Home

Brick Computer CB-101A Security Camera User Manual

1. Brickcom EasyLink EasyLink is a unique Brickcom function which allows users to assign a unique domain name to their network camera s IP address There is no need to configure the router to open up ports or remember hard to memorize IP addresses When this function is enabled users can log onto uniquedomainname mybrickcom com to view the camera s web GUI and live view 1 Check the box to enable EasyLink 2 Enter a unique domain name whose length must be between 5 32 characters Verify that the domain name is available 3 Select a desired amount of time from the Refresh Time drop down menu to confirm the connection status 002602 7fc3c4 mybrickcom com EasyLink Status The EasyLink function cannot work because the IP camera is located behind a Double NAT network Click Apply to apply settings or Cancel to cancel changes A NOTE The EasyLink function will not work if the following conditions occur 1 The camera cannot be located behind a double NAT network 2 The camera s IP address cannot be assigned to specific port numbers using the router s port forwarding 3 EasyLink uses UPnP to exchange port information with the router The camera must connect to the internet through a router which supports UPnP 45 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Wireless These settings control how a Network Camera interacts with a wireless network Users can identify the wireless network and ena
2. c l the connection was successful the user will see the message Congratulations The installation of the camera is complete When this window is displayed click lt PC NVR gt to start the PC NVR program lt Live View gt to view the live video from the connected IP camera or lt X gt in the top right corner of the screen to close the installation window To run the PC NVR program please refer to the PC NVR user manual for more information Once installation is complete the Administrator should proceed to the next section Accessing the Network Camera for necessary changes and configurations 97 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Accessing the Network Camera Check Network Settings The camera can be connected either before or immediately after the software installation The Administrator should complete the network settings on the configuration page including entering the correct subnet mask and IP address of gateway and DNS Ask the network administrator or Internet service provider for the detail information Add Password to Prevent Unauthorized Access The Administrator should immediately implement a new password as a matter of prudent security practice For first time use the user name and password for the Administrator are assigned as admin admin After the Administrator changes the Administrator password the web browser will display an authentication window to confirm the new password
3. for 5 second s Current status Open The DO socket allows the IP camera to send output to an external device While executing the DO notification action the IP camera drives voltage on the connected DO wire to the triggering voltage level for X number of seconds The connected external device will then be triggered for X number of seconds Triggered Voltage Level OPEN or GROUND Users should select the option according to the specification of their external device A NOTE This function is only available for CB 101A and CB 102A models Video Clip Video Clip Post Alarm Buffer Seconds 0 30 1024 Jones 120 1500 This function is used to determine when video clips will be recorded and stored after an event is triggered Pre alarm buffer Images can be stored internally on the server from the time immediately preceding the trigger Enter the desired length of time Post alarm buffer Images can be stored internally on the server from the time immediately following the trigger Enter the desired length of time Maximum buffer size Specify the maximum file size allowed Click Apply to apply settings or Cancel to cancel changes 66 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Audio Clip Audio Recording Audio clips can be recording and played when an event occurs Audio Recording Audio Clip List Please selectafiletoimport Browse Audio Recording Settings maron 5 Mi secon
4. Press Button to Reboot Apply This feature will reboot the camera Click Apply to begin A message will pop up asking The device will reboot Are you sure Click OK to continue The camera will take about one minute to reboot Microsoft Internet Explorer The device will reboot Are you sure The following message will show during the rebooting process jama pesa jamoa ieee her ii om RN A RS AS Please wait a moment When completed the live video page will be displayed in the web browser 78 BRICKCOM COM BLOCK UP YOUR SECURITY
5. This Agreement permits you to use one copy of the specified version of the Software for internal purpose only on only one computer and only by one user at atime If you have purchased multiple licenses for the Software then at any time you may have as many copies of the Software in use as you have licenses If you obtain the Software together with a hardware product you are allowed to use the Software as a part of the hardware according to this Agreement The Software is in use on a computer when it is loaded into the temporary memory i e RAM or installed into the permanent memory e g hard disk CD ROM or other storage device of that computer In the event BRICKCOM provides you the upgrade for the Software you may use the resulting upgraded Software only in accordance with the terms of this Agreement Y accept the terms of the licen greemen Print 13 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom 4 Select either Complete setup or Custom setup to install the system a If COMPLETE SETUP is selected All program features will be installed into the default directory Check the option Complete and then click lt Next gt Brnckcom Solbrare Kit Installshield Wizard Setup Type Select the setup type to install Please select a setup type All program features will be installed Requires the most disk space Y Custom Select which program features you want installed Recommended for a
6. Next gt to continue Please read the following text Current Settings Setup Type Custorn Select Features EasyConfig PC NVR Standard Choose Destination Location EasyConfig C Program FilesiBrickcomiEasyConfig PC NVR Standard C Program FilesiBrickcormPC NWR StandardiExe Creating shortcuts EasyConfig Create Desktop Shortcut Create Quick Launch Shortcut Create StartMenu Shortcut PC NVR Standard 17 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom 5 To launch EasyConfig or PC NVR Standard select the application and click lt Finish gt When launching the PC NVR program please refer to the PC NVR user manual Brickcom Software Kit InstallShield Wizard Installation Complete Thank you for choosing Brickcorn Ed Co you wantto launch the application right now PC NVR Standard Finish 18 BRICKCOM COM BLOCK UP YOUR SECURITY EasyConfig To launch EasyConfig select EasyConfig from the start menu If Complete Setup type was used in the software installation an EasyConfig icon was installed on the desktop Double click to open the icon Easvicontig lf Custom Setup type was used in the software installation and an EasyConfig icon was not installed on the desktop the program will be installed under C Program Files Brickcom EasyConfig unless the program was saved to a preferred directory 1 Click lt Start gt to continue The program will automatically search for th
7. Once the password is set there is no provision to recover the Administrator s password If the Administrator s password is lost the only option is to restore the original factory default settings The Administrator can set up a maximum of ten 10 user accounts Users will be able to access the Network Camera but will not be allowed to access system configurations 28 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Authentication To access the camera s live view open a web browser and enter the IP address of the camera A dialog window will pop requesting a username and password As stated on the previous page for the default username and password for the Administrator are assigned as admin admin For accounts other than the administrator s account the user can choose to remember the password for future convenience Itis not recommended to check this box when viewing the camera feed from a public computer Connect to 197 168 1 1 The server 192 168 1 1 at Brickcom IPC4M Login requires a Username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection User name E admin e Remember my password 29 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Installing the Plug In For the initial access to the camera in Windows the web browser may prompt the administrator for permission to install a
8. PC AT Compatible CPU Pentium 3GHz or faster Memory 1024 MB or more Monitor 1024 x 768 pixels or more 24 bit True color or better Network Interface 10 100Mbps Network interface card must be installed Web Browser Microsoft Internet Explorer 6 0 SP2 or higher Adobe Reader Adobe Reader 8 0 or higher Audio The audio function will not work if a sound card is not installed in the PC Audio may be interrupted depending on network traffic 8 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Camera Connection lt CB 100A gt 1 Connect the supplied power cable from the camera to the power outlet 2 Connect the camera to a switch via Ethernet cable lt CB 101A CB 102A gt 1 Ground 2 Digital Input 3 Digital Output 4 Power 5V 3 Terminal I O Connector Block Connection 3 1 The supplied terminal I O connector block can be used to connect external devices such as sensors and alarms to the camera Use the diagram above to attach the external devices to the connector block Attach the connector block to the terminal BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom connector on the camera 2 Basic Connection Without PoE 2 1 Connect the camera to a switch using a standard Ethernet cable 2 2 Connect the power adapter from the camera to a power outlet A note DC12V 1A power adapter is required 3 Power over Ethernet PoE Connection 3 1 The CB 101A is PoE compliant so there are two opti
