Brother MFC-3420C All in One Printer User Manual
Contents
1. The cable must not be bent or compressed The cable must be checked regularly and replaced by authorised technicians only see Assistance The manufacturer declines any liability should these safety measures not be observed Your appliance is supplied with a 13amp fused plug that can be plugged into a 13amp socket for immediate use Before using the appliance please read the instructions below WARNING THIS APPLIANCE MUST BE EARTHED Replacing fuse covers When replacing a faulty fuse a 13amp ASTA approved fuse to BS 1362 should always be used and the fuse cover re fitted If the fuse cover is lost the plug must not be used until a replacement is obtained Replacement fuse covers If a replacement fuse cover is fitted it must be of the correct colour as indicated by the coloured marking or the colour that is embossed in words on the base of the plug Changing the plug Removing the plug If your appliance has a non rewireable moulded plug and you should wish to remove it to add a longer cable or to re route the mains cable through partitions units etc please ensure that either The plug is replaced by a fused 13amp re wireable plug bearing the BSI mark of approval or The mains cable is wired directly into a 13amp cable outlet controlled by a switch in compliance with BS 5733 which is accessible without moving the appliance Disposing of the plug Cut off and dispose of the supplied plug if it doe2. Test Piei 235 refrigerator compartment ompr ka Ca P S Low 140 Made in Italy 13918 Never call on unauthorized technicians and always refuse spare parts which are not originals 11 195052765 00 05 2005 Xerox Business Services 12
3. of soda or neutral soap Do not use solvents abrasive products bleach or ammonia e The removable accessories may be soaked in warm water and soap or dishwashing liquid Rinse and dry them carefully e The back of the appliance may collect dust which can be removed by delicately using the hose of a vacuum cleaner set on medium power The appliance must be switched off and the plug must be pulled out before cleaning the appliance Avoiding mould and unpleasant odours e The appliance is manufactured with hygienic materials which are odour free In order to maintain an odour free refrigerator and to prevent the formation of stains food must always be covered or sealed properly e f you want to switch the appliance off for an extended period of time clean the inside and leave the doors open Replacing the light bulb To replace the light bulb in the refrigerator compartment pull out the plug from the electrical socket Follow the instructions below Access the light bulb by removing the cover as indicated in the diagram Replace it with a similar light bulb within the power range indicated on the cover 10W Pur _ A Precautions and tips 1 inbesit The appliance was designed and manufactured in compliance with international safety standards The following warnings are provided for safety reasons and must be read carefully C This appliance complies with the following A Communi
4. Operating Instructions REFRIGERATOR FREEZER COMBINATION Contents jon Installation 2 3 GB Positioning and connection Reversible doors English 1 P i Description of the appliance 4 Overall view Accessories 5 Start up and use 6 7 Starting the appliance Chiller system Using the refrigerator to its full potential Using the freezer to its full potential Maintenance and care 8 Switching the appliance off BAN 134 NF Cleaning the appliance Avoiding mould and unpleasant odours BAN 134 NF G Defrosting the appliance BAN 144 NF Replacing the light bulb BAN 144 NF S Precautions and tips 9 BAN 12 NF General safety Disposal BAN 12 NFS Respecting and conserving the environment Troubleshooting 10 Assistance 11 1 inpesit Installation Before placing your new appliance into operation please read these operating instructions carefully They contain important information for safe use for installation and for care of the appliance Please keep these operating instructions for future reference Pass them on to possible new owners of the appliance Positioning and connection Positioning 1 Place the appliance in a well ventilated humidity free room 2 Do not obstruct the rear fan grills The compressor and condenser give off heat and require good ventilation to operate correctly and save energy 3 Leave a space of at least 10 cm between the top part of the appliance and any furniture abov
5. ages FREEZER OPERATION Knob SHELVESe LAMP see Maintenance MULTI USE bin REFRIGERATOR OPERATION Knob FLEX COOL BOX for MEAT and CHEESE FRUIT and VEGETABLE bin Ice ice trays FREEZER and STORAGE compartment Ice ice traye STORAGE nal compartmente Levelling FEET e Varies by number and or position Available only on certain models Removable lidded shelf with EGG TRAY Removable multipurpose SHELVESe BOTTLE shelf Accessories 1 inbesit SHELVES with or without grill Due to the special guides the shelves are removable and the height is adjustable see diagram allowing easy storage of large containers and food Height can be adjusted without complete removal of the shelf MULTI USE bin to store food such as cold meats for a long time and also prevent odours from lingering in the refrigerator FLEX COOL BOX This is the new box to keep meat fish and cheese fresh When positioned in the lower part of the fridge compartment it is ideal for meat and fish when moved to the top part of the fridge it is perfect for cheese It can be taken out of the fridge when it is not needed PLAY ZONE Thanks to the new Play Zone bottle rack you can cool several bottles cans and energy drinks qu
