Home

Blaupunkt RMD 169 Radio User Manual

1. Press the knob 1 the control panel folds down forwards e Slide the card as far as possible to the right and remove from the front Engage the control panel For safety reasons the control panel must always be engaged whilst the vehicle is moving When leaving the vehicle open the control panel and remove the Key Card in order to prevent theft Teaching in a second Key Card replacing the KeyCard An additional KeyCard can be taught in whilst the unit is in operation with the first KeyCard To teach in a second KeyCard e Slide the first KeyCard in and switch the unit on e Press DSC and use A V to select LEARN KC e Press lt lt or gt gt CHANGE appears on the display KeyCard anti theft protection system e Remove the first KeyCard and with CHANGE on the display insert the new KeyCard When READY or LEARN KC appears e Press DSC The unit is now also ready for operation with the new KeyCard A maximum of two KeyCards can be taught In If a third KeyCard is taught in the card which is not employed for the teaching in process of the new card automatically loses its va lidity Displaying the radio passport data You can use the KeyCard supplied to call up the radio passport data such as the unit name type number 7 6 and serial number on the display Refer to Programming with DSC READ KC for the procedure Visual
2. Dallas RMD 169 Texas DJ Operating instructions a Ra TRIP MILT PRI MA oll BLAUPUNKT Bosch Gruppe Option Optional Tilval Optie Opcional Op o Condensed instructions 39 Remote control RC 08 optional 46 IMPONE a aasa 47 Read the following before using MS CIV as een 47 TRANG SAI OVY ens aa 47 Installation 47 Telephone mute u02222420022R nennen 47 ACCESSOTIOS cda 47 Guarani lada 47 International hotline 47 KeyCard anti theft protection SS Mica 48 Switching on the unit ooocconcncncnnnccccc 48 Removing the KeyCard 48 Teaching in a second KeyCard replacing the KeyCard 48 Displaying the radio passport data 49 Visual display for anti theft protection 49 Care of the KeyCard 49 KeyCard lost damaged 49 Teaching in the new KeyCard 49 Selecting the operating mode 50 Enhancing the display legibility 50 Radio operation with RDS 51 AF alternative frequency 51 REG Regional nico 51 Selecting the frequency band 52 38 Station tuning seen ai 52 Paging through the transmission chains FM ORIY ee 52 Changing the memory level FM 53 Storing stations s in 53 Automatically saving the strongest
3. PTY remains on the display as long as PTY is activated sur Im pj PORT FHE TETE AF in EHE E MET Ta BES aiil 12 50 Programme type You can display the last programme type selected and select a different programme type with lt lt gt gt Use the station keys 1 6 to select stored programme types Condition PTY is activated You can select the language in DSC from German English or French refer to Pro gramming with DSC PTY LANG The programme types listed below are avail able The letters in bold are the same as those on the temporary PTY display NEWS CURRENT AFFAIRS INFORMATION SPORT EDUCATE DRAMA CULTURE SCIENCE VARIED POP MUSIC ROCK MUSIC EASY MUSIC LIGHT MUSIC CLASSICS OTHER MUSIC WEATHER FINANCE CHILDREN S PROG SOCIAL AFFAIRS RELIGION PHONE IN TRAVEL LEISURE JAZZ MUSIC COUNTRY MUSIC NATIONAL MUSIC OLDIES MUSIC FOLK MUSIC DOCUMENT 55 ENGLISH Radio operation with RDS Radio Data System Prompting the station for the pro gramme type On menu level 2 e Hold PTY down for approx 2 seconds After the beep the programme type of the station currently being received is displayed If NONE is displayed the station has no PTY code Displaying the selected programme type e Press lt lt or gt gt The last programme type selected is dis played briefly Selecting the programme type a Using the station keys If PT
4. A V Enter the digits press once for one twice for two etc lt lt gt gt Select the insertion point e After entering the correct master code press ENT The new KeyCard is accepted when the unit switches to play Input errors Should the input not be correct CODE ERR appears on the display After three successive incorrect inputs WAIT 1h ap pears on the display The unit remains in Wait mode for one hour e Switch the unit off and on again Repeat the teach in process 49 ENGLISH You can select from the Radio TU MiniDisc MD and CD changer CDC modes MD can be selected only if a MiniDisc is in serted CDC can be selected only if a Blaupunkt A 06 A 072 A 08 or A 05 A 071 or IDC A 09 CD changer is connected and a magazine containing at least one CD is inserted Toggling between operating modes Press TU MD or CDC If TU is pressed again menu level 2 is called up Radio function adjustments can be made on this level Menu level 1 is called up auto matically if no input is made for approx eight seconds 90 The display can be adjusted to your pre ferred viewing angle in order to enhance leg ibility Proceed as follows e Press DSC ANGLE appears on the display e Use the rocker lt lt gt gt to select opti mum legibility for your driving position After selecting the setting e Press DSC The Radio Data System provides FM recep tion w
5. Condensed instructions Press SCA for approx 1 second Preset Scan a beep sounds SCAN appears in the display alternately with the code of the sampled station The stations stored on the station keys and which can be received are sam pled briefly Stopping Radio Scan Preset Scan Press SCA or the seek rocker again b PTY is activated logo appears in reverse video on the display er NIP cl FME utr ar E lo EC Ci IA i 1 2 9H Press SCA the stations transmitting the selected PTY programme type are sampled briefly AF Alternative Frequency in RDS mode If AF appears in reverse video in the display the radio automatically looks for a frequency with better reception for the same station AF on off Select menu level 2 using TU and press AF briefly EXIT To terminate or abort the adjustment process press the key briefly ENT Enter To accept save the adjustments press the key briefly TS Travelstore Press TS to switch from any frequency band to FMT The six strongest sta tions are automatically stored When they have been stored the strongest station is selected and played PTY Programme Type PTY turns the station keys into pro gramme type keys PTY must first appear on the display in reverse video Press PTY if neces Sary A programme type such as NEWS SPORT POP can now be stored and selected with each station key C
6. TRACK 13 a ao Ta sopa EM an TRACK 13 Track number or VIVALDI CD name CD changer mode or CD5T2 CD number and track number CD changer mode MIX Tracks can be played in ran dom order SCA Sample tracks RPT Repeat function for MiniDisc CD changer mode TPM Save and play preferred tracks CLR Clear TPM memory VOL EMT FM I Il T FM memory level or MW LW Frequency band or 00 20 Time time played or 12 50 Time Condensed instructions 41 CDC The ignition is off and LED ON is se Remove the KeyCard following the Switch to CD changer mode only if a lected in the DSC menu default facto procedure in reverse CD changer is fitted ry setting Important read the information under If a CD changer is not fitted AUX is Further information Programming KeyCard anti theft protection system 7 selected Condition AUX ON must be with DSC LED ON OFF 3 selected in the DSC menu 17 Eject mm KeyCard anti theft protection Hold the key for MiniDisc ejection 12 MD system down for approx 2 seconds the Switch to MiniDisc mode The KeyCard must be inserted before MiniDisc is ejected the unit can be operated 13 TU TUNER Switch to radio mode For switching to the FMI FM II TS Travelstore MW and LW memory levels frequency bands Inserting the KeyCard To disengage the control panel press key 1 The control panel fol
