press Button 1 as normal then PANIC MODE press and release Button 1 and 2 together within 2 seconds You will hear 3 extra siren chirps indicating shock sensor bypass for this arming cycle only This feature can be used when parking near railroad tracks airports or area with excessive loud machinery or noise to prevent the nuisance of unnecessary false alarms Open Door Alert Bypass Upon arming this system will warn you if a door is left open The LCD pager will vibrate and beep 15X s along with displaying the open zone on your LCD screen This zone will automatically be bypassed until closed otherwise the alarm will continue to protect all other zones OPERATING INSTRUCTIONS ALARM Pre Warning Shock Protection The Pre warning warn a
15. iver is used to send and receive information from the vehicle The Control Module transmits High Frequency FM signals from the vehicle to your over long distances Your range will vary depending on location terrain and local RF noise interference This system is not guaranteed to page you if you are behind concrete walls underground in a SCREEN large structure or in an area with high levels of electronic 5 interference Handle the pager remote with care if the LCD RECALL display and or the electronics may be damaged if subjected to eer abuse AAA Cell 1 5V alkaline battery can easily be UNLOCK replaced by sliding open the battery access door on the back of 1 ARM the remote Battery life will vary depending on usage The LCD LOCK AENDE screen will display a low battery icon when the battery is low 3 TRUNK START STOP For more on range see Range Questions on page 15 POP ACTIVE 2 ZONE LCD DISPLAY The unique LCD screen includes both a Dot Matrix animated display and a vehicle icon Itis designed to show you both Icon based information and animated messages in real time as it is happening When the alarm is disarmed or armed with no activity to report then dot matrix portion of the screen will remain BLANK BUTTON 1 Lock Symbol e Press and release to Arm Lock system e Press and Hold for more than 3 seconds to activate Panic feature BUTTON 5 On side of remote Press and Release to Recall
16. ment Such modification could void the user s authority to SECURITY PRODUCTS INC operate the equipment 1770 5 TAPO STREET SIMI VALLEY CA 93063 09 2004 TABLE OF CONTENTS Operation Cautions amp 65 1 0 011 1 1 4 10 2 Transceiver von oda Ai apr aaae eii E de steer EEANN EEEa F iai 3 CS 397TW Sidekick Remote Control ccciccicssccieedeveccceeseteesndetan vie dieses 4 Operating Instructions 2 2542 2 deaud i Paana ak 4 8 oe EAA EASE 9 13 Protection hd dace EEA EA 14 LED DIAQnOSUCS Sew 15 Transceiver Remote Control 15 16 2 17
17. o law enforcement vehicles or commercial vehicles that need to remain running unattended for long periods of time INFINITY RUN MODE EXITING THE VEHICLE 1 Follow steps for IDLE DOWN MODE EXITING THE VEHICLE above except press the remote start button a second time within 10 seconds at STEP 1 2 Parking Lights will start flashing instead of coming on solid and doors will unlock 3 Turn Ignition switch OFF remove key and exit the vehicle Engine should remain running 4 The vehicle s parking lights will flash for the programmed run time of 12 24 or 36 or 48 minutes and then switch to solid while motor runs indefinitely or until fuel supply runs out 11 REMOTE ENGINE CONTROL TIMED SELF START MODE This mode allows the vehicle to be programmed to self start every 4 hours and run for the programmed run time This can be helpful during extremely cold conditions where engine or fluid freeze up is a concern THE VEHICLE MUST BE OUTDOORS OR IN A WELL VENILATED AREA TIMED SELF START MODE EXITING THE VEHICLE 1 Have engine running with the Key then press the Start button on the transmitter 2 Within 10 seconds press the valet program button once 3 Parking Lights will turn OFF for about 5 seconds and doors will unlock 4 Turn Ignition switch OFF remove key and exit the vehicle Engine should remain running 5 Press the remote start button again to turn off the engine The parking lights will flash 4 TIMES as
18. rvicing or otherwise turn the ignition on and press the override program button about 5 7 seconds until you hear 3 siren chirps and the LED turns on solid Repeat the process to exit VALET mode To enter exit valet via the remote press and hold both buttons 1 Lock and Button 2 unlock together for about 3 seconds until 3 chirps are heard Repeat this step to exit via the remote transmitter Lock Unlock and AUX features will still operate in when in VALET mode however remote start and alarm functions are inhibited Valet Park Mode Using the remote transmitter only Note Valet Park mode is only accessible when using the remote transmitter Valet park mode allows you to turn over the vehicle to a valet allowing access to drive lock unlock your vehicle but alarm will trigger if the trunk is opened To activate Valet Park press and hold both buttons 1 Lock and Button 2 unlock together for about 6 seconds 3 chirps will be heard first when unit goes into regular Valet and as you continue to hold both buttons you will hear 2 more chirps LED will always flash slowly when in Valet Park even when the Ignition is turned on or driving vehicle Repeat step above to exit Valet Park mode a l VALET UNLOCK VALET MODE Optional M A P Mobile Accessories Protection This system can be programmed to provide Crimestopper s unique M A P Mobile Accessories Protection feature that allows you to prevent unauthorized ac
