Bosch Appliances 5000 Security Camera User Manual
Contents
1. Priority Motion Color In AUTO mode Color the camera gives a color image as long as the light level permits Motion the camera avoids motion blur as long as the light level permits it switches to monochrome earlier than it would with Color priority AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Configuration en 33 Item Selection Description IR contrast mono Enhanced Normal Enhanced the camera optimizes contrast in applications with high IR illumination levels Select this mode for IR 730 to 940 nm light sources and for scenes with grass and green foliage Normal the camera optimizes contrast in mono applications with visible light illumination IR illumination mono Oto 15 Enter the strength of the external IR illumination to determine the night to day transition moment O is no IR illuminator 15 is very strong illumination Color burst mono On Off Off the color burst in the video signal is switched Off in monochrome mode On the color burst remains active even in monochrome mode required by some DVRs and IP encoders EXIT Returns to main menu Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 34 en Configuration FLEXIDOME 5000 AN 5 5 4 Enhance Dynamic Engine submenu Item Selection Description Dyn2. 5 3 5 4 Day Night switching The camera is equipped with a motorized IR filter The mechanical IR filter can be removed in low light or IR illuminated applications by software configuration settings If Auto switching mode is selected the camera automatically switches the filter depending on the observed light level The switching level is programmable In Auto switching mode the camera prioritizes motion the camera gives sharp images without motion blur as long as the light level permits or color the camera gives color pictures as long as the light level permits The camera recognizes IR illuminated scenes to prevent unwanted switching to color mode There are four different methods of controlling the IR filter via Bilinx communication automatically based on the observed light levels or as part of the programmable mode profile Camera control communication Bilinx This camera is equipped with a coaxial communications transceiver also referred to as Bilinx In combination with VP CFGSFT the camera setting can be changed from any point along the coaxial cable All menus can be accessed remotely giving full control of the camera With this method of communication it is also possible to disable the local keys on the camera To avoid loss of communication on an installed camera the Communication On Off selection is not available while using remote control This function can only be accessed with the camera butto
3. Figure 3 7 Surface mounting rear connection KA Solid surface three pre drilled 8mm holes and fit supplied plugs Three screws supplied with camera Three screws M5 supplied Integrated camera unit and base Surface mounting box VDA 455SMB Cap remove for side entry cables Conduit Cables o Io gr Eoo AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Connection and set up en 19 4 4 1 Connection and set up Power and video connections The wiring harness has a BNC connector to accept the video coax cable with male BNC connector and two stripped low voltage power wires for connection to a power connector A UTP adapter VDA 455UTP is available as an optional accessory to allow a UTP video cable to be connected to the BNC connector The easiest way to connect the cables is as follows 1 Bring the building connections through the surface cable hole so that they hang clear 2 Partially insert two screws into the pre drilled holes or adapter plate 3 Using one of the keyholes hang the mounting base of the camera module on one screw temporarily tilt the base slightly to gain access to the cable connections 4 Connect the BNC connector of the camera module to the video coax cable 5 Connect the stripped power wires red brown to the power supply connector Note For a DC supply the polarity is important Incorrect polarity does not damag
4. Returns to Install menu AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Configuration en 41 5 6 3 Synchronization submenu Item Selection Description Synchroniza Internal Internal for free running camera tion Line lock operation Line lock to lock to the AC power supply Vertical phase O 1 359 Adjusts the vertical phase offset when in LINE LOCK mode and a valid power supply frequency is detected level EXIT Returns to Install menu 5 6 4 Connections submenu Item Selection Description Heater Off Auto Select Auto to enable the thermostatically controlled heater function The heater switches on at approximately O C 32 F Bilinx Comms On Off If Off Bilinx communications is disabled Cable Off Default Cable compensation is used to avoid compensation RG59 RG6 the need for amplifiers in long distance coaxial connections up to 1000 m 3000 ft For optimum results select the coaxial cable type used or if unknown select default Compensation 0 1 2 15 Sets the level of cable compensation EXIT Returns to Install menu Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 42 en Configuration FLEXIDOME 5000 AN 5 6 5 Test signal submenu Item Selection Description Show camera Off On Select On to overlay the