9. connection for SSID TBrickcom is down Thu Jan 1 03 16 56 2009 LOG _WARNING VWireless Wireless connection for SSID Brickcom is down Thu Jan 1 03 17 21 2009 LOG NOTICE WebServer User admin logged in to web server Thu Jan 1 03 16 39 2009 LOG NOTICE WebServer User admin logged in to web server Thu Jan 1 03 24 41 2009 LOG NOTICE WebServer User admin logged in to web server Thu Jan 1 03 24 46 2009 LOG WARNING VWireless Wireless connection for SSID TBrickcom is down Thu Jan 1 03 36 20 2009 LOG WARNING VWVireless Wireless connection for SSID TBrickcom is down Thu Jan 1 03 36 46 2009 LOG NOTICE WebServer User admin logged in to web server Thu Jan 1 03 42 10 2009 LOG IlNF stream Channel 1 started streaming to host 169 254 209 1987 Thu Jan 1 03 42 20 2009 LOG _INFO Wireless Wireless connection for SSID Brickcomf is up Thu Jan 1 04 20 37 2009 LOG WARNING VWireless Wireless connection for SSID Brickcomy is down Thu Jan 1 04 31 08 2009 LOS INFO stream Channel 1 started streaming to host 169 254 209 1987 Thu Jan 1 04 31 52 2009 LOG INF stream Channel 1 stopped streaming to host 169 254 209 198 Thu Jan 1 04 33 06 2009 LOG_INFO stream Channel 1 stopped streaming to host 169 254 209 198 Thu Jan 1 04 35 54 2009 This page displays the system s log in chronological order The system log is stored in the camera s buffer area and will be overwritten when the buffer area is full Click Retrieve to retrieve the
10. fia A ka S P PoE Switch py E q Small Office q Monitor FE Surveillance Elderly and Residence a Child Care Monitor e e BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Device Appearance Description lt Front amp Rear view gt lt CB 100A CB 101 A gt lt CB 102A gt Adjustable Focal Lens Built in 2 Microphone PIR Illumination LED gt gt Speaker Ethernet RJ45 Da 1 10 100 Socket 4 Terminal I O Connector Reset Button H Reset Button Power Connector 4 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom lt Side view gt HS Micro SD slot gt Power LED Status LED WPS button Internet LED WCB 100A Only TT gt WPS LED WCB 100A Privacy button Firmware upgrade LED CB 100A CB 101A CB 102A Privacy LED A NOTE The WPS and Privacy buttons must first be enabled through the web GUI in order to work See page 41 for details on how to enable the Privacy button 1 These are optional features Please refer to the Product List for the full list of optional features available for the product 5 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom LED Behavior ee mM JS Continuous Illumination Normal Operation Powered off 1 Connected to switch by Continuous Illumination Ethernet or WiFi 2 Reset to default se 1 Powered off 2 No connection 1 Upgrading FAN f a scond 2 Performing
11. images to an FTP server Samba Email or HTTP FTP Settings File Transfer Protocol FTP is used as an application component to automatically transfer files for program internal functions Select Primary FTP Server from the Server Selection drop down menu to send media files to a FTP server when an event is triggered Enter the FTP IP address or hostname By default the FTP port server is setto 21 Enter the account name password and FTP Path to configure the settings FTP Settings Pasion o TETO TE eme e emp ne Click Apply to apply settings or Cancel to cancel changes 62 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom E mail Settings select Primary Email Server option from the Server Selection drop down menu to send media files to an email server when an event is triggered SMTP Server Enter the server host name of the email server SMTP Port Enter the port number of the email server by default the SMTP port is set to 25 Authentication Select the authentication type from the drop down menu Email Account Enter the user name of the email account if necessary Email Password Enter the password of the email account if necessary Email Settings swe semer Email Account Te Click Apply to apply settings or Cancel to cancel changes 63 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Samba Settings Select this option to send the media files via a network neighborhood w
12. new plug in for on Internet Explorer Permission request depends on the Internet security settings of the user s PC or notebook If the highest security level is set the computer may prohibit any installation and execution attempt This plug in has been registered for certificate and is used to display the video in the browser Click on o ntal to proceed If the web browser does not allow the administrator to continue the installation check the Internet security option and lower the security levels or contact the networking supervisor or IT for help internet Explorer Security Warning Do you want to install this software Name Brickcom cab Publisher BRICKCOM CORPORATION y More options Install Don t Install While Files From the Internet can be useful this file type can potentially harm your computer Only install software from publishers you trust What s the risk Anote If an error occurred or the plug in fails to install it is because the version of the Electronic Signature is newly released and the VeriSign has not been submitted to Microsoft Windows update for validation Therefore plug in will not have its root certificate If IE discovers that there is no root certificate after the user s PC connects to the camera It will automatically redirect to VeriSign Web site to download and install the latest root certificate to make the installation successfully If the user s computer is able to con
13. or Cancel to cancel changes 39 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Multicast Multicast sends a video stream to the multicast group address and allows multiple clients to acquire the stream at the same time by requesting a copy from the multicast group address Therefore multicast can effectively save Internet bandwidth The RTSP Real Time Streaming Protocol controls the delivery of streaming media Click Enable to enable Multicast stream 1 or Multicast stream 2 The default value for multicast address and port are 234 1 2 3 and 10000 Use different port number for different streams It is recommended to use the default values A NOTE Using the IP address of the Network Camera enables access to the video Example rtsp 192 168 1 1 channel1 Click Apply to apply settings or Cancel to cancel changes 40 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Privacy Mask Control The Cube camera is equipped with a privacy feature which allows users to disable the video recording when it is not needed This application is particularly useful when the camera is being used for home surveillance With the privacy button the user can have privacy while they are going about their daily life Privacy Mask Control Privacy Mask Control Hardware Privacy Mask Button Privacy Mask Control Enable the Privacy Mask control to remotely disable live view and recording from the camera Hardware Privacy M
14. site survey 1 Connecting to the network Second Blue 2 Restoring settings Continuous lllumination Connected to Internet Third Blue 1 Powered off Third Blue 2 No connection Firmware i inati Firmware successfully CB 100A CB 1 Upgrade upgraded 01A CB 102A Fourth Blue WCB 100A Fourth Blue WPS in progress WCB 100A Fourth Blue WPS Connection Error 6 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Hardware Reset WL Reset Button The Reset Button can be used to reboot the camera or restore it to factory default settings If the camera experiences a problem rebooting the camera may correct the problem If the problem remains please restore the camera to factory default settings and reinstall the software To Reboot Press and hold the Reset Button for one second using a paper clip or thin object Wait for the camera to reboot To Restore Press and hold the Reset Button for ten seconds until the LED light turns off When successful restored the LED will be blue during normal operation note By restoring the camera all settings will be restored to the factory default settings Micro SD SDHC Card Capacity The network camera is compatible with Micro SD SDHC Maximum 32GB cards se BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Installation System Requirements Operating System Microsoft Windows XP Home Edition SP2 Microsoft Windows XP Professional SP2 Computer IBM
15. Brickcom Megapixel PoE Cube Network Camera CB 100A CB 101A CB 102A Series Users Manual Quality Service Group Brickcom Product name Release Date Manual Revision Web site Email Network Camera CB 100A CB 101A CB 102A series 2010 11 V1 0 www brickcom com technical brickcom com info brickcom com 2010 Brickcom Corporation All Rights Reserved BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Table of Contents Berore VOU Use ThS Product cessisse AR MDA MERO RR EAR RA eee 0 me Oa cl dal aan meee a a mee Ree te Meier cite Or eter Merete Ren cette ROE re errr ee 0 Regulatory INTOFMALON sessir on aE E E EEE ERE E a E E E ESERSE E iE 1 ele o A A o A 0 Cube Network Camera OVerviOW occcooccccccncconnccocnconcnccnnnconononnnnnonnnnonnnonnnnnonnnnonnnnnnnnnnnens 1 DEVICE Appearance DescripthON enori nir ran rarna da o ni nd end 4 PED Ts MNO a 6 e nen nee ten tnr nt hast Meet Ch trae a 8 Oy Sle tlh te CDN MINN ie es es Cannes O nu GAR RAND DER ND DEDE RAD E staealaceannalaeg 8 Camera OLA CLO assa code 9 SOME ale IVS Tall eal Ola a 12 A eerie oe ere ie rite A ere ere ae 19 Accessing the Network Came ra cccccccccssscccsssceceeececeeeeeseeseeseueeeseeeesseesesseeesseeeesaeees 28 Check NetWork Sellada ii 28 Add Password to Prevent Unauthorized ACCESS eee 28 A Pea Pager Paes Pec ro Pee 29 ASIAN ls serto A O a ei 30 LIVE VC o a a A a a a e Poee tea 31 34 Gam
16. E a higher bitrate will use higher network bandwidth The video quality can be set between Level 1 to Level 6 with Level 6 producing the best image quality HTTP Transport If MJPEG is used for Video Codec users can enable HTTP Transport protocol for video communication A NOTE HTTP Transport is for non lE browser used only Click Apply to apply settings or Cancel to cancel changes Video Overlay Stream Video Overlay RTSP Server Save File Folder Timestamp me Text o 0 o The video overlay will only take effect in stream 1 Timestamp To display the date and time on the screen during live view check Enable to enable the timestamp function and select the display position from the drop down menu Text To make a note about the camera check Enable and select the display position from the drop down menu Enter a video description in the text box Click Apply to apply settings or Cancel to cancel changes A NOTE The video overlay will only takes effect in stream 1 37 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom RTSP Server Stream Video Overlay RTSP Server Save File Folder RTSP Server Ae To utilize RTSP authentication the user must first set a password for the camera RISP Real Time Streaming Protocol controls the delivery of streaming media By default the port number is set to 554 Authentication Depending on the network security requirements the camera provides two t
17. Full Screen Cancel Brightness Drag the slider bar to adjust the image brightness level from 5 to 5 Contrast Drag the slider bar to adjust the image contrast level from 5 to 5 Sharpness Drag the slider bar to adjust the image sharpness level from 5 to 5 Saturation Drag the slider bar to adjust the image saturation level from 5 to 5 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Exposure Control Sport Select this option when monitoring rapid moving objects Normal Select this option for normal monitoring conditions Night Vision Select this option when monitoring at night or in low light conditions User Defined Select this option to define the exposure manually AGC Auto Gain Control The AGC can be set between 1X to 5X Set the Gain Rate higher for a better video illumination with 5X giving the best video illumination A NOTE higher gain rate may cause a higher judder or blur on fast moving images Shutter Speed Fast For high activity exposure function Normal For normal exposure function Slow For night vision exposure function AE Lock Auto Exposure The camera will automatically adjust the exposure to the changes in ambient light De Noise Auto The camera will automatically filter the frame to frame defects to reduce the visual impact of blur The De noise can be set between 1 to 3 with 3 giving the best video resolution Mirror and Flip Mirror Enable to horizonta
18. SECURITY Brickcom b If Recurrence Pattern is selected the following page will be displayed Event Settings Event List 12345 Motion Detection send to Email O Always Schedule Event Schedule Recurrence Pattern Sun 4 Mon CJ Tue 4 Wed 4 Thu O Fri O sat O start 00 or Duration 10 minutes Audio Detection O Save Stream to LJ Send Snapshot to E Play Audio Clip There is no available audio clip Configure one here C Send HTTP Notification LJ Send to Email LED Light C Send UDP Notification to IP address PLL IE frol C Send Multicast Notification to IP address Fort An event schedule can be programmed to recur at different times according to the user s needs Select the days for the event schedule to occur Select a start time and specify the duration 3 Define what will trigger an event to occur by selecting an option from the Event drop down list 4 Select the Actions that will occur when the event is triggered 57 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom a When lt Send to Email gt is selected the following page will be shown Dim Always Event Schedule Schedule O Recurrence Pattern Motion Detection C Save Stream to C Send Snapshotto F Play Audio Clip There is no available audio clip Configure one here C activate Digital Output C send HTTP Notification C LED Light F send UDP Notification to IP address LIL Il Tl Jero d send Mult
19. TTP This unicast method can be used to traverse firewalls Firewalls are commonly configured to allow the HTTP protocol thus allowing RTP to be tunneled 31 BLOCK UP YOUR SECURITY Brickcom TCP This protocol guarantees the complete delivery of streaming data and provides better video quality The downside of using this protocol is that the quality of its real time effect is less than that of the UDP protocol UDP This protocol allows for more real time audio and video streams However network packets may be lost due to network burst traffic and images may be broken Activate UDP connection time sensitive responses are more important than video quality LED Control Use the drop down menu to adjust the brightness of the camera s LED Recording on off Displays the status of recording video speaker on off Displays the status of the Speaker aje MIC on off Displays the status of the MIC volume MD on off Displays the status of Motion Detection e Brightness Drag the slider bar to adjust the image brightness level e Mic volume Drag the slider bar to adjust the microphone volume e Speaker volume The built in speaker will play sound from an audio clip from the computer microphone when it is enabled For more Audio settings please refer to the Audio configuration page pm Playor Stop Play or stop the video on Recording Record video to a computer Snapshot Capture and save still im
20. The IP Filter is used to filter the IP addresses which are able to access the network camera Enable the IP Filter and select to allow or deny a range of IP addresses access to the server Click Add to list to add the IP range to the IP filter list 4 Enable IP Filter Allow Access List Deny Access List Click Apply to apply settings or Cancel to cancel changes 76 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Firmware Upgrade This feature allows the user to upgrade the camera firmware It will take a few minutes to complete the process A NOTE Do not power off the camera or camera during the upgrade Upgrade Click Browse and specify the firmware file Click Upgrade The camera will begin upgrading and will reboot automatically when the upgrade is finished Firmware Upgrade Setare Bone Ure Configuration This feature allows the user to export import the configuration files of the network camera Import Export Click export to pop up a dialog to indicate the location and file to export Click browse to indicate the location and file of the camera configuration and click import to import the configuration file back into the network camera Please selecta fletoimport Browse 77 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Reset to Default Click Apply to restore the network camera to factory default setting Reset to Default Press Button to Reset Apply Reboot
21. ages Eo Digital Zoom Enable the digital zoom operation 32 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom EM Mirror Horizontally reflect the display of the live video mg Flip Vertically reflect the display of the live video M Real Size View the object in real size Press it again to switch back to normal mode E Full Screen Switch to full screen mode Press the Esc key to return to normal J i Mute Turn off the sound re Talk To communicate through the camera using the computer MIC Set Default Reset to default settings A NOTE 1 The lt Camera Control Panel gt functions have no effect on the recorded video Whatever changes are made to the lt Camera Control Panel gt will not be applied to the recorded video 2 The LED is not for continuous use and has an estimated life span of 30 000 hours 3 The LED cannot be replaced 33 gt BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Configuration Click lt Configuration gt on the main page to change the camera settings pages A NOTE Only Administrators can access the Configuration page Camera Video Audio Camera Exposure Control O Sport Normal O Night Vision O User Defined De Noise Level 1 Acceptable Mirror and Flip C Mirror O Flip Flicker Free Outdoor Mode Indoor Mode 50Hz Indoor Mode 60Hz Color Effect Color Black amp White Test in
22. alled Requires the most disk space Select which program features you want installed Recommended for advanced users Cancel 15 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom iii Select the features to install Click lt Next gt to continue Brickcom Software Kit InstallShield Wizard Select Features Select the features setup will install Description EasyConfig will help user easily configure the Brickcom IP camera Space Requiredon C Space Available on C Cancel iv Click lt Change gt to change the appointed folder where installation and program files will be stored Click lt Next gt to continue Sisto Dm fuso Vs DIM ALU Y SIT ait SIL DLL EAA DULL a At InstallShield Wizard Choose Destination Location Select folder where setup will install files Ca Install Brickcom Software Kit to CiProgram FilesiBrickcorn Change Cancel 16 BRICKCOM COM BLOCK UP YOUR SECURITY rickcom v Select programs to create shortcuts Click lt Next gt to continue lt Brickcom Software Kit InstallShield Wizard Setup Type Select the setup type that best suits your needs The InstallShield Wizard has successfully installed Brickcom Software Kit Click Next to continue M Create Desktop Shortcut M Create Quick Launch Shortcut Ed Create StartMenu Shortcut vi The installation information will be displayed Click lt
23. anagement ia 73 EE DAIRO Co Sana 74 Manten aC aaa 75 veer INIAIN ACTIN CIN serte ice 75 El A qm anata baratanteates 76 Edo ic eee o RR Rc SR 76 EALE 67 fe o c RIR mere ORE ates ET RR eee ene ne oe ree 77 CONQUER teecetee tree erenece cre ceer ce ters neetesar rt cerr cect es nent caer a rennet TT PIC SC OHO CANN iai in rd dd ida 78 PP a ps oe see ese ee 78 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Before You Use This Product In many countries there are laws prohibiting or restricting the use of surveillance devices This Network Camera is a high performance web ready camera which can be part of a flexible surveillance system It is the user s responsibility to ensure that the operation of this camera is legal before installing this unit for its intended use Upon opening the products package verify that all the accessories listed on the Package Contents are included Before installing the Network Camera read the warnings in the Quick Installation Guide to avoid misuse When installing the Network Camera carefully read and follow the instructions in the Installation chapters to avoid damages due to faulty assembly or installation FCC Warning This device complies with Part 15 of FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may C
24. ask Button Click to enable the privacy mask button on the camera If this feature is not enabled the user will not be able to use the privacy mask button 41 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Network IP Settings This section explains how to configure a wired network connection for the camera There are several ways to setup the camera over the Internet 1 obtain an available dynamic IP address assigned by a DHCP server 2 use a static IP or use PPPoE Point to point over Ethernet Select the desire setup mode from the IP settings drop down menu IP Settings 1 DHCP lf this option is selected the camera will automatically obtain an available dynamic IP address from the DHCP server each time it connects to the LAN IP Settings subnet Mask 255 255 o o HEHE 2 Static IP Select this option to manually assign a static IP address to the camera Enter the static IP address Subnet mask Default Gateway Primary and Secondary DNS provided by the ISP 42 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom IP Settings 3 PPPoE Point to point over Ethernet Use this mode if connecting to the Internet through a DSL Line A NOTE To utilize this feature it requires an account provided by an Internet Service Provider Enter the user name and password provided by the ISP Click Apply to apply settings or Cancel to cancel changes UPnP Universal Plug and P
25. ause undesired operations BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Regulatory Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment This device complies with Part 15 of the FCC Rules Operation is subject to
26. ble wireless encryption A NOTE This function is only available for WCB models Basic Settings Basic Settings Advanced Settings Wi Fi Protected Setup Cancel WPA2 Personal Site Survey List Click the Site Survey Button to update the list Network Name SSID The Service Set Identifier SSID is the network name used to identify the wireless signal emitted from a wireless camera It is case sensitive and can be up to 32 characters long Wireless devices have a default SSID set by the factory Brickcom wireless products use Brickcom as the default name It is recommended for users to rename their SSID to something unique in order to distinguish their wireless device from surrounding wireless networks A NOTE Be careful when including personal information when naming the SSID as it is viewable by anyone browsing for wireless networks 46 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Security Encryption protects data transmitted over a wireless network Wi Fi Protected Access WPA Personal WPA2 personal and Wired Equivalent Privacy WEP offer different levels of security for wireless communication A network encrypted with WPA Personal WPA2 personal is more secure than a network encrypted with WEP because WPA Personal WPA2 personal uses dynamic key encryption To protect the information as it passes through the airwaves it is recommended to enable the highest level of encryption supported
27. by the network equipment Site Survey Survey the local area for available wireless networks The user should select their Local Area Network LAN from the Site Survey List Basic Settings Advanced Settings Wi Fi Protected Setup Site Survey List test gary_Brickcom_1 1bigin NONE ae Infrastructure SmantHub AWwRT 600M 1bigin NONE NC NS Infrastructure gt Iil Test FAE 11bg n NONE EE 100 Infrastructure Dim BNO TECGT 44 hi alm ELI Iafraetrinetiora Enlart l lt 47 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom WEP Wired Equivalent Privacy WEP is a basic encryption method which transmits network broadcast messages using radio signals It is not as secure as WPA Basic Settings Advanced Settings Wi Fi Protected Setup Security 40 64 bits 10 hex digits Y 5 ERES RR 00 DR NN Site Survey List a test_gary_Brickcom_1 11b0 n NONE Infrastructure LJ SmanltHub AVWWRT600N 11b g n NONE Infrastructure Test FAE 11b g n NONE 100 Infrastructure Dr IVO TEST 44hi adn A aan i a r Bont Imfractrictora Salar a Tx Key Select a key from the drop down menu WEP Encryption Select a level of WEP encryption 64 bits 10 hex digits or 128 bits 26 hex digits The default is 64 bits 10 hex digits Key 1 4 Enter the WEP key s manually Authentication The default is set to Open System which allows either Shared Key or Auto authentication to be used With Shared Key authentication the sender and re
28. c event rules Triggering voltage Level LOW or HIGH Users should select the option according to the capability of their external device A NOTE This function is only available for CB 101A and CB 102A models 60 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom PIR The PIR Passive InfraRed sensor measures infrared light radiating from objects in its field of view This can be used to detect a moving object such as a person in dimly lit areas sensitivity Adjust the sensitivity of the PIR Sensor from the drop down menu The sensitivity can be set from 10 100 with the default sensitivity set at 50 Higher sensitivity levels will increase the range of the PIR Sensor When the sensitivity level is set to 100 the PIR sensor will be able to detect moving objects within six meters Audio Detection Audio Detection Users can schedule an event to be triggered if there is a change in the sound level of a monitored area Audio detection can be used to measure change in the ambient voice Select the sensitivity from the drop down menu Sensitivity is used to adjust the sensitivity of the sound level from 10 100 The default sensitivity is 50 Click Apply to apply settings or Cancel to cancel changes 61 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Notifications Use the tools in this section to specify what type of notification will be sent when an event occurs The camera can send buffered
29. cipient use a WEP key for authentication With Auto authentication the sender and the recipient do not use a WEP key for authentication Click Apply to apply settings or Cancel to cancel changes 48 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom WPA Personal WiFi Protected Access WPA Personal Basic Settings Advanced Settings Wi Fi Protected Setup Henor Name 550 Brckcon Ste sunoy Apply Site Survey List SmanltHub AVWRT600M 11bg n NONE e Infrastructure MA Tos Gir AND TECT AdAhiain RISiRIE Imfroactriictiire Loy is Encryption Supports two encryption methods with dynamic encryption keys Temporal Key Integrity Protocol TKIP and Advanced Encryption Standard AES Select the algorithm type from the drop down menu TKIP or AES The default is TKIP Shared Key Enter the key shared between the Router and the server keys Enter a password of 8 63 characters Click Apply to apply settings or Cancel to cancel changes 49 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom WPA2 Persona I WiFi Protected Access WPA2 Personal Basic Settings Advanced Settings Wi Fi Protected Setup Network Name 5510 Brickcom Dema S Site Survey List A test_gary_Brickcom_1 11bg n NONE Sc 3 1 bricom 3 1 bigin NONE Infrastructure Test Cavin 11big NONE ot Tm Infrastructure BORE al Intfrartructira Salar Dr MUDO Tee T dA dkhiaim BLRC F Encryption WPA2 supports AES encry
30. d Click Browse to import a file from a local hard drive or network disk Select the file and click Import A NOTE The camera can only play audio clips which are saved as wav files with G 711 u law encoding in 8000 Hz sampling rate To record a new clip using the camera s microphone 1 File Name Enter a file name 2 Duration Enter the number of seconds to record 3 Click Record to record the new audio clip 4 The new audio clip will appear on the audio clip list 5 Select an audio clip file from the Audio Clip List a Play Select to hear the audio clip b Stop Select to stop playing the audio clip c Delete Select to delete an audio clip d Export Select to export the audio clip to a local hard drive or network disk 67 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom LED Light LED Light LED Light Keep active during event Keep active for 0 sec activate inactivate Mode Select Keep active during event or Keep active for a specific amount of time when an event is triggered LED Control The LED on the front of the camera can be set to flash at a configurable interval when an event is triggered From the Activate drop down menu select a percentage which the LED will brighten to When the LED reaches the selected percentage it can be configure to fade to off or turn off Select the option from the Inactive menu Click Apply to apply settings or Cancel to cancel chan
31. dvanced LIZEIS JF te ein ok Cancel E ii Select to create shortcuts Click lt Next gt to continue Brickcom Soitware Kit Installshield Wizard Setup Type Selectthe setup type that best suits your needs The InstallShield Wizard has successfully installed Brickcom Software Kit Click Next to continue J Create Desktop Shortcut J Create Quick Launch Shortcut Create StartMenu Shortcut 14 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom iii The installation information will be displayed Click lt Next gt to continue ckcom Software Kit InstallShield Wizard Please read the following text Current Settings Setup Type Complete Select Features EasyConfig PC NWR Standard Choose Destination Location EasyConfig C Program FilesiBrickcomiEasyConfig PC NWR Standard C Program FilesiBrickcomiPC NVR StandardiExe Creating shortcuts EasyConfig Create Desktop Shortcut Create Quick Launch Shortcut Create StartMenu Shortcut PC NWR Standard b If CUSTOM SETUP is selected i This option is recommended for advanced users It can be used to install the system to a preferred directory or to select specific program feature s li Check the option Custom and then click lt Next gt BricEcom Software Kit Installshield Wizard Setup Type Selectthe setup type to install Please select a setup type Y Complete All program features will be inst
32. e camera in the intranet A NOTE Check Skip the hardware installation guide to skip checking the hardware connection To check the hardware installation settings do not check the option box Brickcom Welcome Thank you for choosing Brickcorn EasyConfig will help you easily configure your Brickcorn IP camera Skip the hardware installation guide select Language English 2010 Brickcom Corporation All rights reserved 19 BLOCK UP YOUR SECURITY Brickcom Connection NETWORK CABL Brickcom CAMERA ETHERNET PORT Plug one end of the supplied network cable into your network switch or router Plug the other end of the supplied network cable into the camera s Ethernet port 20 BLOCK UP YOUR SECURITY Brickcom Plug the power adapter into the camera s power port Then connect the other end into the power outlet Please check that the LED light is on CAMERA PES ETHERNET PORT Edge POWER U E Select either Simple Mode or Professional Mode to obtain the camera s IP settings If Simple Mode is selected EasyConfig will set up the connection automatically If Professional Mode is selected the user will need to configure the IP settings manually Brickcom If simple mode is selected the easy configuration program will set up the connection automatically lf professional mode is selected the user will need to configure the IP manually The DHCP sett
33. era s IP address There is no need to configure the router to open up ports or remember hard to memorize IP addresses Users can log onto uniqueEasyLinkname mybrickcom com to view the camera s web GUI and live view 1 Enter a unique EasyLink name whose length must be between 5 32 characters 2 When finished click the arrow button to continue A norte See page 44 for more details about the EasyLink function 25 BRICKCOM COM BLOCK UP YOUR SECURITY 7 When the IP address settings have been configured the screen will either display a successful or failed connection message If the connection failed either try again or quit the installation a If DHCP IP address settings was selected the failure page will be displayed as below Brickcom Sorry cannot connect el IPECamera PO 1304p has no response please check 1 f your router has DHCP server supported 2 set computer IP address to 192 166 1 100 and subnet mask to 255 255 255 0 if your computer connects to the IP camera directly Please try again or click Finish to quit the installation ENS SI b If Static IP address settings was selected the failure page will be displayed as below Brickcom Sorry cannot connect WI me ra IF CamerafFO 1304p has no response the following settings are recommended IP Address 192 168 2 195 Please try again or click Finish to quit the installation ro Y 26 BLOCK UP YOUR SECURITY Brickcom
34. es can be expensive and difficult to install and maintain With the EasyConfig software the PoE Cube series can easily be installed and configured by anyone without extensive technical knowledge The video can be reviewed remotely so business owners can monitor office safety and employee productivity at all times Residence monitor Home owners worry about their house and property when they are away The PoE Cube series has a built in PIR sensor which can detect unauthorized movement in a residence Once movement is detected the illumination LED will be triggered and an alert with a snapshot can be emailed or sent through an MMS to the user s portable device Elderly and Child Care A high concern for many people is the safety of elderly relatives and small children Users can use the PoE Cube series to ensure the safety of their loved ones by use of the live view and intercom functions E The motion detection feature can be used to create forbidden areas in the home which Pet Monitor the pet should not enter when the owner is away If the camera records the pet entering the region a recorded message can be programmed ito play and the owner will be notified via email or MMS ee BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom E Terminal Block DI DO 3G Network gt gt ae eia mao NBIPC with oo 7 web Browser 1 E r i A E ae A o e a ai
35. etaMdso AUD arre 34 Onn ee STEE E OR see ee AEE AT eee eee E ren 34 VIIE Oend nada RR DR REAR DRA NR A 36 POO Seem nen es ae ae eee eee a ee SR RE 39 NGIU CA res reece cinco cineca ee eects nse ne 40 FIV ACY Mask CONTO renn n o e a a a ee 41 NEONO a e aa a 42 He GRU e AA Re RR e RNP lt 42 Ul oe ae ee ee a eer A 43 DDNS dynamic domain name service errar 44 EEE RO A A 45 Missa eet a a A 46 HTTP HTTP Seres renan esrrao ao rorovo vero A AR 53 SA O 55 Event Settings coooocccocncccocnnicncnnccnancnonanononoooo n O 55 Motion DetectioN cooocooocoonccononononoconacononoononoooooo i ace 59 Digital Input DI oocoocconccncnanincnononcccaconanocanccnaconarono oc O 60 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom AAA A RR O ceed eect 61 A og B 21 CUON apa RS RR a Pere Paar Meee RR Sa Porc Pra eee oe 61 NO HIIG ALI OWNS triana 62 PR SONO Ss ee eter neater Pore tee Pere A ere eer ee see 62 A RG Raso san asEs A cus Reto Ras Raton Capa Rc Res ans Es als 63 Samba SOLOS sa ence mt en mera ten eee ane DS eee en eran ener Renee E 64 A An teeter ae terete ee tener eer eee er treet renee eter ee etree nent 65 Digital Output DO crap ita di noite ond bd ond eden enti 66 O spect RE O se ee a see E A 66 AU O ONE 67 LEDER eso Ro Res ue RAD O RD 1 CAD TER ADS TE a cate 68 OVO LO 0 ae ee A ree eee E 69 By US TU II RR RR wees ees ee ate 69 Dale ano IMM 71 DEVICE IMA ra 72 storage M
36. f Service feature that improves quality for audio video and voice applications by prioritizing wireless traffic To use this feature the wireless client devices on the network must support Wireless WMM The default setting is Enabled To disable this feature select Disable Click Apply to apply settings or Cancel to cancel changes 51 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Wi Fi Protected Setup Basic Settings Advanced Settings Wi Fi Protected Setup Wi Fi Protected Setup Enter PIN number 38989827 in the AP device Enter the AP s SSID Brickcom Click the Register button on the rightto start wPs Register Hardware WPS Button Use this method if the client device has a Wi Fi Protected Setup PIN number 1 Enter the network name from the device in the field 2 Click lt Register gt to start WPS 3 Click Enable to enable the WPS Button If this feature is not enabled the user will not be able to use the WPS button Click Apply to apply settings or Cancel to cancel changes 52 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom HTTP HTTPS HATTP HTTPS Cancel HTTP HyperText Transfer Protocol This protocol allows for TCP protocol quality without having to open specific ports for streaming Users inside a firewall can utilize this protocol to allow streaming data through HTTPS Hypertext Transfer Protocol over SSL This protocol allows authentication and encrypted communication
37. ges 68 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom System System Log Log Set up the camera to record a system log when an event is triggered System Log Remote Logging LOG WARNING VVireless Wireless connection for SSID TBrickcom is down Thu Jan 1 00 00 12 2009 LOG NOTICE WebServer User admin logged in to web server Thu Jan 1 00 02 35 2009 LOG NOTICE WebServer User admin logged in to web server Thu Jan 1 00 02 52 2009 LOG INFO stream Channel 1 started streaming to host 169 254 209 1987 Thu Jan 1 00 02 55 2009 LOG_INFO stream Channel 1 stopped streaming to host 169 254 209 198 Thu Jan 1 00 09 07 2009 LOG INFO stream Channel 1 started streaming to host 169 254 204 198 Thu Jan 1 00 09 18 2009 LOG INFO stream Channel 1 stopped streaming to host 169 254 209 198 Thu Jan 1 00 09 58 2009 LOG_INFO Wireless Wireless connection for SSID TBrickcom is up Thu Jan 1 01 44 31 2009 LOS WARMINGAMreless Wireless connection for SSID TBrickcom is down Thu Jan 1 02 44 18 2009 LOG_NOTICE WebSerer User Tadmin logged in to web server Thu Jan 1 02 48 40 2009 LOG_INFO stream Channel 1 started streaming to host 169 254 204 198 Thu Jan 1 02 48 48 2009 LOG INFO stream Channel 1 stopped streaming to host 169 254 209 198 Thu Jan 1 02 52 02 2009 LOG_WARNING Wireless Connection to wireless module was lost Internal module is either down or not responding Thu Jan 1 03 16 50 2009 LOG WARNING VWireless Wireless
