Barco 1219 Car Video System User Manual
Contents
1. 1219 User Manual Visibly yours pa SAFETY INSTRUCTIONS RISK OF ELECTRIC SHOCK DO NOT OPEN Read the safety and operating instructions before operating the apparatus Retain safety and operating instructions for future reference Adhere to all warnings on the apparatus and in the operating instructions manual Follow all instructions for operation and use This apparatus conforms to 0160950 cUL60950 IEC60950 CE FCC notice This equipment has been tested and found to comply with the limits of a class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR NO USER SERVICEABLE PARTS INSIDE REFER TO QUALIFIED SERVICE PERSONNEL in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This Class digital apparatus complies with Canadian ICES 003 Cet appareil num ri2. display guarantees perfect image quality in medical imaging applications The display combines a TFT thin film transistor liquid crystal display panel structure and a built in backlight with inverter for a better picture quality It is designed to meet users needs for performance consistency and outstanding image quality through a streamlined development process in which wall mount functionality provides a variety of capability The image on the display can be adjusted by means of the extended on screen menu system OSD The internal memory can contain settings for 24 different types of video signals with different timings 22 are factory preset 2 are user definable Multi scan capabilities display accepts the most common display standards However it is limited to the following specifications Analog video The horizontal frequency must be between 31 and 91 kHz the vertical frequency between 56 and 85 Hz Digital video The horizontal frequency must be between 31 47 and 64 kHz the vertical frequency between 60 and 70 Hz The optimum and recommended resolution is 1280 x 1024 60 Hz MFCD 1219 User s Guide 5 Power Saving The monitor comes with a power saving feature therefore you may put the monitor into a power saving state when it is not in use This feature complies with both EPA s Energy Star requirements and European NUTEK TCO s power management guidelines It conforms to Video Electronic
3. Input connectors 15 pin D sub for PC graphic signal input Mini DIN Power Connector for DC 12V 6 5A input DVI connector supporting DVI D only Power source 100 240 VAC Power consumption 50 W max Less than 5 W in power off mode Power saving VESA DPMS standard EPA Energy Star compliant PnP compatibility VESA DDC 2B standards compliant Safety standards UL60950 cUL60950 IEC60950 CE Dimensions W x H x D 450 mm x 461 8 mm x 213 9 mm MFCD 1219 User s Guide 18 Net weight 7 7 kg Operating Temperature 0 C to 40 C Storage Temperature 20 C to 60 C NOTICE DUE TO OUR POLICY OF CONTINUOUS PRODUCT IMPROVEMENT THE ABOVE SPECIFICATIONS ARE SUBJECTED TO CHANGE WITHOUT NOTICE BARCO SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES WHATSOEVER RESULTING FROM FURNISHING PERFORMANCE OR USE OF THIS MATERIAL MFCD 1219 User s Guide 19
4. child or adult and serious damage to the equipment CONTENTS a ok 5 wien 5 1 2 a e a 6 1 3 Controls 6 2 Installation is eet ee eee 8 2 1 PrOCAUTIONS 8 2 2 Wall MOUNTING ee eet 8 2 3 Connecting the 99 10 2 4 Starting UP 11 2 5 Install the DICOM Optimizer 11 3 On screen display OSD 12 3 1 How to use the 12 3 2 Description of the MENU ITEMS 13 Main MENU ete eee 13 Video Men 14 Color Menu wisi 15 Glock Menus 15 4 i ila on eee nates 16 Appendix A Possible 8 17 Appendix Technical 18 MFCD 1219 User s Guide 1 OVERVIEW 1 1 Introduction The MFCD 1219 BARCO s full color 19 LCD
5. connect the video 4 sync signals 1 Connect one end of the appropriate video cable to the corresponding video input of the monitor Analog video Connect to input 2 DVI Connect to input 3 2 Connect the other end of the video cable to the video output of your video source Analog video Computer graphics board with analog video output DVI Computer graphics board with digital video output To connect the power 1 Connect one end of the proper power cable to the AC input of the 12V DC adapter 2 Connect the 12V supply of the 12V DC adapter to the DC input 1 of the monitor 3 Connect the other end of the power cord to a grounded power outlet MFCD 1219 User s Guide 10 2 4 Starting up Proceed as follows 1 Switch on the computer 2 Switch on the display by pushing the Power key 8 3 If necessary select a suitable resolution in the computer operating system Please refer to Appendix A Possible resolutions in the back of this manual Note The recommended resolution for best image quality is 1280x1024 at 60 Hz The microcontroller in the display checks if the connected video signal has been adjusted before and if these adjustments have been stored in the memory There are 2 possibilities a The video signal has been adjusted and stored in the memory In this case the display switches to this memory location the so called mode and the image will need no further adjustme
6. 4 35 00 67 31 50 37 90 72 31 50 37 50 75 VESA 36 00 43 30 83 VESA 720 400 28 321 31 47 70 800 600 36 00 35 10 56 VESA 40 00 37 88 60 VESA 50 00 48 10 72 VESA 49 50 46 88 75 VESA 56 25 53 70 85 832 624 57 29 49 80 74 6 1024 768 65 00 48 36 60 VESA 75 00 56 50 70 VESA 78 80 60 02 75 VESA CRUS 80 60 24 75 94 50 68 70 85 VESA 1152 864 108 67 50 75 1280 1024 108 63 98 60 135 80 75 VESA 157 5 91 146 85 VESA 1219 User s Guide 17 APPENDIX TECHNICAL SPECIFICATIONS Picture panel 19 inch diagonal viewable screen TFT thin film transistor active matrix color liquid crystal display RGB interface Resolution 1280 x 1024 native Display area H x V 376 x 301 mm Pixel Pitch 0 294 mm H x 0 294 mm V Display color 16M Luminance 250 cd m typ Contrast ratio 500 1 typ Response time 25 ms Tr Td typ total Viewing angle Vertical 176 typ Horizontal 176 typ Input signals Analog Hor 31 47 to 91 2 kHz Vert 56 to 85 Hz Sync types Separate sync composite sync sync on Green Hor 31 47 to 64 kHz Vert 60 to 70 Hz Digital Max video input bandwidth 157 5 MHz Signal system Analog RGB signals digital Front panel controls Menu down decrease up increase Power
7. ighlight bar indicates the status of the mode RED indicates the function is selected and ready to be adjusted Blinking RED indicates OSD is in parameter adjusting mode Input type 1024 x 768 601 48 4 Resolution MFCD 1219 User s Guide 12 3 2 Description of the menu items Main menu Function Description Brightness To adjust the overall image and background brightness level Contrast To adjust the image brightness in relation to the background the background is unchanged Auto Adjust To automatically set the H Position V Position and Clock Horizontal Position To move the screen horizontally left or right Vertical Position To move the screen vertically upward or downward Color To adjust parameters for the screen colors of Red Green and Blue Clock To adjust the function only when characteristics are blurred Languages To select English French Italian German or Spanish for OSD language Input Type To select Analog A1 or DVI Digital D input source Lock Controls When locked the OSD menu will not appear when pressing the Menu key Cancel To restore the previous setting Save amp Exit To save the adjustments and quit the OSD menu Auto Adjust function will be automatically executed whenever the system is switched to a new mode When the system is changed to this mode again later on the system will
8. lation in case it is built in a rack or console Make sure computer and display are switched off before connecting the signals You can mount the panel to the wall instead of to the foot by means of the supplied mounting plate If you do not need to mount the panel to the wall please skip this item Step 1 Remove the panel from the foot 1 Position one hand under the panel the front side Position the other hand at the rear under the push button with BARCO logo 9 Firmly press down the push button 9 with one hand while carefully lifting the panel up with the other hand Remove the panel from the foot Step 2 Fix the mounting plate to the wall 1 Screw the mounting plate to the wall with the 4 supplied screws A MFCD 1219 User s Guide 8 Slide back the locks at both sides of the mounting plate B In that way you can secure the panel to the mounting plate after placing the panel 100 Step 3 Place panel the mounting plate Place the panel on the mounting plate If you want to secure the panel to the mounting plate place the panel in the frontmost notches Please make sure that the four shafts are securely placed in the notches of the mounting plate MFCD 1219 User s Guide 9 2 To secure the panel slide forward the locks on both sides of the mounting plate Lock the panel with one screw at both sides D 2 3 Connecting the signals To
9. llows 1 You must have installed the Barco NioWatch software 2 Right click on the NioWatch systray icon 3 Select Test Patterns from the pop up menu 4 Select the SMPTE test pattern 5 Now perform the function Autobalance from the MFCD 1219 control panel 6 When finished click on the test pattern to close it Function Description OSD Position To display the OSD to your preferred position Clock To adjust the function only when characteristics are blurred Clock Phase To adjust ADC sampling clock phase Main Menu To return to Main Menu MFCD 1219 User s Guide 15 4 MAINTENANCE Panel Take care not to damage or scratch the panel Clean with a soft woolen or cotton towel Use a watery solution or a mild commercial glass cleaning solution Cabinet Do not use chemical cleaning products benzene toluene xylene or other solvents Clean with a soft cloth dampened with mild detergent and water Repeat this with water only and wipe dry with a dry cloth MFCD 1219 User s Guide 16 APPENDIX A POSSIBLE RESOLUTIONS There are 22 preset modes and 2 user modes The following modes are preset as factory defaults Resolution Pixel Horizontal Vertical Standard Analog Digital Freq MHz Freq kHz Freq Hz 640 x 350 25 175 31 47 70 VGA 640 480 25 175 31 47 60 VGA VESA 30 2
