Bissell 1697 Vacuum Cleaner User Manual
Contents
1. Be sure caring Tool Snap Together to thoroughly rinse out any remaining Fiber Cleansing Formula to prevent slippery linoleum vinyl and tile floors Use BISSELL Hard Floor Solutions in the SmartMix tank e Check ReadyTools dial it should be set on Floor Cleaning Set the SmartMix setting to normal Plug into a proper outlet and turn Power Switch ON Bare Floor Cleaning Technique Slowly move the machine nozzle with Bare Floor Tool forward and back over soiled surface one time while pressing the trigger Caution Do not over wet e Repeat the motion without pressing the trigger using the Bare Floor Tool to squeegee and suction up the dirty water e Repeat steps 1 and 2 backing along the exit path Allow about 30 minutes for the floor to dry completely When the cleaning job is complete refer to the Maintenance Storage section on page 12 To remove Bare Floor Tool gently bend long tab right side outward and pull tool down away from nozzle Rinse thoroughly dry and store ug310 5921_1697_105 indd 11 Keep plenty of genuine BISSELL Fiber Cleansing Formula on hand so you can clean whenever it fits your schedule Always use genuine BISSELL deep cleaning formulas Non BISSELL cleaning solutions may harm the machine and void the warranty 2 2 05 10 58 44 7 Maintenance Storage ug310 5921_1697_105 indd 12 Ip SmartMix tank may be Qum Power s2. follow SmartMix instructions on page 6 Q Clean Out Filter follow Steps under Maintenance Storage on page 12 Turn power OFF remove tank and check gasket on tank bottom reseat tank Q Turn power OFF after 1 minute turn ON and depress Spray trigger 2 2105 10 58 45 AM ug310 5921_1697_105 indd 14 Troubleshooting Continued Insert Screwdriver Blade Here Reduced Spray Or No Spray Continued Possible Causes Remedies The Pump Belt may be broken Q Turn the machine OFF and unplug from the outlet To check if a Pump Belt has_broken you will need a flat head screwdriver Insert the blade end into the lower slot of the Belt Access door to release the lower snap If necessary insert the blade end into the upper slot to release the upper snap Examine the belt for breakage You should be able to see the Pump Belt looped around the motor shaft If it is broken or missing please refer to Replacement Parts on page 15 before calling Consumer Services Complete installation instructions will accompany the replacement belt PowerSteamer is not picking up solution Possible Causes Remedies ReadyTools Dial may be at the Set ReadyTools Dial to either FLOOR wrong setting for cleaning job CLEANING or TOOLS PRETREAT Nozzle Window may not be properly attached Make sure the two tabs on the back of the Floor Nozzle Window are inserted through the mating slots in the ma
3. After cleaning you may want to turn the SmartMix to Water Only to give your carpeting a final rinse This will insure thorough removal of embedded dirt loosened by the Fiber Cleansing Formula BISSELL Fiber Cleansing Formula contains an anti resoiling agent that helps your carpets repel dirt and keeps them looking clean longer If you choose to rinse your carpets you may want to apply BISSELL Carpet Protector after rinsing Follow the label instructions When the cleaning job is complete refer to the Maintenance Storage section on page 12 2 2105 10 58 37 AM Cleaning Fluid Section Keep plenty of genuine BISSELL Fiber Cleansing Formula on hand so you can clean and protect whenever it fits your schedule Always use genuine BISSELL deep cleaning formulas Y fit leansing as BISSELL Fiber A WARNING Cleansing To Reduce the Risk of Fire and Electric Shock Formula with due to internal component damage use only ee BISSELL cleaning fluids intended for use with item 0710 the deep cleaner gt How To Clean Upholstery and Small Areas Important Check Upholstery Tags Check manufacturers tag before cleaning W or WS on the tag BISSELL Pet Odor means you can use your PowerSteamer Pro If the tag is coded with X or S with a diagonal strike through or says Dry Clean Only do not proceed Do not use on velvet or silk If manufacturer s tag is missing or not coded
4. Do not allow to be used as a toy Do not use for any purpose other than described in this User s Guide Do not operate the appliance unless the belt door is securely assembled in the location provided Use only manufacturer s recommended attachments Use only cleaning products formulated by BISSELL for use in this appliance to prevent internal component damage See cleaning fluid section of this manual W Keep openings free of dust lint hair etc ug310 5921 1697 105 indd 3 E Be extra careful when cleaning stairs Close attention is necessary when used by or near children Turn off all controls before unplugging WARNING The Power Cord on this product contains lead a chemical known to the State of California to cause birth defects or other reproductive harm WASH HANDS AFTER HANDLING SAVE THESE INSTRUCTIONS THIS MODEL IS FOR HOUSEHOLD USE ONLY Commercial use of this unit voids the manufacturer s warranty GROUNDING INSTRUCTIONS This appliance must be connected to a grounded wiring system If it should malfunction or break down grounding provides a safe path of least resistance for electrical current reducing the risk of electrical shock The cord for this appliance has an equipment grounding conductor and a grounding plug It must only be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances Grounded Outlets Gr
