BMW 325i Automobile User Manual
Contents
1. Turn Distributor Counter Llockwise to Advance Ignition Timing Catalog 3562 3563 3564 3565 Rev 3 06 Page 8 of 16 2006 Edelbrock Corporation Brochure 63 0047 16 17 HEATER HOSE SUPPLY LINE For all years the heater core supply will come from the right front water port on intake manifold You will need to install the 1 2 NPT to 3 4 hose fitting into manifold using Teflon sealant on threads Remove your existing heater supply hose at its junction point usually at the heater core Using the 3 4 heater hose and two clamps supplied route the hose from the intake manifold to the heater core supply entrance Some cutting of the hose may be required Secure hose on both ends with hose clamps INJECTORS AND RAILS NOTE Fuel injectors and fuel rails are assembled on manifold and ready to run unless you had to remove them for manifold installation If they were removed use the following procedure for re installation If not skip this procedure and move on to the next step Using non silicone based spray lubricant or white grease lubricate injector O rings top and bottom before sliding them into fuel rails Push injectors into rails making sure that the electrical connectors on injector bodies face up Now push fuel rails and injectors into manifold Use caution not to damage O rings upon installation Place fuel rail with pressure regulator on passenger s side with regulator toward rear of engine Place other2. disconnect your fuel fill neck from the bed With all bed bolts and wires disconnected four people can lift off the bed This takes about 20 30 minutes which is much faster than draining and removing tank With bed removed you will see top of fuel tank Take a brush or compressed air and clean the top of fuel sending unit area so no debris enters in fuel when removing this assembly Disconnect two fuel lines two hoses and an electrical connection with a ground wire There is a center fuel pump sending unit assembly lock ring holding assembly into tank 2006 Edelbrock Corporation Brochure 63 0047 Note There is a kit supplied with the 3501 and 3502 that provides you with new fuel line and clamps Install the 3 length of fuel hose onto the 3 8 steel tubing where the old fuel pump junction hose was previously Use the 3 8 hose clamp to secure hose to steel tubing Disconnect two fuel lines two hoses and an electrical connection with a ground wire There is a center fuel pump sending unit assembly lock ring holding assembly into tank Using a hammer and brass punch gently strike open edge of lock ring in a counter clockwise direction Keep hitting until lock ring rotates enough to release Again blow or brush top area clean and carefully remove the entire assembly Be careful on removal Take your time Note You may want to replace the fuel sock at this time with a new factory replacement Use a small flat blade screwdri
3. bolts Make all electrical connections Connect the throttle cable and cruise cable assembly Make vacuum connections at the rear of the throttle body as well as all of the connections in front Double check all ground connections and electrical connections Catalog 3562 3563 3564 3565 Rev 3 06 27 Page 12 of 16 ACCESS FUEL TANK For the TBI multipoint conversion it is necessary to install a high pressure fuel pump 3581 for single tank vehicles sold separately IMPORTANT NOTE On trucks with dual tank set ups it will be necessary to install Edelorock Dual Fuel Tank Conversion Kit 3580 available from your Edelbrock dealer or call Edelbrock directly for sales or dealer assistance 800 416 8628 Option 3 Dual tank vehicles do not require removal of the tanks or pick up bed as the new fuel pump kit 3580 mounts on the vehicle frame See installation instructions supplied in kit Dual Tanks Require Kit 3580 Bed does not need to be removed for dual tank pump installation To install pump 3581 on single tank vehicles you must gain access to the top of your fuel tank If you have a Suburban you will need to drain the fuel tank and drop from the rear of the vehicle If you have a truck we recommend removing the bed to reach the fuel tank On truck beds you will usually find eight mounting bolts two ground wires a couple of weather pack electrical connectors near license plate area and you will need to
4. coming off of the wire loom Catalog 3562 3563 3564 3565 Rev 3 06 24 29 Page 11 of 16 VACUUM HOSE Remove the factory molded vacuum line which ran from the MAP sensor to the rear of the throttle body Locate the 1 4 x 12 vacuum hose the 1 4 x 1 4 x 5 32 vacuum tee and the 24 of 5 32 vacuum hose from kit Put one end of the 5 32 hose on the vacuum nipple of the fuel regulator and loop it around the coil area be careful not to kink the hose The other end should end up in the area around the rear of the throttle body Install the 1 4 vacuum hose from the MAP sensor to the rear of the throttle body This is easier with the throttle body off estimate length if throttle body is not yet installed Insert plastic vacuum tee into the section of 1 4 vacuum hose where the 5 32 vacuum hose from the fuel regulator will easily intersect Cut the hose and insert the tee and connect all three hoses For vehicles with vacuum actuated EGR valve you will need to remove the hard preformed vacuum hose from the EGR vacuum regulating valve Install the remaining 5 32 vacuum hose from the EGR valve to the regulating valve cut hose as needed POWER BRAKE BOOSTER CONNECTION Vehicles equipped with vacuum booster need to use the vacuum port found at the right rear corner of the throttle body pad if not used plug with pipe plug supplied From kit contents locate the 2 ft x 15 16 vacuum hose two clamps 90 brass fitti