7. station with Travelstore 53 Calling up stored stations 53 Sampling stored stations with Presel SCAN a 54 Sampling stations with Radio Scan 54 Changing the sampling time Scan 54 Changing the sensitivity ofthe seek run 54 Toggling between stereo and mono EN seen 54 Automatic bandwidth switching SHARX Es 55 PTY Programme Type 55 Programme type cccceseeeeceesseeeceeeees 55 Traffic programme reception with RDS EON 2222222220220002000020 58 Activating deactivating priority for traffic programmes ooooonccncccnncnnnonnnnnnnnnns 58 Warning tone c cccooccccccnncnnnccnnononononnnnnnnnos 58 Automatic seek run 58 Adjusting the volume for traffic an nouncements and the warning tone 58 MiniDisc mode CD changer mode 59 Inserting a MiniDisc 59 Removing the MiniDisc 59 Activating MiniDisc mode 59 MIDI Ei 59 Activating CD changer mode 60 Selecting the display type 60 Selecting tracks and CDS 60 Repeating tracks and CDS 60 TPM Track Program Memory 61 Miura aid lic 62 SCAN ato 62 Assigning a name to CDs 62 Deleting the CD name TPM store using DSC UPDATE 63 Clock tm ida 64 Set
8. FM sensitivity 0 7 uV at 26 dB signal to noise ratio FM transmission range 20 16 000 Hz MD Transmission range 20 20 000 Hz Subject to modifications AF Alternative Frequency With RDS this function ensures that the best frequency of the current programme which can be received is selected automatically Amplifier Power amplifier for increasing the output power AUD Audio Sound adjustment of basses and trebles adjustment of the right left balance and front rear fader volume ratios BND Band For selection of the frequency band and the memory level CL Clear Return to the previous menu item DSC Direct Software Control DSC can be used to adjust certain factory default settings according to the user s per sonal requirements ENT Enter Press briefly to accept save the adjust ments EON Enhanced Other Network With RDS EON permits the exchange of transmitter information within a transmission chain For example a non traffic programme sta tion can be switched automatically to a traf fic programme station for the duration of a traffic announcement Following the an nouncement the original non traffic an nouncement station is selected again Equalizer Sound control for adjustment of the frequen cy response to the acoustic conditions and personal taste EXIT Press the key briefly to terminate or abort the adjustment process KeyCard Blaupunkt s anti the
9. NDR 2 and plays it as long as the station continues to broadcast POP The unit also switches automatically in CD mode to the station broadcasting the select ed programme type within the transmission chain When the PTY programme is over the unit switches back to the source previously se lected radio or CD Note As already mentioned these functions are not currently available with all RDS stations or ENGLISH Activating deactivating priority for traffic programmes EON is the exchange of station information within a transmission chain Many FM stations transmit up to date traf fic announcements for their broadcasting re gion Stations which transmit traffic announce ments transmit a signal which is recognized and evaluated by your car radio When such a signal is recognized TP Traffic Pro gramme appears in the display In addition some stations transmit no traf fic announcements of their own but offer with RDS EON the facility of receiving traf fic announcements from a traffic programme station within the same transmission chain If priority for traffic announcements is to be activated whilst such a station e g NDR3 is being received TA priority for Traffic Announcements must appear in the dis play When a traffic announcement is broadcast the unit switches automatically to the traffic announcement programme in this case NDR2 The traffic announcement is played af
10. is selected the initial volume is the same as that last selected SCROLL PEAK ON OFF Activate deactivate the dy namic volume level display Appears only in MiniDisc mode If the track name is to run continuously through the display SCROLL ON must be selected Appears only in radio mode If you wish to receive re gional programmes for your broadcast area REG ON must be selected Automatic bandwidth switch ing on the FM band Where the station density is high switch to SHARX ON with lt lt gt gt this largely elimi nates interference from ad jacent stations SHARX ON is the default setting Programming with DSC HICUT Interference driven treble reduction Treble frequen cies are reduced only when interference is present Can be selected from NO HICUT OFF to HICUT 3 strongest treble reduction Decide for yourself which setting is the most pleasant FM AM SENS Change the sensitivity of the seek run SENS 1 indicates close re ception SENS 6 distant reception Select SENS 1 if you wish to receive strong stations in the near range select SENS 6 if you also wish to receive weaker distant sta tions STEREO MONO Toggle lt lt gt gt The display indicates the se lected state briefly STEREO is selected auto matically when the unit is switched on AMP DELAY Energization delay of exter CDC NAME CLOCKSET nal amplifiers DLAY OFF
11. the fundamen tal tone range of the music Reproduction must not be come too faint Tonal response too weak Avoid a sharp tonal response Loud hissing impairs the quali ty 6 ENGLISH The car radio offers the facility to adjust cer tain settings and functions to your require ments and to store these changes with the aid of DSC Direct Software Control The default settings are selected at the fac tory An overview of the factory default settings is provided below for future reference To alter a programming setting e Press DSC Select and adjust the functions described below by means of the rocker and the ENT key The status of adjustment is shown on the display A V Select function lt lt gt gt Adjust call up value 68 ANGLE DIM DAY DIM NIGHT TA VOL ON VOL Adjust the display to your own viewing angle Select the display brightness for daylight Stages 1 9 Select the display brightness for darkness Stages 1 9 The brightness is switched over automatically by the headlights REG Adjust the volume of traffic announcements and the warning signal from O 66 Traffic announcements are played at this volume if the standard volume is lower If the standard volume is greater than TA VOL traffic announcements are played at the standard volume SHARX Select the initial volume Use lt lt gt gt to select the de sired initial volume If LAST VOL
12. the volume Select CD _ gt gt Up Press briefly SRC Source _ lt lt Down Press briefly Select the operating mode Radio Select track MiniDisc A Up Press briefly CD changer mode ifa CD changer is CUE fast forward audible connected Keep depressed v Down Press twice or more in quick succession Replay track from beginning Press briefly REVIEW fast rewind audible Keep depressed 46 Read the following before using the unit Before using the car radio read the follow ing instructions carefully Traffic safety Traffic safety is of paramount importance Always use your car radio system in a way which enables you to cope with the traffic situation Remember that your vehicle covers 14m a second at a speed of 50 km h In critical situations do not operate the ra dio You must remain able to hear warning sig nals for example from police and fire serv ice vehicles immediately and reliably Keep the volume therefore at a reasonable level whilst driving Installation If you intend to install or modify the system yourself read the installation and connec tion instructions at the end of the operating instructions before doing so Telephone mute If a mobile phone is connected radio and CD sound can be muted automatically when the phone is in use telephone mute PHONE then appears on the display The traffic announcement has priority if TA is activated Pressing the TA ke