19. set instantly when the brake is pressed Parking lights will turn off and the ignition key is now controlling your vehicle REMOTE ENGINE CONTROL IDLE DOWN MODE TAKE OVER OPERATION This mode allows the unit to take over operation of your idling parked vehicle while the ignition key is removed and you exit the vehicle The vehicle is put into a remote running condition before you exit and it will remain running for the programmed run time until you return or until the remote start button is pressed Example You pull up to a convenience store for a quick stop Idle Down mode keeps engine running when you exit the vehicle with keys in hand remote lock arm alarm When you return unlock disarm alarm turn ignition ON and drive away This mode can also be used on Turbo vehicles that need idle for cool down IDLE DOWN MODE EXITING THE VEHICLE 1 With engine running press Remote Start button on remote transmitter Siren will chirp 3 times for confirmation 2 Parking Lights will turn ON 3 Doors will unlock or if brake pedal is being depressed then doors will unlock when it is released 4 Turn OFF Ignition and remove key Engine should remain running 5 Exit vehicle then remote lock doors if desired 6 Engine will remain running for programmed run time until you return or press the remote start button INFINITY RUN MODE This mode allows the vehicle s engine to remain running INDEFINITELY This mode can be beneficial t
20. smitter to pop open the trunk hatch If the system is armed it will also disarm when the button 3 is pressed The LCD pager remote will confirm with 3 beeps and the trunk icon on the screen Remote AUX Output 2 Optional Requires special programming TRUNK POP This system contains a second auxiliary output to activate other accessories or devices To activate the systems Second Auxiliary Output press and HOLD Button 3 Trunk Symbol on the transmitter for more than 2 seconds This is a momentary output that will stay active as long as the remote button is held down There is no LCD pager confirmation for Aux 2 output Dome Light Illumination Optional This feature will turn on the vehicle s dome light upon disarming for 30 seconds or until the key is inserted and turned on This will provide illuminated entry to your vehicle in dimly lit areas for safety and security 7 OPERATING INSTRUCTIONS ALARM Emergency Override Disarm If you have lost the transmitter or it stops working for any reason and the Alarm is armed you will have to disarm the system manually Open the door with the key alarm will sound turn the ignition on and press the override program button for about 5 seconds The Alarm will disarm and allow you to use the vehicle until you can repair replace the remote Valet mode also prevents Passive Arming Valet Mode Enter manually or using the remote To disable Alarm and Remote Engine Starting for vehicle se
21. the last message from the LCD screen BUTTON 2 Unlock Symbol Press and Hold for 3 seconds to e Press and release to Disarm Unlock system or reset a cycle change from Car 1 to Car 2 Only BUTTON 3 Trunk Symbol for use with 2 car operation e Press and Release to activate trunk pop Auxiliary output 1 Optional Press 5 times to Disable Enable Feature audible beep tones from the remote Remote will vibrate twice e Press and Hold to activate a second optional feature Auxiliary output to confirm silent mode 2 BUTTON 4 Key e Press and release to Start Stop engine 3 CS 397TW SIDEKICK REMOTE The CS 397TW 1 Way sidekick remote adds flexibility to your CS 2016FM You can have the convenience of operating your system without needing to carry the larger pager remote The Sidekick remote has less range and offers all of the same 2 UNLOCK DISARM 5 operation features except for page back FLASHLIGHT confirmation See diagram below for Sidekick 1 Way remote operation BUTTON 1 Lock Symbol e Press and release to Arm Lock system e Press and Hold for more than 3 seconds to activate Panic feature BUTTON 2 Unlock Symbol e Press and release to Disarm Unlock system or reset a cycle BUTTON 3 Trunk Symbol e Press and Release to activate trunk pop Auxiliary output 1 Optional Feature e Press and Hold to activate a second optional feature Auxiliary output 2 BUTTON 4 Key e