5. 8 1 1 Dimensions 57 6 2 27 57 6 2 27 Leg ted Gi 33 3 1 31 66 5 2 62 85 3 35 ls 2 o Y M 95 3 7 Lt 158 6 22 mm in Figure 8 1 Dimensions Flush mount Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 52 en Technical Data FLEXIDOME 5000 AN 30 8 1 21 130 5 5 14 5158 6 22 mm in Figure 8 2 Dimensions Surface mount AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Technical Data en 53 8 1 2 Accessories BNC to UTP transceiver Surface Mount Box SMB Pendant wall mount Pendant ceiling mount Corner mount Bilinx communication interface box and software Contact a Bosch representative in your area for the latest available accessories or visit our website at www boschsecurity com Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 54 en Technical Data FLEXIDOME 5000 AN AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems Bosch Security Systems www boschsecurity com Bosch Security Systems 2013
6. FLEXIDOME 5000 AN Configuration en 37 5 5 6 VMD submenu Item Selection Description VMD area Submenu Select 1 of the 4 areas to enter the area set up menu to define the detection area VMD mode Off Silent Off Video Motion Detection VMD is OSD off Silent video motion generates silent alarm OSD video motion generates on screen text message alarm VMD O to 127 Sets the sensitivity for motion to the sensitivity desired level The longer the white bar the more motion is required to acitvate the VMD alarm Motion above this level activates alarm OSD alarm Alphanumeric Text for on screen display alarm 16 text characters maximum EXIT Returns to main menu Selecting an area for VMD masking To set up an area for VMD masking access the area menu by selecting the VMD Area option from the VMD menu Upon entering the Area menu the current area is displayed with the upper left corner flashing The flashing corner of the image can be moved with the Up Down Left Right arrow keys Pressing the Select key moves the flashing cursor to the opposite corner which can now be moved Pressing Select again freezes the area and exits the area menu Bosch Security S ystems Installation Manual AM18 Q0648 v1 0 2013 03 38 en Configuration FLEXIDOME 5000 AN 5 5 7 Image Adjustment submenu Item Selection Description Digital Zoom X1 x2 x4 x8 Select the zoom facto
7. Never open the casing of the camera The unit does not contain any user serviceable parts Ensure that all maintenance or repair work is performed only by qualified personnel electrical engineering or network technology specialists If in doubt contact your dealer s technical service center 7 1 1 Transfer and disposal The camera should only be passed on together with this installation guide The unit contains environmentally hazardous materials that must be disposed of according to law Defective or superfluous devices and parts should be disposed of professionally or taken to your local collection point for hazardous materials AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Technical Data en 49 8 Technical Data 8 1 Specifications Type number VDN 5085 3 VDN 5085 9 VDN 5085 A Lens 2 8 to 10 5 mm 9 to 22 mm 18 to 55 mm F1 2 F1 4 F1 5 Sensitivity 0 06 Ix 0 08 Ix 0 09 Ix 30IRE lt 0 03 Ix mono lt 0 04 Ix mono lt 0 05 Ix mono All versions Imager 1 3 inch 960H CCD sensor Maximum 720TVL resolution Rated supply 12 VDC voltage 24 VAC PAL 50 Hz NTSC 60 Hz SNR 54 dB Video output 1 Vpp 75 Ohm Synchroniza tion Internal Line Lock Shutter Auto 1 60 1 50 to 1 100000 Selectable fixed flickerless default Day Night Color Mono Auto Sens Up Adjustable from Off to 10x AGC AGC On or O
8. Off Automatically reduces the noise in the Low picture Medium A high selection may cause blur High A lower selection improves sharpness at the cost of more noise Peak White On Off Use Peak White Invert to reduce glare Invert from the CRT LCD display Use in ANPR LPR applications to reduce headlight glare Test on site to ensure that it does benefit the application and is not distracting for operators of the security system EXIT Returns to main menu Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 36 en Configuration FLEXIDOME 5000 AN 5 5 5 Color submenu Item Selection Description White balance ATW indoor ATW Auto tracking white balance ATW Outdoor allows the camera to constantly ATW hold adjust for optimal color Manual reproduction ATW hold Puts the ATW on hold and saves the color settings Manual the Red and Blue gain can be manually set to a desired position Speed Fast Adjusts the speed of the white Medium balance control loop Slow Red gain 50 to 50 Manual and ATW hold adjusts the Red gain Blue gain 50 to 50 Manual and ATW hold adjusts the Blue gain Saturation 15 to 5 Adjusts the color saturation 15 gives a monochrome image 0 gives the default saturation 15 gives the most saturation EXIT Returns to main menu AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems
9. a moist fluff free cloth or leather shammy may also be used Do not use liquid cleaners or aerosol cleaners Heat Sources Do not install the unit near any heat sources such as radiators heaters stoves or other equipment including amplifiers that produce heat Water Never spill liquid of any kind on the unit Lightning Take precautions to protect the unit from power and lightning surges Controls adjustment Adjust only those controls specified in the operating instructions Improper adjustment of other controls may cause damage to the unit Power sources Operate the unit only from the type of power source indicated on the label Servicing Unless qualified do not attempt to service this unit yourself Refer all servicing to qualified service personnel Replacement parts Use only replacement parts specified by the manufacturer Installation Install in accordance with the manufacturer s instructions and in accordance with applicable local codes Attachments changes or modifications Only use attachments accessories specified by the manufacturer Any change or modification of the equipment not expressly approved by Bosch could void the warranty or in the case of an authorization agreement authority to operate the equipment AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Safety en 7 1 3 1 3 1 Connection in outdoor applications Safety precautions Coax g
