Beko BK 2600 and BK 3500 Air Conditioner User Manual
Contents
1. Whether the wireless remote control is damaged If water leakage in the room The air humidity is on the high side Condensing water over flowed The connection position of indoor unit drainage pipe is loosed If water leakage in outdoor unit When the unit is running in COOL mode the pipe and connection of pipe would be condensed due to the water cooled down When the unit is running in Auto Defrosting mode the ice thawed and flowed out When the unit is running in HEAT mode the water adhered on heat exchanger dripped off Noise from indoor unit emitted The sound of fan or compressor relay is switching on or off When the defrosting is started or stop running it will sound That is due to the refrigerant flowed to the reverse direction 15 Troubleshooting Phenomenon Troubleshooting Indoor unit cannot deliver air In HEAT mode when the temperature of indoor heat exchanger is very low that will stop deliver air in order to prevent cool air Within 2min In HEAT mode when the outdoor temperature is low or high humidity there are much frost be formed on the outdoor heat exchanger that the unit will automatically defrost indoor unit stop blowing air for 3 12min During the defrosting there is water flowing out or vapor be produced In dehumidifying mode sometimes indoor fan will stop in order to avoid condensing water be vapo rized again restrain temperature rising2. bodies a Clear dust and obstructions from the outdoor unit Repaint the rubiginous place on the outdoor unit to prevent it from spreading 5 Adopt the special shield to cover the outdoor unit avoid the rain water dust enter into the unit and get rust 13 Troubleshooting A CAUTION Don t attempt to repair the air conditioner by yourself it can cause an electric shock or fire Please check the following items before asking for repair it can save your time and money Phenomenon Troubleshooting Not operate immediately when the air conditioner is restarted EX Waiting 3 RO e Once the air conditioner is stopped it will not operate in approximately 3minutes to protect itself There s unusual smell blowing from the outlet after operation is started FA IN AA The unit has no peculiar smell by itself If has that is due to the smell accumulated in the ambient e Solution method Cleaning the filter If problem still has so need to clean air conditioner Please contact with the authorized maintenance center Sound of water flow can be heard during the operation e The air conditioner is started when it is running the compressor started or stopped running or the unit is stopped sometimes there is swoosh or gurgle the sound is due to refrigerant flowing they are not malfuncti ons In COOL mode sometimes the mist emitted from the air outl
3. Moisture on air outlet vent If unit is running under the high humidity for a long time the moisture will be condensed on the air outlet grill and drip off Immediately stop all operations and plug out contact the dealer in following situations There is harsh sound during operation The terrible odors emitted during operation Water is leaking in the room Air switch or protection switch often breaks and power plug Carelessy splash water or something into unit There is an abnormal heat in power supply cord S gt Stop running and pull out of the plug 2 16 Notices for installation C TO Important Notices 1 The unit installation work must be done by qualified personnel according to the local rules and this manual 2 Before installating please contact with local authorized maintenance center if unit is not installed by the authorized maintenance center the malfunction may not solved due to discommodious contacts 3 When removing the unit to the other place please firstly contact with the authorized Maintenance Center in the local area C Basic Requirements For Installation Position D Install in the following place may cause malfunction If it is unavoidable contact with service center please e Place where strong heat sources vapors flammable gas or volatile object are emitted O Place where high frequency waves are generated by radio equipment wel
4. adjacent structures va Space to the obstruction Ocm Above 5 lt SS Sp 4 o A Air outlet side 19 Air inlet side Space to the wall 00m Above gt 4 Install indoor unit C Install the rear panel 1 Always mount the rear panel horizontally Due to the water tray of indoor unit has been adopted the both way drainage design the outlet of water tray should be adjusted slightly down when installing that is taking the outlet of the water tray as the center of a circle the included angle between the evaporator and level should be 0 or more that is good for condensing water drainage 2 Fix the rear panel on the wall with screws Wall _ Wall Mark on the middle of it Br Gradienter Space SS Where is pre covered with plastic granula Space ito the EZ Ta to the 3 Be sure that the rear panel has been fixed wall p lt 2 wall A 50m a 50m firmly enough to withstand the weight of an NE i i adult of 60kg further more the weight should be evenly shared by each screw j Right 55mm Rear piping hole Rear piping hole Install the piping hole Indoor Outdoor 1 Make the piping hole 55 in the wall at a slight downward slant to the Wall pipe outdoor side Seal pad 2 Insert the piping hole sleeve into the hole to prevent the connection piping and wiring from being damaged when passing through the hole 55 Install the water draina
