Audiovox FPE2608 Flat Panel Television User Manual
Contents
1. wall outlet USING HEADPHONES down the volume before connecting headphones to the unit then adjust the volume to your desired level When headphones are connected no sound will come from front speakers E H TET NOTE Avoid listening to sound at high levels for prolonged periods of time This may be harmful to you and may cause hearing loss Headphones 1 8 3 5mm diameter plug PLV36320CS11 IB Eng 1 13 pmd 12 13 09 2007 17 27 PLV36320CS11 IB Eng 1 13 pmd 13 INSTALLATION REMOVING THE BASE STAND WARNING The LCD display is very fragile and must be protected at all times when removing the base stand Be sure that no hard or sharp objects or anything that could scratch or damage the LCD display come in contact with it Do NOT place pressure on the rear of the unit at anytime because the screen could crack 1 Disconnect any cables or cords connected to the unit 2 Lay the unit down on a flat surface so the back side is facing up making sure to place a soft cushioned material such as a blanket or thick piece of foam beneath the screen 3 Remove the 8 screws and then remove the BASE STAND fro2. NOTE aec A ld Please refer to the user ao manual for the other equipment for more information NO NS S gt S VIDEO IN jack VCR CAMCORDER SATELLITE SYSTEM CABLE etc To S VIDEO OUT AUDIO OUT jacks PLV36320CS11 IB Eng 1 13 pmd 8 13 09 2007 17 27 Satellite cable or TV oH To AUDIO IN jacks AV IN 1 CONNECTIONS CONNECTING DEVICES WITH A COMPOSITE YELLOW RCA TYPE VIDEO OUTPUT To connect A V devices such as a VCR video game system or camcorder Connecting to a VCR Video Game System Camcorder Connect the AUDIO VIDEO cable not included as shown Make sure you connect the cable from the other equipment AUDIO and VIDEO OUT to this unit AV IN 1 AUDIO and VIDEO IN or AV IN 2 AUDIO and VIDEO IN To AUDIO VIDEO IN jacks VCR VIDEO GAME SYSTEM 100010 tnam _ CAMCORDER t et CU Caec gt E etc To AUDIO VIDEO OUT jacks OR ii VIDEO IN SL VIDEO IN jacks AV IN 2 VCR VIDEO GAME SYSTEM CAMCORDER etc ant _ sou OUI BARI Esc mr TE AUDIO VIDEO
3. 14 19 Video Menu 14 WIG TMU EE E E 15 MORU 16 Setup ie inen cen time redo cette ime e tetti 17 18 Parental Men eio REND Ere ape FEE ERG ae E re Rs 18 19 TROUBLESHOOTING GUIDE sez 20 PLV36320CS11 IB Eng 1 13 pmd 3 13 09 2007 17 27 ACCESSORIES Please check and identify the supplied accessories Remote Control with batteries nennen nennen nennen 1 GETTING STARTED USING THE REMOTE CONTROL Point the remote control at the remote sensor located on the unit When there is a strong ambient light source the performance of the infrared remote sensor may be degraded causing unreliable operation The recommended effective distance for remote operation is about 16 feet 5 meters TO INSTALL BATTERIES 1 Open the battery door 2 Insert 2 AAA batteries BATTERY REPLACEMENT When the batteries become weak the operating distance of the remote control is greatly reduced and you will need to replace the batteries CAUTION Danger of explosion if battery is incorrectly replaced NOTES f the remote control is not going to be used for a long time remove the batteries to avoid damage caused by battery leakage corros
4. mM A ems 5 Ems e mE SETTINGS IN PC MODE Video Video Ed mM 3 3 T lt gt Select EXIT Exit lt gt Select EXIT Return Picture Mode Brightness Contrast Saturation Tint Sharpness Color Temperature H Position V Position Phase Clock Select from preset screen display settings to match the type of show you are watching Personal Soft Movie Standard amp Dynamic Select Personal mode to recall your customed settings on brightness contrast saturation tint sharpness and color temperature Adjust the brightness of the picture Brighten or darken the whole picture Adjust to sharpen the picture quality The black portions of the picture become richer in darkness and the white become brighter Adjust the color saturation of the picture Adjust the tint of the picture Toward purple Toward green Adjust the sharpness level to improve detail in the picture Adjust the three color temperature of the picture Choose from Standard balanced Warm red white or Cool blue white modes Center the image by moving it left or right Center the image by moving it up or down Adjusts the image if there is flicker of screen letters color misalignment or blurring Adjusts the display clock to change width of the image Resolution
5. AUDIOVOX ELECTRONICS CORP FPE3208 32 HD FLAT PANEL LCD TV OWNER S MANUAL Homer FOR ASSISTANCE CALL CUSTOMER SERVICE AT 1 800 645 4994 OR VISIT US AT WWW AUDIOVOX COM 128 XXXX PLV36320CS11 AUDIOVOX lt P N 811 363291W010 gt English SIZE 148 X 210MM MATERIAL 809 WOODSFREE PAPER PLV36320CS11 IB Eng 1 13 pmd 1 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE AVIS RISQUE DE CHOC LECTRIQUE NE PAS OUVRIR WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USERSERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL a The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance n The symbol for Class II Double Insulation CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT OF WA
6. AUDIO jack PC IN 21 AUDIO IN Left Right jacks AV IN 1 15 COMPONENT VIDEO IN Y PB PR 22 S VIDEO jack AV IN 1 23 AUDIO IN Left Right jacks YUV IN lt lt CONNECTIONS CONNECTING A TV ANTENNA CABLE SATELLITE To view television channels correctly a signal must be received from one of the following sources An indoor or outdoor aerial antenna A cable system A satellite system Connecting a Digital Antenna The tuner in this TV receives ATSC TV signals from an antenna This digital TV can receive standard SDTV and high definition HDTV over the air broadcasts Connecting an Analog Antenna or Device The tuner in this TV receives NTSC TV signals analog cable signals or the RF output from a satellite receiver VCR or cable box antenna cable to TV ANTENNA terminal cable not included CONNECTING AN A V DEVICE To connect to other equipment such as a VCR camcorder satellite system or cable etc Connecting to a VCR Camcorder Satellite System Cable Connect the AUDIO and S VIDEO cable not included as shown Make sure you connect the cable from the other equipment AUDIO OUT and S VIDEO OUT to this unit AV IN 1 AUDIO IN and S VIDEO IN
7. Music FORMAT Button Press to select the picture format 13 09 2007 17 27 CONTROL REFERENCE GUIDE FRONT amp SIDE VIEWS Ulf UN 1 STD BY ON button 7 Color LCD screen e Turns the unit on and off 8 Remote sensor e 2 MENU button Receives the remote control signal Enters the on screen TV menu Standby indicator 3 FUNCTION button 9 Speaker Selects TV AV 1 AV 2 YUV in HDMI 1 HDMI 2 PC in 4 CH buttons Confirms selections on the TV menu screen and changes the TV channels 5 VOL controls Adjusts the volume level 6 Removable stand PLV36320CS11 IB Eng 1 13 pmd 6 13 09 2007 17 27 HN IIS PLV36320CS11 IB Eng 1 13 pmd 4 10 11 12 13 14 15 10 VIDEO OUT jack AV OUT jacks YUV IN CONTROL REFERENCE GUIDE REAR VIEW i e iii G 18 19 20 21 22 23 18 VIDEO IN jack AV IN 1 19 PHONES jack 20 TV ANTENNA terminal 13 09 2007 17 27 16 AUDIO IN Left Right jacks AV IN 2 AUDIO OUT Left Right jacks AVOUT 17 jack AV IN 2 11 MONITOR VGA jack PC IN 12 AC Power Cord 13 HDMI IN jacks HDMI IN 1 HDMI IN 2 14
8. OSD Language Time Setup Caption Restore setting w Restore setting gt Eun IZ Select EXIT Exit HDMI PC MODE OSD Language Select from English Espafiol Frangais OSD Language English o gt Time Setup X Parental 4 Select Bu Time Setup Setting Time Update 4 Video audio Cum Off 4 Power On Time Power OffTime 7 Time Setup ENTER Enter lt gt Select EXIT Return ENTER Enter lt gt Select EXIT Return Time Zone Select the time zone from Eastern Time Indiana Central Time Mountain Time Arizona Pacific Time Alaska Hawaii Sleep Timer Select the time to turn the unit to Standby mode automatically Off gt 5 Minutes gt 10 Minutes gt 15 Minutes gt 30 Minutes gt 60 Minutes gt 90 Minutes gt 120 Minutes gt Off When you set the Time the option will be shown Time Update Select On Off to activate the following manual settings Select Auto to synchronize time with the digital TV channel signal Date Press the 4 or button to locate the position and press the number buttons to input date Time Press the lt or gt button to locate the position and press the number buttons to input time Timer Select On to activate automatically power on off Power On Time Press the 4 or gt button to locate the position and press the number buttons to input ower on time Power Of
9. 1 366 x 768 max PLV36320CS11_IB_Eng_14 21 pmd E 14 14 13 09 2007 14 59 e ID Te TT e TV SETUP AUDIO MENU 1 Press the MENU button 2 Use the A or button to select Audio then press the ENTER or button to go into the Audio settings 3 Use the A or button to select the options Balance Bass Treble Virtual Surround Reverb or Sound mode Adjust them using the lt or button The screen will change to your desired setting or press the ENTER or button to go into the detailed settings 4 Press the EXIT button to return to the previous menu 5 Repeat steps 3 and 4 to adjust other options 6 To exit the MAIN MENU and return to the normal screen press the EXIT button repeatedly TV MODE Audio li Z1 Experiment with different sound settings until you find the settings you prefer Balance Adjust the balance level toward the left or right speakers Adjust the bass range Treble Adjust the treble range Virtual Surround Switch on or off the virtual surround effect Reverb Select from preset sound settings Concert Living Room Hall Arena Church AV YUV HDMI PC MODE A gt Audio EE as xd NEN 4 gt EXIT Exit Off to match the type of show you are watching Sound mode Select from preset sound settings Standard Personal Theater Voice amp Music to mat
10. LL OUTLET THEN FULLY INSERT USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED MAY RESULT IN HAZARDOUS RADIATION EXPOSURE WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE DONOT PLACE OBJECTS FILLED WITH LIQUIDS ON OR NEAR THIS UNIT SHOULDANY TROUBLE OCCUR DISCONNECT THEAC POWER CORD AND REFER SERVICING TOAQUALIFIED TECHNICIAN WARNING Changes or modifications to this unit not expressly approved by party responsible for compliance could void the user authority to operate the unit PLACEMENT INFORMATION Do not use this unit in places which are extremely hot cold dusty or humid Do not restrict the air flow of this unit by placing it somewhere with poor air flow by covering it with a cloth by placing it on bedding or carpeting SAFETY INFORMATION When connecting or disconnecting the AC power cord grip the plug and not the cord itself Pulling the cord may damage it and create a hazard When you are not going to use the unit for a long period of time disconnect the AC power cord CONDENSATION INFORMATION When left in a heated room where it is warm and damp water droplets or condensation may form inside the equipment When there is condensation inside the unit the unit may not function normally Let the unit stand for 1 2 hours before turning the power on or gradually heat the room and let the unit dry before us
11. Press the ENTER or gt button to confirm The menu locked screen will be displayed 3 Enter a 4 digit password Once entered the screen will enter the Parental menu The preset password is 0000 You can edit the parental control level or change the password See Parental Control Settings on the next page TV MODE AV YUV PC MODE video video audio audio amp Setup DET Parental 4 gt Select EXIT Exit Parental lt gt Select EXIT Exit If you forget the password enter 8888 to unlock parental control E 18 PLV36320CS11_IB_Eng_14 21 pmd 18 13 09 2007 14 59 TV SETUP Parental Control Setting 1 Use the A or Y button to select various Parental settings Press the ENTER button to go into the detailed settings 2 Use the A Y buttons to move among the rating levels Press the ENTER button to change the mode between Blocked and Allowed 3 Press the EXIT button to return to the previous menu 4 Repeat steps 1 3 to adjust other options 5 To exit the MAIN MENU and return to the normal screen press the EXIT button repeatedly Parental gt Parental E721 Select EXIT Return Program Block E2231 Select EXIT Return Rating Enable Select On to edit the following parental items Select Off to disable parental control Open V Chip Reads the ratings from ATSC TV programs if the
12. apparatus has been exposed to rain or moisture does not operate normally or has been dropped 13 09 2007 17 27 CONTENTS SAFETY PRECAUTIONS IMPORTANT SAFETY INSTRUCTIONS eiue eeeieese eene nn enn nn snam etna tna tnam stat natn atnsnasn en 2 3 Dieezillo l 4 GETTING CONTROL REFERENCE GUIDE x cpP Connecting a TV Antenna Cable Satellite 2 8 Connecting an A 7 V Device te ete d petet tud 8 Connecting Devices with a Composite Yellow RCA Type Video Output 9 Connecting Devices with a Composite Yellow RCA Type Video 9 Connecting a High Definition HD Source 10 Connecting a BO anode eroe t 10 Connecting inire dea n ee ote 11 Connecting an Audio Amplifier tee Ee Cede de brad 11 Connecting the AC Power 12 USING HEADPHONES U Removing the Base Stand eeepc de Nc e e D eade b data 13 Wal 13
13. ch the type of show you are watching Select Personal mode to recall your custom settings on bass and treble PLV36320CS11_IB_Eng_14 21 pmd 15 15 13 09 2007 14 59 TV SETUP TV MENU For TV Mode Only 1 Press the MENU button 2 Use the A or button to select TV Press the ENTER button to go into the TV settings 3 Use the A or button to select the options Tuner Mode Auto Scan Auto Scan Add CH Channel Skip MTS or Audio Language Adjust them using the 4 or button The screen will change to your desired setting or press the ENTER or button to go into the detailed settings 4 Press the EXIT button to return to the previous menu 5 Repeat steps 3 and 4 to adjust other options 6 To exit the MAIN MENU and return to the normal screen press the EXIT button repeatedly Tuner Mode Antenna over the air broadcasts Ch 2 69 or Cable cable satellite broadcasts CH 1 135 mode is available Auto Scan Searches for usable stations and stores them in memory Auto Scan Add CH Searches for more usable stations and adds them in memory The stations stored before are still kept Channel Skip Skip weak channels and the channels you do not like MTS Select from Stereo SAP Secondary Audio Program Mono Audio Language Select from English Spanish French Available for digital channels if multiple audio languages are broadcasted NOTE The SAP Seco
14. e RATING PLATE LOCATION The rating plate is located on the rear of unit FCC STATEMENTS NOTE This unit has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This unit generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference 10 radio communication However there is not guarantee that interference will not occur in a particular installation If this unit does cause harmful interference to radio or television reception which can be determined by turning the unit off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the unit and receiver Connect the unit into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 13 09 2007 17 27 e ID IMPORTANT SAFETY INSTRUCTIONS 1 2 3 4 5 6 7 8 9 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with a dry cloth Do not block any
15. e sure your TV supports HDCP High Bandwidth Digital Content Protection 13 09 2007 14 59 i Unit INCH PLV36320CS11 IB Eng 14 21 pmd 31 5 8 co J SUIT ae TT NEAN 11 7 8 19 3 4 i Print in China 811 363291W010 13 09 2007 14 59
16. ed as shown Make sure you connect the cable from the other equipment AUDIO IN to this unit AUDIO OUT PLV36320CS11 IB Eng 1 13 pmd 11 HI um T a VIDEO AV OUT OUT r AUDIO 4 OUT 4 HS 1f lo Sor 27 ej ToAUDIO OUT jacks AUDIO AMPLIFIER EXTERNAL SPEAKERS To AUDIO IN jacks E 11 13 09 2007 17 27 CONNECTIONS CONNECTING THE AC POWER CORD Connect the AC power cord into a wall outlet Press the STD BY ON button on the left side of the unit or use the remote control to turn on the unit NOTES TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT OF WALL OUTLET THEN FULLY INSERT SM When the AC power cord is 0 mg 0 plugged in the unit is not completely disconnected from the main power even when the power is turned off Be sure the AC power cord is disconnected and functions are off before making connections l IINE components are connected Make sure that all the correctly When you are not going to use the unit for a long period of time disconnect the AC power cord
17. f Time Press the 4 or button to locate the position and press the number buttons to input power off time E 17 PLV36320CS11 IB Eng 14 21 pmd 17 13 09 2007 14 59 TV SETUP Caption Setting Caption Style Broadcaster 4 Font Size Small Font Style Style 1 Font Color Green Font Opacity Solid Background Color Black Background Opacity Translucent 4 Window Color White 4 Window Opacity Transparent lt gt Video Analog Closed Caption Digital Closed Caption Audio Digital Caption Style 2 W Parental Digital Caption Style lt gt Caption ENTER Enter 4 gt Select EXIT Return Analog Closed Caption Select the analog closed caption or turn it off Digital Closed Caption Select the digital closed caption or turn it off Digital Caption Style Select as Broadcaster to use the default digital caption style of the broadcaster Select Custom to activate the caption style items and set you preferred detailed settings NOTE This function only works on ATSC programs broadcast with captions Restore Setting If you reset the TV to the factory settings all your present settings on Video amp Audio will be erased and replaced by the factory s default settings However picture settings in PC mode and Parental settings will not be erased PARENTAL MENU Password 1 Press the MENU button 2 Use the A or button to select Parental
18. gt OUT jacks NOTE Please refer to the user manual for the other equipment for more information CONNECTING DEVICES WITH A COMPOSITE YELLOW RCA TYPE VIDEO INPUT To connect A V devices such as a VCR PVR or camcorder Connecting to a VCR SERRE EE LIP PVR Camcorder Connect the AUDIO VIDEO cable not included as shown ol 05 Make sure you connect the ae cable from the other equipment our 1 T AUDIO PUTET 6 2 unit AUDIO and VIDEO OUT P NOTE Please refer to the user manual for the other equipment for more information VCR PVR CAMCORDER etc To AUDIO VIDEO IN jacks E 9 PLV36320CS11 IB Eng 1 13 pmd 9 13 09 2007 17 27 lt lt CONNECTIONS CONNECTING A HIGH DEFINITION HD SOURCE High Definition HD Devices with component video output must be Connect the component video cable and audio cable not included Make sure you connect the component video cable and audio cable from the other equipment COMPONENT VIDEO OUT and AUDIO OUT to this unit COMPONENT VIDEO IN and AUDIO IN YUV IN WI ToAUDIO IN jacks YUV IN LEGO eA oec r um May requi
19. ion Do not mix old and new batteries Do not mix ALKALINE standard CARBON ZINC or rechargeable NICKEL CADMIUM batteries Always remove batteries as soon as they become weak Weak batteries can leak and severely damage the remote control WARNING Do not dispose of batteries in a fire Batteries may explode or leak A WARNING Do not dispose of batteries in a fire Batteries may explode or leak Many universal remote controls have a learning feature We recommend you use that feature to program the remote control For any questions or problems related to programming a universal remote control you must contact the customer service department of the universal remote control manufacturer for assistance or refer to the instructions included with the universal remote control We cannot offer assistance in programming universal remote controls E 4 PLV36320CS11 IB Eng 1 13 pmd 4 13 09 2007 17 27 CONTROL REFERENCE GUIDE REMOTE CONTROL 1 STANDBY ON button Press to turn ON the unit or put it in STANDBY OFF mode TV button Press to switch to TV mode button Press to switch to source connected to AV 1 AV 2 composite inputs HD button Press to switch to source connected to YUV component inputs and HDMI 1 HDMI 2 inputs DISPLAY button Press to change disc status information displayed on the screen Number 0 9 buttons dot butto
20. m the unit E NU Tra 00020000000200000000001 MOUNTING ON THE WALL This unit is VESA compliant and is designed to be wall mounted with a VESA compliant 7 7 8 x 7 7 8 200mm x 200mm mounting kit designed for flat panel TVs sold separately Mount this unit according to the directions included with the mounting kit NOTE Remove the base stand before mounting the unit on the wall N S Fourmountig 000010 13 09 2007 17 27 VIDEO MENU 1 Press the MENU button 2 Press the ENTER or gt button to select Video 3 Use the A or Y button to select the options Picture Mode Brightness Contrast Saturation Tint Sharpness or Color Temperature Adjust them using the 4 or button The screen will change to your desired setting or press the ENTER or gt button to go into the detailed settings 4 Press the EXIT button TV SETUP to return to the previous menu 5 Repeat steps 3 and 4 to adjust other options 6 To exit the MAIN MENU and return to the normal screen press the EXIT button repeatedly TV MODE AV YUV HDMI MODE Video Video
21. n Use to enter digital sub channels i e 11 3 or 12 7 10 11 12 13 14 15 16 17 18 PLV36320CS11 IB Eng 1 13 pmd 5 MENU button Press to display the on screen TV menu VOLUME buttons Press to adjust the volume level CURSOR v lt gt buttons Press to highlight selections on a menu screen and adjust certain settings ENTER button Press to confirm selections on a menu Screen CC button Press to activate the Closed Captioning feature This function only works on programs broadcasted with captions EXIT button Press to exit the TV SET UP menu and return directly to normal viewing SLEEP button Press to set the SLEEP timer The unit will remain on for the time that is set and will automatically shut off afterwards FUNCTION button Press to switch between TV AV 1 AV 2 YUV in HDMI 1 HDMI 2 PC in LAST CH button Press to switch repeatedly between the last two channels displayed MUTE button Press to turn off the sound CH CH buttons Press to change the channels MTS buttom Press to switch between MONO sound STEREO sound and Secondary Audio Program SAP PICTURE button Select from preset screen display settings to match the type of show you are watching Personal Soft Movie Standard Dynamic SOUND button Press to select from preset sound settings to match the type of show you are watching Standard Personal Theater Voice
22. ndary Audio Program feature allows a TV station to broadcast other information which could be audio in another language Channel Skip Setting 1 Use the A or button to select a channel Press the button to select the last channel of the page press again to go to the next page Press the 4 button to select the first channel of the page press again to go to the previous page 2 Press the ENTER button to shift between skip or not skip the channel y appears in the square means skip the selected channel The channel will not appear when you press the CH CH Button se Channel Skip Eu gt Select EXIT Return E 16 PLV36320CS11_IB_Eng_14 21 pmd 16 13 09 2007 14 59 TV SETUP SETUP MENU 1 Press the MENU button 2 Use the A or button to select Setup Press the ENTER or gt button to go into the Setup settings 3 Use the A or button to select the options OSD Language Time Setup Caption or Restore setting Adjust them using the 4 or button The screen will change to your desired setting or press the ENTER or gt button to go into the detailed settings 4 Press the EXIT button to return to the previous menu 5 Repeat steps 3 and 4 to adjust other options 6 To exit the MAIN MENU and return to the normal screen press the EXIT button repeatedly TV MODE YUV MODE video audio OSD Language Time Setup Caption
23. ple images distortion blurry Black and white picture No picture or sound Colored patches of picture No sound is output from the HDMI out TROUBLESHOOTING GUIDE CAUSE AND REMEDY Check that the AC power cord is connected The unit is not turned on Remove any obstacles between the remote and the unit Use the remote near the unit Point the remote at the remote sensor on the unit Replace the batteries in the remote with new ones Check the location of the antenna and adjust it if necessary Make sure the antenna cable is firmly connected Make sure all input cables are firmly connected Check the VIDEO MENU within the TV SETUP MENU Check to make sure the program you are watching is broadcast in color and not black amp white Make sure the unit is plugged in and turned on Make sure that TV mode is selected Try a new channel to check for possible station trouble Make sure the antenna is connected properly Increase the volume Make sure the antenna or audio video source device is working properly Make sure all cables are firmly connected Check for local interference Make sure there are no unshielded electrical devices nearby that are causing interference Turn the unit off for 30 minutes then try it again Check the connection between this unit and the HDMI out jack of other equipment See if the TV supports this 480p 576p 720p 1080i DVD system Check your TV system setup correctly Mak
24. re a subscription To for receiving HD channels Check with your cable satellite service provider for Jacks details KUVIN NOTE When connecting a DVD player to the television the picture resolution is solely dependent upon the connected to the YUV input as shown HD SOURCE With component video output Digital Cable Box Satellite Receiver or external over the air HD Tuner To AUDIO OUT jacks p e ttt To COMPONENT VIDEO OUT jacks resolution supported by the DVD player attached DVD player resolutions vary from 480i to 1080i and this unit can support DVD players up to a maximum resolution of 1080i CONNECTING A PC Connect the 15 pin D SUB PC VGA input on this unit using monitor cable and audio cable not included as shown computer to the 15 pin D SUB PC 0 0 0 VGA connector from your 2n 3 Make sure you connect the cable from the computer gt TTT TROC ll Y w 0000 Connector and PC AUDIO to _ co STIL this unit PC IN MONITOR VGA and AUDIO E 10 PLV36320CS11 IB Eng 1 13 pmd 10 To PC AUDIO OUT jack p To PC connector 13 09 2007 17 27 CONNECTING HDMI High Definition Multimedia Interface
25. re is rating information broadcasted and denies the channel when its rating is higher than the ratings you pre set U S Recommended for all children TV Recommended for all children age 7 and above Ratings General Audience Parental Guidance Suggested Parental Strongly Cautioned Mature Audience Only U S GENERAL AUDIENCES Suitable for all ages Movie PARENTAL GUIDANCE SUGGESTED Some material may not be suitable for Ratings children PARENTS STRONGLY CAUTIONED Some material may be inappropriate for children under 13 RESTRICTED Under 17 requires accompanying parent or adult guardian for viewing in movie theaters No one 17 or under admitted in movie theaters Adults Only Canadian Children English Recommended for children age 8 and older Ratings GENERAL AUDIENCES Suitable for all ages PARENTAL GUIDANCE SUGGESTED Some material may not be suitable for children Viewers 14 years and older Adult Programming Canadian GENERAL AUDIENCES Suitable for all ages French 8 ans Not recommended for young children Ratings 13 Not suitable for children under the age of 13 16 Not suitable for children under the age of 16 18 ans Adult Programming E 19 PLV36320CS11 IB Eng 14 21 pmd 19 13 09 2007 14 59 PLV36320CS11 IB Eng 14 21 pmd SYMPTOM No power The remote does not function TV Bad Picture snow multi
26. supports both video and audio on a single digital connection for use with DVD players DTV set top boxes and other digital AV devices HDMI was developed to provide the technologies of High Bandwidth Digital Content Protection HDCP as well as Digital Visual Interface DVI in one specification HDCP is used to protect digital content transmitted and received by CONNECTIONS DVI compliant or HDMI compliant displays HDMI has the capability to support standard enhanced or high definition video plus standard to multi channel surround sound audio HDMI features include uncompressed digital video a bandwidth of up to 2 2 gigabytes per second with HDTV signals one connector instead of several cables and connectors and communication between the AV source and AV devices such as DTVs HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC Connect the HDMI cable not included as shown Make sure you connect the cable from the source equipment HDMI OUT to this unit HDMI IN Press the HD button to match the video source output quality TI LL To HDMI IN jack CONNECTING AUDIO AMPLIFIER This connection allows you to use an audio amplifier and external speakers Connect the AUDIO cable not includ
27. ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus Including amplifiers that produce heat Do not defect the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your safety If the provided plug does not fit into your wall outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand PLV36320CS11 IB Eng 1 13 pmd 2 tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over cy 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any Way such as the power cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the
Download Pdf Manuals
Related Search