Bionaire 127176 Electric Heater User Manual
Contents
1. long an implied warranty lasts so the above limitations or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from province to province state to state or jurisdiction to jurisdiction How to Obtain Warranty Service In the U S A If you have any question regarding this warranty or would like to obtain warranty service please call 1 800 253 2764 and a convenient service center address will be provided to you In Canada If you have any question regarding this warranty or would like to obtain warranty service please call 1 800 253 2764 and a convenient service center address will be provided to you In the U S A this warranty is offered by Sunbeam Products Inc doing business as Jarden Consumer Solutions located in Boca Raton Florida 33431 In Canada this warranty is offered by Sunbeam Corporation Canada Limited doing business as Jarden Consumer Solutions located at 20B Hereford Street Brampton Ontario L6Y OM1 If you have any other problem or claim in connection with this product please write our Consumer Service Department PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE gt d ONINI FIREPLACE heater BFH5000 Read instructions before operating SEN ir itiuirehetchomee Instruction Leaflet INFO LINE If after having read this leaflet you have any questions or comments on your heater call2. Consumer Services Department at 1 800 253 2764 Flame not bright enough 1 Regulate flame brightness using the Flame Brightness button 2 Check both bulbs are working and replace if necessary Simulated fire will not illuminate 1 Check power 2 Press Flame Button amp 3 Check both bulbs and replace if necessary Unit making crackling popping sound 1 Unit is intended to replicate the gentle popping and crackling sounds of a residential fireplace 2 Press Sound md button to adjust 4 levels of sound and to turn off sound Heat will not turn off 1 Refer to operating instructions 2 Press Thermostat button until 00 is displayed The fan will continue to run for flame operation Heater blows cool air 1 This is normal in order to cool down the heater and preserve the heating element 2 This is normal when the heat is turned off Remote does not work 1 Change batteries see Assembly Instructions 2 Be sure to point Remote at Control Panel on unit 3 Be sure there are no obstructions between remote and unit 4 Make sure glass over LCD Display is clean 5 Ideal range for Remote Control is within 20 feet Not enough heat 1 Increase thermostat setting to highest setting 2 This is a 1500 watt heater and is intended for supplement heat only Heater cycles on and off frequently 1 The thermostat automatically turns the heater on and off to maintain selected comfort level 2 lo make this occur less frequently adj
3. alter modify or any way change the terms and conditions of this warranty This warranty does not cover normal wear of parts or damage resulting from any of the following negligent use or misuse of the product use on improper voltage or current use contrary to the operating instructions disassembly repair or alteration by anyone other than JCS or an authorized JCS service center Further the warranty does not cover Acts of God such as fire flood hurricanes and tornadoes What are the limits on JCS s Liability JCS shall not be liable for any incidental or consequential damages caused by the breach of any express implied or statutory warranty or condition Except to the extent prohibited by applicable law any implied warranty or condition of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty JCS disclaims all other warranties conditions or representations express implied statutory or otherwise JCS shall not be liable for any damages of any kind resulting from the purchase use or misuse of or inability to use the product including incidental special consequential or similar damages or loss of profits or for any breach of contract fundamental or otherwise or for any claim brought against purchaser by any other party Some provinces states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how
4. exhaust opening as this may cause an electric shock or fire or damage the heater 10 DO NOT operate heater with a damaged cord or plug or after the heater malfunctions or has been damaged in any manner Return appliance to manufacturer for examination electrical or mechanical adjustment or repair 11 A heater has hot and arcing or sparking parts inside DO NOT use it in areas where gasoline paint or flammable liquids are used or stored 12 Use appliance only for intended household use as described in this manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to persons The use of attachments not recommended or sold by the manufacturer may cause hazards 13 DO NOT use outdoors 14 To prevent a possible fire DO NOT block air intakes or exhaust in any manner DO NOT use on soft surfaces like a bed where openings may become blocked 15 To disconnect heater press the On Off button then remove plug from outlet 16 Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire However if you have to use an extension cord the cord should be No 14AWG minimum size and rated not less than 1875 watts 17 If the heater will not operate see specific instructions under Auto Safety Shut off on resetting the heater 18 DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit Doing so will void your warranty
5. 1 800 253 2764 in North America PANG AVAAS HEATER SAFETY PLEASE READ AND SAVE THESE IMPORTANT SAFEGUARDS IMPORTANT INSTRUCTIONS When using electrical appliances basic safety precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following 1 Read all instructions before using the appliance 2 To avoid fire or shock hazard plug the appliance directly into a 120V AC electrical outlet 3 The heater is hot when in use To avoid burns DO NOT let bare skin touch hot surfaces Use handle when moving this heater Keep combustible materials such as furniture pillows bedding papers clothes and curtains at least 3 ft 0 9 m from the front of the heater and keep them away from the sides and rear 4 DO NOT run cord under carpeting DO NOT cover cord with throw rugs runners or the like Arrange cord away from traffic area and where it will not be tripped over 5 This heater is not intended for use in bathrooms laundry areas and similar indoor locations NEVER locate heater where it may fall into a bathtub or other water container 6 Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended 7 Always unplug the heater when not in use When unplugging be sure to pull by the plug and not the cord 9 DO NOT insert or allow foreign objects to enter any ventilation or
6. CLEANING MAINTENANCE Always unplug the heater before cleaning and allow to cool e To clean glass use household glass cleaner e Lightly run a vacuum cleaner nozzle over the heater grill to remove any dust or dirt that may have accumulated e Carefully wipe the heater with a soft damp cloth Please be very cautious near the heating elements e NEVER use abrasive or flammable solvents to clean the heater e After cleaning be sure to completely dry the heater with a cloth or towel e Store your heater in a cool dry location AUTO SAFETY SHUT OFF This heater is equipped with a technologically advanced safety system that automatically shuts off the current to the heater when a potential overheat temperature is reached The heater can only resume operation when you reset it To Reset the Heater If your heater shuts down follow these steps 1 Unplug the heater and wait 30 minutes 2 Plug in the heater turn the power ON 3 Your heater should now be operating properly TIP OVER SHUT OFF If the heater is Knocked over it will instantly shut off To resume operation simply place the heater in an upright position and press the Power button BULB REPLACEMENT Two 25W Candelabra Base Bulbs can be replaced by opening doors on back of unit with a flathead screwdriver TROUBLESHOOTING e Please DO NOT attempt to open or repair the heater other than bulb replacement Please see the Warranty for Service Instructions or call our
7. The inside of the unit contains no user serviceable parts All servicing should be performed by qualified personnel only 19 DISCONTINUE USE IF PLUG OR OUTLET IS HOT RECOMMEND OUTLET BE REPLACED IF PLUG OR OUTLET IS HOT TO TOUCH PLEASE SAVE THESE INSTRUCTIONS CONSUMER SAFETY INFORMATION THIS APPLIANCE HAS A POLARIZED PLUG one blade is wider than the other To reduce the risk of electric shock this plug is intended to fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS TECHNICAL SPECIFICATIONS Amps 129 Wattage 1500W 5 10 Working Voltage 120V AC 60 HZ Bulb Type 2 25W max Candelabra Base Avoid overloading your circuit by not using other high wattage appliances in the same outlet At 1500 Watts this unit draws 12 5 Amps ASSEMBLY INSTRUCTIONS Please make sure to check packaging for parts that could be used to operate your heater This package includes 1 Fireplace Heater 1 Remote Control 2 AAA Batteries for Remote 1 Stand 4 Machine Screws for stand 1 Wall Mount Hardware Kit 2 Light bulbs Installing Batteries into the Remote Before operation insert 2 AAA batteries into the back of the remote contro
8. ettings are Temperature 80 Timer OFF Flame Brightness HIGH Sound ON 3 Thermostat e Press Thermostat button until desired temperature level appears on LCD Display It is recommended to start by setting the temperature to the highest setting When your room reaches the desired comfort level lower the thermostat until the heat stops and thermostat light turns off Note the fan will continue to run for flame operation e The system now maintains the selected comfort level by automatically turning the heater ON and OFF The Thermostat light cycles ON and OFF with the heater element as it maintains the programmed temperature e When LCD reads 00 the heat will turn off but the fan will continue to run for flame operation G Timer You can set the timer to automatically turn the unit off Press the Timer button select between 1 and 12 hours Your selection will then be displayed on the LCD Flame Brightness There are four flame brightness settings HIGH MEDIUM LOW OFF Press button to select desired brightness wt Sound Press Sound button to adjust 4 sound levels or turn crackling sound on or off F C Fahrenheit Celsius Press to show temperature in Fahrenheit or Celsius To mount into drywall Use toggle bolts for 3 8 5 8 10 16 mm thick drywall 1 Cut Mounting Template on dotted line and tape onto wall Use level to make sure template is level and mark wall with a sharp object such as an awl 2 Dril
9. ing the Wall Mounting Template provided see below 3 Hang main body on wall brackets by lifting over the bracket and sliding down 4 Use Cord Wrap to hide extra cord To mount into wall studs 1 Find studs in wall Studs are typically 16 40 cm apart 2 Cut Mounting Template on dotted line and tape onto wall so brackets are centered on studs 3 Use level to make sure template is level Using a sharp object such as an awl mark hole location 4 Using a Power Driver with Phillios head bit drive 1 5 88 mm screws through bracket and drywall into wood or metal stud IMPORTANT Before drilling into any wall ensure no electrical cables are present in the area OPERATING INSTRUCTIONS e There may be an odor coming from the heater the first time you use it This is normal during the break in period Make sure the heater is in a well ventilated area and continue running it until the smell goes away e You may hear a popping or crackling sound as the heater heats up This is normal and safe operation e The Fireplace Heater can be operated by using the remote control Fig 1 or the control panel Fig 2 located on the top of the unit e Place the heater on a firm level surface or mount on wall e Avoid overloading your circuit by not using other high wattage appliances in the same outlet At 1500 Watts this unit draws 12 5 Amps D Power On Off Turn Power ON LCD and Power Light will illuminate The units default s
10. l e Do not mix old and new batteries e Do not mix alkaline standard carbon zinc or rechargeable nickel cadmium batteries The remote control for this unit has the capability of operating all control panel functions Please note this remote will not work through walls Bulb Placement Unwrap the two 25W Candelabra Bulbs from cardboard insert found at the top of unit and open doors on back of unit with a screwdriver Mark for Drill h BRACKET GUIDE 4 toggle bolts 2 mounting brackets Mark for Drill Ca Included for mounting 4 1 5 38 mm Phillips head self tapping screws Stand Assembly For floor use attach the Stand to the Fireplace heater using the 4 machine screws provided Gently lay the unit on the floor and attach the Stand to the bottom For wall mount see Wall Mount Instructions below Wall Mount Installation This product weighs 25 lbs Do not install alone Mounting Template with instructions is attached below to make mounting your Fireplace Heater easy e Wall Mount Hardware Kit includes 4 1 5 Phillips head self tapping screws 4 toggle bolts 2 mounting brackets IMPORTANT Before drilling into any wall ensure no electrical cables are present in the area Max height of 47 1 2 m Make sure you allow at least 3 feet 1m of space on the sides of unit 1 Remove stand from main unit if installed 2 Secure the mounting brackets to the wall us
11. l 3 8 10 mm holes at top and bottom of bracket guide in center of studs 3 A Align bolts through bracket holes then thread on Spring Loaded Wings B Collapse Wings while pushing through hole in wall Spring C Pull bolt out to secure Toggle Wings against inside of wall wings spring Loaded open on other side of wall and securely hold bolt and bracket aon D Screw bolt in until tight neideof wall Note The mounting hardware included is intended for mounting the heater on 3 8 to 5 8 10 16mm drywall affixed to wood or metal studs For your convenience the wall mount brackets are 16 40 cm on center to align with 2 studs Not all studs will be 16 40 cm on center If you are not able to align with studs toggle bolts are provided For other wall types please consult a professional or visit your local hardware store to determine which type of hardware is best for your particular wall KEY TO ICONS O On Off Thermostat 4 Timer 4y Flame Brightness d Sound Ute F C Fahrenheit Celsius REMOTE CONTROL CONTROL PANEL Back of Heater Front of Heater FRONT BACK Control Panel Buttons LCD Display Heat Vent Handle Hanging Brackets Light Bulbs BRACKET GUIDE Power Light Removable Stand Mark for Drill Mark for Drill Cord Wrap
12. ust the thermostat setting up or down HEATER SERVICE INSTRUCTIONS PLEASE DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE If you have any questions regarding your Bionaire product please call us at 1 800 253 2764 or visit us on the web at www bionaire com PLEASE CHECK PACKAGING FOR PARTS BEFORE DISCARDING 1 YEAR LIMITED WARRANTY Sunbeam Products Inc doing business as Jarden Consumer Solutions or if in Canada Sunbeam Corporation Canada Limited doing business as Jarden Consumer Solutions collectively UCS warrants that for a period of one year from the date of purchase this product will be free from defects in material and workmanship JCS at its option will repair or replace this product or any component of the product found to be defective during the warranty period Replacement will be made with anew or remanufactured product or component If the product is no longer available replacement may be made with a similar product of equal or greater value This is your exclusive warranty Do NOT attempt to repair or adjust any electrical or mechanical functions on this product Doing so will void this warranty This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable Keep the original sales receipt Proof of purchase is required to obtain warranty performance JCS dealers service centers or retail stores selling JCS products do not have the right to
Download Pdf Manuals
Related Search