5. of the location of this wire consult factory service manual Re connect wire after timing is set If you have a truck re install bed after checking for leaks around sending unit assembly NOTE You may notice a slight surge in the idle in Park or Neutral This is normal and will smooth out when the transmission is shifted into any drive gear 2006 Edelbrock Corporation Brochure 63 0047 BASIC TROUBLESHOOTING Engine Combinations a If you assemble a combination of parts other than stock or the Edelbrock MPFI package called out in our catalog your vehicle may not perform properly Stroker motors are not supported All engine assemblies must maintain stock compression ratios d A 190 to 195 degree thermostat should be used for optimum mileage performance and emissions Thermostats temperatures below 185 degrees should be avoided oS Engine Assemblies a Heavy duty L19 454 1987 1990 P N 88890529 b Heavy duty L19 454 1991 1995 P N 88890530 C GM P N 12371054 Retrofit 8 2L 502 Long Block 3564 3565 MPFI Fuel Pressure Fuel pressure must be checked with a fuel pressure gauge only Do not use a tire pressure gauge Test a Turn key to On position but do not start the engine b Fuel pressure should read 42 45 psi depending on your altitude The higher the altitude the lower the pressure C The system s fuel pressure should not drop more than 10 psi in 5 minutes and should maintain residual pr
6. rail on driver s side of manifold Push down with enough force to seat lubricated O rings in manifold making sure not to cut O rings Once injectors are seated and before replacing the 1 4 20 x 1 25 bolts make sure the injectors rotate in their bores easily Once installed secure rails with 1 4 bolts and flat washers supplied in kit Torque to 8 ft Ibs Catalog 3562 3563 3564 3565 Rev 3 06 18 Page 9 of 16 FUEL LINE CONNECTION From the kit contents locate the length of 3 8 high pressure fuel hose one 45 6 Pushlock fitting one 90 Pushlock fitting and two straight 6 Pushlock fittings PUSHLOCK FITTING TO HOSE INSTALLATION Use this procedure for installing each one of the Pushlock Fittings onto hose ends Clamp Pushlock fitting in vise being careful not to crush fitting Lubricate inside of hose end and Pushlock fitting barb with a small amount of lubricant oil spray lube or white grease Push the hose over the barb until it stops against the fitting collar No clamping is necessary Before making the fuel lines you must install the fuel filter adapter fitting and the return line adapter fitting The fuel filter adapter fitting is a male 6 to 16mm threaded male with an 0 ring on the end of the fitting Install into fuel filter and tighten securely The return adapter fitting is the female 14mm to 6 fitting This will attach to the return fuel line NOTE Be careful not to damage the O rings on t
7. tie wrap L 1 1 2 hose clamps Q 1 Throttle cable bracket LJ 2 3 4 hose clamp OQ 1 Throttle body block off plate L 1 3 8 hose clamp fuel injection clamp OQ 1 Throttle body gasket L 1 5 16 hose clamp fuel injection clamp O 1 EGR gasket L 1 1 4 x 1 4 out x 5 32 bottom out vacuum T fitting O 1 3 8 NPT pipe plug L 1 10 16 x 3 4 TEX screw self tapping O 1 3 8 1D Flatwasher l 1 Air Cleaner Lid decal MANIFOLD ASSEMBLY CONTENTS Description Description Intake manifold Fuel regulator nut and Viton O ring Driver s side left side fuel rail Viton O ring fuel regular nut 1 2 o d 5 16 i d Passenger s side right side fuel rail 1 4 i d AN thin flat washers 1 4 20 x 1 25 Hex head cap screw rail hold down bolts 1 4 20 x 1 2 hex head cap screw Fuel pressure regulator 1 4 i d split lock washer Magnetti Marelli pico injectors Schrader valve cap Fuel crossover line including adapter and schrader valve 1 4 internal star lock washers Qty Q E Q E Q Q Q Q Fuel inlet fitting 3 8 male pipe to 6 AN male steel SUGGESTED TOOLS AND MATERIALS FOR INSTALLATION Q 3 8 ratchet socket set with extensions Q Intake gasket set Edelbrock 7205 GM 10181398 or _ Combination set of open end wrenches SAE and metric equivalent UO Jackstands screwdrivers pliers crescent wrench hacksaw Ld Thermostat housing gasket GM 10105135 Fel Pro 2201 or hammer brass punch and assorted hand tools