5. ED TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE 2005 BISSELL Homecare Inc Grand Rapids Michigan Some states do not allow limitations on how long an implied warranty lasts All rights reserved Printed in USA so the above limitation may Part Number 310 5921 Rev 2 05 Visit our website at www bissell com Scotchgard a trademark of 3M 2 2105 10 58 48 AM
6. RC n N 215 9155 Tough Stain Brush 015 9043 Tank Assembly Complete C 015 4439 Tank Lid Assembly 015 9041 Tank Bottom 4 3 213 0213 Baffle with Red Float ED 215 0628 Replacement Pump w Belt with instructions 213 3501 Lint Screen 015 0621 Replacement Brush Belt 7 with instructions 214 9131 Bare Floor Tool 0710 48 oz BISSELL Fiber Cleansing Formula 10 with Scotchgard 0400 22 oz BISSELL Tough Stain PreCleaner ug310 5921_1697_105 indd 15 2 2 05 10 58 46 AM ug310 5921_1697_105 indd 16 About Your Warranty This warranty gives you specific legal rights and you may also have other rights which may vary from state to state If you need additional instruction regarding this warranty or have questions regarding what it may cover please contact BISSELL Consumer Services by E mail telephone or regular mail as described below Limited One Year Warranty Subject to the EXCEPTIONS AND EXCLUSIONS identified below upon receipt of the product BISSELL Homecare Inc will repair or replace with new or remanufactured components or products at BISSELL s option free of charge from the date of purchase by the original purchaser for one year any defective or malfunctioning part See information below on If your BISSELL product should require service This warranty applies to product used for personal and not commercial or rental service This warranty does not apply to fans or rout
7. check with your furniture dealer Formula with Scotchgard Protection item 0730 27 Check for colorfastness inconspicuous place e If possible check upholstery stuffing Colored stuffing may bleed through fabric when wet Plan activities to give upholstery time to dry Q Vacuum thoroughly to pick up loose debris and pet hair Use a vacuum with a brush attachment and a crevice tool to clean in fabric folds and tufts Machine Preparation the machine following the instructions on pages 5 8 Fiber Cleansing Formula the SmartMix tank Set the ReadyTools dial to Tools or PreTreat Set SmartMix to Normal and Soil Removal BISSELL Muli Allergen Removal Formula with Scotchgard Protection item 0720 BISSELL Natural Orange Extract Formula with Scotchgard Protection item 0740 Manufacturer s Tag a Deep cleaning carpeting and upholstery regularly Cleaning Technique Choose the 4 Small Area Tool the Tough Stain Brush or the Spraying Crevice Tool and connect to the flex hose o Plug into a proper outlet and turn the Power switch ON While pressing the trigger slowly move the spraying tool back and forth over the soiled surface Release the trigger to vacuum soiled water Continue to clean the soiled area working in small sections until no more dirt can be removed Caution Do not overwet When the cleani
8. ct to a properly grounded outlet See Grounding Instructions W Unplug from outlet when not in use and before conducting maintenance or troubleshooting W Do not leave machine when it is plugged in Wi Do not service machine when it is plugged in L L Do not use with damaged cord or plug f appliance is not working as it should has been dropped damaged left outdoors or dropped into water have it repaired at an authorized service center Use indoors only Do not pull or carry by cord use cord as a handle close door on cord pull cord around sharp corners or edges run appliance over cord or expose cord to heated surfaces Do not carry the appliance while in use Do not unplug by pulling on cord unplug by grasping plug Do not handle plug or appliance with wet hands Do not put any object into appliance openings use with blocked opening or restrict air flow Do not expose hair loose clothing fingers or body parts to openings or moving parts Do not pick up hot or burning objects Do not pick up flammable or combustible materials lighter fluid gasoline kerosene etc or use in the presence of explosive iquids or vapor Do not use appliance in an enclosed space filled with vapors given off by oil base paint paint hinner some moth proofing substances lammable dust or other explosive or toxic vapors Do not pick up toxic material chlorine bleach ammonia drain cleaner gasoline etc Do not modify the 3 prong grounded plug
9. debris deposits on E Rotate SS the carpet that were loosened by the brushing action REND Handle to QU U Especially with newer carpets that have never been deep cleaned before This debris should be picked up by hand and thrown away Debris that deposits in the Brush Belt area should be cleaned out between uses to keep the Belts running free ug310 5921_1697_105 indd 6 2 2105 10 58 35 AM Tank in Tank Continued A WARNING reduce the risk of fire use only BISSELL Fiber Cleansing Formula or BISSELL Hard Floor Solutions in your POWERSTEAMER PRO Use of cleaning formulas which contain lemon or pine oil may damage this appliance and void warranty Chemical spot cleaners or solvent based soil removers should not be used These products may react with the plastic materials used in your POWERSTEAMER PRO causing cracking or pitting Find the mouth of the bladder and fill to the bottom of the neck with hot tap water Do not boil or microwave water NOTE Fill the Bladder with water only Replace the tank lid matching the lid and tank edges Handle must be in forward position to reinstall Rotate the handle to the carrying position to re latch the lid Replace tank machine base seating firmly place Rotate handle back down to the latched position Emptying Tank in Tank Remove the Tank in Tank follow steps 1 and 2 on page 6 Carry the Tank in Tank like bucket to the si
10. etting to match the cleaning job Set the ReadyTools switch on to either Tools PreTreat or Floor Cleaning Pre Treating Optional Improves cleaning effectiveness for heavily soiled carpet in high traffic areas such as entryways and hallways When filling bottle or Q St the SmartMix dial to High Traffic storing unt set dial to 0 2 Set the ReadyTools dial to PreTreat OON o e Plug into a proper outlet and turn ON the Power switch ie pressing the trigger slowly make several passes over the area to be cleaned Caution Do not overwet Turn the machine Power switch OFF and let BISSELL Fiber Cleansing Formula dissolve the tough soil for 1 2 minutes before continuing Normal Cleaning ep Plug into a proper outlet and turn the Power switch ON While pressing the trigger make one slow forward back wet pass Let the Fiber Cleansing Formula and DirtLifter PowerBrush do the work for you Caution Do not overwet Release the trigger and make one slow forward and back pass over the same area to remove any residual dirty water Repeat cleaning passes until solution being pulled appears clean Continue passes without pressing the trigger until you can t see any more water being pulled up NOTE Both the SmartMix and the clean water tanks must have liquid in them in order for the machine to spray If one tank is empty the machine will not apply either cleaning solution or water only
11. in housing Reinstall if necessary Tank in Tank Lid is not properly installed Reinstall lid refer to page 6 Tank in Tank is not properly seated Tank in Tank must be firmly seated to function Remove tank and check gasket on tank bottom Reseat tank Q Poor tool position Readjust angle apply more Handheld attachments only downward pressure Tank in Tank has picked up the maximum Empty tank and refill refer to dirty water page 7 Thank you for selecting a BISSELL product If you should happen to need assistance during assembly or operations call 1 800 237 7691 Please do not return this product to the store 2 2 05 10 58 45 AM BISSELL Consumer Services For information about repairs or replacement parts or questions about your warranty Call BISSELL Consumer Services 1 800 237 7691 Monday Friday 8 a m 10 p m ET Saturday 9 a m 8 p m ET Or write BISSELL HOMECARE INC PO Box 3606 Grand Rapids MI 49501 ATTN Consumer Services Or visit the BISSELL website www bissell com When contacting BISSELL have model number of unit available Please record your Model Number Please record your Purchase Date NOTE Please keep your original sales receipt It provides proof of date of purchase in the event of a warranty claim See About Your Warranty on page 16 for details Replacement Parts Part No Part Name 1 1
12. ine maintenance components such as filters belts or brushes Damage or malfunction caused by negligence abuse neglect unauthorized repair or any other use not in accordance with the User s Guide is not covered If your BISSELL product should require service Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area If you need information about repairs or replacement parts or if you have questions about your warranty contact BISSELL Consumer Services Website or E mail www bissell com Use the Customer Services tab Or Call BISSELL Consumer Services 1 800 237 7691 Monday Friday 8 am 10 pm ET Saturday 9 am 8 pm ET Or write BISSELL Homecare Inc PO Box 3606 Grand Rapids 49501 ATTN Consumer Services BISSELL HOMECARE INC IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT 0 LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION A OF LAW INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND Bissell FITNESS FOR A PARTICULAR PURPOSE ARE LIMIT
13. ion To reduce the risk of until the condition stops fire electric shock or injury unplug DirtLifter PowerBrush from outlet before servicing The powered brush roll at the floor nozzle is designed to enhance cleaning performance The bristle pattern lifts out the deep down dirt while gently grooming carpet fibers The floating suspension self adjusts to all carpet heights and protects your carpet if you leave 2092009102 MAON the power switch ON When the machine handle is in traffic areas on a regular basis the fully upright position CarpetSaver automatically can prolong carpet life raises the brush off the carpet Tank in Tank is designed with bladder inside for clean water As you clean the bladder will empty Dirty water collects in the tank outside the bladder Qe on handle release to lay the machine handle down out of the way Lift the Tank in Tank handle The handle locks the lid place Carry it like a bucket to fill at the sink Handle Release Set the tank down and rotate the handle forward to unlatch the lid Lift off and set the lid aside NOTE Both the SmartMix Tank and the clean water tank must have liquid in them in order for the machine to spray If one tank is empty the machine will not apply either cleaning solution or water only If you re using the WATER ONLY setting fill the SmartMix Tank with water also NOTE You may notice hair and
14. ls are available To order replacement Tank Belt Access parts or tools please refer to page 15 20 Door ex Tough Stain 4 Upholstery Spraying Brush Tool Crevice Tool Ta 7 Hoor Nozzle Window a DirtLifter uu 21 PowerBrush ET 1607 Fiber CAUTI 0 N Cleansing Bare Floor 907 1607 Formula with Solutions PreCleaner protector be stored where there is danger of freezing Freezing will damage internal components cleaning solutions may harm the machine and void the warranty Keep plenty of genuine BISSELL Fiber Cleansing Formula on hand so you can clean whenever it fits your schedule Always use genuine BISSELL deep cleaning formulas Non BISSELL 2 2105 10 58 31 How To Assemble The only thing you will need to assemble your cleaner is a Phillips head 52 screwdriver e Slide Upper Handle onto Lower Handle Feed bundled Power through Tool Caddy from caddy s flat side Align Upper Handle holes and Tool Caddy holes o Place hex nut into back of the Tool Caddy and hold in place Insert bolt from front to back turning into the hex nut until snug Do not over tighten Repeat for second bolt and hex nut Insert 2 screws into lower two holes Turn until snug Snap tools into storage on the Tool Caddy Wrap Power Cord and Flex Hose as shown POWERSTEAMER PRO is a home cleaning system that uses a combination of hot tap water BISSELL adva
15. nced deep cleaning formula and suction to safely clean carpets and upholstery The Power Switch controls power to the machine Provides custom control for each cleaning job Lift the SmartMix concentrate tank out of the machine base the tank over so that the valve cap is an upward position Unscrew the valve cap and fill the tank to the mark with BISSELL Fiber Cleansing Formula Replace the valve cap turning until snug Replace SmartMix concentrate tank NOTE If tank leaks check for proper positioning of o ring ug310 5921_1697_105 indd 5 es 09 The screws are conveniently located in the cellophane package in the accessory box Deep cleaning carpeting and upholstery regularly can reduce dust and allergens in your home SmartMix Tank 2 2105 10 58 34 AM SmartMix Continued the SmartMix setting that fits the cleaning job e Water Only use for gentle cleaning or for the final rinse after cleaning Normal automatically provides the best mix of water and concentrate for most stg cleaning jobs astra oQ WATER 9 ONLY High Traffic automatically mixes the right amounts of water and concentrate to dissolve tough grime and heavy soil NOTE Residual cleaning materials left in carpet from other products may cause excessive foaming when picked up If foam is overflowing tank move SmartMix dial to Water Only posit
16. ng job is complete refer to the Storage section for machine cleanup and storage instructions on page 14 ug310 5921_1697_105 indd 10 can reduce dust and allergens in your home Tip pre treating stairs or entry ways with BISSELL Tough Sain PreCleaner Then deep dean with SmartM dial set to High Traffic 2 2105 10 58 37 AM Cleaning Bare Floors The Bare Floor Tool provides effective cleaning for linoleum vinyl and tile floors Available on select models only Caution Do not use on hardwood floors Use only BISSELL Hard Floor Solutions Vacuum or sweep thoroughly to pick up loose debris and pet hair Remove easily moved furniture from the room chairs tables etc o Plan your cleaning route to leave an exit path Plan activities to allow about 30 minutes for the floor to dry completely Attach the Bare Floor Tool Step on the handle release to lay the machine handle down e Remove the Tank in Tank from the machine base o Lift the machine base to expose the underside of the nozzle Attach Bare Floor Tool to nozzle with long tab to the right side ReadyTools side of the nozzle Qo First attach left side short tab catching tab over nozzle edge Q Gently bend long tab right side outward to easily snap over edge of clear nozzle on right Bottom Front Edge Machine Preparation Bare Floor of Floor Nozzle Set up machine following the instructions on pages 5 8
17. nk where you will dispose of the dirty water e Remove tank lid Pour out dirty water After each use remove and rinse the lint screen located on the tank lid Remove tank assembly from unit Remove tank lid Remove lint screen and rinse under faucet Remove any debris caught in lint screen D Replace lint screen on tank lid Lint screen will click into place Replace tank lid Replace tank assembly into unit Refill with clean tap water as above steps 5 through 9 and refill the SmartMix tank with BISSELL Cleansing Formula as necessary ug310 5921_1697_105 indd 7 Fill Bladder only with clean When filling bottle or storing unit set SmartMix dialtoO lt 2 2 05 10 58 35 AM How To Clean Carpet Emptying Tank in Tank Continued Q Wren the cleaning job is complete rinse out the Tank in Tank by rinsing clean water between the bladder and tank Return the Tank in Tank to the machine following steps 6 through 9 on page 7 Refer to the Storage section on page 12 for the final cleanup The Flow Indicator This is located on the machine base It spins when the trigger is pressed to indicate that the machine is applying cleaning solution to the floor It will stop spinning to indicate that the SmartMix tank or bladder needs to be refilled or when the trigger is released If the flow indicator is not spinning check to make sure the
18. ounding Pin FAN WARNING Improper connection of the equipment grounding conductor can result in a risk of electrical shock Check with a qualified electrician or service person if you aren t sure if the outlet is properly grounded DO NOT MODIFY THE PLUG If it will not fit the outlet have a proper outlet installed by a qualified electrician This appliance is designed for use on a nominal 120 volt circuit and has a grounding attachment plug that looks like the plug in the drawing above Make certain that the appliance is connected to an outlet having the same configuration as the plug No plug adapter should be used with this appliance 2 2105 10 58 30 AM ug310 5921_1697_105 indd 4 ZNWARNING To reduce the risk of fire use only BISSELL Advanced Deep Cleaning Formulas in your PowerSteamer Use of cleaning formulas that contain lemon or pine oil may damage this appliance and void warranty Chemical spot cleaners or solvent based soil removers should not be used These products may react with the plastic materials used in your PowerSteamer causing cracking or pitting Power Cord Quick Release Tough Stain Brush Storage A HA Tank in Tank AX AE WAL AN 4 Upholstery Tool Storage SmartMix TT TM What comes with your Dial itr sie POWERSTEAMER PRO All items may not be included with your model Sm artMix ReadyTools Dial More too
19. the Tank in Tank and SmartMix tanks Set them aside see illustration Qe Belt Access Door located near the Floor Cleaning Tools Switch by inserting a flat head screwdriver into the slot nearest to the handle and gently prying the access door off see illustration Turn the machine onto its side so the belt access area is facing upward see illustration On the bottom of the machine near the belt access area is a red retainer plate that holds the black brush arm and brush in place Using a Phillips head screwdriver remove the screw that holds the red retainer plate in place Set red retainer plate and Phillips head screw aside see illustration Qe the black brush arm that holds the brush in place Set the black brush arm aside see illustration Remove the toothed brush belt from the brush then from the red pump pulley Set the toothed brush belt and brush aside Qe and remove the broken pump belt A WARNING To reduce the risk of fire electric shock or injury unplug appliance from outlet before servicing 2 2105 10 58 44 AM To Install The Replacement Pump Belt Q vin the unit still on its side loop one end of the replacement pump belt around the red pump pulley and then the other end around the silver motor shaft see illustration Do not twist the replacement pump belt e Re install the toothed brush belt first onto the red pump pulley o and then onto the toothed end of the br
20. ug310 5921_1697_105 indd 1 Bissell PowerSteamer Pro series 1697 SERIES GUIDE 3 Exaudi Bissell 4 POWERSteamer 65 55 5 Assembly Instructions 5 11 12 INTE 2 2105 10 58 30 AM gt Thanks For Buying A BISSELL PowerSteamer PRO Deep Cleaner We re glad you purchased BISSELL POWERSTEAMER PRO Deep Cleaner Everything we know about floor care went into the design and construction of this complete high tech home cleaning system Your POWERSTEAMER PRO is well made and we back it with a limited one year warranty We also stand behind it with a knowledgeable dedicated Consumer Services department so should you ever have a problem you ll receive fast considerate assistance My great grandfather invented the floor sweeper in 1876 Today BISSELL is a global leader in the design manufacture and service of high quality homecare products like your POWERSTEAMER PRO 7m A Y LAU Mark J Bissell President and Chief Executive Officer ug310 5921 1697 105 indd 2 2 2 05 10 58 30 AM IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic precautions should be observed including the following Read all instructions before using your POWERSTEAMER PRO A WARNING uc the risk of fire electric shock or injury W Do not immerse Wi Use only on surfaces moistened by cleaning process W Always conne
21. unit is set on Floor Cleaning setting ReadyTools Dial This provides above floor cleaning with the turn of a dial Just choose the cleaning tool attach to the flex hose and PowerSteamer Pro is ready to clean upholstery and more Set the switch to Floor Cleaning when cleaning carpets or bare floors or set it to Tools PreTreat when using the flex hose attachments or for pre treating floors Plan activities to give carpet time to dry Remove easily moved furniture from the room chairs lamps coffee tables etc Vacuum thoroughly to pick loose debris and pet hair before using the PowerSteamer Pro o Plan your cleaning route to leave an exit path It is best to begin cleaning in the corner farthest from your exit ug310 5921 1697 105 indd 8 Thorough vacuuming before deep cleaning will prevent early clogging of the lint trap A special red float device in the tank will cause the cleaner to stop removing solution from the carpet and the motor sound will rise in pitch to let you know the dirty water tank is full Tip Try pre treating stairs or entry ways with BISSELL Tough Stain PreCleaner Then deep clean with SmartMix dial set to High Traffic 2 2105 10 58 36 AM ug310 5921_1697_105 indd 9 Machine Preparation Q up the machine following instructions on pages 5 8 use Fiber Cleansing Formula in the SmartMix tank choose the SmartMix s
22. ush see Illustration Re install the brush into the base of the unit Place the black brush arm onto the brush and slide black brush arm into base of unit The black brush arm and brush should slide easily into original position see illustration Re install the red retainer plate and Phillips head screw see illustration Using your finger gently spin the replacement pump belt on the silver motor shaft If assembled correctly the replacement pump belt should rotate freely around the silver motor shaft and drive pulley without obstruction The brush should also rotate freely when the silver motor shaft is turned e Turn the machine right side up and replace the Tank in Tank Smart Mix tank and belt access door see illustration Assembly is now complete If you have any questions or are having trouble installing your replacement pump belt please call BISSELL Consumer Services at 1 800 237 7691 Troubleshooting Reduced Spray Or No Spray Possible Causes Bladder may be empty SmartMix tank may be empty The Flow Indicator Filter may be clogged Tank in Tank may not be seated properly Pump may have lost prime ug310 5921 1697 105 indd 13 AN WARNING To reduce the risk of fire electric shock or injury unplug appliance from outlet before servicing Remedies Tum power OFF refill tank with hot tap water Turn power OFF clean out lint screen
23. witch OFF stored with concentrate QQyunblua power cord from the outlet and coil around Power Cord ready for your next cleaning Quick Release job Make sure dial is set to remove and rinse tools in clean running water let dry and Water Only replace in tool caddy hose around storage brackets tool caddy Qv Tank in Tank dispose of dirty water out the Tank in Tank and replace on the machine Clean out the Flow Indicator Filter each time it is used to insure best cleaning performance Unscrew the Flow Indicator Cap lift out the red Rotor and white Filter Rinse all three parts in tap water Replace the Filter and Rotor Replace the Flow Indicator Cap turn until snug do not over tighten NN Cap Note SmartMix tank may be stored with concentrate ready for jo Rotor your next cleaning job Make sure dial is set to Water Only Fiter Qe all exterior surfaces with a soft cloth Qv cleaner upright in a protected dry AN CAUTI 0 N Quen carpet is dry vac in t hair and fuzz that IS dry vacuum again to remove and Tuzz tha uses water and the POWERSTEAMER may have loosened must not be stored where there is a Pump Belt and Brush Belt Replacement danger of freezing Freezing will Qu the machine off and unplug from wall outlet damage internal components and void the warranty the release pedal and recline the handle down onto floor see illustration
Download Pdf Manuals
Related Search