5. and will cause fire or electric shock C Install the indoor unit External connection e The piping can be lead out from right right rear left a a left rear A 1 When routing the piping and wiring from the left Tailing 2 or right side of indoor unit cut off the tailings Ci Falling 1 Ges geo DITTA from the chassis in necessary Show in Fig 7 Fig 7 Finally wrap it Nt e 1 Cut off the tailings 1 when routing the wiring only 2 Cut off the tailings 1 and tailings 2 when routing both the wiring and piping 2 Take out the piping from body case wrap the piping electric wire water pipe with tape and pull them through the piping hole As show in Fig 8 3 Hange the mounting slots of the indoor unit on the upper tabs of the rear panel and check if it is firm enough As show in Fig 9 Ky Mounting 4 The height of the installed location should be 2 5m ae j or more from the floor Y Fig 9 le Install the connection pipe 1 Align the center of the piping flare with the relevant valve 2 Screw in the flare nut by hand and then tighten the nut with spanner and torque wrench refer to the following Me e Indoor unit piping Taper nut Piping amp A Hex nut diameter Tightening torque N m Esa RS 3135 o 2 5055 Spanner 7 4 Torque 60 65 wrench 0 19 70 75 NOTE Firstly connect the connection pipe to indoor unit then to outdoor unit pay attention to the piping bending do not da
6. indoor unit may blow gentle breeze and the guide louver rotate to a certain position 1 In Heat mode the unit turned on the compressor doesn t arrive the starting condition 2 In Heat mode the temperature arrive at the setting value and the compressor stop running about 1min X Working temperature range Indoor sideDB WB C Outdoor sideDB WB C Maximum cooling 35 24 43 Minimum cooling 21 15 21 Maximum heating 24 21 15 5 Minimum heating 20 7 The operating temperature range outdoor temperature for cooling unit is 18 C 43 C for cooling and heating unit is 7 C 43 C 6 Names and functions of each part Indoor unit d The pattern in displayer o E Cool La Dry Wireless Fan remote control Heat amp HH 2 Remote control Run o 1 Power cable Set temp 3 Front panel 4 Filter 5 Guide louver 6 Wall pipe 7 Bind tape Outdoor unit 8 Connection wire 9 Drainage pipe 4 Operation of wireless remote control Names and functions of wireless remote control Note Be sure that there are no obstructions between receiver and remote controller Don t drop or throw the remote control Don t let any liquid in the remote control and put the remote control directly under the sunlight or any place where is very hot Signal
7. BK 2600 BK 3500 Split Air Conditioner User Manual BEKO CONTENTS Operation and maintenance K Notices for operation Notices for use Emergency operation Clean and care Troubleshooting Installation service Notices for installation Installation dimension diagram 19 Install indoor unit 20 Install outdoor unit 22 Check after installation and test operation 23 Installation and Maintenance of Healthy Filter 24 This symbol stands for the items This symbol stands for the items should be forbidden should be followed The products in this manual may be different with the real one according to different N models some models have displayer and some models without displayer the position and shape of the displayer please refer to the real one This appliance is not intended for use by persons including children with reduced physiced sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person reponsible for thei r safety Children should be supervised to ensure that they do not play with the appliance Do not dispose this product as unsorted municipal waste Collection of such waste separately for special treatment is necessary Operation and maintenance notices for operation A K Earth The ground be connected If not please ask the qualified person nel
8. agrams on the front panel C Clean the air filter Recommended once every three months NOTE If dust is much more around the air conditioner the air filters should be cleaned many times After taking off the filter don t touch the fin of indoor unit in order to avoid hurt your fingers Take down the air filter l M At the slot of surface panel to open an angle pull the air filter downward and take it out please see the Fig 4 a b a 2 Clean the air filter To clean the dust adhering to the filters you can either use a vacuum cleaner or wash them with warm water the water with the neutral detergent should below 45 degree and dry it in the shade NOTE Never use water above 45 C to clean or it can cause deformation or discoloration Never parch it by fire or can cause a fire or deformation 3 Insert the air filter Reinsert the filters along the direction of arrowhead and then to cover the cover and clasp it 12 Clean and care C Check before use Be sure that nothing obstructs the air outlet and intake vents 2 Check that whether ground wire is properly connected or not 3 Check that whether the batteries of air conditioner are changed or not 4 Check that whether the installation stand of the outdoor unit is damaged or not If damaged please contact the dealer C Maintain after use Turn main power off Clean the filter and indoor and outdoor units
9. al that will return to display the setting temperature if the users haven t set up the temperature displaying status that will display the setting temperature This function is applicable to partial of models button Presetting temperature can be decreased Press this button the temperature can be set up continuously press this button and hold for two seconds the relative contents can quickly change until unhold this button and send the order that the R F signal will be displayed all the time The temperature adjustment is unav ailable under the Auto mode but the order can be sent by if pressing this button Operation of wireless remote control Names and functions of wireless remote control Notice This is a general use remote controller it could be used for the air conditioners with multifunction For some function which the model dosen t have if press the corresponding button on the remote controller that the unit will keep the original running status TIMER ON TIMER ON BUTTON Time r On setting Signa ON will blink and display signa will conceal the numerica sectio n will becom e the timer on settin g status Durin g 5 second s blink by pressin g or button to adjus t the time valu e of numerica section ever y pres s of that button the valu e will be increase d or decrease d 1 minute Hold pressin g or button 2 second s later it quick
10. all pole disconnection switch having a contact separation of at least 3mm in all poles should be connected in fixed wiring Note O Make sure that the Live wire or Zero line as well as the earth wire in the family power socket can not be wrong connected there should be reliable and no short circuit in the diagram O wrong connection may cause fire 4 Earthing requirements Air conditioner is type I electric appliance thus please do conduct reliable earthing measure The yellow green two color wire in air conditioner is earthing wire and cannot be used for other propose It cannot be cut off and be fix it by screw otherwise it would cause electric shock The earth resistance should accord to the National Criterion The user power must offer the reliable earthing terminal Please don t connect the earthing wire with the following place 0 Tap water pipe 2 Gas pipe 3 Contamination pipe 4 Other places that professional personnel consider them unreliable The model and rating values for fuses according the silk print on fuse cover or related PCB board 18 Installation dimension diagram E Aa AA a Space to the ceiling lt l5cm yd Above SemAbov gt e to the wall Space to the floor e The dimensions of the space necessary for correct installation of the appliance including the minimum permissible distances to
11. d then close the panel cover C Cleaning and Maintenance Take out the healthy filter before cleaning and reinstall it after cleaning according to the installation instruction Pay special attention to that silver ion filter can t be cleaned with water while active carbon photocatalyst low temperature conversion LTC catalyst formaldehyde eliminator ca techin or mite killing filter can but can t with brush or hard things Dry it in the shade or sun after cleaning but not by wiping le Service Life gt The healthy filter commonly has its usage lifetime for one year under normal condition As for silver on filter it is invalid when its surface becomes black green e This supplementary instruction is provided for reference to the unit with healthy filter If the graphics provided herein is different from the physical goods the latter one shall prevail The quantity of healthy filters shall be based on the actual delivery 24 www beko com Il II MN 66129914640