8. use the Edelbrock throttle bracket supplied in kit Remove remaining manifold bolts and brackets noting the location of studded bolts so you can replace them in the same location The MAP sensor bracket assembly is mounted on the right rear manifold bolts It will mount in the same location on new manifold If you remove any ground wires note their location as well MANIFOLD REMOVAL Using a flat blade screwdriver or a small pry bar wedge tool under front end seal of the intake manifold and pry to break seal Remove intake manifold being careful not to spill too much coolant into engine If any coolant is spilled use paper towels to absorb quickly Clean out any debris that may have fallen in engine valley upon removal of manifold Place rags over valley and place rags or paper towels into all exposed ports on cylinder heads to keep out debris Catalog 3562 3563 3564 3565 Rev 3 06 12 Page 6 of 16 FUEL LINE REMOVAL Remove two existing fuel lines hanging over the rear near center of the engine block On most late models 1992 1995 the fuel lines are routed down the left side of the truck coming down the bellhousing and running over to the frame where they connect to the fuel filter The return line will have a coupler type fitting where it connects Remove these lines they will not be used with the new kit Be careful of any remaining fuel in lines Then there will be a mounting clamp holding lines to the upper lef
9. 5 7 4L Chevy GMCs originally equipped with Throttle Body Injection These complete systems utilize the stock computer and throttle body unit for a simple and effective conversion to multi point fuel injection Fuel is injected directly into each port in the head for ideal fuel distribution and efficiency TECHNICAL SUMMARY In 1987 Chevrolet introduced their Throttle Body Injection TBI systems Produced from 1987 to 1995 on all pick up trucks and Suburbans this TBI system was essentially an intermediate step between a carburetor and true port multi point fuel injection In these TBI systems two injectors are positioned above the throttle blades of a two barrel throttle body and fuel is injected into the manifold much like a carbureted system This arrangement suffers from distribution problems because the fuel spray from the injectors does not stay in suspension with the incoming air resulting in uneven distribution Our Performer Multi Point Systems include an intake manifold designed to deliver an equal air charge to each cylinder Each injector delivers exactly the same amount of fuel to each cylinder for an extremely even air fuel ratio from cylinder to cylinder This permits us to tune the system for ideal fuel and spark delivery for more horsepower torque and improved mileage Performer Multi Point Systems include all parts needed to make the conversion The stock TBI unit is retained as an air valve and the factory computer re programmed i
10. PERFORMER MULTI POINT EFI SYSTEMS for TBI Equipped Chevrolet GMC Trucks amp Suburbans Catalog s 3562 3563 3564 and 3565 INSTALLATION INSTRUCTIONS STOP BEFORE BEGINNING INSTALLATION READ THESE IMPORTANT NOTES Q You must purchase a separate Edelbrock Fuel Pump Kit for this installation single fuel tank vehicles use Edelbrock 3581 dual tank vehicles use 3580 Q Check the Kit Contents and Suggested Tools lists on page 2 to be sure that you have all items necessary to finish installation Make sure this kit is for your vehicle _ The kits are designed to work with stock engines with stock compression ratios The 3564 and 3565 are designed to work with the GM 12371054 502 c i d crate engine Q You must change your computer chip for this kit to function on your vehicle and be emissions legal Complete the Chip Information Card and return to Edelbrock We will send the computer chip within the continental U S free of charge via UPS second day air Orders outside of the continental U S will be shipped via the best method at the same costs as continental UPS second day air If requested customers may pay for expedited shipping by providing a current Visa or Master Card _ Your vehicle s wiring harness and electronics must be in good shape or you may not get maximum performance and or may experience problems The TBI will work with less adequate connections but the Performer Multi Point EFI System is much more sen
11. acket there will be two support brackets running from different locations on the backside of the A C compressor both meeting the manifold at one spot Remove bolts and brackets Brackets will be re used Alternator has a support bracket running from the two left front intake manifold bolts to the rear of the fan belt tension assembly and the upper alternator bolt this will be re used during assembly Release the belt tension using a ratchet and socket then remove the fan belt E j g T E Altert ator_ e h Pa Ps 1 lt n W 1 Remove top alternator mounting bolt and the bolt holding the belt tension assembly Remove two bolts that hold bracket to left front support base which is mounted to the two left front manifold bolts Remove bracket assembly NOTE On later vehicles this procedure may not be required 2006 Edelbrock Corporation Brochure 63 0047 10 11 DISTRIBUTOR REMOVAL Remove plug wires from top of distributor cap Make note of location of each wire Remove distributor cap Before removal of distributor note the location of the distributor body and the ignition rotor by marking distributor body with a felt tip marker Loosen distributor clamp and remove distributor Be careful not to turn engine over after distributor has been removed With the distributor removed remove the ignition coil and throttle bracket NOTE On early applications you will not re use your throttle bracket You will