6. ate freely for food to be preserved properly If circulation is impeded the compressor will work continuously Do not place hot food directly into the refrigerator The internal temperature will increase and force the compressor to work harder and will consume more energy Defrost the appliance if ice forms see Maintenance A thick layer of ice makes cold transference to food products more difficult and results in increased energy consumption Regularly check the door seals and wipe clean to ensure they are free of debris and to prevent cold air from escaping see Maintenance Troubleshooting If the appliance does not work before calling for Assistance see Assistance check for a solution from the following list Malfunctions The internal light does not illuminate The motor does not start The refrigerator and the freezer do not cool well The food inside the refrigerator is beginning to freeze The motor runs continuously The appliance makes a lot of noise Some of the external parts of the refrigerator become hot 10 Possible causes Solutions The plug has not been inserted into the electrical socket or not far enough to make contact or there is no power in the house The appliance comes with a motor protection control see Start up and use The doors do not close properly or the seals are damaged The doors are opened too frequently The TEMPERATURE ADJUSTMENT knob is not in the corre
7. ct position The refrigerator or the freezer have been over filled The TEMPERATURE ADJUSTMENT knob is not in the correct position The door is not closed properly or is continuously opened The outside ambient temperature is very high The appliance has not been installed on a level surface see Installation The appliance has been installed between cabinets that vibrate and make noise The internal refrigerant makes a slight noise even when the compressor is off This is not a defect it is normal These raised temperatures are necessary in order to avoid the formation of condensation on certain parts of the product Assistance i invesit Before calling for Assistance e Check if the malfunction can be solved on your own see Troubleshooting eB e f after all the checks the appliance still does not operate or the problem persists call the nearest Service Centre model serial number Communicating r e type of malfunction A Mod RG 2330 Cod 93139180000 appliance model Mod Tez ish Wl aw le ee ear e serial number S N Total 340 75 Freez Capac Ulass This information can be found on the data Gross Gross Net Gross Poder de Cong clase N y Bruto Bruto Util Bruto kg24h 4 0 Cla plate located on the bottom left side of the Brut Brut Utis Brut orah S atid i Serr R 134a
8. e it and at least 5 cm between the sides and any furniture side walls 4 Ensure the appliance is away from any sources of heat direct sunlight electric stove etc 5 In order to maintain the correct distance between the appliance and the wall behind it fit the spacers supplied in the installation kit following the instructions provided Levelling 1 Install the appliance on a level and rigid floor 2 If the floor is not perfectly horizontal adjust the refrigerator by tightening or loosening the front feet Electrical connections After the appliance has been transported carefully place it vertically and wait at least 3 hours before connecting it to the electricity mains Before inserting the plug into the electrical socket ensure the following e The appliance is earthed and the plug is compliant with the law e The socket can withstand the maximum power of the appliance which is indicated on the data plate located on the bottom left side of the fridge e g 150 W e The voltage must be in the range between the values indicated on the data plate located on the bottom left side e g 220 240V e The socket is compatible with the plug of the appliance If the socket is incompatible with the plug ask an authorised technician to replace it see Assistance Do not use extension cords or multiple sockets Once the appliance has been installed the power supply cable and the electrical socket must be easily accessible
