Home

Brinkmann Kettle Grill Charcoal Grill User Manual

image

Contents

1. LOOK FOR THESE AND OTHER BRINKMANN ACCESSORIES AT YOUR LOCAL RETAILER WHERE SMOKERS ARE SOLD OR ORDER DIRECT BY CALLING 25 1 800 468 5252 2001 The Brinkmann Corporation Dallas Texas 75244 U S A www brinkmanncorp com ONE YEAR LIMITED WARRANTY For one year from date of purchase The Brinkmann Corporation warrants the Brinkmann Gas Stainless Steel Kettle Grill against defects due to workmanship or materials to the original purchaser The Brinkmann Corporation s obligations under this warranty are limited to the following guidelines This warranty does not cover grills that have been altered or damaged due to normal wear rust abuse improper maintenance improper use disassembly of parts and or attempted repair by anyone other than an authorized employee of The Brinkmann Corporation This warranty does not cover ceramic briquets surface scratches rust or heat damage to the finish which is considered normal wear The Brinkmann Corporation may elect to repair or replace damaged units covered by the terms of this warranty This warranty extends to the original purchaser only and is not transferable or assignable to subsequent purchasers The Brinkmann Corporation requires reasonable proof of purchase Therefore we strongly recommend that you retain your sales receipt or invoice To obtain replacement parts for your Brinkmann Gas Stainless Steel Kettle Grill under the terms of this warranty please call Customer Servic
2. BRINKMANN Gas Stainless Steel Grill OWNER S MANUAL ASSEMBLY AND OPERATING INSTRUCTIONS SAVE THIS MANUAL FOR FUTURE REFERENCE NOTICE TO INSTALLER LEAVE THESE INSTRUCTIONS WITH THE GRILL OWNER FOR FUTURE REFERENCE BRINKMany Gas Stainless Stee AWARNING HAZARDOUS EXPLOSION MAY RESULT IF THESE WARNINGS AND INSTRUCTIONS ARE IGNORED READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS IN THIS MANUAL TO AVOID PERSONAL INJURY INCLUDING DEATH OR PROPERTY DAMAGE SE ONLY IMPORTANT SAFETY WARNINGS WE WANT YOU TO ASSEMBLE AND USE YOUR GRILL AS SAFELY AS POSSIBLE THE PURPOSE OF THIS SAFETY ALERT SYMBOL IS TO ATTRACT YOUR ATTENTION TO POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR GRILL WHEN YOU SEE THE SAFETY ALERT SYMBOL PAY CLOSE ATTENTION TO THE INFORMATION WHICH FOLLOWS A READ ALL SAFETY WARNINGS AND INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING AND OPERATING YOUR GRILL A DANGER FOR YOUR SAFETY IF YOU SMELL GAS Shut off gas to the appliance at the LP cylinder and burners Extinguish any open flame Open the Lid If odor continues leave the area and immediately call your gas supplier or your fire department WARNING FOR YOUR SAFETY 1 DO NOT store or use gasoline or other liquids with flammable vapors in the vicinity of this or any other appliance An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance to avoid
3. 8 X 3 8 Sheet metal screws Hood bolts Wing bolts 2 Flat washer 3 8 X 3 8 Sheet metal screws a 8 Wing Bolts Boom M a Choose a good cleared assembly area and get a friend to help you put your grill together Lay cardboard down to protect grill finish and assembly area Step 1 Place kettle grill body upside down as illustrated Step 2 Slide all 3 legs with casters into leg supports Align holes in lower leg with holes in leg supports Do not tighten with 8 X 3 8 sheet metal screws until step 5 18 19 Step 3 Align bottom shelf tank support with holes in the legs Step 4 Insert wing bolts through holes in legs into bottom shelf tank support NOTE When securing wing bolts twist legs for proper alignment with bottom shelf tank support Step 5 Secure legs into leg sockets using three 8 X 3 8 sheet metal screws Ep S X Q SSR p N D O i a BRINMaNy Gas Stainless Steel 7 aui Step 6 With the help of a friend carefully turn the the grill to its upright position Try to minimize stress placed on the legs NOTE Lock casters to prevent grill from moving during final assembly Step 7 Place dome lid on grill body and align hinges Step 8 Fasten hinges together using hood bolts washers and
4. hood nuts as illustrated 20 Step 9 Place heat shield into lower grill body just above burner Step 10 Place cooking grill directly above heat shield Grec oy NNNM Soe aa BRINMANY Gas Stainless Kate Grill x FoR OUTDOOR USE ONE tions in Ashguard grease cup holder Grease cup Step 11 Add control knob to valve by aligning the notched stem of the valve with the cut out on the knob Step 12 Secure handle to lid using screws and washers provided with handle Step 13 To install battery unscrew igniter button cap Insert battery with positive end towards button Replace igniter button cap 0 Step 14 Place grease cup in cut out of ash guard grease cup holder as illustrated Check grease cup periodically when grilling to avoid spills Brinkmann Gas Stainless Steel Kettle Grill Assembled BRINKMANN Gas Stainless Steel call 1 800 527 0717 s cylinder after each Us LP GAS TANK NOT INCLUDED Your grill is covered with a plastic film to protect the stainless steel finish during shipment and assembly This plastic film must be removed before operating your grill ACCESSORIES PROFESSIONAL SHISH KABOB SKEWERS These heavy duty 18 shish kabob skewers are extra long for fabulous restaurant style kabobs Made of rus
5. steam and heat to flow into the food Great for fish shrimp vegetables and hors d oeuvres 812 3333 0 TII Wi Lon COMMERCIAL QUALITY MEAT THERMOMETER An essential tool when cooking all types of meat Get perfectly smoked roasts briskets and turkeys without cutting into the meat Commercial quality thermostat features an easy to read 2 3 4 wide dial with a 5 1 4 stem Features Fahrenheit and Centigrade readings and National Livestock and Meat Board recommended temperatures Also features the newly recommended 170 F internal temperature for fresh pork Stainless steel construction and dishwasher safe 812 4100 0 MEAT TENDERIZING MACHINE The Jaccard Meat Tenderizing Machine s Stainless Steel blades penetrate meat in a single stroke Easy to use with one hand This tenderizer makes any cut of meat unbelievably tender and allows marinade and smoke to penetrate deeply into meat Also reduces cooking time and helps retain flavorful juices Made from ABS plastic with stainless steel blades Completely dishwasher safe Protective cover included 16 BLADE TENDERIZER 812 5016 0 48 BLADE TENDERIZER 812 5048 0 24 ACCESSORIES 2 GALLON PAN amp BASKET SET Restaurant style aluminum fry pan with nickel plated wire straining basket is an essential tool for frying fish chicken french fries onion rings and more Strainer basket holder helps drain excess oil Use outdoors with the Brinkmann St
6. steps 1 through 4 until burner ignites If burner does not ignite using the push button igniter wait 5 minutes see Match Lighting the Burner section MATCH LIGHTING THE BURNER 1 2 Open lid before lighting Turn the burner control knob to OFF Strike and place a long wooden match through the air holes in the bottom LEFT hand side of the grill to approximately 1 2 2 to 3 cm from the burner Turn on the burner control knob to the HIGH position The burner should light within 5 seconds If the burner does not light turn the control knob to OFF and wait 5 minutes for gas to evacuate the grill Repeat steps 1 through 4 until the burner ignites If the burner does not light within the first few attempts of match lighting there is a problem with the gas supply Turn off the gas at the burner and cylinder DO NOT attempt to operate the grill until the problem is found and corrected See Trouble Shooting section of this manual NOTE Observe flame height when lit Flame should be a Blue Yellow color between 1 2 high TURNING OFF THE GRILL 1 Turn OFF the LP tank valve 2 Turn burner control knob to the OFF position NOTE Turn off LP cylinder first to prevent gas from being left in the system under pressure A CAUTION The LP tank valve should always be in the off or closed position when the grill is not in use To turn off the LP tank valve turn knob clockwise until it stops AWARNING OPERA
7. NG WHEN TO PERFORM A LEAK TEST After assembling your grill and before lighting for the first time even if purchased fully assembled Every time the LP gas cylinder is refilled or if any of the gas components are replaced Any time your grill has been moved At least once per year or if your grill has not been used for more than 60 days CHECKING FOR LEAKS Create a mixture of 50 water and 50 liquid dishwashing soap Open the lid Insure the burner knob is set to the OFF position Turn on the fuel supply at the LP cylinder valve Turn the cylinder valve knob one turn counterclockwise Apply the soap water mixture to the following Watch For Bubbles O Supply tank cylinder weld Connection nut to tank valve Back side of connection nut to brass nipple Brass nipple connection into regulator Regulator connections to gas supply hoses Gas supply hose connection to burner valve assembly Burner valve stem cap Burner orifice fitting The full length of gas supply hose Tank valve to cylinder OOGO D OOO 6 Check each place listed A J for growing bubbles which indicates a leak 7 Turn OFF gas supply at cylinder valve 8 Turn on control knob to release gas pressure in hose 9 Turn control knob to off position 10 Tighten any leaking connections 11 Repeat soapy water test until no leaks are detected DO NOT use the grill if leaks cannot be stopped Contact a qualified gas ap