13. CA The last track selected continues playing RPT Repeat MiniDisc tracks and in CD changer mode CD tracks and CDs can be re peated Press the RPT key to select the follow ing functions REP TRCK Repeat track REP CD Repeat CD only in CD changer mode RPT OFF Switches off function TPM Track Program Memory For storing and playing preferred tracks in MiniDisc and CD changer mode Up to 30 MiniDiscs can be man aged in MiniDisc mode and 99 CDs in CD changer mode with a maximum of 40 tracks each Refer to the TPM programming section CLR For clearing the TPM memory refer to the Clearing the TPM memory sec tion 5 DPE For activating deactivating the equaliz er and changing the equalizer settings Activating deactivating the equalizer Press DPE until the beep sounds When the equalizer is activated EQ appears in the display Changing the equalizer settings Press DPE briefly Further information on changing the equalizer settings Equalizer settings 6 Rocker Radio mode If the rocker is pressed on menu level 2 menu level 1 is automatically called up A V Station seek A Up V Down lt lt gt gt Up down in steps on FM only when AF and PTY are deactivated On FM only lt lt gt gt Page through the transmission chains when AF is activated and PTY deactivated e g NDR 1 2 3 4 N JOY Condensed instructions MiniDisc
14. P CD Repeat CD only in CD changer mode RPT OFF Deactivate function e Press RPT repeatedly until the desired function is activated MiniDisc mode CD changer mode The track or the CD is played repeatedly until you switch to RPT OFF using RPT TPM Track Program Memory For storing and playing preferred tracks in MiniDisc and CD changer mode Up to 30 MiniDiscs can be managed in MiniDisc mode and 99 CDs in CD changer mode with a maximum of 40 tracks each TPM is ac tive only in the mode in which the track pro gramme was stored MiniDisc or CD chang er mode Storing tracks with TPM A track can be stored only whilst it is being played To store e Hold TPM down for approx 1 second TPM PROG appears on the display This track has been stored Activating deactivating TPM replay Press TPM briefly The activated state is indicated briefly on the display TPM ON OFF TEN Fra E CSc i at His ZH If TPM is shown in reverse video on the display TPM replay is activated All tracks on the MiniDisc or CD which were stored in the operating mode with TPM are played If SCA Scan is activated in addition to TPM only the stored tracks are sampled TPM replay can be switched on only if tracks have been stored using TPM Clearing the TPM memory You can clear tracks stored with TPM TPM tracks can be cleared with CLR only during replay e Activate TPM TPM app
15. SER VOCAL equalizer settings e Press A V to save the selected equal izer setting and return to the DPE main menu e Press DPE or EXIT to save the select ed equalizer setting and to close the DPE main menu To activate deactivate the equalizer hold AUD down for approx 2 seconds This enables you to compare the sound with and without equalizer Equalizer setting Tips on adjusting the equalizer Begin adjustment with the mid range treble and complete it with the bass range Frequency ranges Bass range 30 to 100 Hz Lower mid range 100 to 400 Hz Mid range 400 to 4 000 Hz Treble 4 000 to 20 000 Hz Tonal effect problem Bass response too weak Bass not clean Booming Unpleasant pressure on the ears Sound lacks depth aggressive no stereo effect Response is dull Clarity lacking Instruments lack brilliance Measure Increase the bass with Filter LOW EQ Frequency 50 to 100 Hz Level 4 to 6 dB Reduce the lower mid frequen cies with Filter LOW EQ Frequency 125 to 400 Hz Level Approx 4 dB Reduce the mid frequencies with Filter HIGH EQ Frequency 1 000 to 2 500 Hz Level 4 to 6 dB Increase the treble range with Filter HIGH EQ Frequency Approx 10 kHz Level 2 to 4 dB Note Avoid distortion Raise the level cautiously if the loudspeaker diameter is too small The tonal response may be come too thin and aggressive Pay attention to
16. Y is activated the programme types defined by the factory can be selected by means of the keys ST 1 ST 6 e Press one of the keys 1 6 The selected programme type appears on the display for two seconds To listen to a station broadcasting this programme type e Start the seek run with A V 96 If no station broadcasting the selected pro gramme type is found NO PTY appears briefly on the display and the beep sounds The last station selected is played You can assign a different available pro gramme type to each memory location Refer if necessary to the Saving the pro gramme type section below b Using the seek run rocker lt lt gt gt If PTY is activated you can select a programme type with lt lt gt gt e Press lt lt or gt gt the last programme type selected is displayed for three seconds During this time select the desired programme type with gt gt forwards or lt lt back Press lt lt or gt gt as many times as necessary To listen to a station broadcasting this programme type e Start the seek run with A V If no station broadcasting the selected pro gramme type is found NO PTY appears briefly on the display and the beep sounds The last station selected is played Storing the programme type A programme type is stored on each of the keys ST1 ST6 by the factory You can however store other available pro gramme types PTY m
17. all up PTY programme types using the rocker lt lt gt gt and press the station key to store hold down for approx 2 seconds until the beep sounds TA priority for Traffic Announce ments TP is displayed when a traffic pro gramme station is being received TA is displayed when priority for traf fic programme stations is activated Only traffic programme stations are played Priority on off Press TA Abort traffic announcement Press TA or EXIT MiniDisc and CD changer mode TRACK 13 m F Aa e Hs 2H MIX SCAN RPT repeat and TPM can be selected in MiniDisc and CD changer mode by means of the corre sponding softkeys MIX MiniDisc and CD tracks can be re played in random order You can select the following functions by pressing the MIX key 41 ENGLISH Condensed instructions 42 MIX MD MIX CD Tracks on the MiniDisc or CD in CD changer mode are played in random order In CD changer mode CDs are se lected in numerical order tracks are replayed in random order MIX MAG CD changer mode only All tracks in the magazine are played in random order MIX OFF Switches off function SCA Scan For sampling the tracks briefly in CD changer mode the tracks of all CDs Starting Scan Press SCA The tracks are sampled briefly in ascending order The sam pling time can be adjusted Refer to Programming with DSC SCANTIME Ending Scan Press S
18. and CD changer mode CDC mode Select CD gt gt Up Press briefly lt lt Down Press briefly Select track A Up Press briefly CUE fast forward audible Keep depressed Vv Down Press twice or more in quick succession Replay track from beginning Press briefly REVIEW fast rewind audible Keep depressed MD mode Select track A gt gt Up Press briefly CUE fast forward audible Keep depressed V lt lt Down Press twice or more in quick succession Replay track from beginning Press briefly REVIEW fast rewind audible Keep depressed Further functions of the rocker Further settings available with AUD DSC MODE 7 PTY The settings are available only if the corresponding function is activated 7 DSC Direct Software Control You can adjust programmable default settings using DSC Further information Programming with DSC AUD For adjusting the treble bass balance left right fader front rear and loud ness settings Loudness adjustment of the low volume sounds to the human ear Different treble bass and loudness settings can be stored for the FM AM MD AUX and TA modes Adjustment procedure Select mode Press AUD once BASS and the se lected value appear on the display RNE 4 4 DA nao E BR dl Ei po r Y l S ma E E TT Select from the options using lt lt gt gt Use A v to change the settings The val
19. ation name frequency appear alternately on the display Selecting sampled stations terminating Preset Scan e Press SCA or one of the rocker keys briefly 94 Sampling stations with Radio Scan You can sample briefly the stations which can be received on the selected frequency band Radio Scan can be started only when PTY is deactivated PTY is not lit on the dis play If necessary deactivate PTY on menu level 2 as follows e Press TU and disable PTY using the PTY key Switching on Scan e Press SCA briefly All stations on the frequency band which can be received are sampled briefly in turn SCAN and the flashing station name fre quency appear alternately on the display Selecting a sampled station deactivat ing Scan e Press SCA or one of the rocker keys briefly If a station is not selected Scan is switched off automatically when the seek function has passed through the complete frequency range The station previously selected is played Changing the sampling time Scan The sampling time can be selected between 5 and 30 seconds If you wish to change the duration of the sampling time refer to Programming with DSC SCANTIME Changing the sensitivity of the seek run You can change the sensitivity of the auto matic seek run If lo is displayed seek only recognizes sta tions with good reception low sensitivity If lo is not displayed see
