ATD Tools Atd-7333 Lawn Mower User Manual
Contents
1. Figure 2 Replacement Parts Illustration for Model Atd 7333 6 Replacement Parts List for model Atd 7333 7 G48900 0011 Return Spring Seal Kit Contents G59305 0007 NVINI NININ ea a a a Aap ay Sep OIIO INI gt oI Inw I0 0ol o SNSIOJ OIPIw wm I co tem Description Notes Atd Tools Inc 160 Enterprise Drive Wentzville MO 63385 Tel 636 327 9050 Fax 636 327 9046 www atdtools com2. Atd Tools Inc will repair or replace at its option without charge any of its products which fails due to a defect in material or workmanship or which fails to conform to any implied warranty not excluded hereby Performance of any obligation under this warranty may be obtained by returning the warranted product freight prepaid to Atd Tools Inc Warranty Service Department 160 Enterprise Drive Wentzville MO 63385 Except where such limitations and exclusions are specifically prohibited by applicable law 1 the CONSUMER S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE and 2 Atd Tools Inc SHALL NOT BE LIABLE FORANY CONSEQUENTIAL OR INCIDEN TAL DAMAGE OR LOSS WHATSOEVER and 3 THE DURATION OF ANY AND ALL EXPRESSED AND IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO A PERIOD OF ONE 1 YEAR FROM DATE OF PURCHASE Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Replacement Parts Illustration for model Atd 7333
3. turn If the load fails to lower a Use another jack to raise the vehicle high enough to reinstall jack stands b Remove the malfunctioning jack and then the jack stands c Use the functioning jack to lower the vehicle 4 After removing jack from under the vehicle fully lower the saddle to reduce ram exposure to rust and contamination Oil Filler Plug Handle on reservoir release valve Lifting Arm Handle Fork Figure 1 Typical Service Jack Nomenclature 3 Study understand and follow all printed materials provided with on this product before use Do not exceed rated capacity Use only on hard level surface This is a lifting device only Immediately after lifting support the load with a pair of appropriately rated jack stands Lift only on areas of the vehicle as specified by the vehicle manufacturer Do not move or dolly the vehicle while on the jack No alterations shall be made to this product FAILURE TO HEED THESE MARKINGS MAY RESULT IN PERSONAL INJURY AND OR PROPERTY DAMAGE To avoid crushing and related injuries Never work on under or around a load supported only by hydraulic jack e Always use adequately rated jack stands e Chock each unlifted tire in both directions Do not use this device to lift level lower support nor move a house mobile home travel trailer camper or any building structure Be alert and sober when using this product Do
4. ERATION Lifting Only attachments and or adapters supplied by the manufacturer shall be used Lift only on area ofthe vehicle as specified by the vehicle manufacturer Follow the vehicle manufacturer s recommended guidelines for lifting Engage the emergency brake and chock each unlifted wheel in both directions to prevent inadvertent vehicle movement 2 Close the release valve by turning the handle clockwise until firm resistance is felt 3 Refer to the vehicle manufacturer owner s manual to locate approved lifting points on the vehicle Center jack saddle under lift point 4 Verify lift point then pump handle to contact lift point To lift pump handle until load reaches desired height 5 Transfer the load immediately to appropriately rated jack stands NEVER use hydraulic jack as a stand alone device ALWAYS transfer the lifted load IMMEDIATELY to a pair of appropriately rated jack stands Use one pair of jack stands per vehicle Rated capacity is per pair only Do not exceed rated capacity Lowering Be sure all tools and personnel are clear before lowering load Slowly open the release valve The more you turn the handle counter clockwise the faster the load will come down Maintain control of the rate of speed at which the load lowers at all times 1 Raise load high enough to clear the jack stands 2 Remove jack stands carefully always used in pairs 3 Slowly turn the handle counter clockwise but no more than 1 2 full
5. Hydraulic Service Jack Operating Instructions amp Parts Manual Model Number Capacity Atd 7333 2 1 2 Ton dE TETE di This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death To avoid crushing and related injuries e Leer comprender y seguir las instrucci nes antes NEVER work on under or around a load supported only by a hydraulic de utilizar el aparato e El manual de instrucci nes y la informaci n de A jack ALWAYS use adequately rated seguridad deben estar comunicado en lengua del jack stands operador antes del uso e No seguir estas indicaci nes puede causar da os personales o materiales Atd Tools Inc 160 Enterprise Drive Wentzville MO 63385 OIPM 7333 0310 Printed in China SAFETY and GENERAL INFORMATION Save these instructions For your safety read understand and follow the information provided with and on this jack before using The owner and operator of this equipment shall have an understanding of this jack and safe operating procedures before attempting to use The owner and operator shall be aware that use and repair of this product may require special skills and knowledge Instructions and safety information shall be conveyed in the operator s native language before use of this jack is authorized If any doubt exists as to the safe and proper use of
6. ith the product its components and recognize the hazards associated with its use 3 To familiarize yourself with basic operation locate and turn the release valve handle a Clockwise until firm resistance is felt to further turning This is the CLOSED release valve position used to raise the saddle b Counter clockwise but no more than 1 2 turn from the closed position This is the OPEN release valve position used to lower the saddle 4 With saddle fully lowered remove the oil filler plug Pump 6 to 8 full strokes This will help release any pressurized air which may be trapped within the reservoir Check oil level Proper oil level will vary from just covering the ram cylinder to 3 16 above it as seen from the oil filler hole Reinstall the oil filler plug 5 Ensure that jack rolls freely Raise and lower the unloaded saddle throughout the lifting range before putting into service to ensure the pump operates smoothly Replace worn or damaged parts and assemblies with ATD Tools authorized replacement parts only Bleeding Venting Trapped Air With the release valve in the OPEN position 3b and with saddle fully lowered locate and remove the oil filler plug Pump 6 to 8 full strokes This will help release any pressurized air which may be trapped within the reservoir Reinstall the oil filler plug SPECIFICATIONS Saddle Capacity Jack Size Lx W x H Fe a Atd 7333 2 1 2 Ton 25 3 8 x 13 1 8 x 6 1 2 Er ETS 1 2 OP
7. not operate under the influence of drugs or alcohol MAINTENANCE Important Use only good grade hydraulic jack oil Avoid mixing different types of fluid and NEVER use brake fluid turbine oil transmission fluid motor oil or glycerin Improper fluid can cause premature failure of the jack and the potential for sudden and immediate loss of load We recommend Mobil DTE 13M or equivalent Adding oil 1 With saddle fully lowered set jack in its upright level position Remove oil filler plug 2 Fill with oil until 3 16 above the inner cylinder as seen from the oil filler hole Reinstall the oil filler plug Changing oil For best performance and longest life replace the complete fluid supply at least once per year 1 With saddle fully lowered remove the oil filler plug 2 Lay the jack on its side and drain the fluid into a suitable container Note Dispose of hydraulic fluid in accordance with local regulations 3 Fill with oil until 3 16 above the inner cylinder as seen from the oil filler hole Reinstall oil filler plug Lubrication A periodic coating of light lubricating oil to pivot points axles and hinges will help to prevent rust and assure that wheels casters and pump assemblies move freely Cleaning Periodically check the pump piston and ram for signs of rust or corrosion Clean as needed and wipe with an oily cloth Note Never use sandpaper or abrasive material on these surfaces Storage When not in use store
8. the jack with saddle fully lowered a Symptom PossibleCauses Causes Corrective Action Action Jack will not lift load e Release valve not tightly closed e Ensure release valve tightly closed e Load is too heavy e Consider higher capacity jack Jack will lift but not maintain e Release valve not tightly closed e Ensure release valve tightly closed pressure e Hydraulic unit malfunction e Discontinue use contact ATD Tools technical service Jack will not lower after unloading Reservoir overfilled e Drain fluid to proper level e Linkages binding e Clean and lubricate moving parts e Fluid level low e Ensure proper fluid level Poor lift performance Fluid level low e Ensure proper fluid level e Air trapped in system e With ram fully retracted remove oil filler plug screw to let pressurized air escape Reinstall oil filler plug Will not lift to full extension Fluid level low e Ensure proper fluid level REPLACEMENT PARTS Available Parts Please refer to the Parts drawing when ordering parts Not all components of this kit are replace ment items but are illustrated as a convenient reference of location and position in the assembly sequence When ordering parts give Model number serial number and description below Call or write for current pricing Atd Tools Inc 160 Enterprise Drive Wentzville MO 63385 Tel 636 327 9050 Fax 636 327 9046 ONE YEAR LIMITED WARRANTY For a period of one 1 year from date of purchase
9. this jack remove from service immediately Inspect before each use Do not use if broken bent cracked or damaged parts are noted Any jack that appears damaged in any way or operates abnormally shall be removed from service immediately If the jack has been or suspected to have been subjected to a shock load a load dropped suddenly unexpectedly upon it immediately discontinue use until jack has been checked by a factory authorized service center contact distributor or manufacturer for list of authorized service centers It is recommended that an annual inspection be done by qualified personnel Labels and Operator s Manuals are available from manufacturer PRODUCT DESCRIPTION Hydraulic Service Jack is designed to lift but not support one end of a vehicle Immediately after lifting loads must be supported by a pair of appropriately rated jack stands NEVER use hydraulic jack as stand alone device After lifting immediately support the lifted vehicle with a pair of appropriately rated jack stands PREPARATION Assembly 1 Assemble the 2 piece handle with provided bolt 2 Insert handle into the handle fork Tighten the bolt on handle fork to prevent accidental removal of handle while in use Before Use 1 Verify that the product and application are compatible if in doubt call ATD Tools Technical Service line 636 327 9050 2 Before using this product read the operator s manual completely and familiarize yourself thoroughly w
Download Pdf Manuals
Related Search