12. ders and medical equipment O Place where a lot of salinities such as coast exists O Place where the oil machine oil is contained in the air Place where a sulfured gas such as the hot spring zones is generated O Other place with special circumstance C Indoor Unit Installation Position Selection 1 The air inlet and outlet vent should be far from the obstruction make sure that the air can be blown through the whole room 2 Select a position where the condensing water can be easily drained out and the place is easily connected for outdoor unit 3 Select a location where the children can not reach 4 Can select the place where is strong enough to withstand the full weight and vibration of the unit And will not increase the noise 5 Be sure to leave enough space to allow access for routine maintenance The height of the installed location should be 250cm or more from the floor 6 Select a place about 1m or more away from TVset or any other electric appliances 7 Select a place where the filter can be easily taken out 8 Make sure that the indoor unit installation should accord with installation dimension diagram requirements 9 Do not use the unit in the immediate surroundings of a laundry a bath a shower or a swimming pool Outdoor Unit Installation Position Selection D Select a location from which noise and outflow air emitted by unit will not inconvenience neighbors animals plants 2 Select a loca
13. direction can be adjusted appro priately At operating adjust the vertical airflow direction by adjusting the louvers of upward do wnward direction And then hold two ends of left and right louver to adjust the horizontal air flow Louver of upward downward direction Louver of left right direction Don t insert your hands or stick into the air intake or outlet vents Otherwise it will cause accident X Don t blow the wind to animals and plants directly It can cause a bad influence to them X Don t apply the cold wind to the body for a long time Splashing water on the air conditioner can cause an electric shock and malfunction Don t use the air conditioner for other purposes such as drying clothes preserving foods etc Don t place a space heater near the air conditioner Or CO toxicosis may occur for imcomplete burning Notices for use Working principle and special functions for cooling Principle Air conditioner absorbs heat in the room and transmit to outdoor and discharged so that indoor ambient temperature decreased its cooling capacity will increase or decrease by outdoor ambient temperature Anti freezing function If the unit is running in COOL mode and in low termperature there will be frost formed on the heat exchanger when indoor heat exchanger temperature decreased below 0 C the indoor unit microcomputer will stop compressor running and protect the unit Work
14. e When it is powered off the guide louver of main unit will close automatically 2 Press MODE button select desired running mode 3 Pressing or button to set the desired temperature It is unnecessary to set the temp at AUTO mode 4 Pressing FAN button set fan speed can select AUTO FAN LOW MID and HIGH 5 Pressing 3l button to select the swing Guide for operation Optional operation 1 Press SLEEP button to set sleep 2 Press TIMER ON and TIMER OFF button can set the scheduled timer on or timer off 3 Press LIGHT button to control the on and off of the displaying part of the unit This function may be not available for some units 4 Press TURBO button can realize the ON and OFF of TURBO function Introduction for special function X About X FAN function This function indicates that moisture on evaporator of indoor unit will be blowed after the unit is stopped to avoid mould 1 Having set X FAN function on After turning off the unit by pressing ON OFF button indoor fan will continue running for about 10 min at low speed In this period press X FAN to stop indoor fan directly 2 Having set X FAN function off After turning off the unit by pressing ON OFF button the button complete unit will be off directly X About AUTO RUN When AUTO RUN mode is selected the setting temperature will not be displayed on the LCD the unit will be in accordance with the room temp automatically to select the s
15. e power cord specified It may cause electric malfunction or damage the part Is the inlet and outlet been covered It may cause insufficient cooling heating capacity Has the length of connection pipes and refrigerant capacity been recorded he The refrigerant capacity is not accurate C Test Operation 1 Before test operation 1 Do not switch on power before installation isfinished completely 2 Electric wiring must be connected correctly and securely 3 Cut off valves of the connection pipes should be opened 4 All the impurities such as scraps and thrums must be cleared from the unit 2 Test operation method 1 Switch on power press ON OFF button on the wireless remote control to start the operation 2 Press MODE button to select the COOL HEAT Cooling only unit is not available FAN to check whether the operation is normal or not 23 4 Installation and Maintenance of Healthy Filter C Installation Instructions 1 Forcibly pull the panel for a specific angle from the two ends of the front panel according to the arrow direction Then pull the air filter downwards to remove it See Fig a 2 Mount the healthy filter onto the air filter as shown in Fig b If the air filter cannot be in stalled please mount the healthy filter on the front case as shown in Fig c 3 Mount the air filter properly along the arrow direction in Fig d an
16. ess this button can set up the temperature when unit is on Continuously press and hold this button for more than 2 seconds the corresponding contents will be changed rapidly until unpress the button then send the information E isp laying all along In Auto mode the temp erature can not be set up but operate this button can send the signal Centigrade setting range 16 30 Fahrenheit scale Remote control setting range 61 86 TURBO button In Cool or Heat mode press this button can turn on or turn off the Turbo function After turned on the Turbo function its signal will be displayed When switching the mode or changing fan speed this function will be canceled automatically X FAN button PressingX FAN button in COOL or DRY mode the icon CRalisplayed and the indoor fan will continue operation for 10 minute in order to dry the indoor unit TEMP button Press this button could select displaying the indoor setting temperature or indoor ambient temperature When the indoor unit even though you have turned off the unit firstly power on it will display the setting After energization X FAN OFF is defaulted temperature if the temperature s displaying X FAN is not available in AUTO FAN or status is changed from other status to HEAT mode displays the ambient temperature 5s later Note X FAN or BLOW same function or within 5s it receives other remote control different name sign
17. et vent When the indoor temperature and humidity are very high this phenomenon would happen This is caused by the room air is swiftly cooled down After running for a while indoor temperature and humidity will fall down the mist will die away Creaking noise can be heard when start or stop the unit So 0 0 o hh e This is caused by the deformation of plastic due to the changes of temperature 14 4 Troubleshooting Phenomenon Troubleshooting The unit can not run gt SS Breaking o Has the power been shut down Is power plug loosed Is the circuit protection device tripped off or not Is voltage higher or lower Tested by professionals Is the TIMER correctly used Cooling Heating efficiency is not good O ad gt Y 0 0 _ os Is Temp setting suitable Were inlet and outlet vents obstructed Is filter dirty Are the windows and doors clothed Did Fan speed set at low speed Is there any heat sources in the room Wireless remote control is not available Fa TS S r The unit is interfered by abnormal or frequent functions switchover occasionally the controller cannot operate At this time you need to pull out of the plug and reinsert it Is it in its receiving range Or obstructed To check the voltage in wireless remote control inside is charged otherwise to replace the batteries
18. fan but when operating this button the wireless adjustable low fan speed is imperative CLOCK button Press this button the clock can be set up signal link and display Within 5 seconds the value can be adjusted by pressing or button if continuously press this button for 2 seconds above in every 0 5 seconds the value on ten place of Minute will be increased 1 During blinking repress the Clock button signal will be constantly displayed and it denotes the setting succeeded After powered on 12 00 is defaulted to display and signal will be displayed Ifthere is signal e displayed that denotes the current time value is Clock value otherwise is Timer value LIGHT button Press this button to select LIGHT on or off in the displayer When the LIGHT o nis set the icon Will be displayed and the indicator light in the displayer will be on When the LIGHT offis set the icon vi not be display ed and the indicator light in the displayer will be off Operation of wireless remote control Names and functions of wireless remote control Notice This is a general use remote controller it could be used for the air conditioners with multifunction For some function which the model dosen t have if press the corresponding button on the remote controller that the unit will keep the original running status button For presetting temperature increasing Pr
19. ge pipe 1 For well draining the drain hose should be placed at a downward slant renched 2 Do not wrench or bend the drain hose or flood its end by water 3 When the long drainage hose passing through indoor should wrap the insulation materials gt lt Flooded C Connect indoor and outdoor electric wires 1 Open the surface panel 2 Remove the wiring cover Fig 6 3 Route the power connection cord from the back of the indoor unit and pull it toward the front through the wiring hole for connection 4 Reassemble the clampand wiring cover 5 Recover the surface panel Wiring Cover N 2 3 black brown yellow green outdoor unit connection 20 4 Install indoor unit NOTE When connecting the electric wire if the wire length is not enough please contact with the authorized service shop to buy a exclusive electric wire that is long enough and the joint on the wire are not allowed e The electric wiring must be correctly connected wrong connection may cause spare parts malfunction e Tighten the terminal screw in order to prevent loose e After tighten the screw slight pull the wire and confirm whether is it firm or not e If the earth wire is wrong connection that may cause electric shock The cover plate must be fixed and tighten the connection wire if it is poor installed that the dust moisture may enter in or the connection terminal will be affected by outside force
20. ght will be off if the AC receives this signal C Emergency operation If the wireless remote control is lost or broken please use the manual switch button At this time the unit will run at the Auto mode but the temperature and fan speed cannot be changed The operation was shown as below Manual switch To open the panel the manual switch Fig 3 is on the displayer box Turn on the unit At unit turned off press the button the unit will run at Auto mode immediately The microcomputer will accord to the indoor temperature to select Cooling Heating Fan and obtain the comfortable effect e Turn off the unit At unit turned on press the button the unit will stop working 11 4 Clean and care A Casio Turn power off and pull out the power plug before cleaning air conditioner or it may cause electric shock Never sprinkle water on the indoor unit and the outdoor unit for cleaning because it can cause an electric shock Volatile liquid e g thinner or gasoline will damage the air conditioner So wipe the units with a dry soft cloth or a cloth slightly moistened with water or cleanser C Clean the front panel D When cleaning the front panel please dip the cloth into the water temperature of 45 C below then to dry the cloth and wipe the dirty part Note Please do not to immerse the front panel in water due to there are microcomputer components and circuit di
21. ing principle and special functions for heating Principle Air conditioner absorbs heat from outdoor and transmits to indoor in this way to increase room temperature This is the heat pump heating principle its heating capacity will be reduced due to outdoor temperature decrease If outdoor temperature becomes very low please operate with other heating equipments Defrosting x When outdoor temperature is low but high humidity after a long while running frost will form on outdoor unit that will effect the heating effect at this time the auto defrosting function will act the heat running will stop for 8 10mins x During the auto defrosting the fan motors of indoor unit and outdoor unit will stop During the defrosting the indoor indicator flashes the outdoor unit may emit vapor This is due to the defrosting it isn t malfunction After defrosting finished the heating will recover automatically The climate type of this unit is according to the nameplate The external static pressures at which the appliance was tested should be zero Pa Notices for use Anti cool wind function In Heat mode under the following three kinds of state if indoor heat exchanger doesn t arrive at certain temp indoor fan will not act in order to prevent cool wind blowing within 2 mins 1 Heating starts 2 After Auto Defrost finished 3 Heating under the low temperature Gentle Breeze In the following situation the
22. l y change the way of chang e is Durin g the initia 2 5 seconds ten number s chang e in the one plac e of minute then the one place is constant ten number s chang e in the tens plac e of minute at 2 5 second s spee d and carry Durin g 5s blink pres s the Time r button the timer settin g succeeds The Timer On has been set up repres s the timer On button the Time r On will be canceled Befor e settin g the Timer pleas e adjus t the Cloc k to the curren t actua time Remote control SWING UP AND DOWN BUTTON TIMER OFF Press this button to set up swing angle TIMER OFF BUTTON which circularly changes as below Once press this key to enter into the TIMER OFF icon will blink OFF 3 J4 A The method of setting is the same as for TIMER ON I gt gt I gt Il TIMEROFF setup in which case A This is an universal use remote controller If remote controller sends the following three kinds of status that the swing status of main unit will be gt 7 y I lt gt I PE z When the guide louver start to swing up and down if turn off the Swing the air guide louver will stop at current position ll Sl which indicates the guide louver swings up and down between that all five positions 4 Operation of wireless remote control Guide for operation General operation 1 After powered on press ON OFF button the unit will start to run Not
23. mage the connection pipe the joint nut couldn t tighten too much otherwise it may cause leakage 21 e 4 Install outdoor unit C Electric wiring 1 Disassemble the handle on the outdoor unit right side plate 2 Take off wire clamp Connect and fix power connect Ha dle cord to terminal of line bank Wiring should fit that of indoor unit 3 Fix the power connection cable with wire clamp na 213 then connect the corresponding connector F blue black brown 4 Ensure wire has been fixed well 5 Install the handle l Indoor unit connection NOTE e Wrong wiring may cause spare parts malfunction e After the cable fixed make sure there should be a free space between the connection and connection and fixing place on the lead wire C Air purging and leakage test 1 Connect charging hose of manifold valve to charge end of low pressure valve both high low pressure valves must be tightly shut 2 Connect joint of charging hose to vacuum pump 3 Fully open handle handle of Lo manifold valve 4 Open the vacuum pump to evacuate At the beginning slightly loosen joint nut of low pressure valve to check if there is air coming inside If noise of vacuum pump has been changed the reading of multimeter is 0 Then tighten the nut 5 Keep evacuating for more than 15mins and make 2 Qin sure the reading of multi meter is 1 0 X 10 5 pa 76cmHg 6 Fully open high lo
24. tion where there should be sufficient ventilation 3 Select a location where there should be no obstructions cover the inlet and outlet vent 4 The location should be able to withstand the full weight and vibration of the outdoor unit and permit safe installation 5 Select a dry place but do not expose under the direct sunlight or strong wind 6 Make sure that the outdoor unit installation dimension should accord with installation dimension diagram convenient for maintenance repair 7 The height difference of connecting the tubing within 5m the length of connecting the tubing within 10m 8 Select a place where it is out of reach for the children 9 Select a place where will not block the passage and do not influence the city appearance 17 Notices for installation Safety Requirements For Electric Appliances The power supply should be used the rated voltage and AC exclusive circuit the power cable diameter should be satisfied Don t drag the power cable emphatically lt should be reliably earthed and it should be connected to the special earth device the installation work should be operated by the professional The air switch must have the functions of magnetic tripping and heat tripping in order to protect the short circuit and overloading 4 The min distance from the unit and combustive surface is 1 5m 5 The appliance shall be installed in accordance with national wiring regulations 6 An
25. to install Furthermore don t conn ect each wire to the gas pipe water pipe drainage pipe or any other impr oper places X Be sure to pull out the power plug when not using the air co nditioner for a long time Otherwise the accumulated dust may cause fire or electric shock X Select the most appropriate tem perature Pi er than outside auts e SNS It can preclude the electricity wasted Don t leave windows and doors open for a long time while operating the air conditioner It can decrease the air conditioning capacity Don t block the air intake or outlet vents of both the outdoor and indoor units It can decrease the air conditioning capacity or cause a malfunction Keep combustible spray away from the units more than 1m It can cause afire or explosion Please note whether the installed stand is firm enough or not If it is damaged it may lead to the fall of the unit and cause the injury Don t step on the top of the outdoor unit or place something As falling off the outdoor unit can be dangerous Don t attempt to repair the air conditioner by yourself The wrong repair will lead to an electric shock or fire so you should contact the service center to repair Notices for operation If the supply cord is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard The airflow
26. transmitter Remote control ON OFF ON OFF button Press this button the unit will be turned on press it once more the unit will be turned off When turning on or turning off the unit the Timer Sleep function will be canceled but the presetting time is still remained MODE button Press this button Auto Cool Dry Fan Heat mode can be selected circularly Auto mode is default while power on Under Auto mode the temperature will not be displayed Under Heat mode the initial value is28 KM 82 F Under other modes the initial valueis25 K 77 F N k lt SG AUTO COOL bs DRY S FAN XX HEAT only for cooling and heating unit SLEEP SLEEP button Press this button Sleep On and Sleep Off can be selected After powered on Sleep Off is defaulted After the unit is turned off the Sleep function is canceled After Sleep function set up the signal of Sleep will display In this mode the time of timer can be adjusted Under Fan and Auto modes this function is not available FAN button Press this button Auto Low Middle High speed can be circularly selected After powered on Auto fan speed is default Under Dehumidify mode Low fan speed only can be set up B nal al a Low fan a fl High fan Note Under the Dry mode the fan speed isn t adjustable low fan speed is imperative af Middle
27. uitable running method and to make ambient comfortable K About turbo function If start this function the unit will run at super high fan speed to cool or heat quickly so that the ambient temp approachs the preset temp as soon as possible Operation of wireless remote control X About lock Press and buttons simultaneously to lock or unlock the keyboard If the remote controller is locked the icon mm will be displayed on it in which case press any button the mark will flicker for three times If the keyboard is unlocked the mark will disappear X About swing up and down 1 Press swing up and down button continuously more than 2s the main unit will swing back and forth from up to down and then loosen the button the unit will stop swinging and present position of guide louver will be kept immediately 2 Under swing up and down mode when the status is switched from off tos if press this button again 2s later gt status will switch to off status directly if press this button again 7 within 2s the change of swing status will also depend on the circulation sequence stated above X About switch between Fahrenheit and Centigrade Under status of unit off press MODE and buttons simultaneously to switch C and F Changing batteries and notices 1 Slightly to press the place with J along the arrowhead direction to push the back cover of wireless remote control As show in figure 2 Take out the old batteries As sho
28. w in figure 3 Insert two new AAA1 5V dry batteries and pay attention to the polarity As show in figure 4 Attach the back cover of wireless remote control As show in figure A NOTE When changing the batteries do not use the old or different batteries otherwise it can cause the malfunction of the wireless remote control f the wireless remote control will not be used for a long time please take them out and don t let the leakage liquid damage the wireless remote control The operation should be in its receiving range it should be placed at where is 1m away from the TV set or stereo sound sets If the wireless remote control can not operate normally please take them out Sketch map for after 30s later and reinsert if they cannot normally run please change them changing batteries 10 4 Emergency operation C Displayer indicator light control of indoor unit It s a special selective buttonfor the users who are not accustomed to the light at sleeping e Get the displayer indicator light on When setting the light function the mark will display on the remote controller screen by pressing this button In which case the diss player indicator light will be on if the AC receives this signal eGet the displayer indicator light off If cancel the light function the mark Y will disap per on the remote controller screen by pressing this button In which case the displayer indicator li
29. w pressure valves 7 Remove charging hose from charging end of low pressure valve 8 Tighten bonnet of low pressure valve As shown in Fig 10 Fig 10 C Condensate drainage of outdoor unit no for cooling only The condensate and defrosting water formd during heating in the outdoor unit can be properly discharged by drainage pipe Installation method set the drain connection in 25 hole of thel 1 AH chassis has been installed and then connect drainage pipe 7 with drain nozzle so that condensate and defrosting waer can 6 Ch Chassis be properly discharged Drain connection 4 Check after installation and test operation Check after installation ltems to be checked Possible malfunction Has it been fixed firmly The unit may drop shake or emit noise Have you done the refrigerant leakage test lt may cause insufficient cooling heating capacity Is heat insulation sufficient lt may cause condensation and dripping Is water drainage well lt may cause condensation and dripping Is the voltage in accordance with the rated voltage marked on the nameplate It may cause electric malfunction or damage the part Is the electric wiring and piping connection installed correctly and securely It may cause electric malfunction or damage the part Has the unit been connected to a secure earth connection It may cause electrical leakage Is th
Download Pdf Manuals
Related Search