8. TING THE GRILL Never use Charcoal or Lighter Fluid inside your Gas Grill Read and follow all warnings and instructions contained in the preceding sections of this manual BREAKING IN YOUR GRILL n manufacturing and preserving the components of your grill oil residue may be present on the burner and cooking surfaces of your grill e Before cooking on your grill for the first time you should operate it for 15 minutes on HIGH to burn off these residual oils PREHEATING THE GRILL e Prior to use it is recommended that you preheat your grill This ensures that the grilling surfaces are at the desired temperatures to sear the food sugars when cooking After lighting your grill set the burner control knob to the HIGH position for 10 to 15 minutes 10 CONTROLLING FLARE UPS Flare ups are a part of cooking meats on a gas grill This adds to the unique flavor of cooking on a gas grill Excessive flare ups can over cook your food and cause a dangerous situation for you or your grill Excessive flare ups result from the build up of grease in the bottom of your grill If this should occur DO NOT pour water onto the flames This can cause the grease to splatter and could result in serious burns or bodily harm When grease fires occur close the lid and turn off the burner until the grease burns out Use caution when opening the lid as sudden flare ups may occur AWARNING DO NOT leave your grill unattended while in use DO NOT move
9. a out of direct sunlight e If storing the grill outdoors cover the grill with a grill cover for protection from the weather A grill cover can be purchased by contacting The Brinkmann Corporation at 1 800 527 0717 CLEANING AND MAINTENANCE For safe grilling and peak performance of your grill perform these checks at least twice per year or after extended periods of storage HARDWARE Be sure to tighten up all hardware nuts bolts screws etc at least twice per year 12 BURNER AND VENTURI Although your burner is constructed of cast iron it will rust as a result of the extreme heat and acids from cooking foods Regularly inspect the burner for cracks abnormal holes and other signs of corro sion damage If found replace the burner e Venturi tube can become blocked by spiders and other insects building their nests Blocked venturi tubes can prevent gas flow to the burner and could possibly result in a venturi fire To clean the venturi remove the ash guard grease cup holder plate from between the legs Then remove the three retaining bolts from the bottom of the burner and remove the burner from the grill Use a pipe cleaner or a small wire and insert into the opening of the venturi Remove any obstructions that may exist Replace the burner ash guard grease cup holder plate and follow the Gas Leak Testing section of this manual COOKING GRILLS Clean with mild soap detergent and water A brass bristled brus
10. ainless Steel Gas Kettle Grill and avoid the mess and odor of frying indoors 815 3610 0 THE ULTIMATE 5 PIECE BBQ TOOL SET You ll be the envy of your fellow outdoor chefs with this ultimate BBQ tool set It s sleek ergonomic i e design combined with durable heavy gauge stainless steel construction is truly impressive Extra wide polished utensils provide precise handling and control when flipping basting and turning your food on the grill Beautifully crafted smooth rosewood handles are oval shaped to fit comfortably in your hand and are extra long to keep your hands safely away from the j fire The five piece set includes tongs spatula fork basting brush and a grill brush Includes diviii 4 t d X x MULTI PURPOSE SPATULA If you could have only one BBQ tool this multi purpose spatula is it Aside from being a great spatula it features a serrated edge for cutting a bottle opener and special grooved edges for cleaning grills Made of heavy gauge stainless steel to last for years Beautiful rosewood handles are slotted and riveted for maximum strength and durability Includes leather hanging straps for convenient storage 812 5047 0 SMOKE N SPICE SEASONING These custom blended spices are a delicious marinade seasoning for smoke cooking and leather hanging straps for convenient storage Y y Y yO 812 5045 0 grilling Contains no MSG Available in red and white meat varieties i