20. ch a name is to be assigned To change a name enter and save other characters overwrite MiniDisc mode CD changer mode Deleting the CD name TPM store using DSC UPDATE The stored names and the TPMs of CDs can be deleted simultaneously by means of DSC Update You can delete the names and TPMs of the inserted CD with CLR DISC You can delete the names and TPMs of all stored CDs with CLR ALL A CD the stored data name and TPM of which are to be deleted must be replayed for this purpose e Press DSC e Press A V repeatedly until UPDATE appears on the display e Use gt gt CLR DISC for selection if you wish to delete the name and TPM of the stored CD Or e Use lt lt CLR ALL for selecting if you wish to delete the names including TPMs of all stored CDs Hold ENT down for approx 1 second DELETING appears briefly on the display The display operation has been completed To return to the DSC menu item UPDATE without deleting CD names and TPMs e Press ENT briefly 63 ENGLISH Displaying the time The unit has an internal clock which is set automatically through RDS for absolute ac curacy A condition for correction by RDS is that an RDS transmitter with CT function CT clock time is being received Automatic correction of the time can be de activated Setting the time a Automatically The time is set automatically when an RDS tran
21. d in nu meric order Selecting MIX functions e Press MIX briefly the display signals briefly the activated state 62 SCAN For brief sampling of the MiniDisc or CD tracks Starting SCAN e Press SCA briefly SCAN appears on the display The tracks are sampled briefly in turn in as cending order Ending SCAN e Press SCA briefly The last track selected continues playing SCAN is also terminated when the rocker MIX RPT DSC AUD TU or CDC are pressed Assigning a name to CDs in CD changer mode only You can assign names to up to 99 CDs in CD changer mode This name e g VIVALDI appears on the display when you have selected the corre sponding display mode using DIS Starting input e Press the DSC key and A V repeated ly until CDC NAME appears on the display e Press lt lt gt gt The first input field flashes e Now select a character using the rock er A V The letters of the alphabet in capitals A Z the numbers 0 9 and special characters ap pear in turn Move to the next underline using the rocker lt lt gt gt and select a character Up to eight characters can be selected in this way Storing terminating the input e Press ENT to store the input If you wish to abort input of this name e Press DSC If you wish to enter a name for another CD e Press the rocker lt lt gt gt and e Use A V to select from the magazine the next CD to whi
22. display for anti theft pro tection Anti theft protection is provided in the form of a flashing LED 5 when the vehicle is parked and the KeyCard removed The following conditions must be met Battery positive and constant battery posi tive are connected as described in the in Stallation instructions The unit is switched off the control panel is open the KeyCard is removed LED ON is selected in the DSC menu default factory setting If necessary refer to Programming with DSC LED Deactivating the flashing LED Select LED OFF in the DSC menu to de activate the flashing LED Care of the KeyCard The KeyCard will function perfectly only if the contacis are kept free of foreign parti cles Avoid touching the contacts directly with your hands If necessary clean the KeyCard contacts using a cotton bud soaked in alcohol KeyCard lost damaged Should you damage or lose the KeyCard for your unit you can teach in a new KeyCard You can purchase the new KeyCard from your dealer You will also require the mas ter code for the unit which can be found in the car radio passport Keep the car radio passport in a safe e place but not in the car Teaching in the new KeyCard e Insert the new KeyCard and engage the control panel e Press ON e Press TU and ST1 within 5 seconds 0000 appears on the display e Using the rocker enter the four digit master code from the car radio pass port
23. ds down Insert the KeyCard with the contact surface facing downwards see dia gram Engage the control panel Slot for MiniDisc When the MiniDisc is inserted in the direction indicated by the arrow with the label facing upwards it is automati cally transported into the operating po For safety reasons the control sition MiniDisc play mode is selected panel must always be engaged automatically whilst the vehicle is moving When leaving the vehicle open the control panel and remove the Key 15 Visual anti theft protection Card in order to prevent theft The following conditions must be met if the LED is to flash as a visible anti theft protection measure The unit is switched off The control panel is open The KeyCard is removed 45 Keys lt lt gt gt A V MD mode Radio mode Select track A gt gt Up Press briefly CUE fast forward audible Keep depressed v lt lt Down Press twice or more in quick succession Replay track from beginning Press briefly REVIEW fast rewind audi ble Keep depressed Station seek A Up v Down lt lt gt gt Up down in steps on FM only when AF is off On FM only lt lt gt gt Page through the transmission chains if AF is on e g NDR 1 2 3 4 N JOY 2 Switching replay on off Press Gl briefly MUTE appears on MiniDisc and CD changer mode the display when the sound is switched V V CDC mode off Adjust
24. e in order to improve legibility Refer to Improving the legi bility of the display if necessary Switching the sound on off Press ON briefly MUTE appears on the display when the sound is switched off To switch the sound back on again turn the volume knob 3 Switching the unit on off using the KeyCard Insert remove the KeyCard to switch the unit on and off Refer also to the description of the KeyCard anti theft system 16 in the condensed instructions Switching on off by the ignition The unit may be connected up such that it is switched on and off by the ve hicle ignition When the ignition is switched off a double beep reminds you to remove the KeyCard before leaving the vehi cle Switching on whilst the ignition is off With the ignition off and the KeyCard inserted proceed as follows to oper ate the unit Press ON when the double beep sounds The unit is switched on The unit switches itself off automatical ly after an hour s use in order to pre vent the vehicle battery from running down 39 ENGLISH Condensed instructions 3 Adjusting the volume Turn the knob to adjust the volume The selected value is shown on the display When switched on the unit plays at the preselected volume ON VOL ON VOL can be changed refer to Programming with DSC ON VOL 4 Softkeys display Softkey key with variable function The functions shown in the display ca
25. ears on the display in re verse video In this case CLR appears below TPM If you wish to delete the current track only e Hold CLR down for approx 2 seconds TRCK CLR appears briefly on the display If you wish to delete all TPM tracks on the MiniDisc or the CD e Hold CLR down for approx 5 seconds MD CLR or DISC CLR appear brief ly on the display in MiniDisc mode and CD changer mode respectively To delete the stored TPM tracks of all CDs in CD changer mode Hold CLR down for approx 8 seconds ALL CLR appears on the display If you wish to delete TPM and CD names simultaneously refer to Deleting CD name TPM store using DSC UPDATE 61 ENGLISH MiniDisc mode CD changer mode MIX MiniDisc and CD tracks can be replayed in random order MIX is activated when MIX appears in reverse video on the display You can select from the following MIX func tions MIX MD MIX CD in CD changer mode Tracks on the MiniDisc or the selected CD are played in random order In CD changer mode the remaining CDs are selected in numeric order MIX applies to the order in which the tracks are played random MIX MAG in CD changer mode only CDC A 08 IDC A 09 All tracks in the mag azine are played in random order CDC A 06 072 The CDs are selected in ran dom order all tracks of the selected CD are then replayed in random order MIX OFF MIX is deactivated CDs are playe