10. camera ID on ID the video test signal Test pattern Color bars Select the desired test pattern to help Raster installation and fault finding Impulse Cross Impulse Crosshatch EXIT Returns to Install menu 5 6 6 Camera ID submenu Item Selection Description Camera ID Enter a 17 character camera name Use Left Right to change position in the string use up down to select character Use Select to exit Display ID pos Off Topleft Select the screen position of the Top right camera ID Bottom left Bottom right Camera ID On Off Displays a grey border behind the border camera ID to make it easier to read MAC address Shows MAC address factory set cannot be changed Ticker bars On Off The ticker bar moves continuously to show that the image is live and not frozen or played back AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Configuration en 43 Item Selection Description Mode ID pos Off Top left Camera mode is displayed on the Top right screen in the selected position Bottom left Bottom right EXIT Returns to Install menu Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 44 en Configuration FLEXIDOME 5000 AN 5 6 7 Privacy masking submenu Item Selection Description Mask 1 to 15 15 different areas can be masked Pattern Black Grey Selects
11. 20402 Stock No 004 000 00345 4 Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 10 en Safety FLEXIDOME 5000 AN 1 6 UL certification Disclaimer Underwriter Laboratories Inc UL has not tested the performance or reliability of the security or signaling aspects of this product UL has only tested fire shock and or casualty hazards as outlined in UL s Standard s for Safety for Information Technology Equipment UL 60950 1 UL Certification does not cover the performance or reliability of the security or signaling aspects of this product UL MAKES NO REPRESENTATIONS WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT 1 7 Bosch notice More information For more information please contact the nearest Bosch Security Systems location or visit www boschsecurity com AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Introduction en 11 2 2 1 Introduction Features The FLEXIDOME 5000 Day Night WDR camera is a small discreet surveillance dome containing a high performance camera with integral varifocal lens It uses a wide dynamic range 960H CCD sensor for outstanding picture performance This surveillence dome can be mounted to an electrical box to a wall to a ceiling or in a corner The sturdy construction and the high impact resistant polycarbo
12. FLEXIDOME 5000 AN VDN 5085 BOSCH FLEXIDOME 5000 AN Table of Contents en 3 Table of Contents 1 Safety 5 1 1 Safety precautions 5 1 2 Important safety instructions 6 1 3 Connection in outdoor applications 7 1 3 1 Safety precautions 7 1 4 Important notices 8 1 5 FCC information 9 1 6 UL certification 10 1 7 Bosch notice 10 2 Introduction 11 2 1 Features 11 3 Installation 12 3 1 Unpacking 12 3 2 Disassembly 13 3 3 Mounting the unit 14 3 3 1 Mounting tips 15 3 3 2 Flush mounting 15 3 3 3 Surface mounting 16 4 Connection and set up 19 4 1 Power and video connections 19 4 2 Setting up the camera 20 4 2 1 Camera positioning 20 4 2 2 Menu navigation 21 4 2 3 Focal length and focus 23 4 2 4 Heater 23 4 2 5 Closing the unit 24 5 Configuration 25 5 1 Menus 25 5 1 1 Top level menus 25 5 1 2 Menu navigation 26 5 2 Pre defined modes 27 Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 4 en Table of Contents FLEXIDOME 5000 AN 5 3 Day Night switching 28 5 4 Camera control communication Bilinx 28 5 5 Main menu structure 29 5 5 1 Mode submenu 29 5 5 2 Exposure submenu 30 5 5 3 Day Night submenu 32 5 5 4 Enhance Dynamic Engine submenu 34 5 5 5 Color submenu 36 5 5 6 VMD submenu 37 5 5 7 Image Adjustment submenu 38 5 6 Install menu structure 39 5 6 1 Language submenu 40 5 6 2 Lens Wizard submenu 40 5 6 3 Synchronization submenu 41 5 6 4 Connections su
13. amic Off Off turns off all automatic scene Engine XF DYNAMIC detail and enhancements only HDR recommended for testing Smart BLC XF DYNAMIC extra internal processing is enabled for enhancing the visibilty HDR adds dual sensor exposure to the XF DYNAMIC features In harsh lighting conditions pixels from each exposure are mixed to give a more detailed image Smart BLC BLC window and weighting factor are automatically defined Camera dynamically adjusts these for changing light conditions Contrast Low Increases the contrast at medium Enhancement Medium brightness levels High Select Low for high contrast scenes Select High for low contrast scenes e g fog Sharpness 15 to 15 Adjusts the sharpness of the picture O corresponds to the default position A low negative value makes the picture less sharp Increasing sharpness brings out more detail Extra sharpness can enhance the details of license plates facial features and the edges of certain surfaces AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Configuration len 35 Item Selection Description 3D NR Off Automatically reduces the noise in the Low picture Medium This may cause some motion blur on High exceptionally fast moving objects immediately in front of the camera This can be corrected by widening the field of view or lowering the selection value 2D NR