12. d Install coil wires and electrical connections on coil and distributor Re install your MAP sensor bracket which mounts on right rear second and third studded manifold bolts Install the EGR vacuum regulator valve on the third bolt from the front on the right side HEATER FITTING 1 2 PIPE 3G PIPE 38 16 UNL 4 PLE 12 PIPE a JE 1d UNC B FLL 15 If your vehicle has the bracket for the alternator and idler belt tension pulley you need to install it at this time Re install tensioner and bracket assembly Re install serpentine belt Make sure tensioner bolt and bracket bolts are tight THERMOSTAT AND HOSES If your vehicle came with the 44mm O ring style thermostat you will need to purchase a standard size thermostat and gasket You will re use your original housing Thermostat operation and engine coolant temperature are very important for proper ECM operation Check service information for suggested temperature usually 195 degrees Install thermostat and housing Re install ground wire to one of the thermostat housing mounting bolts if originally equipped Install radiator hose and water pump bypass hose Re install the coolant temperature sending unit located to the right of the water pump bypass hose Check coolant sensor wire connection and make sure all hose clamps are tight CYLINDER NUMBERING a O w lo lo UNC 4 PLL Intake Manifold Bolt Tightening Sequence Big Block Lhewy Firing inde l 9 4 3 6 57 7 2
13. equivalent LJ Torx screwdrivers Q Gasket sealant Gasgacinch etc L Tin snips Q RTV Silicone sealant 02 sensor safe L White grease Q Wire stripper amp crimper LI Teflon thread sealant or equivalent L Heat gun or lighter Catalog 3562 3563 3564 3565 2006 Edelbrock Corporation Rev 3 06 Page 2 of 16 Brochure 63 0047 IMPORTANT INSTRUCTIONS For ordering your FREE Edelbrock computer chip You must use an Edelbrock chip with the Performer Multi Point EFI conversion You must change the computer chip in your stock computer ECU for proper functioning and maximum performance with the Edelbrock Performer Multi Point EFI for 7 4L or 8 2L Chevy GMC engines To receive your ECU chip please complete the attached postage paid card and send to Edelbrock After receiving your card Edelbrock will send the computer chip within the continental U S free of charge via UPS second day air Orders outside of the continental U S will be shipped via the best method at the same costs as continental UPS second day air If requested customers may pay for expedited shipping by providing a current Visa or Master Card When filling out your information card please print clearly The information below will help you to locate your ECM Service Number and Broadcast Code Typical ECM Label SERVICE NUMBER gt SERV NO 16144288 BROADCAST CODE SGAWHF K112731181 16159501 AWHF WHFK1I112731181 A 8 6 1 The ECM is accessible in pick ups b
14. essure even after sitting for 24 hours If pressure drops more than 10 psi check fuel pump hose and clamps in fuel tank If the original hose and clamp were used replace them with the supplied hose and clamps per the instruction If fuel pressure still drops off too quickly contact Edelbrock d With engine running check fuel pressure The idle fuel pressure should be between 34 38 psi depending on idle vacuum Engine Runs On Only One Bank a Check injector wiring for correct connections green to green blue to blue or red to red Some cases white to red b Check that your original MemCal blue capped chip is installed on the supplied green piggyback adapter and chip alignment in the green piggyback adapter See New Computer Chip Installation section and diagram on page 15 Edelbrock Corporation 2700 California St Torrance CA 90503 EFI Tech Line 800 416 8628 Option 3 E Mail EFlTech Edelbrock com Catalog 3562 3563 3564 3565 2006 Edelbrock Corporation Rev 3 06 Page 16 of 16 Brochure 63 0047
15. he fittings or the existing fuel lines Install both fittings as shown in photo Fuel Filter Adapter UCE i Return Line Adapter Fitting Mum 2006 Edelbrock Corporation Brochure 63 0047 19 20 FUEL RETURN LINE INSTALLATION Install the 90 6 pushlock fitting into the 10 foot length of hose using the pushlock fitting installation procedures described previously Tape off the open end of fuel line to prevent debris from entering Route the open end taped of hose down the bellhousing towards the fuel filter and return line area NOTE This may be left or right side depending on year and model Connect the 6 90 fitting to the fuel pressure regulator fitting on fuel injection assembly passenger s side fuel rail Be sure that the hose is routed safely with no sharp bends down the bellhousing to the frame where the connection will be made Determine the length needed adding in a little extra to allow mounting fuel line clamp to the floor of vehicle Mark the line remove from vehicle and cut to length NOTE Carefully flush out all debris after cutting lines Install 6 straight pushlock into hose Tape end of return line again then re install on vehicle Tighten both fittings securely FUEL INLET LINE INSTALLATION Install the 45 6 pushlock fitting into the remaining length of hose and tape other end to prevent debris from entering Route open end taped of hose down bellhousing and thread 45 fitting
16. ibration EErEE ttt PRR RR RR RRO RED Se ee 2 E a Q oo o f i ht Q w e X we a7 7 ot A ae ns Adapter Module Catalog 3562 3563 3564 3565 Rev 3 06 31 32 Page 15 of 16 INITIAL START UP Re connect battery negative cable Double check connections and fill radiator with a 50 50 mix or manufacturer s recommendation of anti freeze and water Turn key to the On position You will hear the fuel pump run for a few seconds and stop as it fills the fuel system with fuel There will be air trapped in system At this time inspect all fuel connections for leaks If there are no leaks and everything looks good crank it over It might not start right away If not stop and cycle key so fuel pump runs this will allow air trapped in system to evacuate Try to start again Once running check for fuel leaks again then water leaks SET IGNITION TIMING lf there are no leaks set ignition timing following manufacturer s procedures and specifications You must disconnect the ignition interrupter wire before you set the timing This is a single tan wire with a black stripe and a black plastic connector On late style vehicles it is usually found under the dash on the passenger s side between the blower motor and the duct work next to the courtesy light On earlier vehicles it is usually found on the passenger s side firewall behind a plastic cover which is secured with two screws If you are not certain
17. lamp and the electrical connections on the pump Some shortening of the rubber hose may be necessary for proper alignment of the pump with the pump hanger New Hose 5 16 5 16 Clamp NOTE DO NOT RE USE THE ORIGINAL IN TANK FUEL HOSE OR CLAMPS Use the new rubber base gasket for fuel pump If the big O ring in fuel tank is OK not torn you may reuse it If necessary replace with original equipment O ring from a GM dealer Make sure to grease large O ring with white grease or equivalent Making sure clamp is tight and electrical connector is connected install strainer sock into same position it will just push on with your thumb Install complete assembly back in the fuel tank Make sure you do not bend anything while reinstalling Lock assembly back in place by rotating lock ring clockwise until it hits its stops Now tighten fuel connections and hose clamps Make electronic connection and ground connection Re install fuel tank Suburbans etc Do not re install bed on pick up trucks at this time Before installing bed see Fuel Pressure Test Section on page 15 Catalog 3562 3563 3564 3565 Rev 3 06 29 30 Page 14 of 16 HOT RESTART FUEL MODULE You must remove the Hot Restart Fuel Module before starting your 1987 1989 over 8600 Ibs GVW HD vehicle The Hot Restart module is located on the Break Pedal Bracket between the firewall and the back of the gauge cluster Its dimensions are approximatel
18. ng and 3 8 NPT to 1 2 hose fitting Install 90 fitting in vacuum port using teflon sealant then install 3 8 to 1 2 hose fitting into 90 fitting aiming the hose end of fitting towards vacuum brake booster Remove original 90 plastic fitting from booster supply line and install in end of vacuum brake hose supplied Clamp fitting to hose Route hose to vacuum supply port 90 fitting just 2006 Edelbrock Corporation Brochure 63 0047 26 installed in manifold Route hose and cut as necessary to prevent interference with linkage Tighten both clamps and secure with tie wrap as shown Hose From Booster to Supply Port m a i k i age an O j Ca ri ee F a a 3 r 4 THROTTLE BODY CONVERSION Remove the fuel inlet and return fittings at rear of the original throttle body assembly Next remove three torx screws retaining the fuel injector regulator assembly to the main body Remove this assembly while leaving the factory gasket in place Using the factory torx screws install the injector block off plate supplied in kit The throttle body is now ready to be installed using the new base gasket supplied in kit Once installed make sure all vacuum and electrical connections are secure Make throttle connections Stock TBI Injector Modified TBI Injector Install the converted throttle body assembly and the new throttle body base gasket supplied onto the manifold Install and tighten three mounting
19. onto rear of fuel rail From under vehicle determine length needed to reach the fuel filter adapter fitting Be sure to add a little extra to allow mounting a fuel line clamp to the floor of vehicle Remove line from vehicle and cut to length Install 6 straight pushlock into hose Tape end of return line again then re install on vehicle Tighten both fittings securely ae Driver s Side Fuel Rail With the lines routed so they are not kinked use the fuel line clamp kit supplied to mount to the floor IMPORTANT NOTE Using two zip ties fasten the fuel lines to wire harness running down transmission and possibly one up top to ensure that they are not touching firewall or any other sharp areas Catalog 3562 3563 3564 3565 Rev 3 06 21 22 Page 10 of 16 THROTTLE BRACKET On all vehicles with a vacuum actuated cruise control 1987 1991 you will need to install the throttle bracket supplied Install this bracket on the studded intake manifold bolts on the left side of the manifold third and fourth bolts from the rear Later vehicles use the stock bracket Install bracket and connect throttle cable to your new or existing bracket INJECTOR HARNESS Lay out the injector harness supplied in kit on the engine looping it around the backside of the throttle body pad The tee with pink line connectors coming out of the bottom should end up by the right rear of the throttle body pad just in fron
20. otice that it is relocated up near the thermostat area The EGR mounting pad is drilled for the different EGR valves used from year to year We provide a gasket that will accommodate all EGR valves Determine which EGR bolt holes are to be used and install your old studs and EGR valve onto manifold For models equipped with a power brake vacuum booster you will need to install the 1 2 NPT to 1 2 barbed 90 degree fitting This will be used later in the installation for your vacuum supply relocation This fitting goes on the rear of the throttle body pad NOTE f any of the holes in the manifold are not used plug them with the pipe plugs supplied and always use Teflon sealant or equivalent when installing fittings and plugs does not apply to unused EGR pad holes Stock EGR Location Das Catalog 3562 3563 3564 3565 Rev 3 06 14 Page 7 of 16 NOTE On early models 1987 1990 the cruise control vacuum diaphragm bracket is mounted directly on the intake manifold For these models it is necessary to relocate this assembly Using GM part 14056623 mount this bracket to the left rear cylinder head Install your diaphragm assembly to this bracket NOTE It is easier to install this bracket before manifold is installed on engine MANIFOLD INSTALLATION Before installing the manifold make sure all ports and the valley of the engine are clean Apply a 1 8 bead of 02 sensor safe silicone around the four water ports on
21. s also retained to control the injectors in a batch fire mode In the Edelbrock systems all of the factory sensors are retained and fully functional The compact size was achieved by using extruded aluminum fuel rails with new Magnetti Marelli pico injectors These are half the size of conventional style injectors SPECIAL NOTICE This Edelbrock part has received an Executive Order number E O from the California Air Resources Board C A R B making it legal for street use on pollution controlled motor vehicles in all 50 states To assist you with emissions inspection we have included a silver fan shroud decal to verify that this part is a legal replacement part on the vehicle for which it is cataloged The adhesive backed decal should be affixed to your fan shroud next to the existing emission and engine specification decal Do not cover your original equipment specification decal with the Edelbrock fan shroud decal E 0 decal is shipped with the computer chip lf you have any questions please call our EFI Technical Hotline at 800 416 8628 Option 3 8 00 am 5 00 pm Monday Friday Pacific Standard Time Catalog 3562 3563 3564 3565 2006 Edelbrock Corporation Rev 3 06 Page 4 of 16 Brochure 63 0047 ee a T INSTALLATION PROCEDURE Disconnect negative battery cable Drain coolant Remove air cleaner assembly Label all lines wires and connections with masking tape before disassembly to aid in re assembly Disconnec
22. sitive than a stock TBI Read all instructions before beginning installation Note that fuel tank or bed of pick up must be removed 1987 1991 vehicles with cruise control MUST use Edelbrock throttle cruise kickdown cable bracket 8031 Order from your Edelbrock dealer before beginning installation Catalog 3562 3563 3564 3565 2006 Edelbrock Corporation Rev 3 06 Page 1 of 16 Brochure 63 0047 PERFORMER MULTI POINT EFI KIT CONTENTS Qty Description Qty Description _ 1 Manifold assembly see detail below L 1 3 8 NPT male to 3 8 NPT female 90 Degree elbow Q 1 Installation instructions L 1 3 8 NPT to 1 2 hose brass fitting LL 1 EPROM adapter circuit board 3562 only L 1 2 foot length 15 32 i d vacuum line power brakes L 1 Fuel injector wiring harness L 1 6 length 3 8 fuel line breather line extension L_ 1 Fuel filter adapter fitting filter to 6 AN male with O ring L 1 1 2 NPT to 3 4 hose barb L 1 Return line adapter fitting L 1 36 length 3 4 i d heater hose L 2 6AN straight pushlock fittings Q 1 3 length 5 16 i d high pressure fuel line pump to sending O 1 3 8 i d pushlock heat resistant fuel line 10 foot length unit 1 6AN 45 degree elbow pushlock fitting L 1 2 foot length 5 32 i d vacuum line regulator amp EGR L 1 6AN 90 degree elbow pushlock fitting L 1 5 1 8 i d air cleaner base gasket O 1 Fuel line clamp floor mounted Q 1 12 length 1 4 i d vacuum line MAP D 4 11