26. ed The parametric filters can be adjusted ex actly without instruments In addition you can select from seven pre programmed equalizer settings which are adjusted for different musical styles Refer to the Selecting pre set sound settings section The steps required for adjustment are de scribed in the table Adjustment instructions The instructions below represent a recom mendation only You can adjust the sound characteristics according to your own per sonal preference We recommend that you use a familiar mu sic MiniDisc for adjustment of the filters The MiniDisc should include tracks with a range of instruments and voice Pure electronic music is not suitable for evaluation purpos es since the original sound is not known Before adjusting the equalizer setthe bass treble balance and fader to 0 This setting is described in the condensed instructions under 8 AUD Now listen to the MiniDisc with which you are familiar Evaluate your impression of the sound ac cording to your taste Now read the Tonal effect problem column in the table and look for solutions under Measure Use the LOW EQ filter for settings in the bass and lower mid range and the HIGH EQ filter for the treble and upper mid range The HIGH EQ and LOW EQ filters can be adjusted in the DPE menu e Press DPE to call up the DPE main menu Adjusting the frequency level e Press A V repeatedl
27. en completed the strongest station ST 1 is selected Stations can also be stored manually on the Travelstore level if required see Storing stations Calling up stored stations You can call up stored stations at the touch of a button FM Call up the stations directly on the selected memory level as follows e Press the keys ST1 ST6 To call up stations on a different memory level e Press NEXT until the desired memory level is displayed then select a stored station with ST1 ST6 NIR 2 FHa TRPTrAr n ELI RES ri at RT j Sn ES Las J MW LW You can call up the stations on the selected frequency band directly e Press the keys ST1 ST6 Calling up stations on the other frequency band e Press NEXT the other frequency band is displayed Then select the stored stations using ST1 ST6 53 ENGLISH Radio operation with RDS Radio Data System Sampling stored stations with Preset Scan You can sample stored stations briefly on all frequency bands and on the selected FM memory level Preset Scan can be started only when PTY is disabled PTY is not lit on the display If necessary disable PTY on menu level 2 Proceed as follows e Press TU and disable PTY using the PTY key Starting Preset Scan e Press SCA for approx 1 second All stored stations on the frequency band which can be received are sampled briefly in turn SCAN and the flashing st
28. er is connected OFF is the de fault factory setting If an external unit is con nected through AUX ON must be selected This function enables you to teach in a second KeyCard Refer to the instructions un der KeyCard anti theft pro tection system Teaching in a second KeyCard The data can be read out from a KeyCard Unit data such as name type number 76 and seri al number are displayed by the KeyCard supplied Should you remove the Key Card during the read proc ess READ KC appears in the display In CD and CD changer mode this function enables the names of CDs to be de leted in order to create space for new CDs Refer to Deleting CD names with DSC UPDATE End DSC programming store settings Press DSC Overview of the factory default settings with DSC ANGLE DIM DAY DIM NIGHT TA VOL ON VOL PEAK ON OFF SCROLL ON OFF REG ON OFF SHARX HICUT FM AM SENS STEREO MONO AMP DELAY CDC NAME CLOCKSET CLK AUTO MAN 12 24H MODE CLK ON OFF BEEP LED SCANTIME PTY LANG AUX LEARN KC READ KC UPDATE 0 9 9 35 LAST VOL ON OFF OFF SHARX ON HICUT 2 SENS 6 STEREO DLAY OFF 0 00 CLK AUTO 24H MODE CLK OFF 3 ON 10 sec DEUTSCH OFF Amplifier 4 x 25 watts sinusoidal to DIN 45 324 at Output power 14 4 V 4 x 40 watts max power Tuner Frequency bands FM 87 5 108 MHz MW 531 1602 kHz LW 153 279 kHz
29. for traffic announcements has been switched on See also RDS TP Traffic Program TP in the display indicates that the radio is tuned into a station which broadcasts traffic information See also RDS TPM Track Program Memory Stores and plays your favourite tracks in CD or changer mode TS Travelstore Automatically stores the stations with the best reception on the station preset buttons Very useful during long journeys Service Nummern Service numbers Num ros du service apres vente Numeri del servizio di assi stenza Servicenummers Telefonnummer for service Numeros de servicio Numero de servi o Deutschland Belgique France Nederland Great Britain Denmark Sverige Norway Suomi Osterreich Greece Cesk republika USA Singapore Slovensko 11 99 Tel 018 050 002 25 025 255 444 014010 70 07 023 565 63 48 018 958 383 66 44 89 83 60 08 750 15 00 66 81 70 00 094 359 91 045 989 90 28 015 762 241 026 130 04 41 800 266 25 28 006 535 054 47 042 175 873 212 Fax 051 214 940 02 025 255 448 014 010 73 20 023 565 63 31 018 958 383 94 44 89 86 44 08 750 18 10 66 81 71 57 094 359 92 36 016 103 93 91 015 769 473 026 130 05 14 08 681 71 88 006 535 053 12 042 175 873 229 Blaupunkt Werke GmbH Bosch Gruppe C K7 VKD 8 622 402 228
30. ft protection system The unit can be operated only with the correct KeyCard MIX Play CDs CD tracks in random order MUTE Switches audio off 71 ENGLISH Glossary Technical Terminology Preset Scan See also SCAN PTY For selection of a desired programme type in FM mode e g sport news Refer also to RDS RDS Radio Data System Service provided by the broadcast stations for improved listening convenience For example the station name is shown in place of the frequency Further RDS functions include AF Alternative Frequency EON Enhanced Other Network Radio Texi REG Regional Programme PTY Programme Type TA Traffic Announcement TP Traffic Programme REG Assign priority to regional programmes REG ON prevents the unit from switching automatically to a different regional pro gramme of the same broadcasting station with better reception Refer also to RDS 12 RPT Repeat Repeat CD tracks Tracks or CDs can be repeated in CD changer mode SCAN Briefly plays the radio stations in your cur rent reception range or the tracks on a CD in CD mode Using Preset Scan you can scan the radio stations stored on the preset buttons Softkey Software key Key with varying functions SRC Source Source switch between radio and CD chang er TA Traffic Announcement priority for traf fic information TA in the display indicates that the priority
31. io automatically looks for the next station If A V is held down at the top or bottom the seek run continues forwards or back wards at higher speed Station seek A Up V Down lt lt gt gt Up down in steps on FM only when AF is deactivated Manual tuning with lt lt gt gt You can tune manually Condition AF and PTY are deactivated the corre sponding symbols are not lit in the display NIR E FMI TA PTY AF b EO DISC N If necessary these functions can be deacti vated on menu level 2 Manual tuning e Press lt lt gt gt the frequency is in creased reduced in steps Hold the lt lt gt gt rocker down to the right or left to change the frequency quickly Paging through the transmis sion chains FM only You can use lt lt gt gt to call up stations from the region in which they can be received If a number of programmes in the station chain can be received you can page through them with gt gt forwards or lt lt backwards e g NDR 1 2 3 4 To start Travelstore for example Press TU menu level 2 is displayed If AF fails to come on Press AF on menu level 2 Radio operation with RDS Radio Data System Changing the memory level FM You can change between memory levels Il and T to store stations and retrieve them again The selected memory level appears on the display e Press NEXT briefly and repeatedly un til the desired memo