14. bmenu 41 5 6 5 Test signal submenu 42 5 6 6 Camera ID submenu 42 5 6 7 Privacy masking submenu 44 5 6 8 Flip submenu 44 5 6 9 Defaults submenu 45 6 Troubleshooting 46 6 1 Resolving problems 46 6 2 Customer service 47 7 Maintenance 48 val Repairs 48 1 1 Transfer and disposal 48 8 Technical Data 49 8 1 Specifications 49 8 1 1 Dimensions 51 8 1 2 Accessories 53 AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Safety en 5 1 Safety 1 1 Safety precautions DANGER High risk This symbol indicates an imminently hazardous situation such as Dangerous Voltage inside the product If not avoided this will result in an electrical shock serious bodily injury or death WARNING Medium risk Indicates a potentially hazardous situation If not avoided this could result in minor or moderate bodily injury CAUTION Low risk Indicates a potentially hazardous situation If not avoided this could result in property damage or risk of damage to the unit Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 6 en Safety FLEXIDOME 5000 AN 1 2 Important safety instructions Read follow and retain for future reference all of the following safety instructions Heed all warnings on the unit and in the operating instructions before operating the unit 1 10 Cleaning Generally using a dry cloth for cleaning is sufficient but
15. e the camera but it will not switch on 6 In damp environments ensure that the connections are sealed The surface mounting box and the other mounting accessories have a sealed compartment for this purpose 7 Push the connections back through the surface cable hole 8 Secure the mounting base of the camera module to the surface with three screws Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 20 en Connection and set up FLEXIDOME 5000 AN 4 2 Setting up the camera 4 2 1 Camera positioning CAUTION The Heater will be hot when in operation Do not touch Always switch the heater off when working on the camera refer to Section 4 2 4 Heater page 23 and Section 5 6 4 Connections submenu page 41 To assist in setting up the camera connect a monitor to the miniature 2 5 mm jack socket 2 This socket provides a composite video signal with sync An optional cable code number S1460 is available for making this connection When the S1460 cable is attached there is no video available on the BNC connector to avoid interference Figure 4 1 Camera parts 1 Heater 2 Monitor jack socket AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Connection and set up en 21 Thumbwheels Navigation buttons 5 Focal length Focus Pan axis rotation Tilt axis rotation Twist axis rotation oOU oonao The physical default position of the cam
16. era is that the top of the image corresponds to the indication TOP CAUTION CCD image sensors are highly sensitive and require special care for proper performance and extended lifetime Do not expose them to direct sunlight or bright spotlights in operating and non operating conditions Avoid bright lights in the field of view of the camera 4 2 2 The camera module position can be adjusted along three axes When adjusting the camera position ensure that the picture display on the monitor is level Set the camera to the desired position by performing the following steps For horizontal adjustment along the pan axis A rotate the camera module in the base Do not rotate more than 360 To obtain a horizontal horizon for tilted ceilings or sidewall mounting rotate the base of the lens along the twist axis C to align the picture shown on the monitor Do not rotate more than 340 A For vertical adjustment along the tilt axis B loosen thumbwheels position camera then gently tighten thumbwheels to secure camera Do not rotate more than 90 Menu navigation Five keys located on the side panel are used for navigating through the menu system Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 22 en Connection and set up FLEXIDOME 5000 AN Up key Menu Select key center Right key Down key Figure 4 2 Navigation Left key Press the menu select ce
17. ff 0 40 dB selectable Dynamic engine XF Dynamic HDR Smart BLC Dynamic Range 94 dB Dynamic Noise 3D NR 2D NR Reduction Sharpness Sharpness enhancement level selectable White Balance ATW indoor ATW outdoor ATW hold and manual Contrast Enhancement Low Medium High Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 50 en Technical Data FLEXIDOME 5000 AN Test pattern generator Color bar Raster Impulse Cross Impulse Cross hatch Video Motion Detection VMD 4 areas fully programmable Privacy Masking 15 independent areas fully programmable black white grey noise E zoom Up to 16x Digital Image On Off Stabilizer Communication Two way Bilinx bi directional consumption Languages English Spanish French German Portuguese Russian OSD Simplified Chinese Modes 6 programmable preset modes 24 hour Traffic Low light Smart BLC Low noise Vibrant Peak White Suppresses highlights in scenes Invert Power 12 VDC 360 mA 700 mA with heater on 24 VDC 330 mA 650 mA with heater on Weight 750 g 1 65 Ib Operating 30 C to 55 C 22 F to 131 F temperature 50 C 58 F with heater enabled Controls OSD with softkey operation AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Technical Data en 51
18. ing box With a side connection remove the cap covering the side entrance With a rear connection leave the cap in place Attach the conduit to the mounting box Release the two clips at the bottom of the watertight connection compartment to remove it from the mounting box Open the cover of the watertight compartment in the mounting box by releasing the five clips Run the power and video cables through separate rubber grommets into the watertight compartment Run the cable from the camera into the watertight compartment through the supplied grommet Make the connection inside the watertight compartment and clip on the cover to seal it AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Installation en 17 Figure 3 5 Surface mounting box VDA 455SMB Note To ensure a watertight cable entry use round cables of between 5 and 6 mm 0 2 0 24 inches for power and video connection Note Use some silicon spray on the cable to help slide the grommets onto it e UU Figure 3 6 Surface mounting side connection 1 Solid surface pre drill three 8mm holes and fit supplied plugs Three screws supplied with camera Three screws M5 supplied Integrated camera unit and base Surface mounting box VDA 455SMB a ON Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 18 en Installation FLEXIDOME 5000 AN 6 Cables 7T Conduit
19. inside the water tight compartment After connections are made ensure that the watertight compartment is tightly closed and cables and conduits are properly sealed to prevent ingress of water Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 8 en Safety FLEXIDOME 5000 AN 1 4 Important notices Disposal Your Bosch product was developed and manufactured with high quality material and components that can be recycled and reused This symbol means that electronic and electrical appliances which have reached the end of their working life must be collected and disposed of separately from household waste material Separate collecting systems are usually in place for disused electronic and electrical products Please dispose of these units at an environmentally compatible recycling facility per European Directive 2002 96 EC CAUTION The Low Voltage power supply unit must comply with EN UL 60950 The power supply must be a SELV LPS unit or a SELV Class 2 unit Safety Extra Low Voltage Limited Power Source AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Safety en 9 1 5 FCC information FCC amp ICES Information U S A and Canadian Models Only This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonab
20. ion Selects the gain setting for Fixed gain operation 0 is no gain Actual AGC Displays the actual AGC value from the camera to help compare gain level with lighting levels and picture performance Sens Up Dynamic Off 2x 3x 10x Selects the factor by which the sensitivity of the camera is increased When active some noise or spots may appear in the picture This is normal camera behavior It may also cause motion blur on moving objects EXIT Returns to main menu Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 32 en Configuration FLEXIDOME 5000 AN 5 5 3 Day Night submenu Item Selection Description Day Night Auto Color Monochrome Auto the camera switches the IR cut off filter on and off depending on the scene illumination level Color the camera always produces a color signal regardless of light levels Monochrome the IR cut off filter is removed giving full IR sensitivity Switch level 15 to 15 Sets the video level in Auto mode at which the camera switches to monochrome operation A low negative value means that the camera switches to monochrome at a lower light level A high positive value means that the camera switches to monochrome at a higher light level Switch delay 1 2 3 5 10 20 30 60 120 240 s Sets the evaluation time in Auto mode for day to night transitions
21. is intended to help you identify the causes of malfunctions and correct them when possible Malfunction Possible causes Solution No image Defective camera Connect a local monitor transmission to to the camera and check remote location the camera function Faulty cable connections Check all cables plugs contacts and connections Incorrect cable When using DC power connections ensure that polarity is correct No connection The unit s configuration Check all configuration established no parameters image transmission Faulty installation Check all cables plugs contacts and connections AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Troubleshooting en 47 6 2 Customer service If you cannot resolve a fault please contact your supplier or system integrator or contact Bosch Security Systems Customer Service directly The Installer should write down all information regarding the unit so that it can be referenced for warranty or repair The version numbers of the firmware and other status information can be seen when the unit starts or by opening the Install menu Note down this information and the information found on the camera label before contacting customer service Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 48 en Maintenance FLEXIDOME 5000 AN 7 Maintenance 7 1 Repairs CAUTION