9. e no longer comes into contact with the food placed inside the freezer compartment furthermore the dripping of the water during filling is avoided a lid to cover up the hole after filling with water is also provided a4 i 09 E gt o Pull out the tray by pushing it up Check that the tray is ompletely empty and fill it with water through the opening provided Take care not to exceed the level indicated MAX WATER LEVEL Excess water prevents the ice cubes from dispensing if this happens wait for the ice to melt and empty the tray Turn the tray 90 due to the connected compartments each mould fills with water see diagram Close the opening with the lid provided and put the tray back placing the top part in the corresponding housing and allowing it to drop in again When the ice has formed minimum time approximately 8 hours knock the tray against a hard surface and wet the outside so that the ice cubes come loose and take them out through the opening 13431 HSLYM XV Maintenance and care Switching the appliance off During cleaning and maintenance it is necessary to disconnect the appliance from the electricity supply 1 set the FREEZER OPERATION knob on 2 pull the plug out of the socket Cleaning the appliance e The external and internal parts as well as the rubber seals may be cleaned using a sponge that has been soaked in lukewarm water and bicarbonate
10. ezer into your mouth Do not allow children to tamper with the controls or play with the appliance Under no circumstance should they be allowed to sit on the bins or to hang from the door Keep packaging material out of the reach of children It can become a choking or suffocation hazard Disposal Observe local environmental standards when disposing packaging material for recycling purposes The European Directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment The crossed out wheeled bin symbol on the product reminds you of your obligation that when you dispose of the appliance it must be separately collected Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance Respecting and conserving the environment Install the appliance in a fresh and well ventilated room Ensure that it is protected from direct sunlight and do not place it near heat sources Try to avoid keeping the door open for long periods or opening the door too frequently in order to conserve energy Do not fill the appliance with too much food cold air must circul
11. ickly to have them constantly at hand If the Play Zone is placed on the glass shelf you can store large and medium sized bottles on it simply by laying the bottle on the flat rack This is ideal for storing wine bottles When folded and secured in place on either side of the shelf the rack can be used to store cans at the top energy drinks in the centre and other cans and energy drinks can be rested horizontally on the remaining part of the shelf When placing cans onto the Play zone rack make sure they do not touch the back of the refrigerator interior The Play Zone can be used just like a normal shelf when placed flat and moved up or down along the fridge walls together with the rest of the shelf It can be washed easily and is also dishwasher safe The ideal position for the Play zone rack is the central shelf Available only on certain models GRAFFITI this is the marker kit which makes your Indesit refrigerator more colourful and fun With these markers you can write leave messages and draw on the doors and sides of the refrigerator GRAFFITI is extremely easy and convenient to use after having written or drawn you will be able to easily and quickly erase the drawings using a dry cloth or an ordinary whiteboard eraser Do not use the pen holder to erase the ink This could permanently damage the product and or the parts included in the GRAFFITI kit WARNING the GRAFFITI marker kit wa
12. ng the temperature The temperature inside the refrigerator compartment automatically adjusts itself according to the position of the thermostat knob min warmest max coldest We recommend however a medium position Chiller system No Frost It is recognisable by aeration cells located on the back walls of the compartments The No Frost system circulates cold air continuously to collect humidity and prevent ice and frost formation The system maintains an optimal humidity level in the compartment preserving the original quality of the food preventing the food from sticking together and making defrosting a thing of the past Do not block the aeration cells by placing food or containers in direct contact with the refrigerating back panel Close bottles and wrap food tightly Using the refrigerator to its full potential e Place only cold or lukewarm foods in the compartment not hot foods see Precautions and tips e Remember that cooked foods do not last longer than raw foods e Do not store liquids in open containers They will increase humidity in the refrigerator and cause condensation to form 1 inbesit Using the freezer to its full potential The temperature inside the ECO freezer compartment automatically adjusts itself according to the positi
13. on of Ea the thermostat knob J warmest coldest We recommend however a medium position ECO is the optimal temperature for energy saving levels switches the appliance off including the refrigerator e Do not re freeze food that is defrosting or that has already been defrosted These foods must be cooked and eaten within 24 hours e Fresh food that needs to be frozen must not come into contact with food that has already been defrosted Fresh food must be stored in the top FREEZER and STORAGE compartment where the temperature drops below 18 C and guarantees rapid freezing WARNING to avoid blocking the air circulation inside the freezer compartment it is advisable not to obstruct the ventilation holes with food or containers e Do not place glass bottles which contain liquids and which are corked or hermetically sealed in the freezer because they could break e The maximum quantity of food that may be frozen daily is indicated on the plate containing the technical properties located on the bottom left side of the refrigerator compartment for example Kg 24h 4 Do not open the door during freezing If there is a power cut or malfunction do not open the freezer door This will help maintain the temperature inside the freezer ensuring that foods are conserved for at least 9 14 hours Ice ice tray The fact that they are situated on the top part of the freezer drawers ensures greater cleanliness the ic
14. s not fit your socket The cable should be cut as close as possible to the moulded plug Remove the fuse WARNING To avoid a shock hazard do not insert the discarded plug into a socket anywhere else 1 inbesit Fitting a new plug IMPORTANT WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE Green and Yellow Earth Blue Neutral Brown Live As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in your plug proceed as follows Connect Green and Yellow wire to terminal marked E or or coloured Green and Yellow Connect Brown wire to terminal marked L or coloured red or brown Connect Blue wire to terminal marked N or coloured Black or Blue Ifa 13amp plug BS 1363 is used it must be fitted with a 13amp fuse If you are in any doubt about the electrical supply to your machine consult a qualified electrician before use CE Marking certifies that this appliance conforms to the following EEC directives Low Voltage Equipment 73 23 EEC amp 93 68 EEC Electromagnetic Compatibility 89 336 EEC 92 31 EEC amp 93 68 EEC Reversible doors Description of the appliance op Overall view The instructions contained in this manual are applicable to different model refrigerators The diagrams may not directly represent the appliance purchased For more complex features consult the following p
15. s studied designed and tested to be used exclusively on the doors and sides of those products belonging to the Indesit range with which it is sold Therefore do not use your Graffiti markers on other Indesit refrigerators and or other brands your Graffiti markers on other appliances other types or makes of markers on your Indesit refrigerator If you do not follow the instructions above it could result in colour stains and or permanent marks Children should only use the markers under adult supervision Indesit Company S p A shall not be liable for any effects resulting from incorrect use of the GRAFFITI kit Start up and use Starting the appliance Before starting the appliance follow the installation instructions see Installation Before connecting the appliance clean the compartments and accessories well with lukewarm water and bicarbonate The appliance comes with a motor protection control system which makes the compressor start approximately 8 minutes after being switched on The compressor also starts each time the power supply is cut off whether voluntarily or involuntarily blackout 1 Insert the plug into the socket and ensure that the internal light illuminates the FREEZER OPERATION knob must not be on the position 2 Turn the FREEZER OPERATION knob and REFRIGERATOR OPERATION knob to an average value After a few hours you will be able to put food in the refrigerator Setti
16. ty Directives 73 23 EEC of 19 02 73 Low Voltage and subsequent amendments 89 336 EEC of 03 05 89 Electromagnetic Compatibility and subsequent amendments 2002 96 CE General safety The appliance was designed for domestic use inside the home and is not intended for commercial or industrial use The appliance must be used to store and freeze food products by adults only and according to the instructions in this manual The appliance must not be installed outdoors even in covered areas It is extremely dangerous to leave the appliance exposed to rain and storms Do not touch the appliance with bare feet or with wet or moist hands and feet Do not touch the internal cooling elements this could cause skin abrasions or frost freezer burns When unplugging the appliance always pull the plug from the mains socket do not pull on the cable Before cleaning and maintenance always switch off the appliance and disconnect it from the electrical supply It is not sufficient to set the temperature adjustment knobs on appliance off to eliminate all electrical contact In the case of a malfunction under no circumstances should you attempt to repair the appliance yourself Repairs carried out by inexperienced persons may cause injury or further malfunctioning of the appliance Do not use devices or tools other than the special scraper provided inside the compartments Do not put ice cubes taken directly from the fre
Download Pdf Manuals
Related Search