32. ith enhanced convenience An increasing number of radio stations now broadcast RDS information supplementary to the programme proper As soon as stations can be recognized the station code appears in some cases with indication of the region e g NDR1 NDS Niedersachsen With RDS the station keys become pro gramme keys You now know exactly what station you are receiving and you can there fore also select the desired station RDS offers you further advantages AF alternative frequency The AF Alternative Frequency function en sures that the best available frequency of the station being received is selected auto matically Switching AF on off During radio mode e Press TU menu level 2 is called up e Press AF briefly This function is active when AF is lit in the display MDF E FHE ARTE ar lo EO DEZ E SC ar ER HENI ge Jk AF then appears in reverse video on the corresponding key DE co FR TAPTY AF b EO DISC N The radio may be muted briefly during the search for the channel with the best recep tion If SEARCH appears on the display when the unit is switched on or when a stored fre quency is called up the unit is automatical ly searching for an alternative frequency SEARCH disappears when an alternative frequency has been found or when the fre quency band has been completely searched If the station can no longer be received with satisfacto
33. k also recognizes stations with poorer reception To adjust the sensitivity refer to Program ming with DSC FM AM Sens Toggling between stereo and mono FM You can toggle between stereo and mono in the DSC menu This can be useful in are as where reception is critical When the unit is switched on stereo is selected automati cally Radio operation with RDS Radio Data System When reception is poor the unit switches smoothly to mono If you wish to switch to mono refer to Pro gramming with DSC STEREO MONO The state selected appears briefly on the display Automatic bandwidth switching SHARX You can activate automatic bandwidth switching on the FM band by means of the SHARX function in the DSC menu This is very useful when a number of stations are close together Interference from strong adjacent stations is largely eliminated when SHARX ON is selected factory default setting If necessary refer to Programming with DSC SHARX PTY Programme Type This is an RDS service which is being im plemented progressively by the radio sta tions The service enables FM stations to be selected according to a specific pro gramme content After selecting the pro gramme type you can select the stations using seek or Scan Activating deactivating PTY e Press PTY When the function is activated the last pro gramme type selected e g SPORT is dis played briefly
34. n be selected Radio mode In radio mode use TU to toggle be tween menu level 1 and menu level 2 The system automatically returns to menu level 1 when no key has been pressed for eight seconds 40 Menu level 1 Station keys and memory levels PITA i Pra T a n a ca sH NEXT FM Switch between the memory levels FM 1 FM II FM T NEXT AM MW LW Switch between the MW and LW fre quency bands ST1 ST6 ST1 ST6 can be used on this menu level to store radio stations on the FM levels I Il and T You can store six stations each on the MW and LW bands Store station hold one of the station keys ST1 ST6 down until the pro gramme can be heard again beep Call up station select the frequency band On FM select the memory level using NEXT and press the appropriate station key briefly Menu level 2 Adjusting radio functions PITO 5 nor 14 TIF E DD ve a z 12 50 de e NEXT FM Switch between the memory levels FM FM II FM T NEXT AM MW LW Switch between the MW and LW fre quency bands BND Select the frequency band and memo ry level FM I FM Il FM T MW LW SCA Scan a PTY is deactivated logo is lit normally not in reverse video Press SCA Radio Scan briefly SCAN appears in the display alter nately with the code of the sampled station All stations on the frequency band which can be received are sam pled briefly
35. n a replacement from a specialist dealer If you are using two KeyCards the settings are taken from the first KeyCard You can customize the following functions Station key assignment bass treble bal ance and fader settings loudness TA traf fic announcement volume beep volume LOW EQ HIGH EQ The last state selected such as frequency band station setting TA priority AF REG ON OFF SCAN TIME seek run sensitivity ON VOL volume at switch on SHARX is also saved Your selected settings are therefore select ed automatically when you insert your Key Card Switching on the unit e Switch on the unit with ON To insert the KeyCard disengage the con trol panel Press the knob 1 the control panel folds down forwards 48 e Insert the KeyCard with the contact surface downwards as shown in the diagram Arrow 1 e Slide the card in the direction of the ar row 2 and engage the control panel Arrow 3 The car radio is ready for use Should a KeyCard other than that belong ing to the unit be inserted CARD ERP ap pears on the display The unit switches itself off after approx 10 seconds Should a card other than a KeyCard be in serted e g a phonecard or credit card WRONG KC is displayed for approx 2 seconds In this case remove the card and insert a KeyCard for the unit e Press ON to switch on the unit Removing the KeyCard Disengage the control panel as follows
36. nd side and engage Removing the MiniDisc With the control panel disengaged hold the Eject key arrow down for ap prox 1 second The MiniDisc is ejected Do not obstruct or assist automatic inser tion or ejection of the MiniDisc as the mech anism may otherwise be damaged If the MiniDisc is not removed it is drawn in again automatically after approx 30 sec onds For safety reasons the control panel must always be engaged whilst the vehicle is moving Activating MiniDisc mode A MiniDisc is inserted DISC IN appears on the display e Press MD TRACK 13 ay o i GC Es a TH L EL a O LL w mv MMe ZEN ra MD text The names of the MD and individual tracks can be displayed if they are stored on the MiniDisc Activating deactivating MD text e Hold the DIS key down until a beep sounds The text MDTXT ON or NO MDTXT is displayed Displaying the MD text e Press MD briefly Condition SCROLL is set to OFF in the DSC menu SCROLL ON causes the name to run across the display Refer to the Programming with DSC SCROLL section 99 MiniDisc mode CD changer mode Activating CD changer mode A magazine containing at least one CD must be inserted e Press CDC CD changer functions such as CD and track number name time played appear in the display Selecting the display type You can switch the display type over in MiniDisc and CD changer
37. replay mode TRACK 13 ay ME Ene amp TPM me MMe ZEN a Press DIS repeatedly until the desired display type is selected CDC mode CD 10 CD number TRACK 13 Track number 14 34 Time 00 20 Time played VIVALDI CD name 60 MD mode TRACK 13 Track number 14 34 Time 00 20 Time played Key held down Activate deactivate MD text The name of the CD can be displayed only if a name has been entered Refer to the Assigning names to CDs sec tion below Selecting tracks and CDs CDs only in CD changer mode You can select tracks or parts of tracks and in CD changer mode CDs conveniently us ing the rocker Selecting a CD CD changer mode only lt lt gt gt Select CD CD changer mode only Up Press briefly Down Press briefly gt gt lt lt Selecting a track A v Select track A Up Press briefly CUE fast forward audible Keep depressed Down Press twice or more in quick succession Replay track from beginning Press briefly REVIEW fast rewind audible Keep depressed The rocker acts as a sequence switch pressing it repeatedly causes several CDs or tracks to be skipped Repeating tracks and CDs CDs only in CD changer mode You can repeat a track or in CD changer mode a CD continually You can select the following functions using the RPT key REP TRCK Repeat track RE