22. le protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures reorient or relocate the receiving antenna increase the separation between the equipment and receiver connect the equipment into an outlet on a circuit different from that to which the receiver is connected consult the dealer or an experienced radio TV technician for help Intentional or unintentional modifications not expressly approved by the party responsible for compliance shall not be made Any such modifications could void the user s authority to operate the equipment If necessary the user should consult the dealer or an experienced radio television technician for corrective action The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington DC
23. ly provides an optimal picture without the need for further adjustments Advanced set up options are available in a menu system for getting the best results under special circumstances The camera implements your changes immediately so that before and after settings are easily compared Menus Top level menus There are two upper level menus a Main menu and an Install menu The menus have functions that can be selected directly or submenus for more detailed set up To access the Main menu press the menu select button center for less than 1 second The Main menu appears on the monitor The Main menu allows you to select and set up the picture enhancement functions If you are not happy with your changes you can always recall the default values for the mode The camera also has an Install menu in which the installation settings can be set To access the Install menu press the menu select button center for longer than 2 seconds Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 26 en Configuration FLEXIDOME 5000 AN 5 1 2 Menu navigation Five keys are used for navigating through menu system Up button SI Menu Select button center dl D em Right button D RE Down button Left button Use the up or down keys to scroll through a menu Use the left or right keys to move through options or to set parameters When ina menu quickly double press the menu
24. mounting hardware such as an electrical box a surface box or other accessories are used Note AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Installation en 15 If the unit is to be surface mounted then use the Surface Mount Box SMB The SMB is sold as a separate item VDA 455SMB or is included with the unit with the surface mount option Other mounting accessories are also sold separately 3 3 1 Mo unting tips Use the mounting hole template to assist in marking the correct position for the camera to be mounted Refer to the dimensions on the mounting hole template to find the exact position of the screw holes and the entry hole for the cables Partially screw in two screws for the keyholes and use them to temporarily hang the camera while the connections are made 3 3 2 Flush mounting e Im e 0 UU 9 Figure 3 3 Flush mounting hollow surface 1 Ge Solid surface pre drill three 8mm holes and fit supplied plugs Three screws supplied with camera Integrated camera unit and base Cables Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 16 en Installation FLEXIDOME 5000 AN 0 0 Figure 3 4 Flush mounting electrical box 4S 1 Two screws not supplied 2 Integrated camera unit and base 3 4S electrical box 3 3 3 Surface mounting When using the surface mount
25. n dome protect the camera module from damage The camera is easy to install and ready to use and offers the best solution for demanding scene conditions Features include 1 3 inch 960H CCD sensor with wide dynamic range True Day Night performance with switchable IR filter T20TVL sensor resolution High Dynamic Range Indoor and outdoor use P66 and NEMA AN compliant High impact vandal resistant IK10 Privacy zones Detail enhancement Bilinx bi directional coaxial communication Wide operating temperature range Lens wizard Six pre programmed operation modes Dynamic noise reduction Multiple language on screen display Built in test pattern generator Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 12 en Installation FLEXIDOME 5000 AN 3 3 1 Installation Unpacking Unpack carefully and handle the equipment with care The packaging contains FLEXIDOME 5000 camera Important safety instructions Quick install instructions CD ROM Installation instructions Adobe Acrobat Reader Plastic bag with mounting hardware three SX8 4 5 6 mm mounting plugs and three matching mounting screws and special screwdriver bit for tamper resistant screws Plastic bag with two black rubber grommets for surface mount box Lens adjustment cap If equipment has been damaged during shipment repack it in the origi
26. nal packaging and notify the shipping agent or supplier WARNING Installation should only be performed by qualified service personnel in accordance with the National Electrical Code NEC800 CEC Section 60 or applicable local codes CAUTION The camera module is a sensitive device and must be handled carefully AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Installation en 13 3 2 Disassembly The flush mount version consists of the following parts Camera module and mounting base Inner liner with sealing ring Trim ring Dome Figure 3 1 Flush mount The surface mount version consists of the following parts Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 14 en Installation FLEXIDOME 5000 AN Surface mounting box Camera module and mounting base Inner liner with sealing ring Trim ring Dome Figure 3 2 Surface mount To disassemble the unit proceed as follows 1 Use the special screwdriver bit to loosen the three tamper resistant screws in the trim ring the screws remain in place 2 Remove the trim ring and dome by pulling them from the base 3 Remove the inner liner with sealing ring by pulling it off of the base 4 Remove the pink protective foam 3 3 Mounting the unit There are several ways to mount the unit The method of mounting depends on the type of surface and whether other
27. ns Bilinx communications can only be disabled using the buttons on the camera Disabled camera buttons When the Bilinx communications link is active the buttons on the camera are disabled AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Configuration en 29 5 5 Main menu structure Item Selection Description Mode Submenu Sets up operating modes 1 to 6 Exposure Submenu Exposure control Day Night Submenu Day Night for color mono operation Enhance Submenu Picture enhancement and performance Color Submenu White balance and color rendition VMD Submenu Video motion detection Image Submenu Sets up digital zoom or digital image Adjustment stabilization 5 5 1 Mode submenu Item Selection Description Mode 1to6 Selects operating mode Mode ID Alphanumeric Mode name 11 characters maximum Copy active Available Copies current mode settings to the mode mode mode number selected numbers Mode Submenu Restores camera to the factory default Defaults settings EXIT Returns to main menu Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 30 en Configuration FLEXIDOME 5000 AN 5 5 2 Exposure submenu Item Selection Description ALC level 15 to 15 Selects the video level range A positive value is more useful for low light conditions a negative value is more usef
28. nter key to access the menus or to move to the next or previous menu Press the menu select key for approximately 2 seconds to open the Install menu Use the up or down keys to scroll through a menu Use the left or right keys to move through options or to set parameters When in a menu quickly double press the menu select key to restore the selected item to its factory default To close all menus at once from any menu select the Exit item and hold down the menu select key until the menu display disappears AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Connection and set up en 23 4 2 3 Focal length and focus Before adjusting the focal length or focus place the lens adjustment cap on the lens to ensure that the image sharpness is the same as when the dome is in place 1 Connect a monitor or other display device to either the camera s BNC connector or to the optional cable 81460 on the monitor jack If 51460 is connected there is no signal on the BNC connector Press and hold the menu select center button until the Install menu appears The Set focus item is highlighted Do not change this selection as the camera is now in a special mode for adjusting focus To set the field of view of the varifocal lens loosen the focal length screw and turn the mechanism until the required view is displayed on the monitor Image goes out of focus Focus the image on
29. pattern for all masks White Noise Active On Off Turns each of the masks on or off Mosaic On Off Turns mosaic on or off Window Submenu Select to open a window in which to define the mask area Selecting an area for privacy masking To set up an area for privacy masking access the area menu by selecting the Area option from the privacy masking menu Upon entering the Area menu the current area is displayed with the upper left corner flashing The flashing corner of the image can be moved with the Up Down Left Right arrow keys Pressing the Select key moves the flashing cursor to the opposite corner which can now be moved Pressing Select again freezes the area and exits the area menu 5 6 8 Flip submenu Item Selection Description Flip Off Selects the flip mode horizontal Vertical Both EXIT Returns to Install menu AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Configuration en 45 5 6 9 Defaults submenu Item Selection Description Restore All No Yes Restores all settings of the six modes to their default factory values Select YES then press the Menu Select button to restore all values When completed the message RESTORED is shown Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 46 en Troubleshooting FLEXIDOME 5000 AN 6 Troubleshooting 6 1 Resolving problems The following table
30. r x16 DIS Off On Select On to stabilize the image EXIT Returns to main menu AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Configuration en 39 5 6 Install menu structure Item Selection Description Language Submenu Select on screen display OSD language Lens Wizard Submenu Select to optimize the focus point Synchroniza Submenu Sets synchronization parameters tion Connections Submenu Connection parameters Test signals Submenu Test patterns and texts Camera ID Submenu Select to access ID submenu Privacy Submenu Sets up a masking area masking Flip Submenu Selects flip submenu Default ALL Submenu Returns all settings for all modes to factory defaults Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 40 en Configuration FLEXIDOME 5000 AN 5 6 1 Language submenu Item Selection Description Language English Displays the menus on the OSD in the Spanish chosen language French German Portuguese Russian Simplified Chinese EXIT Returns to Install menu 5 6 2 Lens Wizard submenu Item Selection Description Set focus now Select to fully open the iris Follow the instructions for adjusting the focus for the lens After focusing the object of interest remains in focus under bright and low light conditions EXIT
31. rounding If an outside cable system is connected to the unit ensure that the system is grounded U S A models only Section 810 of the National Electrical Code ANSI NFPA No 70 provides information regarding proper grounding of the mount and supporting structure grounding of the coax to a discharge unit size of grounding conductors location of discharge unit connection to ground electrodes and requirements for the grounding electrode Power lines An outdoor system should not be located in the vicinity of overhead power lines electrical lights or power circuits or where it may contact such power lines or circuits When installing an outdoor system extreme care should be taken to keep from touching power lines or circuits as this contact may be fatal U S A models only refer to the National Electrical Code Article 820 regarding installation of CATV systems 12 VDC 24 VAC power source This unit is intended to operate with a limited power source this power source must comply with EN60950 User supplied wiring from 12 VDC 24 VAC supply to unit must be in compliance with electrical codes Class 2 power levels Do not ground the 12 VDC 24 VAC supply at the terminals or at the unit s power supply terminals Connection The unit has connection terminals on flying leads In wet or outdoor installations make use of the VDA 455SMB accessory or use a field wiring box with Nema 4 or IP66 protection level or better Make the connections
32. select key to restore the selected item to its factory default To close all menus at once hold down the menu select key until the menu display disappears or continually select the Exit item Some menus automatically close after about two minutes other menus have to be closed manually AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Configuration en 27 5 2 Pre defined modes There are six pre defined modes with settings to make configuration easier You can select one of the six pre defined modes in the Install Mode submenu The modes are defined as follows 1 24 hour Default installation mode to provide stable pictures over a 24 hour period These settings are optimized for out of the box installation Traffic Capture high speed objects using default shutter in variable lighting conditions Low light Provide extra enhancement such as AGC and SensUp to make usable pictures in low light conditions Smart BLC Settings optimized to capture details in high contrast and extremely bright dark conditions Low noise Enhancements are set to reduce picture noise Useful for conditional refresh DVR and IP storage systems because reducing noise reduces the amount of storage required Vibrant This mode has enhanced contrast sharpness and saturation Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 28 en Configuration FLEXIDOME 5000 AN
33. the monitor by loosening the focus screw and turning the mechanism until the image is in focus Re adjust the focal length if necessary Repeat these two adjustments until the desired view is in focus Tighten both screws Use the navigation buttons to move to Exit and press the center button until the menu disappears Remove the lens adjustment cap from the lens and disconnect the monitor 4 2 4 Heater When using the camera at low temperatures set the heater setting to Auto in the Install menu The heater turns on at ambient temperatures below 0 C 32 F Bosch Security Systems Installation Manual AM18 Q0648 v1 0 2013 03 24 en Connection and set up FLEXIDOME 5000 AN 4 2 5 Closing the unit When the camera position is set and all adjustments have been made close the unit 1 Place the inner liner with attached sealing ring in position aligning its fin with the bracket on the base 2 Place the dome onto the base and rotate until it clips into place If necessary clean its surface with a soft cloth 3 Place the trim ring over the dome 4 Align the tamper resistant screws in the trim ring with the threaded ends in the mounting base 5 Use the special screwdriver bit supplied to tighten the three tamper resistant screws AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Configuration en 25 5 5 1 5 1 1 Configuration The camera normal
34. ul for very bright conditions Some ALC adjustment may improve scene content when Smart BLC is enabled ALC speed Slow medium fast Adjusts the speed of the video level control loop For most scenes it should remain at the default value Shutter AES FL Fixed AES auto shutter the camera automatically sets the optimum shutter speed FL flickerless mode avoids interference from light sources recommended for DC iris lenses only FIXED allows a user defined shutter speed Default AES shutter or Fixed shutter 1 50 PAL 1 60 NTSC 1 100 PAL 1 120 NTSC 1 250 1 500 1 1000 1 2000 1 4000 1 10K 1 100K In DEFAULT AES mode the camera tries to maintain the selected shutter speed as long as the light level of the scene is high enough In Fixed mode selects shutter speed AM18 Q0648 v1 0 2013 03 Installation Manual Bosch Security Systems FLEXIDOME 5000 AN Configuration en 31 Item Selection Description Actual shutter Displays the actual shutter value from the camera to help compare lighting levels and optimum shutter speed during set up Gain control On Fixed On the camera automatically sets the gain to the lowest possible value needed to maintain a good picture Fixed sets Fixed AGC value Maximum AGC or Fixed AGC 0 to 40 dB Selects the maximum value the gain can have during AGC operat
Download Pdf Manuals
Related Search