22. the remote pager is operating from the AAA 1 5V alkaline battery This is a normal feature for an FM 2 Way paging system 2 Your system is designed to always operate with maximum efficiency however range may be affected by the following circumstances Physical Distance Obstructions and RF Electronic Interference On US Domestic systems power output is limited by FCC Regulations Specifications 3 This CS 2016FM system does NOT use Paging or Cellular antenna service There are no monthly fees associated with its operation The CS 2016FM unit in the vehicle sends a paging signal directly to your pager remote from its own antenna mounted inside the vehicle MY IN DASH LED FLICKERS WHEN PRESSING REMOTE CONTROL BUTTONS This is normal operation There may be a slight flicker visible from the LED when pressing the remote as the system is authorizing processing the code sent from the remote control There is nothing wrong with your system MY SYSTEM FLASHES THE LIGHTS ONCE AND WILL NOT ATTEMPT A REMOTE START 2 parts 1 The system is possibly in valet mode Check the status of the RED LED light If it is on solid then the unit is in VALET MODE and will NOT remote start when in Valet mode This is to protect the system from unauthorized engine starting when your vehicle serviced or valet parked TO EXIT VALET MODE Turn Ignition ON and press the valet button for about 5 seconds until LED goes out See the Valet part of the operating ins
23. tructions for more information 2 The unit senses a possible wiring fault at the Brake or the Hood is OPEN Blue wire grounded This is a safety feature of the unit Check installation for faults and make sure hood is closed and verify brake input connection The LCD will also not confirm back a signal of a remote start request when this occurs 18 TROUBLESHOOTING continued WHEN ARMING AND DISARMING MY ALARM HAS IRREGULAR LONG SIREN CHIRPS This is an audible warning that the battery in the LCD pager remote is low Replace the AAA battery in the pager and your chirps will return to normal SYSTEM IS NOT SUCCESSFUL AT REMOTE STARTING DURING EXTREME COLD CONDITIONS Please be aware that during sub freezing conditions your remote starter may take more that one attempt to start or it may not successfully start the vehicle after 3 attempts During these conditions the vehicle may not properly start even using the key therefore trying to start the vehicle by remote would also be unsuccessful MY SYSTEM DOES NOT RESPOND TO THE REMOTE CONTROL 4 Parts 1 You may be out of range of your vehicle Move closer and attempt again 2 Check for proper power ground wiring connections of the alarm 3 Check Antenna Module connection The antenna included with this system must be plugged in to send receive signals Antenna Module gets voltage from the control module 4 The Remote Pager may need a new battery or need to be reprogrammed to operate th
24. ve 6 pages from both cars regardless of which vehicle the pager is set to The I or icon will always display with each page indicate which vehicle the page CrimeStopper Originated from 2 When programming CS 2016FM Press amp release side systems all remote pagers and sidekick button then you have remotes for that vehicle must be learned y at the time of programming When you 4 seconds to Press amp hold side button program your remote at the second control vehicle 2 for 5 seconds Remote vehicle that vehicle s original remote will beep and II icon will must also be programmed Your remote appear in lower right LCD should be set in Vehicle and the vehicle s original remote should be set in Vehicle 1 17 TROUBLESHOOTING BEFORE YOU CALL SECTION Before calling your dealer or Crimestopper read the following section for tips that may remedy or explain your problem RANGE QUESTIONS 2 Way Pager Remote Your CS 2016FM system uses FM High Frequency signals to send receive data between the pager and the vehicle and from the vehicle to the remote for state of the art operation 1 Under normal operation the distance from the vehicle paging the remote will be greater than that from the remote to the vehicle This is due to power supplies The main control module brain in the vehicle is connected to the electrical wiring receiving power from the vehicle battery whereas
25. way feature will activate when a low level shock or vibration detected by the system s shock sensor The alarm will chirp the siren 5 times flash the lights once to help deter any further tampering with the vehicle i pager remote will vibrate twice and beep 15X s 9 Passive Arming Mode Programmable PRE WARN Passive automatic arming occurs 30 seconds after the ignition is turned off and the last door is closed Upon closing the last door the unit will flash the lights twice and LED will be flashing rapidly to confirm passive countdown If a door is reopened within the 30 second period the countdown stop and begin again when the door is closed Passive arming provides failsafe protection in case you forget to arm the system Passive Locking Programmable The CS2016FM system can be programmed to passively lock the doors when the system passively arms The default setting is OFF because passive locking increases the risk of locking the keys in the vehicle When the system arms locks passively without you pressing the remote the LCD pager will still provide a confirmation signal The LCD screen will have an arrow only without a lock symbol Trunk Hatch Pop Optional Remote AUX Output 1 This feature is designed to interface with existing Factory power trunk or power hatch release systems and may require additional parts and or labor charges Press and release Button 3 Trunk on the tran
Download Pdf Manuals
Related Search