23. t transmission mounting bolt Remove fuel line support bracket along with line y k a ti J k a Pa i F i e ee i 1 i So er T a NOTE FOR 1987 1991 MODELS The fuel lines may run down the right side of the bellhousing Both of the connection fittings will be between the transmission and the frame Disconnect both lines being careful of remaining fuel in lines The mounting clamp holding both lines is usually bolted to the rear of the cylinder head Remove mounting bolt or nut and the fuel lines These lines will not be used in new system Remove the two fuel lines from the junction point back to the fuel filter for the inlet line and to the return junction block located just above fuel filter These two lines will not be used in the new system 2006 Edelbrock Corporation Brochure 63 0047 13 INTAKE PREPARATIONS With fuel lines out of the way scrape remaining intake gaskets off of cylinder heads and scrape both end seals clean With surfaces clean install intake gaskets to cylinder heads Use GM gaskets 10181398 Apply gasket sealant to gaskets on surface facing heads only Glue gaskets in place While gaskets set up place the new manifold next to the old manifold You will need to swap certain parts like the distributor hold down clamp and bolt EGR valve and on some models a vacuum fitting located at the right rear of throttle body pad When re installing the EGR valve on the new manifold n
24. t all throttle cables and accessories disconnect all vacuum lines to throttle body Disconnect both fuel lines at rear of throttle body Be careful of line pressure Remove 3 throttle body mounting bolts and remove throttle body Remove top radiator hose remove thermostat housing and thermostat NOTE Ground wires may be located on thermostat mounting bolt It is important to note the location of all ground wires so they can be put back exactly as they were It is a good idea to replace your old thermostat at this time For proper ECM operation it must be the correct temperature usually 195 F check manufacturer s specifications Remove the water pump bypass hose located under the thermostat on front of the manifold Looking at the front of the engine directly to the left of the water pump bypass is the coolant temperature sending unit Disconnect the electric connection remove the sending unit and set aside It is better to remove sensor at this time to avoid damage upon manifold removal The sensor will be re used in the new manifold a Sensor ra Disconnect vacuum fitting for power brake booster from intake manifold Remove heater hose connection from the manifold most will be located at the right rear of the manifold Catalog 3562 3563 3564 3565 Rev 3 06 Page 5 of 16 The electronic vacuum regulator valve is mounted on the third bolt from the front on the right side of the manifold When you remove the br
25. t of the fuel regulator Push 8 connectors onto injectors until they snap on easily The old TBI injector harness has two plugs which go to your old injector assembly Just below the old plugs is a black grommet Lay the old injector harness over the new harness and determine the length of the old wire harness needed to splice into the new harness NOTE Usually the cut will be above the black grommet of the old wire loom 2006 Edelbrock Corporation Brochure 63 0047 23 Pull rubber grommet off of wires Force silicone oxygen sensor safe through these four holes filling them with silicone Install the grommet on air valve in groove to prevent dirt from entering the system ELECTRICAL CONNECTION Separate four wires cut previously out of the factory loom These will be used to mate with the corresponding butt connectors green to green blue to blue and the two pink wires go to either connector on some vehicles pink to pink and pink to white Use Stripping tool to strip end of the wires back 1 4 After sticking stripped end into connector crimp connector onto wire using a Crimping tool Tug on wire slightly after crimping to make sure you have a good connection After crimping all four connectors take heat gun or cigarette lighter be careful not to burn wires to heat the ends of the connectors They will shrink down around the wires and ensure a tight connection After cooling slide all wires into black sleeve