11. d beyond 80 capacity Over filled tanks can create a dangerous condition Over filled tanks can build up pressure and cause the relief valve to expel propane gas vapors The vapor is combustible and if it comes in contact with a spark source or flame an explosion causing severe burns bodily harm or death could occur Always use a protective cylinder cap when grill is not connected to cylinder If you exchange a cylinder with a qualified exchange program be sure the cylinder has a Type 1 valve and an over filling prevention device OPD INSTALLING THE LP GAS CYLINDER ONTO THE GRILL 1 Check that the cylinder valve is closed by turning the knob clockwise 2 Place the cylinder onto the bottom shelf tank support 3 Orient the cylinder such that the valve opening does not kink or damage the supply hose HOSE AND REGULATOR Your grill is equipped with a Type 1 connection device with the following features 1 The system will not allow gas flow from the cylinder until a positive connection to the valve has been made NOTE The cylinder valve must be turned off before any connection is made or removed 2 Athermal device that will shut off the gas flow if the device is subject to temperatures above 240 F and 300 F 115 C and 150 C If this should happen remove the entire regulator assembly and throw it away A replacement regulator assembly can be purchased by contacting Brinkmann at 1 800 527 0717 The ca
12. e Department at 1 800 527 0717 A receipt will be required The Brinkmann Corporation will not be responsible for any grills forwarded to us without prior authorization Brinkmann Gas Stainless Steel Kettle Grill must be returned to the original place of purchase for replacement of the unit EXCEPT AS ABOVE STATED THE BRINKMANN CORPORATION MAKES NO OTHER EXPRESS WARRANTY THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF PURCHASE SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU ANY LIABILITY FOR INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE FAILURE OF THE BRINKMANN GAS STAINLESS STEEL KETTLE GRILLTO COMPLY WITH THIS WARRANTY OR ANY IMPLIED WARRANTY IS EXCLUDED CUSTOMER ACKNOWLEDGES THAT THE PURCHASE PRICE CHARGED IS BASED UPON THE LIMITATIONS CONTAINED IN THE WARRANTY SET OUT ABOVE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Owner s Manual for Models 11 01 2 02 810 3300 0 140 3300 0
13. grill for anything other than its intended purpose DO NOT use while under the influence of drugs or alcohol Grill is hot when in use To avoid burns DO NOT attempt to move the grill Lock the wheels so the unit does not accidentally move Wear protective gloves or oven mitts DO NOT touch any hot grill surfaces DO NOT wear loose clothing or allow hair to come in contact with grill USE CAUTION AND COMMON SENSE WHEN OPERATING YOUR GAS GRILL FAILURE TO ADHERE TO THE SAFETY WARNINGS AND GUIDELINES IN THIS MANUAL COULD RESULT IN SEVERE BODILY INJURY OR PROPERTY DAMAGE SAVE THIS MANUAL FOR FUTURE REFERENCE AWARNING FOR OUTDOOR USE ONLY DO NOT operate indoors or in an enclosed area such as garage shed or breezeway Use your grill OUTDOORS in a well ventilated space away from dwellings or other buildings to prevent dangers associated with gas accumulation and toxic vapors We recommend your grill be situated at least 10 feet from buildings Maintain a minimum clearance of 24 inches 60 cm between all sides of grill and walls or other combustible material DO NOT install in or on a recreational vehicle and or boat INSTALLATION INFORMATION The installation of this appliance must be in accordance with All applicable local codes or in the absence of local codes either National Fuel Gas Code e ANSI Z223 1 1988 or latest edition USA Natural Gas Installation Code CAN CGA B149 1 Canada e Propane Installatio
14. grill when in use Lock wheels in place to stabilize grill DO NOT use water to extinguish flare ups Have fire extinguisher readily accessible suitable for use with gas appliances TO MINIMIZE FLARE UPS e Trim excess fat from meats prior to cooking e Cook meats with high fat contents chicken or pork on Low settings or indirectly Ensure that your grill is on level ground and the grease is allowed to evacuate the grill through the drain hole in the bottom AWARNING DO NOT store a spare LP gas cylinder filled or empty under or near the grill Never store flammable liquids or spray canisters under or near the grill DO NOT extinguish grease fires using water 11 AWARNING TRANSPORTING AND STORAGE Never move a grill when it is hot or when objects are on the cooking surfaces Make sure that cylinder valve is shut off After moving the grill check that all gas connections are free of leaks Check the venturi tubes to ensure they are properly connected to the valves and the orifices are inside the venturi tube Follow the instructions listed below BEFORE STORING YOUR GRILL Ensure that the fuel supply tank valve is fully closed Clean all surfaces Lightly coat the burner with cooking oil to prevent excess rusting e If storing the grill indoors disconnect the LP tank and leave the LP tank OUTDOORS Place a protective cap cover on the LP tank and store the tank outdoors in a well ventilated are
15. h or a nylon cleaning pad can be used to remove residue from the chrome plated cooking surface Do not use steel wire bristles to clean the chrome plated cooking grill Steel can cause the chrome plating to chip or crack DO NOT use a commercial oven cleaner HEAT SHIELD e Periodically it may be necessary to inspect and clean the heat shield to prevent excess grease build up When the grill is cold remove the cooking grill Inspect the heat shield and replace if broken or damaged Do not allow heat shield to become damaged to the extent that it may fall through onto the burner Replace the heat shield and cooking grill and light the burner Operate the grill on HIGH for 10 minutes to remove the excess grease TROUBLE SHOOTING Problem e Burner will not light Fire at control knob Yellow Flames at burner Flame blows out on LOW e Burner does not get hot enough e Grill is Too Hot m 9 gud co Possible Causes Check LP cylinder fuel level Bad electrode spark Check to see if the grill will match light Electrode or collector may need adjustment Venturi may not be properly seated Venturi may be obstructed The cylinder valve may be closed Regulator is not properly seated on cylinder valve Venturi is obstructed See section on Cleaning and Maintenance of the Venturi Venturi is improperly seated on control valve Gas connections may be loose Leak Check and tighten all connectio
16. he interior surface can be buffed cleaned then lightly coated with vegetable oil or vegetable oil spray to minimize rusting GRILL COOKING TIPS CLEANLINESS Always wash hands thoroughly with soap and hot water prior to handling food and after handling raw meat un cooked poultry or seafood When using a platter to carry raw meat un cooked poultry or seafood to the grill make sure to wash the platter thoroughly with soap and hot water before placing cooked foods back on the platter or use different platters for raw and cooked foods Never use the same utensils when handling raw meat un cooked poultry or seafood unless you wash the utensils thoroughly with soap and hot water Never re use marinade from raw meat or un cooked poultry on foods that have been cooked and are ready to be served GRILLING TO PROPER TEMPERATURE Use a meat thermometer to be sure food has reached a safe internal temperature You may order a Commercial quality thermometer from Brinkmann For more information on this product and other Brinkmann accessories please refer to the accessory pages at the end of this manual The US Department of Agriculture recommends the minimum temperature be reached for the following food items Chops ios seen oben See See 145 degrees F Ground Meat 160 degrees F Pork e TIAE 160 degrees F Poultry cere 180 degrees F Roasts 145 degrees F HELPFUL HINTS 15 If you pre cook meat or poul
17. n Code CAN CGA B149 2 Canada To check your local codes see your local LP gas dealer or natural gas company This grill was not intended to be connected to a natural gas supply line AWARNING LP GAS CYLINDER NOT SUPPLIED WITH THIS GRILL The LP Liquid Propane gas cylinder specifically designed to be used with this grill must have a 20 Ib 9 1 kg capacity incorporating a Type 1 cylinder valve and an over filling protection device OPD DO NOT connect this grill to an existing 510 POL cylinder valve with Left Hand threads The Type 1 valve can be identified with the large external threads on the valve outlet DO NOT connect to a propane cylinder exceeding this capacity DO NOT connect to a cylinder that uses any other type of valve connection device CYLINDER SPECIFICATIONS When purchasing or exchanging a cylinder for your gas grill it must be constructed and marked in accordance with the specifications for LP gas cylinders of the U S Department of Transportation DOT or the National Standard of Canada CAN CSA B339 as applicable with a listed over filling prevention device OPD The cylinder must also be equipped with A shut off valve terminating in a Type 1 gas cylinder valve outlet e AType 1 valve that prevents gas flow until a positive seal is obtained An arrangement for vapor withdrawal Acollar to protect the cylinder shut off valve e A safety relief device having direct communication with the vapo
18. n a money saving 2 pack 812 3322 0 STAINLESS STEEL WOOD CHIP SMOKING BOX Rugged stainless steel smoking box allows wood chips to burn longer for richer smoke flavor and provides easy cleanup of ashes Ideal for charcoal electric gas smokers CERAMIC BRIQUETS Disperses heat evenly and vaporizes drippings for delicious barbecue flavor and grills T WEN N 168 7006 0 812 3311 0 me uc a ER ELECTRONIC COOKING THERMOMETER amp TIMER Eliminate guesswork and cook with precision in your oven grill or smoker MARINADE INJECTOR Ts This electronic digital thermometer amp timer ensures that your food will be cooked to perfection by pre setting cooking time and temperature The alarm sounds automatically when the food is done The stainless steel probe that is connected to 3 feet of wire provides an instant digital readout of internal cooking temperature of food without removing the grill lid or opening the oven door Includes double magnet on the electronic unit for attachment to metal surfaces Includes a AAA battery 812 5030 0 This quick and easy marinade injector marinates meat in 5 minutes not hours Mix your favorite marinade and spices into a liquid and inject into turkey roast m chicken or steak for a naturally tenderized and flavorful delight The reusable Marinade Injector includes a heavy duty stainless steel needle and heavy gauge plastic syringe to last for years 812 5059 0
19. ns Venturi is obstructed See section on Cleaning and Maintenance of the Venturi Venturi may be obstructed See section on Cleaning and Maintenance of the Venturi Grill is not sufficiently preheated Venturi is improperly seated on control valve Flow control device has been activated in regulator Turn off the grill and the fuel supply Disconnect the grill from the cylinder valve Reconnect the grill to the cylinder and light grill See section on Connection to the LP Cylinder Excess grease build up causing grease fires Damaged or faulty regulator Replace with factory authorized parts Cook on a lower temperature setting 14 PROPER CARE amp MAINTENANCE To protect your grill from excessive rust the unit must be kept clean and covered at all times when not in use A grill cover may be ordered directly from Brinkmann by calling 1 800 468 5252 or 1 800 527 0717 Wash cooking grill and heat shield with hot soapy water rinse well and dry Lightly coat cooking grill with vegetable oil or vegetable oil spray Clean inside and outside of grill by wiping off with a damp cloth Apply a light coat of vegetable oil or vegetable oil spray to the interior surface to prevent rusting If rust appears on the exterior surface of your grill clean and buff the affected area with steel wool or fine grit emery cloth Touch up with a good quality high temperature resistant paint Never apply paint to the interior surface Rust spots on t
20. pliance repair service 12 Turn OFF gas supply at cylinder valve until you are ready to use your grill 13 Wash off soapy residue with cold water and towel dry 14 Wait 5 minutes to allow all gas to evacuate the area before lighting grill NOTE The leak test must be performed in an area that has adequate lighting in order to see if bubbles are developing DO NOT use a flashlight to check for bubbles AWARNING PRE START CHECK LIST Property damage bodily harm severe burns and death could result from failure to follow these safety steps These steps should be performed after the grill has been assembled stored moved cleaned or repaired DO NOT operate this grill until you have read and understand ALL of the warnings and instructions in this manual e Insure that the grill is properly assembled e Check burner venturi tube for blockage from insect nests See section on Cleaning and Maintenance e Check that burner venturi are seated properly over the valve outlet as shown in the assembly instructions The orifice must be inside the burner venturi for proper air fuel mixing Inspect the gas supply hose for burns chaffing kinks and proper routing before each use Hoses should be at least 3 inches from hot surfaces e Leak check all gas connections and hoses See section on Leak Testing Ensure that all electrical supply cords are properly grounded and are kept away from water and hot surfaces e Position your g
21. r space of the cylinder e Alisted over filling prevention device OPD AWARNING Turn off the cylinder valve when your grill is not in use Handle the tank with care Always secure the cylinder in an upright position Never connect an unregulated LP gas cylinder to your grill DO NOT expose LP gas cylinders to excessive heat or ignition sources DO NOT store a spare LP gas cylinder under or near your grill Allow only qualified LP gas dealers to fill or repair your LP gas cylinder DO NOT allow the cylinder to be filled beyond 80 capacity Read and follow all warnings and instructions that are on the cylinder and that accompany this product A DANGER Never store a spare LP gas cylinder under or near your grill This could cause excess pressure to be expelled through the vapor relief valve resulting in fire explosion or severe personal injury including death NOTE PROPANE GAS IS HEAVIER THAN AIR AND WILL COLLECT IN LOW AREAS PROPER VENTILATION IS EXTREMELY IMPORTANT DO NOT insert any foreign objects into the valve outlet Damage to the back check could result A damaged back check can cause a leak possibly resulting in explosion fire severe bodily harm or death AWARNING FILLING THE LP GAS CYLINDER Allow only qualified LP gas dealers to properly fill or repair your LP gas cylinder New tanks should be purged prior to filling inform LP gas dealer if you are using a new tank DO NOT allow the cylinder to be fille
22. rill on level ground in a well ventilated location a safe distance from combustible materials and buildings e Properly place an empty grease collection cup under the grease drain hole in the bottom of the grill to catch grease during use e Your grill is covered with a plastic film to protect the stainless steel finish during shipment and assembly This plastic film must be removed before operating your grill AWARNING Read understand and follow all warnings and instructions contained in this manual DO NOT skip any of the warnings and instructions contained in the preceding sections of this manual AWARNING LIGHTING INSTRUCTIONS Follow the instructions exactly OPEN THE GRILL LID before attempting to light the burner so that fumes do not accumulate inside the grill An explosion could occur if grill lid is down Check that burner control knob and the cylinder valve are turned to the OFF position Turn on the fuel supply by rotating the cylinder valve knob counterclockwise to full open DO NOT stand with head body or arms over the grill when lighting LIGHTING THE BURNER 1 2 Open lid before lighting Uess Steel Turn on the burner by pressing in and rotating the Y R Ze y control knob to the HIGH position Press and hold the igniter button until the burner ignites If burner does not ignite immediately turn the burner control knob to OFF and wait 5 minutes for gas to evacuate the grill imes Iren Repeat
23. structions and warnings on the supply hose safety tags Read and follow all warnings in this manual concerning the safe use of LP gas cylinders and the hose and regulator before connecting cylinder to grill Read and follow all warnings on the LP cylinder 1 Check that the cylinder valve is closed by turning the knob clockwise 2 Check that the grill s burner knob is in the proper OFF position 3 Remove the protective plastic cap from the cylinder valve and the connection device 4 Insert the nipple of connection device into the valve outlet Insure that the device is centered properly 5 Turn the large coupling nut clockwise by hand and tighten to a full stop Take care not to cross thread the coupling nut onto the cylinder valve Do not over tighten the knob onto the valve Do not use tools to tighten connection NOTE If you are unable to make the connection repeat steps 4 and 5 6 Check that the hose does not contain kinks does not contact sharp edges and does not contact surfaces that may become hot during use 7 Leak check all fittings before lighting your grill See section on Leak Testing in this manual A DANGER LEAK TESTING To prevent fire or explosion hazard DO NOT smoke or permit ignition sources in the area while conducting a leak test Perform test OUTDOORS only in a well ventilated area Never perform a leak test with a match or open flame Never perform a leak test while the grill is in use AWARNI
24. t resistant stainless RIB RACK Chrome plated rack can greatly increase the cooking capacity of your grill Holds ribs chicken halves potatoes and corn vertically to triple cooking capacity Allows smoke steam and heat to penetrate food evenly 600 0062 3 n Yeu Ns UK Y WU M 1 og U Hg M j MEATLOAF BASKET The unique basket weave prevents meatloaf from falling through the grill while allowing smoke steam and heat to flow into the food Also provides a convenient method for lifting your meatloaf in and out of the smoker 400 0073 0 CHICKEN AND TURKEY RACKS These chromed steel racks hold chicken cornish hen duck or turkey upright and are ideal for smoking grilling or oven roasting poultry The rack allows the meat to cook from the inside as well as from the outside This speeds up cooking time seals in flavor ful juices and promotes even browning of skin It s a low fat way to cook poultry because excess fat drips off the meat When oven roasting place poultry on rack in a shallow pan of water to steam baste to tender perfection When grilling or smoking simply place poultry on rack atop the grill Makes carving easier too CHICKEN RACKS SET OF TWO 885 9015 0 TURKEY RACK 885 9025 0 steel to last for years SET OF 12 812 2904 0 SMOKER BASKET The unique basket weave prevents food from falling through the grill while allowing smoke