38. ry level appears on the display wr ml E FHE TAPTY AE DH a E E coa M A F Lamas Storing stations You can store six stations on the FM band on each memory level I Il T using the sta tion keys ST1 ST6 You can also store six stations each on the MW and LW bands Proceed as follows e Press TU menu level 2 is displayed e Select the frequency band using BND Select a station using the rocker auto matically A V or manually lt lt gt gt Press the desired station key repeat edly until the programme can be heard again after it has been muted approx 2 seconds and a beep is heard The station is now stored Note Should you store a station which has already been stored the corresponding station key and the memory level flash briefly if a differ ent memory level is called up Automatically saving the strong est station with Travelstore You can store the six strongest FM stations in the current reception region automatical ly in the order of field strength This function is particularly useful on long journeys Pro ceed as follows e Press TU menu level 2 is displayed e Press TS briefly T S TORE flashes on the display The six strongest FM stations are automat ically stored on the T Travelstore memo ry level If fewer than six stations can be re ceived four lines appear through the mem ory locations which are not occupied When the procedure has be
39. ry quality e Select a different station REG Regional At certain times the broadcast stations transmit different programme content ac cording to the region For example German Radio 1 serves the northern regions Schleswig Holstein Hamburg and Lower Saxony and at certain times broadcasts re gional programmes which differ in content If you are listening to a regional programme and wish to continue to receive it switch to REG ON in the DSC menu If you are leav ing the region in which the regional pro gramme can be received or if you wish to enjoy the full RDS service switch to REG OFP Switching REG over e Press the DSC key and A V repeated ly until REG ON OFF appears in the display e Press lt lt gt gt to toggle between REG ON and REG OFF e Press DSC to leave the DSC menu and save the settings 51 ENGLISH Radio operation with RDS Radio Data System Selecting the frequency band You can select from the following frequen cy bands FM 87 5 108 MHz MW 531 1602 kHz and LW 153 279 kHz as follows Press TU menu level 2 is displayed wr fale d FME TAPTY AF DHL o EO ES H PLA E ul IA a a oF mul A A a Menu level 2 e Select the frequency band by pressing BND repeatedly until the desired fre quency band appears The sequence is FM I FM Il FMT MW LW 92 Station tuning Station seek A V e Press A V the rad
40. signifies no energization de lay DLAY 1 to DLAY 4 sig nify the energization delay in seconds Displayed only in CD chang er mode You can use this function to assign any desired name to the CDs Refer to Assign ing names to CDs Manual adjustment of the time Use lt lt gt gt to select hours minutes The flashing range can be adjusted with A V Press ENT briefly to save after completing the setting Refer also to CLOCK time CLK AUTO MAN For activating deactivating automatic hours correction Refer also to CLOCK time hours correction 12 24H MODE Select the time display 12 hour or 24 hour CLK ON OFF The time can be displayed BEEP with the ignition on and the unit switched off Select CLK ON in this case Confirmation signal for func tions which require a key to be held down for approx 1 second The volume can be selected from O to 9 0 off LED ON OFF You can select between SCANTIME LED ON and LED OFF When LED ON is selected the ON knob flashes to provide additional security when the unit is switched off and the KeyCard removed This setting defines the sampling time 5 30 sec onds for radio broadcasts and CD tracks 69 ENGLISH Programming with DSC PTY LANG Select the language for pro gramme type codes Ger man English or French AUX ON OFFThis menu item does not ap LEARN KC READ KC 70 pear when a CD chang
41. smitter with the CT clock time function is being received b Manually by means of DSC CLOCKSET Press DSC briefly CLOCKSET ap pears on the display Press lt lt gt gt to set the hours min utes The flashing area can be modi fied with A V After correcting the time press ENT briefly to save the setting 64 The time can be displayed in radio and CD mode Radio mode The display can be toggled between time and frequency band incl memory level in the case of FM as follows e Press DIS for approx 2 seconds MiniDisc CD changer mode You can select from three different display modes Track number time Track number time played CD name track number CD changer mode only To toggle e Press DIS briefly Correcting the time following an interruption to the power supply If the unit has been isolated from the supply voltage for a longer period 0 00 is dis played when the power is reconnected The time is corrected automatically by RDS CT but can also be adjusted manually The time need be adjusted manually only if an RDS station with CT clock time is not being received If you wish to correct the time manually re fer to Programming with DSC CLOCK SET Deactivating hours adjustment Correction of the hours can be deactivated by CLK MAN CLK AUTO in the DSC menu The minutes continue to be corrected This is useful if you wish to displa
42. ter which the unit switches back to the pro gramme NDR3 previously selected 58 TA appears on the display when traffic pro gramme priority is activated Activating deactivating priority e Radio mode Press the TU key again to call up the function menu not nec essary in MD CDC mode e Press the TA softkey S6 The function menu of the audio source is called up automatically during a traffic an nouncement If the TA softkey is pressed during a traffic announcement priority is deactivated only for the duration of this par ticular announcement The unit switches back to the previous state Priority remains active for further traffic announcements A number of keys have no function during a traffic announcement Warning tone Should you leave the broadcast range of a selected traffic announcement programme a beep sounds as a warning at intervals of approx 30 seconds Pressing a station key on which a station without a TP signal is stored also causes a warning tone to sound Deactivating the warning tone Select a different station with the traffic an nouncement service e Press the rocker or e a station key on which a traffic an nouncement programme is stored or Deactivate traffic programme station priority e Press the TA softkey S6 Automatic seek run If you are listening to MDs or CDs and you leave the broadcast range of the selected traffic programme station the radio automat icall
43. ting the Mecano 64 Displaying the time ooccccccconccncnnnnnnnnnno 64 Correcting the time following an interruption to the power supply 64 Deactivating hours adjustment 64 Equalizer setting 65 Adjustment instructions 65 Tips on adjusting the equalizer 67 Programming with DSC 68 Overview of the factory default settings with DSC occcccccccccccccnnccconcnnnos 70 Technical data 71 Glossary sahen 71 Installation and connection instructions 289 1 Disengaging the fold down control panel Disengage the control panel to insert or remove the KeyCard and MiniDisc To disengage the control panel press knob 1 the control panel folds down The control panel cannot be removed nor should it be used a shelf To re engage the control panel push it back into its original position Arrow 3 For safety reasons the control panel must always be engaged whilst the vehicle is moving When leaving the vehicle open the control panel and remove the Key Card in order to prevent theft 2 ON om Switching on the unit Insert the KeyCard and press ON briefly The unit is switched on in the last op erating mode selected and with the previously selected volume Switching off the unit Press ON for approx 1 second The display can be adjusted for the de sired viewing angl
44. ues selected are shown on the display The last setting selected is stored automatically Particular feature of loudness The values can be selected between LOUD 6 and LOUD OFF by means of the rocker A V Leaving AUD Press EXIT If no change is made within eight sec onds AUD is automatically switched off 43 Condensed instructions 9 DIS 44 CD changer mode Press DIS briefly CD number track number time CD number track number time Selecting various display modes Radio mode Press DIS briefly played Name of the selected station CD name track number Currently selected frequency PTY code Display A condition is that an RDS station can be received with an adequate field strength J Bt p P NIP 2 TANEET OE HET pr AF lo EO DISC IN Bo DEH F z p NDR2 Station name F FM Frequency band SS I II T Memory level I Il or Travel store Press DIS for approx two seconds TP TA TP Traffic Programme traf Toggle display between time and wavelength incl memory level in the fic programme station is be ing received case of FM TA Priority for traffic pro gramme station is activated MiniDisc mode PTY Programme type is activated AF Alternative frequency with Press DIS briefly oz Track number time lo Seek sensitivity can be se Track number time played lected with DSC EQ Equalizer is activated DISC IN MiniDisc is inserted
45. ust be displayed before you can store a different programme type If necessary activate PTY using the PTY key e Select the programme type with lt lt gt gt and hold the desired key ST1 ST6 down until the beep sounds The selected programme type can be called up by means of this key when PTY is acti vated PTY appears on the display Sampling stations with PTY SCAN Condition PTY must be displayed e Press SCA The stations with this programme type which can be received are sampled briefly Deactivating PTY SCAN e Press SCA or the seek rocker again Following a frequency seek run PTY SCAN is automatically deactivated Radio operation with RDS Radio Data System PTY priority Situation PTY is activated the logo appears on the display No station broadcasting the selected pro gramme type can be received at this time by seek or by Scan The unit switches back to the previous sta tion As soon as a station broadcasting the se lected programme type can be received within the station chain the unit switches to this station in radio mode for the duration of the programme Example Previous station NDR 3 PTY on the display POP selected Seek run started No station with PTY POP found Display shows NO PTY and Switches back to NDR 3 automatically NDR 2 is broadcasting PTY POP Unit switches within the station chain to
46. y causes a traffic announcement to be interrupted Accessories Only use accessories and spare parts ap proved by Blaupunkt The following Blaupunkt products can be used with this unit Remote control RC 08 optional Infrared remote control RC 08 permits operation of the chief functions from the steering wheel Amplifiers All Blaupunkt amplifiers CD changers The following CD changers can be fitted di rectly CDC A 06 A 072 A 08 IDC A 09 CD changers A 05 and A 071 can be fitted by means of the 7 607 889 093 adapter cable The IDC A 09 is included with the Taxas Du Navigation The TravelPilot DX N can be fitted for dy namic navigation Guarantee The unit is guaranteed in accordance with the statutory provisions of the country in which it was purchased Irrespective of the statutory provisions Blau punkt guarantees the unit for twelve months Should you have any questions concerning the guarantee please consult your dealer Your receipt suffices as proof of guarantee International hotline Do you have any questions regarding oper ation of the unit or do you require further information Simply give us a call The international hotline and fax numbers can be found on the last page of these in structions i 47 ENGLISH One KeyCard is supplied with the unit The car radio can however also be operat ed with a second KeyCard Should you lose or damage a KeyCard you can obtai
47. y looks for a new traffic programme sta tion If a traffic announcement station is not found within approx 30 seconds of the start of the seek run a beep sounds as warning at intervals of 30 seconds To switch off the warning tone follow the procedure de scribed above Adjusting the volume for traffic announcements and the warning tone This volume is set in the factory as a de fault You can however change it by means of DSC refer to Programming with DSC TA VOL This unit enables you to play MiniDiscs CDs can also be played with the aid of a Blau punkt CDC A 06 A 072 A 08 A 05 A 071 or IDC A 09 CD changer These CD changers are available from your dealer The IDC A 09 is included with the Taxas DJ Note Only use standard circular 12 cm diameter CDs in the CD changer 8 cm diameter CDs or CDs with different shapes e g of a butterfly or beer glass are not suitable for playing Such CDs present a serious risk of damage to the CD and to the drive We can accept no liability for damage aris ing from the use of unsuitable CDs Inserting a MiniDisc e Switch on the unit and disengage the control panel with knob 1 The control panel drops forward e Insert the MiniDisc with the label facing upwards in the direction indicated by the arrow Do not use force The MiniDisc is automatically transported to the playing position The MiniDisc is played Fold the control panel up on the left ha
48. y the time of a different time zone for example If necessary e Press DSC briefly and e press A V repeatedly until CLK MAN CLK AUTO is displayed To deactivate hours correction select lt lt gt gt CLK MAN Equalizer setting The sound in the vehicle is influenced deci sively by the acoustic characteristics of the passenger compartment substantially more than by the characteristics of the loudspeak ers The position and installation of the loud speakers and the volume to the rear for ex ample of the door or parcel shelf are how ever also important Even when suitable loudspeakers have been selected and installed properly reso nances in the passenger compartment may have a detrimental effect upon the sound This can result in the bass frequencies booming or being absent mid frequencies encroaching excessively musical instru ments or voices being strongly distorted or the sound generally being muffled The subjective sound impression can be improved considerably by suppression or amplification of certain frequency ranges by the car radio This unit is equipped with two parametric fil ters The first filter LOW EQ can be ad justed from 32 to 500 Hz the second HIGH EQ from 630 to 10 000 Hz In this case parametric means that one frequency can be increased or reduced for each of the two filters 10 to 20 dB The bandwidth qual ity of the two filters can also be adjust
49. y until HIGH EQ or LOW EQ appear in the display e Press lt lt or gt gt once or several times to select the frequency e Press A V once or several times to adjust the level GAIN 8 GAIN 8 e Press lt lt or gt gt once or several times to select a different frequency and to adjust the level accordingly e Press DPE or EXIT to save the select ed level and to return to the DPE main menu e Press DPE or EXIT again to close the DPE menu 65 ENGLISH Equalizer setting Selecting a quality factor for the bass or mid range e Press A V repeatedly until LO Q FAC or HI Q FAC appear in the dis play e Press lt lt or gt gt once or several times in order to set the quality factor Q FACT 1 to Q FACT 3 e Press A V to save the selected factor and return to the DPE main menu or e Press DPE or EXIT to save the select ed factor and to close the DPE main menu Selecting the preset sound setting Selecting a preset influences the equalizer and sound settings of the unit Each select ed preset can be adjusted manually When a different preset is selected however the factory default setting is restored Your per sonal sound settings for BASS TREBLE EQ and LD are stored in the USER preset mode To call up the presets e Press A V repeatedly until PRESET appears on the display 66 e Press lt lt or gt gt once or several times to select the U

Blaupunkt RMD 169 Radio User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents