Barco DX-700 Graphics Tablet User Manual
Contents
1. e System Module e Input Module e Output Modules S 7 Ss N N N a N 7 7 7 a A Module a Raise the top latch until you can slide the module N w N N k kS 7 7 7 7 7 t EEATT farther into the chassis up to the latch s pivot point p A Pivot E atetetetetetalat at ett stata Point Tighten both retaining screws to secure the sseeeseeeeeeees module DX 700 Module Removal Ensure that DX 700 power is off Power Loosen both retaining screws on the module Connector Simultaneously push both latches away from the center of the module Always push both latches simultaneously CAUTION When both latches are clear of the chassis remove the module DX 700 Module Configuration Rules DX 700 supports a wide number of system configurations Input and output modules are installed in banks consisting of one or more input modules and either one or two output modules with two being the maximum allowed in a bank By definition a bank is a way of combining inputs and outputs into independent video processors that are capable of driving one or more LED walls In the most basic of DX 700 single bank configurations you must have at least one input module and one outpu2. S e 1 x SDI and 1 x HD SDI e 1 x Dual HD SDI m j I m JJ e m YOLINOW Use the Monitor Output EEE T BD van n tT San BEE Menu to set resolution and video source Both outputs show the same video Component Input Accepts Composite S Video and Component See the Format Connection Table m m m m o o e e ot 2 G JILSONDSVIG DVI Expansion Input Accepts single or dual DVI inputs with resolutions up to QXGA 2048 x 1536 with a Ethernet max 240 MHz pixel clock AR RADUT M Output Module connectors use proprietary a o ie for signals and pinouts Do not connect the eee OCS ok Diagnostic Port outputs to anything other than the inputs of communications Use the g Barco LED tiles Ethernet Menu to set For factory and technical parameters support use only DX 700 Module Insertion Ensure that DX 700 power is off 2 Orient the module so that the power connector is Retaining Screw Carefully insert the module and push it into the chassis until the module s top latch stops against the chassis Simultaneously push both latches towards the center of the module until the module is fully seated against the chassis Always push both latches CAUTION simultaneously oe Chassis at the bottom a Latch Rear View a
3. Management Menu in the final display e Use the Ethernet Menu to configure Ethernet parameters e Use the Setup Wizard to configure outputs and groups e Use the Monitor Setup Menu to set monitor output parameters test patterns and e Use the Input Wizard to configure inputs the monitor s video source e Use the Input Management Menu to fine tune inputs NNI Output Module DVI Output Module e Use the Genlock Menu to set the master sync source and individual bank Runs next generation LEDs Runs legacy LEDs Each genlock sources Each output is limited to output is limited to 1024 x 768 pixels 800 x 600 pixels Latches Used for precise insertion and DMX Control removal See the Module g Currently not implemented Insertion and Removal section LED Outputs LED Outputs m pa a Three HDMI type Three DVI I type 3 connectors are connectors are Genlock Inputs Expansion Out provided for NNI provided for DVI e Single connect Connects input modules for outputs outputs composite sync or external and cross bank black burst to H CS IN D stacking configurations only FHH m Separate connect H zZ HH x x and V sync to H CS IN 8 HH and V IN A RGBHV Input z E Accepts RGBHV inputs up to D z QXGA 2048 x 1536 with a Expansion Lock Out Z max 240 MHZ pixel clock For external stacking z w secs cormericebn o HD SDI Input F o fe to additional DX 700s Accepts S N ie e 2x SDI a e 2x HD SDI
4. They will be treated as spares Slots that do not contain modules must always have blank panels installed Storing Spare Modules outlined in the DX 700 Module Configure a bank according to the rules E Spares J3 F Bank 1 7 Configuration Rules section je ge ne w ple Install a blank panel immediately to the left of the bank s left most input module In the remaining slots insert spare modules These are ignored and treated as spares Format Connection Table Input Composite S Video YUV RGB Connector Video Y C YP P Sync on Green v v Luma v Luma Y G V Chroma Y Ps Vv B v P V R P N 26 0601004 00 Rev 02
5. DX 700 Quick Start Guide Barco Inc 11101 Trade Center Drive Rancho Cordova CA 95670 USA Customer Service Portal Phone 1 916 859 2500 Fax 1 916 859 2515 Technical Support 1 866 374 7878 www barco com esupport Website www barco com BARC Handles Two recessed handles are provided Chassis weight depends on the number of modules installed Focus The cyan focus can be moved with the Navigation buttons Softkeys Six softkeys activate functions or access menus Softkey labels appear in the Touch Screen s left hand column To operate press the Touch Screen button or the adjacent softkey Pri Quick System Setup The following list summarizes the overall DX 700 setup procedure For error free installation always refer to the listed section in the User s Guide gt Install and Cable LED Walls Ensure that your LED wall s are properly installed and cabled Rackmount DX 700 Ensure that the DX 700 is properly installed in your equipment rack Chapter 3 Rack Mount Installation Configure DX 700 Modules Ensure that all modules are installed in the proper configuration Chapter 2 Module Installation and Configuration Connect Sources and Signals Ensure that all sources and signals are properly connected Chapter 3 Signal Installation There are 3 ways to use the Touch Scre
6. e buttons do not work from within the Setup Wizard black Press again to restore the previous video Run the Input Wizard Use the Input Wizard to configure inputs and assign them to LED outputs Chapter 4 Using the Input Wizard Ensure that you save a preset after you configure each input Fine Tune Inputs Use the Input Management Menu to adjust brightness contrast color and more Chapter 4 Using the Input Management Menu Fine Tune Displays Use the Display Management Menu to adjust contrast gamma Fiberlink and more Chapter 4 Using the Display Management Menu Recall Presets Recall the desired preset and you re ready to begin production Chapter 4 Using the Preset Management Menu P N 26 0601004 00 Rev 02 Input Module Output Modules System Module RGBHV Monitor Out DVI Monitor Out DX 700 Input Modules provide the system s input Each module provides three outputs which can drive one The System module provides connections for Ethernet synchronization scaling and mixing functions Within each module the or more attached displays from any portion of a selected genlock monitoring DMX and diagnostics input source is selected from among the various input source image connectors and scaled to the required size and position Under the DX 700
7. en Press a button on the Touch Screen itself Press a softkey directly adjacent to a button in the Touch Screen s left hand column Use the arrows to move the cyan focus highlight Then press ENTER to activate 1 2 3 Setup Wizard Input Management Touch Screen Power On LEDs Fiberlink Turn on power to your LED walls and Fiberlink connections Power On DX 700 Turn on power to the DX 700 chassis Chapter 4 Power Up Initialization Factory Reset The first time you use a DX 700 or after a DX 700 returns from a show perform a Factory Reset Chapter 4 Performing a Factory Reset Calibrate Touch Screen Adjust display brightness and calibrate the Touch Screen Chapter 4 Using the Front Panel Display Adjust Menu Run the Setup Wizard Use the Setup Wizard to configure LED wall outputs and groups Chapter 4 Using the Setup Wizard Ensure that you set up all outputs and configure all output groups Navigation Use the arrows move the focus highlight and to scroll lists To activate a highlighted function press ENTER TEST PAT Press to access the Test Pattern Menu to assign test patterns to selected outputs PRESETS Press to access the Preset PRESETS i Management Menu to recall and manage presets BLACK Press to take all outputs to These thre
8. t module to route video to an LED wall always be an Output Module It must always be right justified against the System Module B As you face the rear of the chassis the right most module in the Input Output Section must Input Output Section B Input Output Section Correct Justification Incorrect Justification Within any bank all modules must be adjacent to each other with no blank panels in between and all Output Module s are always right justified Bank 1 Correct Justification Incorrect Justification DX 700 User s Guide For complete details on all installation setup configuration and operations procedures please refer to the DX 700 User s Guide E Bank 1 TT Bank 2 7 IMPORTANT installed on the Startup Diagnostic Menu you can press the DX 700 In multi bank configurations all banks must be directly adjacent to one another with no blank panels in between Correct Justification Incorrect Justification With the exception of spare modules if the DX 700 determines that any modules are incorrectly installed or missing a Startup Diagnostic Menu appears which prompts you to power down and re configure your modules If the above prompt occurs and provided that a System Module is properly Management button and access a subset of management functions The DX 700 will not recognize modules that are installed to the left of a blank panel
Download Pdf Manuals
Related Search