25. the possibility of explosion A WARNING Never store a spare LP gas cylinder under or near this grill Never fill the cylinder beyond 80 full A fire causing death or serious injury may occur if the above is not followed exactly 4 WARNING Never use natural gas in a unit designed for liquid propane gas Never use charcoal briquets or lighter fluid in a gas grill Leak test all connections before first use even if grill was purchased fully assembled and after each tank refill Never check for leaks using a match or open flame CAUTION Strong odors colds sinus congestion etc may prevent the detection of propane Use caution and common sense when testing for leaks Always keep gasoline paint thinner or other flammable liquids or combustible materials away from your gas grill Always check the grill prior to each use as indicated in the Pre Start Check List section of this manual Keep children and pets away from hot grill DO NOT allow children to use or play near this grill DO NOT leave the grill unattended while in use DO NOT allow the gas hose to come in contact with hot surfaces DO NOT allow grease from drain hole to fall on hose or valve regulator assembly Keep any electrical supply cords away from water or heated surfaces Keep a fire extinguisher on hand acceptable for use with gas products Refer to your local authority to determine proper size and type For household use only DO NOT use this
26. try do so immediately before grilling Never defrost meat at room temperature or on a countertop Refrigerate leftovers within 2 hours of taking food off the grill For additional information please phone the USDA s toll free Meat amp Poultry Hotline at 1 800 535 4555 ASSEMBLY INSTRUCTIONS A READ ALL SAFETY WARNINGS amp ASSEMBLY INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR OPERATING YOUR GRILL WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT The following tools are required to assemble this Brinkmann Stainless Steel Gas Kettle Grill Pliers Phillips amp Flathead Screwdrivers Adjustable Wrench PARTS LIST D 1 Kettle Grill Body 5 3 Legs with casters 2 1 Dome lid 1 Cooking grill 20 5 dia 9 1 Heat shield 1 Grease cup 1 Bottom shelf Tank support 9 1 Control knob S 1 Handle with bolts and washers Your grill is covered with a plastic film to protect the stainless steel finish during shipment and assembly This plastic film must be removed before operating your grill FOR MISSING PARTS PLEASE CALL CUSTOMER SERVICE AT 1 800 527 0717 Proof of purchase will be required Inspect contents of the box to ensure all parts are included and undamaged 16 PARTS BAG CONTENTS Make sure you have all items listed under PARTS LIST and PARTS BAG CONTENTS before you begin the installation process Your Parts Bag will include PARTS BAG CONTAINS 2 2 3 2 3 17 Hood Nuts Flat washers
27. use of the excessive heat should be determined and corrected before using your grill again 3 A flow limiting device when activated restricts the flow of gas to 10 cubic feet per hour AWARNING Never use your grill without leak testing all gas connections and hoses See the section on Leak Testing in this manual for proper procedures AWARNING The pressure regulator and hose assembly supplied with your gas grill is designed to work with an LP gas supply cylinder DO NOT attempt to connect it to any other fuel supply source such as a natural gas line DO NOT use any other pressure regulator hose assembly other than the one supplied with your grill DO NOT attempt to adjust or repair the regulator A replacement regulator can be supplied by contacting the manufacturer The regulator is designed to operate at an output pressure of 11 inches of water column 2 74 kPa During assembly and or replacement of the gas cylinder keep the gas supply hose free of kinks and or damage Visually inspect the hose assembly prior to each use for evidence of damage excess wear or deterioration If found replace the assembly before using your grill Only the manufacturers supplied replacement should be used AWARNING CONNECTING HOSE AND REGULATOR TO AN LP GAS CYLINDER Insure the tank valve is CLOSED prior to connecting the LP gas cylinder to your grill Turn the valve knob clockwise to properly close the valve Read and follow all in

Download Pdf Manuals

image

Related Search

Related Contents

Handbuch Polaphor HD    Philips Stick 929689644402  1 - MacroSystem Digital Video AG  Manual - Lowrance  Supermicro 1012C-MRF  ハードウェア取扱説明書 - アラクサラネットワークス株式会社  ATW-A49 取扱説明書  manual on M-Tx - Werner Icking Music Archive  GE Bolt Mike III Operating Manual  

Copyright © All rights reserved.
Failed to retrieve file