38. he motion detection windows The user can defined up to three areas on the live view window for motion detection 1 2 Select lt Win1 gt lt Win2 gt or lt Win3 gt to adjust the motion detection window Check the box to enable the window Use the mouse to resize or move the motion detection window Adjust the Sensitivity level Lower sensitivity levels will result in more activity needed to trigger an event Adjust the Threshold to change the threshold level The higher the threshold the larger objects need to be to trigger an event 59 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom 6 The chart below the Live View window indicates the activity level of the Motion Detection window When motion is detected by the camera and exceeds the defined threshold a red bar will appear Users can use this feature as a trigger source to send photos or videos to a remote server via email or FTP Click Apply to apply settings or Cancel to cancel changes Digital Input DI Digital Input Camera will trigger the actions when the DI status is Low Current status High The DI socket allows the IP camera to receive input from an external device The external device should have the ability to drive voltage on the connected DI wire to the triggering voltage level in order to notify the IP camera of any event of interest The IP camera will then process the event notification according to the specifi
39. hen an event is triggered Server Address Enter the IP address of the Samba server User Name Enter the user name of the Samba server Password Enter the password of the Samba server WorkGroup Enter the workgroup of the Samba server Shared Folder Enter the share folder of the Samba server Samba Settings O E mms Shared Folder Default Click Apply to apply settings or Cancel to cancel changes 64 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom HTTP Settings select this option to send the media files via an HTTP notification when an event is triggered HTTP Settings URL Specify the URL to send HTTP requests The URL is normally written as http ip address notification cgi parameter jp address type the IP address or host name of the HTTP host Parameter type the notification parameter if necessary Example URL http 192 168 1 1 xxxx cgi Message name1 valuel amp nameZ vlaueZ Result http 192 168 1 1 xxxx cgi name1 value1 amp name2 viaue2 Ex https 192 168 1 1 notification cgi event MD amp camera FB 100A Message Enter the message notification that will be sent when an event is triggered Enter the user name and password if necessary Click Apply to apply settings or Cancel to cancel changes 65 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Digital Output DO Digital Output When the DO is triggered the DO status will be changed to Grounded
40. his function LED Indicators LED Indicators Configuration Click Apply to apply settings or Cancel to cancel changes 74 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Maintenance User Management This section explains how to enable password protection and create multiple accounts User Management User Management index O Username Administrator Add The administrator account name is admin which is permanent and cannot be deleted Click Add to create an account User Management User Management icicle Doo o TO di ig Po do Privilege Viewer e Enter the new user s name password and confirm password Administrators can add up to 10 user accounts Select the privilege level for the new user account from the drop down list Privilege levels can be assigned as 75 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Administrator user has access to view and change the Configuration page Users with administrator privilege can change other user s access rights and delete user accounts Click Delete or Update to delete or modify a user s account Viewer user can only access the main page for live viewing Remote Viewer user can only access the main page for live viewing using TCP protocol Language Language Apply Cancel select the desired language from the drop down menu Click Apply to apply settings or Cancel to cancel changes IP Filter
41. icast Notification to IF address Email From Enter the email address of the sender li To Enter the email address of the recipient To enter multiple recipients separate each using a comma iii Senders Name Enter the senders name that will appear in the recipient s inbox iv Subject Enter the title of the email 5 When complete click Apply to save new event or Cancel to delete the event The new event will appear on the event list 6 To edit an event setting select the event from the list To remove an event setting from the list select an event name from the list and then click lt Delete Event gt Click lt Add Event gt to add more events A norte Refer to the Audio Clip section for more details about the Play Audio Clip action 58 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Motion Detection Motion can be detected by measuring changes in the speed or vector of an object or objects in the monitored area This section explains how to configure the Network Camera to enable motion detection Region Settings Sensitivity Threshold Use the mouse to resize or move the Motion Detection Window This chart records the amount of activity within the Motion Detection Window When the activity level is above the threshold the user will be notified The MD setting is only activate in stream 1 MET Cancel Detection Setting Use this setting to enable and define t
42. ing is recommended If userants to set the IP address manually please refer to the product user manual Simple Mode y Professional Mode 21 BLOCK UP YOUR SECURITY 3 There may be many cameras in the local network Differentiate the cameras using their UPnP name Double click on the camera from the survey list to connect Brickcom Please double click the camera you want to connect from the list UPnP Name IP Address MAC Address Model Name 1 3 4 2 T 5 q Search again FB 1004 dabe 192 166 100 21 00 26 82 Lbida b2 FB 1004p FO 1004p 000d 192 168 100 12 00 26 82 1a 00 0d FO 1004p FO 1004p FFd9 192 166 100 11 00 26 82 19 FF d9 FO 1004p FB 1004 e dbc7 192 168 100 20 00 26 82 1bidbic FB 10046 FO 1004p 3456 192 166 100 10 00 00 00 12 34 56 FO 1004p FB 1004p dads 192 165 100 22 00 26 582 1b da d8 FB 1004p WEB 1004e dc31 192 160 100 24 00 26 82 1bide 31 WPFE 1004e FB 1004p db5 192 168 100 23 O00 26 82 1bidb 54 FB 1004p WEFB 1004p 0035 10 542 201 00 0 5 00 00 35 WFB 1004p 4 Enter the username and password of the camera For first time use the default username and password are admin admin Fem Please enter the Username and password of the camera a o 929 BLOCK UP YOUR SECURITY 5 For configuring the IP address settings select either lt Settings remain the same gt lt Automatically obtain an IP Address DHCP gt or lt Set IP Address configuration man
43. lay UPnP simplifies the process of adding a camera to a local area network Once connected to a LAN the camera will automatically appear on the intranet Click Enable to enable this function and enter an UPnP name which the camera will appear under on the intranet UPnP Name CB 10e Click Apply to apply settings or Cancel to cancel changes 43 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom DDNS dynamic domain name service DDNS links a domain name to an IP address allowing users to easily access their camera even with a changing IP address Brickcom network cameras are compatible with two DDNS service providers 1 DynDNS and 2 TZO A norte Before utilizing this function please apply for a dynamic domain account from a DDNS provider DynDNS Enable the DynDNS to allow the camera to have a fixed host and domain name Refer to the DynDNS website www dyndns com to apply for a dynamic domain account When an account has been created enter the username password and hostname Click Apply to apply settings or Cancel to cancel changes TZO NA Cem mine TZO is a DDNS provider which allows users to create a dynamic DNS Refer to the TZO website http www tzo com to apply for a dynamic domain account When an account has been created enter the e mail address password and domain name Click Apply to apply settings or Cancel to cancel changes 44 BRICKCOM COM BLOCK UP YOUR SECURITY
44. ll box Click lt Install gt and follow the steps to install the EasyConfig wizard on the desired computer VR Brickcom software Kii glish Install Adobe Reader 2010 Brickcom Corporation All Rights Reserved 12 BLOCK UP YOUR SECURITY rickcom 2 Inthe Install Shield Wizard dialog box click lt Next gt to continue Welcome to the InstallShield Wizard for Brickcom Software Kit The InstallShield Wizard will install Brickcom Software Kit on your computrer Click Next to continue or Cancel to exit the install Wizard Cancel 3 Read the End User License Agreement and check the option I accept the terms of the license agreement Click lt Next gt to continue Brickcom Software Kit InstallShield Wizard License Agreement Please read the following license agreement carefully End User License Agreement IMPORTANT READ CAREFULLY This End User License Agreement the Agreement is a legal agreement between you either an individual of an entity and BRICKCOM CORPORATION BRICKCOM regarding the use of the BRICKCOM s software entitled Brickcom Software Kit version 1 4 9 which may include user documentation provided in online or electronic form the Software By clicking the button marked ACCEPT or YES below you agree to be bound by the terms of this Agreement If you do not agree to the terms of this Agreement please do not install or use the Software 1 Grand of License
45. lly reflect the display of the live video Flip Enable to vertically reflect the display of the live video Flicker Free Eliminate the problem of flicker Click the Radio button to select outdoor or indoor mode based on the conditions Color Effect Select to display color or black and white video streams Click Apply to apply settings or Cancel to cancel changes 35 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Video The Network Camera offers two separate streams for different viewing options Stream Video Overlay RTSP Server Save File Folder Stream 1 a 1500Kbps se 1500Kbps Bitrate p Stream 2 Stream 1 amp Stream 2 Video Codec The Network Camera offers three choices of video codec standards for real time viewing H 264 MPEG 4 and MJPEG Video Resolution Select from the drop down menu to choose the best resolution recording settings Frame Rate Select the frame rate from drop down menu When H 264 or MJPEG is selected the frame rate ranges from 1 to 30 fps When MPEG 4 is selected the frame rate ranges from 1 to 15 fps Set a higher frame rate for smoother video quality Video quality and bit rate Choose either quality or bitrate to control the video quality with video codec at H 264 or MPEG4 Only quality can be chosen when video codec at MJPEG is selected Set the bitrate higher for a better video quality 36 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom A NOT
46. log or click Save to file to save the system log 69 BRICKCOM COMI BLOCK UP YOUR SECURITY Brickcom Remote Logging System Log Remote Logging Enable Dome OD IO TT Tm The user can configure the camera to send the system log file to a remote server as a log backup Click to enable remote log and enter the IP address of the remote server Enter the port number of the remote server Click Apply to apply settings or Cancel to cancel changes 70 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Date and Time Manual Manually enter the date and time Clone from PC The camera will sync with the time date and time zone of the computer used to modify the camera settings Check Clone to utilize this option The read only date and time of the PC will be displayed NTP Network Time Protocol NTP is a protocol for synchronizing the clocks of a computer system Select to update the time with a NTP server on an hourly daily weekly or monthly basis Time Zone Select the local time zone from drop down menu NTP Server 1 and Server 2 Enter the address of the NTP server Daylight Saving Enable this option to automatically update for Daylight Savings Time Date and Time NTP Server 1 tick stdtime gow tw NTP Server 2 clock stdtime gov tw Daylight Saving C Enable Click Apply to apply settings or Cancel to cancel changes 71 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom De
47. nect to camera but unable to access the internet then the installation will fail because the computer will not be able to download the latest root certificate This problem can be resolved if computer can be connect to the internet and the camera at the same time and will not recur when Windows update patches become available 30 BRICKCOM COM BLOCK UP YOUR SECURITY Live View Brickcom WCB 1 00Ap Camera Configuration Utility Live View Configuration Language Help Stream 1 Channels HTTP Y Protocol OFF LED Control Camera Name WCB 100Ap 2c11 2009 01 01 00 03 56 H 264 1280x800 Playing Camera Control Panel ay E Y 5H Brightness o ia os ir Mic Volume a e q 4 m 4 a l eeo RR e Speaker Volume IDO DY A A A Y o uv i A O MD E O a o sia o noi A voo os RS Ea SST eT os oe we eae ew ew eae ese ee FTF NO OR DE A i o S A NOTE These are optional features Please refer to the Product List for the full list of optional features available for the product Live View is the default page that opens when accessing the camera Live video is displayed directly in the browser window Stream1 Stream2 Channels The network camera offers simultaneous dual stream for optimized quality and bandwidth Go to Configuration Camera Video Audio Video to configure the codec compression and video resolution or refer to the Video configuration page e HTTP TCP UDP protocol H
48. ons for connecting the camera to a power and Ethernet source The camera can either be connected to a PoE enabled switch or a non PoE switch A If using a PoE enabled switch l 1 Use a single Ethernet cable to connect the camera to the PoE enabled switch B If using a non PoE switch 10 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom 5 Use a standard Ethernet cable to connect the camera to a PoE Injector 6 Use a standard Ethernet cable to connect the PoE Injector to the non PoE switch 7 Use a standard power cable to connect the PoE Injector to a power outlet adile BRICKCOM COM BLOCK UP YOUR SECURITY Software Installation In this manual User refers to whoever has access to the Network Camera and Administrator refers to the person who can configure the camera and grant user access to the camera After checking the hardware connection run the Installation Wizard program included on the products CDROM to automatically search the intranet for the camera There may be many cameras on the local network Differentiate the cameras using the serial number which is printed on the labels on the carton and the bottom of the camera 1 Insert the Installation CD into the CD ROM driver Run Auto Run Tool directly from the CD ROM to start the installation When installing the Brickcom software kit for the first time select a desired language for the interface The available languages are listed in the scro
49. over SSL Secure Socket Layer It helps protect streaming data transmission over the Internet on a higher security level than HTTP Click Enable to enable and Apply to apply settings or Cancel to cancel changes To enable HTTPS users have to create and install a certificate 1 Click Continue to this website to install x There is a problem with this website s security certificate The security certificate presented by this website was issued for a different website s address Security certificate problems may indicate an attempt to fool you or intercept any data you send to the server We recommend that you close this webpage and do not continue to this website Click here to close this webpage Continue to this website not recommended More information 53 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom 2 Enter the User name and Password of the camera Connect to 192 168 1 1 The server 192 168 1 1 at Brickcom IPC4M Login requires a username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection User name admin e Remember my password 3 Click Certificate Error on the top right corner of the window to view the certificate Gy y https J 192 168 1 103 w kl Certificate Error X ty Mismatched Address The security certificate p
50. ption method with dynamic encryption keys Shared Key Enter the key shared between the Router and the server keys Enter a password of 8 63 characters A NOTE If using WPA or WPA2 each device in the wireless network must use the same WPA or WPA2 method and shared key or else the network will not function properly 50 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Advanced Settings Basic Settings Advanced Settings Wi Fi Protected Setup Auto 20 40MHz Channel Network Mode From the drop down menu select the wireless standards running on the network lf there are Wireless B Wireless G and Wireless N 2 4GHz devices on the network use the default setting BGN Mixed If there are Wireless B and Wireless G devices on the network select BG Mixed lf there are only Wireless B devices on the network select Wireless B Only lf there are only Wireless G devices on the network select Wireless G Only lf there are only Wireless N 2 4GHz devices on the network select Wireless N Only If there are Wireless A and Wireless N devices on the network select AN Mixed lf there are Wireless A Wireless B Wireless G and Wireless N 2 4GHz devices on the network use the default setting ABGN Mixed lf there are only Wireless A devices on the network select Wireless A Only Radio Band The settings are available for the Auto 20 40MHz channel and Standard 20 MHz channel Enable WMM 802 1e QoS WMM is a wireless Quality o
51. resented by this website was issued for a different website s address File Edit view Favorites Tools Help we de Give view This problem may indicate an attemptto fool you or intercept any data you send to WCB 1 00Ap Camera Configur MESANA We recommend that you close this webpage About certificate errors Stream 1 f 2009 01 01 00 06 44 H 264 1280x800 Playing View certificates pra Contre 4 Click Install Certificate and follow the steps to finish the installation Certificate NI E General Details Certification Path de Certificate Information This certificate is intended for the following purpose s Ensures the identity of a remote computer Issued to Brickcom Issued by Brickcom Yalid from 7 8 2009 to 7 3 2029 Install Certificate 54 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Event Event Settings When an event Such as unauthorized movement occurs the camera can be scheduled to perform certain actions An Event Type is a set of parameters that defines these actions This section describes how to configure the camera to perform certain actions when events occur Event Settings Event List Add Event Delete Event Click lt Add Event gt on the Event Settings page The Event Setup page will appear Event Settings Event List FIR Motion Detection Save Stream Take Snapshot FEE balas Event O Always Event Sched
52. rveillance solution for residences and small businesses EasyLin Cube series which allows for users to simply plug in the camera to any home or small business network and play the video This camera series offers a user friendly and unique design which allows anyone without a technical background to use it lt features live video feed and two way audio which can be used over a local area network LAN through any internet browser or via any 3G mobile device PoE Power over Ethernet supported let camera CB 101A CB 102A can receive power through the same cable as for data transmission which simplifies installation since there in no power adapter needed For external alarm and sensor devices they can be equipped via PoE Cube s CB 101A CB 102A DI DO The PoE Cube series features many cutting edge functions and its fashionable streamline design make it the perfect additional for any home or office The Brickcom CB 102A is equipped with a CS mount which allows users to change the camera lens This interchangeable lens capability enables users to use a lens which gives the exact angle of view or distance they desire Because of its many advanced features the PoE Cube series has many versatile applications Users can easily monitor the safety of their family members pets office valuables and property 1 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom ED w Small Office Surveillance Security systems for small offic
53. ry card Click Format to format the Micro SD SDHC memory card Left click on the folder to list the recorded files The user can either play the snapshot of the recorded files by moving the mouse pointer over the file or double click on a file to play it Right click on the folder to download play or delete the recorded files A NOTE The user may need to install QuickTime multimedia framework to play the video clips 73 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Advanced Settings Storage Management Advanced Settings Automatic Recycle Enable Offline Record Come o o TT lf the Automatic Recycle function is disabled there must be at least 50MB Hard Drive space available for the network camera to record video lf the Automatic Recycle function is enabled it will automatically overwrite the recorded files when the available space remaining is less than 100MB Automatic Recycle Enable to automatically overwrite older files when the available space remaining on the Micro SD SDHC card is less than 100MB If the Automatic Recycle function is disabled there must be at least 50MB hard drive space available for the camera to be able to record video files Offline Record Enable to keep recording if the Network Camera is offline Click Apply to apply settings or Cancel to cancel changes LED Indicators The LED on the front of the camera can be configured to remain unlit Check OFF to enable t
54. the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation A IMPORTANT NOTE FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body This transmitter must not be co located or operating in conjunction with any other antenna or transmitter The availability of some specific channels and or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination The firmware setting is not accessible by the end user BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Package Contents Please check to make sure the product package contains all the accessories listed below a Network Camera b Product CD CB 100A CB 101A CB 102A c Camera Stand d Warranty Card Warranty Card CB 100A CB 101A CB 102A e Terminal I O Connector Block f Easy Installation Guide g 1 5m White Flat RJ 45 cable h Power Adapter CB 100A CB 100A BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Cube Network Camera Overview The compact Brickcom PoE Cube network camera series offers a high quality video k is a feature of the PoE su
55. ually gt The DHCP setting is recommended Brickcom select the IP Address settings Settings remains the same O Automatically obtain an IP Address DHCP O Set IP Address configuration manually a If lt Set IP Address configuration manually gt is selected the following pages will be displayed Brickcom select the IP Address settings Settings remains the same Y Automatically obtain an IP Address DHCP Set IP Address configuration manually 23 BLOCK UP YOUR SECURITY Brickcom Enter the static IP Address to configure IR Camera IPF Address 10 5 42 103 Subnet Mask 255 255 255 Q Gateway 10 5 42 254 DNS 1 l 103 Ds 0 24 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom 6 If the camera supports the EasyLink function the following page will be displayed Otherwise this page will not be shown If desired click lt Skip gt to skip this setting a AA AU a i Aa A il a se 15 EasyLink Settings You can use EasyLink Settings to connect to the IP camera without knowing the IP address EasyLink Name 0026821 bdbfd 2 Live View Windows Internet Explorer Ea tx amp http 0026821bdbfd mybrickcom com WFB 100Ap Camera Configuration Utility Enter the EasyLink URL into a web browser to access the camera s web GUI EasyLink is a unique Brickcom function which allows users to assign a unique EasyLink name to their network cam
56. ule Schedule Recurrence Pattern Motion Detection C Save Stream to C send Snapshot to O Play Audio Clip There is no available audio clip Configure one here O activate Digital Output C Send HTTP Notification C Send to Email C LED Light C Send UDP Notification to IP address LL lo IL J eon C send Multicast Notification to IP address C IO IO I Troal 55 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom How to Set Up an Event Schedule Event Schedule describes how and when the camera performs certain actions 1 Check Enable and enter a descriptive name for the event schedule 2 Set Event Schedule to define when the event is activated by selecting from Always 24 hours Schedule or Recurrence pattern a If Schedule is selected from the Event Schedule the following page will be displayed Do O Always Schedule Event Schedule event schedule _ Not Scheduled O Recurrence Fattern Motion Detection v C Save Stream to E Send Snapshotto Play Audio Clip There is no available audio clip Configure one here C Send HTTP Notification Send to Email C LED Light C Send UDP Notification to IP address PL JL IE frol C Send Multicast Notification to IP address Cab JEO IE Jroal i A Scheduled Event can be programmed for certain times and day Click individual boxes to schedule specific times for the camera to detect events 56 BRICKCOM COM BLOCK UP YOUR
57. vice Information System Information Displays the complete system information of the camera System Information Hetwork Settings Video Audio Settings rare ren e nta ec OOOO Network Settings Displays the complete network settings information of the camera System Information Network Settings Video Audio Settings P Seting Tye Video Audio Settings Displays the complete video audio settings information of the Camera System Information Network Settings Video Audio Settings sean 1280x800 WXGA Stream 2 HO uses OOO 1280x800 WXGA was e Cw E 79 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Storage Management Storage Management is used to view all the recorded files on the Micro SD SDHC card Storage Management Advanced Settings Local Storage Information Total Capacity Used Space Available Space IPCAM_0001 2010 07 28 Wed 04 51 06 snapshot_20100728_045104 jpg 2010 07 28 Wed 04 51 04 snapshot_20100728_045106 jpg 2010 07 28 Wed 04 51 06 El videoclip_ch1_20100728_045349 mp4 2010 07 28 Wed 04 53 54 El videoclip ch1 20100728 045357 mp4 2010 07 28 Wed 04 54 02 z chi 20100728 045409 mnd 2010 07 28 Wed 04 54 14 E videoclip ch1 20100728 0454 E Download Wed 04 54 24 E videoclip chi 20100728 0454 Q Play Ved 04 55 04 E offline 2010 07 28 Wed 05 11 24 Delete Storage Management Click Reload to refresh the list of recorded files Click Remove to safely remove the Micro SD SDHC memo
58. ypes of security settings for streaming via RTSP protocol NONE and DIGEST If DIGEST authentication is selected user credentials are encrypted using MD5 algorithm thus providing better protection against unauthorized access Click Apply to apply settings or Cancel to cancel changes Save File Folder Stream Video Overlay RTSP Server Save File Folder Recording Folder Path Browse Snapshot Folder Path Browse Apply Recording folder path The destination for saving the recording video files Click Browse to specify the saving path 38 BRICKCOM COM BLOCK UP YOUR SECURITY Brickcom Snapshot folder path The destination for saving the snapshot files Click Browse to specify the saving path and select the format from the drop down menu Click Apply to apply settings or Cancel to cancel changes Audio The administrator can set up two separate streams for the camera for different viewing devices The administrator can enable or disable the audio function on either stream If audio enable is selected select the Audio codec from the drop down menu Stream Advanced Settings Stream 1 TT emb he Stream 2 Apply Advanced Settings Stream Advanced Settings Camera Speaker Echo Cancellation Apy Cancel el Camera Speaker If the speaker is enabled select the volume from the drop down menu Echo Cancellation Enabled Enable to avoid an echo Click Apply to apply settings

Brick Computer CB-101A Security Camera User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents