Audiovox AVXMTG10U DVD Player User Manual
Contents
1. 10 Inch Roof Mount DVD Player With DVD CD MP3 SYSTEM Audio vox AVXMTG1OU INSTALLATION GUIDE TABLE OF CONTENTS Important Notices Materials Included in this Package Removing and Installing Snap On Covers General Vehicle Installation Approach Connecting the Dome Lights ONAWHN IMPORTANT NOTICES Installation of overhead products requires careful planning and preparation Be extremely careful when working on a vehicle with side curtain air bags Do not route wires near any portion of the side curtain air bag assemblies This includes anchor points in A B C or D pillars of the vehicle Routing wires in these areas or running wires by the side curtain air bags can prevent the side curtain air bag from fully deploying which can result in personal injury to vehicle occupants If you have any guestion regarding routing in a vehicle please contact Audiovox Technical support at 1 800 225 6074 An LCD panel and or video monitor may be installed in a motor vehicle and visible to the driver only if the LCD panel or video monitor is used for vehicle information system control rear or side observation or navigation If the LCD panel or video monitor is used for television reception video or DVD play the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in park or when the vehicle s parking brake is applied When connecting power and ground in a mobile2. NECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle s wiring There are two common types of dome light circuits used positive or negative switched Positive systems supply voltage to the interior lights to turn them on Negative switched systems apply ground to illuminate the bulbs To determine which system you have you must locate the wires at the dome light On a positive switched system with all the doors closed and lights out both wires at the dome light will rest at ground When the light is activated one of these wires will switch to 12 VDC This is the vehicle s switching wire On a negative switched system with all the doors closed and lights out both wires at the dome light will rest at 12 VDC When the light is activated one of these wires will switch to ground This is the switching wire For positive systems connect the purple brown Lamp auto wire to the vehicle s switched wire Then connect the red black Lamp on wire to a fused constant 12 volt source and the black red Lamp common wire to a good ground Positive systems are commonly found on Ford vehicles For negative systems connect the purple brown Lamp auto wire to the vehicle s switched wire Then connect the red black Lamp on wire to a good ground and the black red Lamp common wire to fused constant 12 volt source Negative systems are commonly found on General Motors and import vehicles Note Some vehicles w
3. e individual components and accessory options being installed Ensure that the wiring is protected from sharp edges Ensure that all wiring is not pinched when all components and interio trim are fully installed Leave enough slackin the wiring at each component to allow working room 6 Remove all A V system components from their packaging and place them loosely in the vehicle at their respective locations 7 Connect all components together and verify the proper operation of all system functions Note This is best done BEFORE components have been permanently mounted 8 After verifying proper operation of the system proceed to mount each component 9 When all components are mounted recheck the function of the entire system Ensure that no wiring was pinched or connected improperly during final installation RD NO is GENERAL VEHICLE INSTALLATION APPROACH Installing Unit to Roof Roof LS Roof Support Headliner l Mounting Bracket 4 Self drilling Screws aa Il Video Unit L L M5 Screw GENERAL VEHICLE INSTALLATION APPROACH oo o a TD Sa a o Weld nd o Xx li 2 To Dome Lights See Connecting the Dome Lights 6 Pin Power Harness FE 2 Pin Power Wire Harness with Choke Optional Relay Box ER Signal Harness AVIN 3 RCA Jack Pigtail CON
4. een and snap on screen cover at locations A B and C and gently pry the cover away from the screen Installing the Screen Cover 1 Open the LCD screen 2 Hook the two tabs D at the bottom edge of the screen cover into the notches on the bottom edge of the LCD screen 3 Snap the opposite side of the screen cover over the hinges Disconnecting the Shroud aa 1 Open the LCD screen Insert the supplied pry tool between the unit and shroud at fastener location E and gently pry the shroud away from the unit gt Installing the Shroud TS vers LL Expanded view 1 Open the LCD screen 2 Slide the shroud over the unit The shroud will snap into place at locations F GENERAL VEHICLE INSTALLATION APPROACH Decide upon the system configuration and options that will be installed Review all manuals to become familiar with electrical requirements and hookups Decide upon the mounting locations of all components and the method of mounting Prep the vehicle Remove any interior trim necessary to gain access to vehicle s wiring as well as all areas where interconnecting wire harnesses will be located If any access holes need to be cut into the vehicle do this now 5 Route the wiring harnesses in the vehicle as necessary Refer to the wiring diagrams in this manual as well as the wiring instructions for th
5. hich incorporate transistorized control of the dome light circuit such as the 1999 Dodge Caravan may reguire that the purple brown Lamp auto wire be connected to the door pin switch wire as the additional current draw of the Monitor s lights may not be supported by the output of the vehicle s body control computer Positive Switched Dome Lighting To 6 pin Red black Lamp on To connector Blaek reddlamo constant on Monitor 12 VDC common Purple brown Lamp Auto To constant 12 VDC Factory Door Ajar Switch or Body Control Computer Negative Switched Dome Lighting To Red black Lamp on connector Black red Lamp common Purple brown Lamp Auto To constant 12 VDC To constant 12 VDC Factory Door Ajar Switch or Body Control Computer This page intentionally left blank ES 7 For Customer Service Visit Our Website At www mobile audiovox com Product Information Photos FAG s Owner s Manuals 9 2010 AUDIOVOX 150 Marcus Blvd Hauppauge NY 11788 128 8902
6. video installation insure that the ACC wire is fused at the point where it is connected to the vehicle s ACC wiring Failure to do so can result in damage to the vehicle if a short circuit develops between the vehicle connection point and the mobile video product An LCD panel and or video monitor used for television reception video or DVD play that operates when the vehicle is in gear or when the parking brake is not applied must be installed to the rear of the driver seat where it will not be visible directly or indirectly to the operator of the motor vehicle WARNINGS Do not use any solvents or cleaning materials when cleaning the video monitor Do not use any abrasive cleaners they may scratch the screen Use only lightly dampened lint free cloth to wipe the screen if it is dirty Lock the LCD screen in fully closed position when not in use Before putting on headphones always adjust the volume setting to OFF or owest position Remember to leave the dome light switch in the off or auto position when he vehicle is unattended as the dome lights if left on can drain the vehicle battery Do not put pressure on the screen Caution children to avoid touching or scratching the screen as it may become dirty or damaged Safety Precautions For safety reasons when changing video media it is recommended that the vehicle is not in motion and that you do not allow children to unfasten seat belts to change
7. video media or make any adjustments to the system System adjustments can be accomplished using the remote control while seat belts remain fastened Enjoy your AUDIOVOX entertainment system but remember that the safety of all passengers remains the number one priority Licensed under one or more of the following patents Patent Numbers 5 775 762 5 927 784 and 6 678 892 MATERIALS INCLUDED IN THIS PACKAGE 1 10 LCD Overhead Monitor with DVD player 1 pc 2 6 Pin Power Harness 1 pc 3 2Pin Power Wire Harness with Choke 1 pc 4 3 RCA Jack Pigtail 1 pc 5 Hardware Package 5 9 4 pcs TA4 9 6 pcs 6 Remote Control 1 pc 7 ounting Bracket 1 pc 8 Snap on Shroud 2 pcs 9 Snap on Screen Cover 2 pcs 10 Pry Tool 1 pc 11 3 5mm TIP 3RCA JACK PIG TAIL 1 pc 12 Trim Ring 3 pcs Note The AVXMTG10U is supplied with a black snap on shroud and screen cover To install the pewter or shale snap on shroud or screen cover the black snap on shroud and screen cover must be removed first See the following page for the removal process REMOVING AND INSTALLING SNAP ON COVERS Preparation Place the unit on a soft surface to avoid damaging the plastic Materials Required 1 2 3 4 Fr FR 10 Overhead LCD Monitor Shroud Screen Cover Pry Tool with DVD Player Disconnecting the Screen Cover 1 Open the LCD screen 2 Insert the supplied pry tool between the LCD scr
Download Pdf Manuals
Related Search