26. the engine Apply a 1 4 bead of silicone on the two end seal areas of the engine block Install the intake manifold onto the engine be careful to set it down as straight as possible Do not set down and Slide into place Install your stock intake manifold bolts in the same locations that they were removed from The bolts with studs need to be in certain holes for the brackets If your vehicle has the cast iron base for the bracket which came off the rear of the alternator and idler pulley you will need to install it at this time Note Some grinding on the bracket ears and on the rear of the bracket where it makes the bend may be required It is important to make sure the bracket sets onto the manifold squarely to avoid damage to the bracket and manifold 2006 Edelbrock Corporation Brochure 63 0047 Tighten the manifold bolts following the tightening sequence shown below Torque to 25 ft Ibs Install the distributor in the engine Using your marks as a reference snug down distributor clamp NOTE Final timing will be adjusted after engine start up Install cap and re install plug wires in the correct location using your marks as a reference Install ignition coil NOTE We provide four bases for the two different coil styles On early models 1987 1990 you will use the two coil bosses towards the rear of the manifold For the later model style coils you will use the two bosses towards the front of the manifol
27. ver to gently pry around strainer and it will pop off Carefully slide the factory fuel pump out of the assembly Install the new fuel pump supplied in the kit into this assembly 28 FUEL PUMP ASSEMBLY With fuel pump assembly on bench loosen and slide up the lower plastic clamp on top of fuel pump Now disconnect electrical connection On the bottom of the fuel pump there is a fuel strainer sock remove the bottom strainer sock after marking it SO you can re assemble in the original orientation ALTERNATE PROCEDURE LOWERING FUEL TANK Suburbans or trucks that you cannot remove the bed require removal of the fuel tank s The fuel tank must be lowered from beneath the vehicle First drain the fuel then disconnect the ground wire and the weather pack electrical connector Then disconnect gas fill hose and vent hose Let the tank drop enough to gain access to the fuel lines then disconnect fuel lines and remove tank from vehicle Most tanks have two mounting straps which must be removed Gas tank mounting straps Catalog 3562 3563 3564 3565 2006 Edelbrock Corporation Rev 3 06 Page 13 of 16 Brochure 63 0047 Note The fuel line will be a very tight fit over the 3 8 tubing It may be necessary to lube the tubing with some spray lubricant to ease hose installation Slip the 5 16 clamp over the rubber hose then insert fuel pump barb into hose and secure with 5 16 clamp Be sure there is adequate clearance between the metal c
28. y 1 3 8 x 2 1 8 x 3 1 4 There are three wires in the harness for the Hot Restart Fuel Module a pink wire with a black stripe a black wire with a white stripe and a tan wire with a white stripe CAUTION iF THE HOT RESTART FUEL MODULE IS NOT REMOVED IT WILL OVERLOAD AND BURN ON START UP CAUSING SMOKE AND POSSIBLE FIRE HAZARD NEW COMPUTER CHIP INSTALLATION IMPORTANT NOTE COMPUTER CHIP MUST BE ORDERED BEFORE BEGINNING INSTALLATION Open glove box and remove four screws mounting the inner tray Remove glove box tray On the ECM you will find the service number and the broadcast code Both are needed in order to make a new calibration chip for your particular vehicle This should be done well before installation to allow enough time for the new chip to arrive Use the chip order card enclosed with these instructions After removing two screws and cover from ECM remove old chip by pressing down on the two outside retaining clips 2006 Edelbrock Corporation Brochure 63 0047 Retaining _ Clips iims i bhi LECZE NELI i y Patni This installation uses a piggyback chip adapter Push your new computer chip into the adapter then install these two parts into ECM There is an alignment lug so that they only fit one way Be careful not to bend any pins Put plate back on and re install ECM in the vehicle NOTE Early models do not require the adapter the chip simply replaces the stock chip p Original Cal
29. y removing the glove box liner This requires removing four 4 small hex head screws and pulling out the liner The ECM sits vertically in a plastic cradle on the far right side of the dash with the connectors facing to the rear 2 The Broadcast Code is stamped on a white paper label located on the top of the ECM Typical codes for the 5 7L run from AKSM to BDXX increasing alphabetically with later release dates There is a plastic decal on the bottom of the glove compartment with a list of the RPO codes for that vehicle This is a listing of the RPO codes and what they stand for CODE VEHICLE EMISSIONS CODE ENGINE CODE TRANSMISSION CODE REAR AXLE NA1 Under 8600 GVW L03 5 0L TBIV8 MD8 4L60 Auto GU2 273 1 NA4 Over 8600 GVW L05 5 7L TBIV8 M30 4L68E Auto GU3 GW9 2 93 1 NA5 Federal L19 7 4L TBIVE MTI 4L80E Auto a Sasa in MG5 Manual w Deep Low GU6 3 4271 NB2 California CTA 2 73 1 NB8 New York California MY2 Manual 5 Speed GT5 4 101 M20 Manual 4 Speed NM8 Special Fuel Compatible HC4 4 56 1 Catalog 3562 3563 3564 3565 2006 Edelbrock Corporation Rev 3 06 Page 3 of 16 Brochure 63 0047 INSTALLATION INSTRUCTIONS for Performer Multi Point EFI System for 7 4L TBI Equipped Chevrolet GMC Vehicles Catalog 3562 and 3564 for 1987 1990 Model Years Catalog 3563 and 3565 for 1991 1995 Model Years APPLICATION INFORMATION Performer Multi Point EFl Systems are designed for 1987 1990 3562 and 3564 and 1991 1995 3563 and 356
Download Pdf Manuals
Related Search