10. not repeat the Auto Adjust function This function is only valid when the mode concerned is selected for the first time MFCD 1219 User s Guide 13 Color Menu Color Menu Down 1024 x 768 60 1 Up 48 4k To unlock the Controls proceed as follows 1 Press the Power key to switch off the display 2 With one hand press and hold the lt gt and the lt gt key at the same time With the other hand press the Power key shortly to switch the display on again 3 Keep holding the lt gt and the lt gt key for about 3 seconds 4 At last release the lt gt and the lt gt key Now by pressing the Menu key the OSD menu will appear Note The bottom line of the OSD shows the input type current resolution of the monitor and status of vertical sync If it shows user mode one of the user modes is selected Function Description Auto Balance To automatically adjust the contrast level of RGB This does not support resolution of Mac 832 x 624 at 75Hz R To adjust the level of color Red G To adjust the level of color Green B To adjust the level of color Blue Main Menu To return to Main Menu MFCD 1219 User s Guide 14 Clock Menu Clock Menu Down OSD Position Clock Clock Phase Main Menu 1 1024 x 768 60 1 48 4k To perform the Autobalance function you need to select a proper test pattern before performing the function Proceed as fo
11. nts b The video signal has not been adjusted and stored yet In this case the display will auto size the picture and store the settings in one of the user modes 2 5 Install the NioWatch software Proceed as follows Insert the CD ROM in the CD ROM drive The CD ROM starts automatically Please follow the instructions on the screen The CD ROM contains user instructions about the usage of the NioWatch MFCD 1219 User s Guide 11 3 ON SCREEN DISPLAY OSD MENUS 3 1 How to use the OSD Proceed as follows 1 Down Highlighted bar Press the Menu key 4 on the front to display the OSD main menu Note It may be possible that the OSD menu does not appear If this is the case the front Controls are locked To unlock them please follow the procedure described in 3 2 below Press the lt gt key 6 or lt gt key 5 to scroll to the desired menu item Press the Menu key 4 to activate the selected function or to enter the selected secondary menu If you have activated a function a Press the lt gt key 6 or lt gt key 5 to change the value b Press the Menu key 4 to enter the new value and return to the menu To exit the OSD while saving the changes select Save amp Exit To exit the OSD without saving the changes select Cancel Note The OSD disappears Up automatically after an inactivity period of 30 seconds The color of the h
12. que de laclasse B est conforme ala norme NMB 003 du Canada Power connection Warning This apparatus must be earthed Power requirements connect the apparatus to an AC voltage as indicated at its back Using a lower voltage the apparatus will notbe able to operate Using a higher voltage may damage the apparatus If you are not sure of the type of power supplied consult the power company Donot overload wall outlets and extension cords as this may result in fire or electric shock Mains lead protection U S Power cord Supply cords should be routed so that they are not likely to be walked 2005 BARCO nv Allrights reserved upon or pinched by items placed upon or againstthem paying particular attention to cords at plugs receptacles Water and moisture e Never expose the apparatus to rain or moisture Never use the apparatus near water e g near a bathtub washbasin swimming pool kitchen sink laundry tub or in a wet basement Ventilation Do not cover or block the ventilation openings in the cover of the set When installing the apparatus ina cupboard or another closed location heed the necessary space between the set and the sides of the cupboard Installation Place the apparatus flat solid and stable surface that can bear the weight of at least 3 monitors If you use an unstable cart or stand the set may fall causing serious injury to a
13. s Standard Association VESA approved DPMS power down signaling method This monitor automatically cuts down power consumption of monitor set when not detecting Hsync or Vsync signals This feature is compliant with VESA DPMS 1 2 Package contents The package should include the following items please check If some of the items are missing please contact the reseller you have purchased the unit from The display with foot 12V DC adapter European power cord American power cord UK power cord Video cables VGA cable and DVI D cable Mounting plate with 4 screws This user manual NioWatch CD ROM MFCD 1219 User s Guide 6 1 3 Controls and connectors 12V DC power input 1 2 Analog video input 3 DVI input DVI D supported only 4 Menu key 5 lt gt Key 6 lt gt 7 The LED is off when the display is off The LED is green when the display is on The LED is orange when the display is in power saving mode stand by Power key Push button to release the panel from the foot CSB MFCD 1219 User s Guide 7 2 INSTALLATION 2 1 Precautions 2 2 Wall mounting Keep your original packaging It is designed for this display and is the ideal protection during transport Avoid reflections in the flat panel to reduce eye strain Place the display on a strong and stable table or desk Keep the display away from heat sources and provide enough venti
Download Pdf Manuals
Related Search