Asus CRW-2410S Network Card User Manual
Contents
1. 24105 24x 10x 40x CD RW Drive User s Manual Copyrights Disclaimer Copyright 2001 ASUSTeK COMPUTER INC All Rights Reserved No part of this manual including the products and software described in it may be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form or by any means except documentation kept by the purchaser for backup purposes without the express written permission of ASUSTeK COMPUTER INC 505 ASUS PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN NO EVENT SHALL ASUS ITS DIRECTORS OFFICERS EMPLOYEES OR AGENTS LIABLE FOR ANY INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING DAMAGES FOR LOSS OF PROFITS LOSS OF BUSINESS LOSS OF USE OR DATA INTERRUPTION OF BUSINESS AND THE LIKE EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT Product warranty or service will not be extended if 1 the product is repaired modified or altered unless such repair modification of alteration is authorized in writing by ASUS or 2 the serial number of the product is defaced or missing The product name and revision number are both printed on the product itself Ma2. 24 FCC CDC Statements Federal Communications Commission Statement This device complies with FCC Rules Part 15 Operation is subject to the following two conditions e This device may not cause harmful interference and e This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with manufacturer s instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment to an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help WARNING The use of shielded
3. 9 Product Introduction 9 5 9 10 115 418 Panel 12 Rear Panel 13 5 14 System Requirement 14 Setting the Jumper Terminals 15 Installing the CD RW Drive 16 Connecting the Drive Cables 18 Installing the Device 19 Installing the CD RW Software 19 CD RW Drive Basics 20 Placing a Disc into the Drive 20 Ejecting a Disc from the Drive 21 Using the Emergency Eject Pinhole 22 Using Compact 5 5 5 23 Cleaning a DISC cetera 6 23 0 8 56 23 Technical Information 24 Environmental 24 Electrical Characteristics
4. Using the Emergency Eject Pinhole The emergency eject pinhole on the front of the drive allows you to manually eject the drive tray and remove a disc from the drive in the following instances supply of power to the computer is cut due to electrical power outage the drive malfunctions Follow these steps to eject the drive tray using the emergency pinhole 1 Insert a pointed rod such as a pin a needle or paper clip small enough to fit into the emergency pinhole 2 Carefully pull the tray out and remove the CD 22 ASUS CRW 2410S User s Manual Using Compact Discs Take note of the instructions in this section when using compact discs These instructions will help you avoid damaging the discs and your CD RW drive Cleaning a Disc Spray the disc with compressed air for about five seconds to get rid of the dust on a disc Handling a Disc Hold a disc by the edges Do not touch the disc surface ASUS CRW 2410S User s Manual 23 Technical Information Environmental Specifications Temperature Operation 5 C lt to lt 45 C Storage 30 C to lt 60 C Humidity Operation 20 to 80 non condensing Storage 90 40 C 48 h Mean Time Between Failure 30000 POH DUTY 20 read operation MTBF Life Tray Loading 20000 cycles Traverse mechanism 1000000 seek Vibration Operation Read 0 98 m s 0 1 G 10 to 500 Hz Random vibration Non operation transport 800 13
5. 3 Hz 3 mm 1 06 Up Down 20 min Impact Drop impact 490 m s 50 G 3 directions 6 ms POH Power On Hour live current time DUTY Actual operation time Electrical Characteristics Power Consumption DC 5V 2 0A peak DC 12V 2 0A peak I O Terminal Power connector 4 pin 5V 12V ATAPI terminal 40 pin Audio out 4 pin analog 2 pin digital Audio Sampling 44 1 kHz T H D Line out 0 15 at 1 kHz Headphone 0 2 at 1 kHz Vol imW Vol Max Channel separation 70 dB 28 dB S N ratio 70 db 65 dB Output 0 7V typical 0 9V typical ASUS CRW 2410S User s Manual
6. cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications This class B digital apparatus complies with Canadian ICES 003 ASUS Contact Information ASUSTeK COMPUTER INC Asia Pacific Marketing Address 150 Li Te Road Peitou Taipei Taiwan 112 Telephone 886 2 2894 3447 Fax 886 2 2894 3449 Email info asus com tw Technical Support Tel English 886 2 2890 7123 Tel Chinese 886 2 2890 7113 Fax 886 2 2893 7775 Email tsd asus com tw Newsgroup news2 asus com tw WWW www asus com tw FTP ftp asus com tw pub ASUS ASUS COMPUTER INTERNATIONAL America Marketing Address 6737 Mowry Avenue Mowry Business Center Building 2 Newark CA 94560 USA Fax 1 510 608 4555 Email info usa asus com tw Technical Support Fax 1 510 608 4555 BBS 1 510 739 3774 Email tsd asus com WWW www asus com FTP ftp asus com pub ASUS ASUS COMPUTER GmbH Europe Marketing Address Harkortstr 25 40880 Ratingen BRD Germany Fax 49 2102 442066 Email sales asuscom de for marketi
7. device 5 IDE connector This connector is for a 40 pin IDE cable to connect the drive to the IDE interface on the motherboard 6 Power connector This DC connector is for a 4 pin power cable from the system power supply ASUS CRW 2410S User s Manual 13 Installation System Requirements Before installing and using the CD RW drive make sure that your computer system meets the following requirements 14 IBM compatible Pentium 166MHz or higher MS Windows 95 98 98SE ME 2000 NT4 0 operating system At least 64MB system memory 128MB is recommended An empty 5 25 inch external drive bay HDD empty storage capacity of 100MB or more Average seek time 20ms or less Transmission rate 2 MB s or more NOTE Do not use a hard disk that calibrates thermally during operation Recommended media CD R x2 x24 TAIYOYUDEN MITSUMI CHEMICAL MITSUBISHI CHEMICAL RICOH RITEK PRINCO CD R x2 x16 TDK HITACHI MAXELL FUJI FILM PIONEER VIDEO KODAK CD RW x2 x10 MITSUBISHI CHEMICAL RICOH ASUS CRW 2410S User s Manual Setting the Jumper Terminals Configure the the jumpers to set the device to master or slave mode before physically installing it to your computer chassis Use jumper blocks to short the pins to your desired setting CAUTION Make sure to correctly place the jumper blocks over the pins Failure to do so may cause irreparable damage to the drive Jumper Terminals Master Mode Cover the tw
8. the device is in reading or writing mode Do not place damaged discs inside the device Do not place discs into the device immediately if they came from a cold environment specially during cold seasons Wait until the discs have reached room temperature Package Contents Upon opening your ASUS CRW 2410S drive package check if all the following items are present and in good condition If any of the items is damaged or missing contact your retailer immediately ASUS CRW 2410S drive IDE cable Drive screws Nero 5 Burning ROM disc ASUS 24X CD R disc ASUS 10X CD RW disc User s Manual Welcome Thank you for buying the ASUS CRW 2410S Drive To ensure proper installation and use of this device read the instructions and other important information contained in this manual Product Introduction Specifications The CRW 2410S has the following specifications Speeds Interrface Technology support Buffer size Application discs Recording form OS compatibility Power supply Dimensions Mass 24X writes 10X rewrites 40X reads ATAPI specification BURN Proof technology Zone CLV Recording technology FlexSS BP Speed Control technology 2MB 12cm or 8cm diameter 1 2mm thick CD ROM Video CD CD DA Photo CD CD I CD G CD TEXT CD Extra Orange Book Part 2 3 Disc at once Track at Once Fixed packet Variable packet MS Windows 95 98 98SE ME 2000 NT4 0 DC 5 x 1 10 V DC 12 x 1 10
9. V 148 0 w x 192 4 d x 42 3 h mm 950 g NOTE Refer to the section Technical Information on page 24 for detailed specifications ASUS CRW 2410S User s Manual Features The ASUS CRW 2410S is a CD RW drive with 24X write 10X rewrite and 40X read capabilities The drive complies with the AT Attachment Packet Interface ATAPI specification and comes equipped with a host of the latest innovative technologies in CD recording BURN Proof Technology The BURN Proof technology which stands for Buffer Under RuN Proof prevents the buffer underrun error caused by an empty data buffer It does so by means of a controller that continuously monitors the status of the data buffer throughout the write process If the available data drops below 10 of the total buffer capacity the controller initiates a controlled interrupt to the writing process and sets a write marker New data is then loaded to the cache and the laser is repositioned The drive synchronizes the data already written with the new data in the buffer and repositions the laser behind the sector most recently written This technology also ensures that your PC remains fully operational throughout the writing process and available for other applications Zone CLV Recording Technology The Zone Constant Linear Velocity CLV recording method allows you to achieve a higher recording speed by using a different speed for each of the three zones partitioned from the i
10. chassis For cable connections proceed to the following section Connecting the Drive Cables ASUS CRW 2410S User s Manual 17 Connecting the Drive Cables 1 Connect the power cable plug to the power connector on the rear panel 2 Connect the 40 pin IDE cable plug to the IDE connector matching the red pin stripe on the cable with Pin 1 on the connector If your computer has a sound card or an onboard audio feature connect an audio interface cable to the 4 pin analog audio connector on the rear of the drive Connect the other end of the audio cable to the connector on the sound card or on the 4 pin CD connector on the motherboard CAUTION the cable plugs are slotted so that they fit in only one orientation If a plug does not fit in completely try reversing it DO NOT use too much force when fitting the cable plugs My 11111 din 1111 1 11 Audio Cable IDE Cable Power Cable NOTE Replace the computer cover according to your computer manual 18 ASUS CRW 2410S User s Manual Installing the Device Driver Before you can use your CDR 2410S drive you must first install the device driver IMPORTANT Make sure you that you have completed the drive installation and have replaced the computer cover before you proceed Follow these steps to install the device driver 1 Turn on the computer 2 Your operating system OS detects the new hardware CD RW drive that you install
11. ed and automatically looks for the appropriate driver 3 Follow the screen instructions to install the driver Installing the CD RW Software The ASUS CRW 2410S drive supports the following software applications By AHEAD software gmbh e Nero Burning ROM e InCD Wave Editor Cover Designer By Microsoft Corporation e Media Player CD Player e Active Movie By Kodak Kodak Photo CD Player V2 0 or higher NOTE Refer to the manuals that came with the specific software for installation instructions ASUS CRW 2410S User s Manual 19 CD RW Drive Basics Placing a Disc into the Drive 1 Press the eject button on the front of the drive to eject the tray 2 Place the disc on the drive tray with the label printed side up NOTE f you are using a 12cm disc place it on the tray making sure that it fits the outer circular border This border helps hold the disc in place If you are using an 8 disc place it on the inner circular border on the tray 3 Press the drive eject button or lightly push the center of the drive tray to replace the tray inside the drive 20 ASUS CRW 2410S User s Manual Ejecting a Disc from the Drive 1 Press the eject button on the front of the drive to eject the tray 2 Carefully remove the disc from the tray 3 Press the drive eject button or lightly push the center of the drive tray to load the tray back into the drive ASUS CRW 2410S User s Manual 21
12. ng requests only Technical Support Hotline MB Others 49 2102 9599 0 Notebook 49 2102 9599 10 Fax 49 2102 9599 11 Support Email www asuscom de de support for online support WWW www asuscom de FIP ftp asuscom de pub ASUSCOM Safet y Information Observe the following precautions before installing and using the ASUS CRW 2410S Drive Installation Notices Do not place this device in an unstable position or in one that vibrates Do not place this device in areas where there is direct sunlight high humidity or damp condition Do not use or place this device near magnetic fields televisions or radios where there is interference that may affect the performance of the drive Do not attempt to disassemble or repair the drive Opening the drive may result to exposure to laser radiation Safet Information Using the Device Do not move the device from a cold to a warm or hot environment Drastic change of temperature is harmful to the device Before moving or uninstalling the drive remove a disc from it if any Prevent liquids or any metal to get into the device If this situation occurs contact your retailer for help Do not use any evaporating solvents to clean the device If you accidentally sprayed any solvent on the device use a clean cloth to wipe it You may also use a neutral cleaner to dilute the solvent to easily wipe it from the device Try not to interrupt the supply of power while
13. nner to the outer area in a disc When using the Zone the recording in Zone 1 is 16x speed then increases to 20x speed in Zone 2 after t1 time In Zone 3 the recording reaches 24x speed after t2 time When the recording is complete the drive accesses and checks the recorded data area to execute synchronization between Zones 1 and 2 then between Zones 2 and 3 The BURN Proof technology is used to execute this synchronization preventing any gap between the zones The illustration on the next page shows the Zone CLV process ASUS CRW 2410S User s Manual Zone CLV Recording Method Velocity 24 20 20 FlexSS BP Speed Control Technology The FlexSS BP technology stands for Flexible Speed and Flexible Strategy This technology prevents problems with recording media when writing at high speeds like 20x or 24x Because of disc variations caused by serpentine tracks or off centered discs Flexible Speed allows the drive to assess the physical condition of the disc then determine the suitable recording speed for the disc While recording the drive continues to monitor the disc condition and flexibly switches to different speeds to maintain the optimum recording condition Flexible Strategy measures and evaluates the recording condition of recorded area at switching zones This feature can restart the recording after checking the pit condition at the recording stop
14. nual revisions are released for each product design represented by the digit before and after the period of the manual revision number Manual updates are represented by the third digit in the manual revision number SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies and are used only for identification or explanation and to the owners benefit without intent to infringe Product Name CRW 2410S Manual Revision 1 00 E806 Release Date July 2001 Contents Copyrights Disclaimef 2 5 4 ASUS Contact Information 5 Safety Information 6 Installation 6 USING the Devices a 7 8 Welcome liiati aasian
15. o pins below the label MA to set the CD RW drive as a Secondary Master drive This is possible only if your computer supports four IDE devices The hard disk in the computer is set as Primary Master Slave Mode Cover the two pins below the label SL to set the CD RW drive as a Slave device if your computer supports only two IDE devices lf your computer supports four IDE devices this setting sets your CD RW drive as a Primary Slave or Secondary Slave Cable Select Mode Cover the two pins below the label CS if your computer supports a Cable Select CSEL signal You need an exclusive interface cable for this setting Refer to your computer manual for details ASUS CRW 2410S User s Manual 15 Installing the CD RW Drive Follow these steps to install the drive into the computer chassis NOTE Refer to your computer manual for specific instructions on opening the chassis and installing drives 1 Remove the cover of an empty 5 25 inch external drive bay 2 Carefully insert the CD RW drive into the bay and push it inward until it is flushed to the chassis front panel The holes on the sides of the drive should align with the holes on the drive bay 16 ASUS CRW 2410S User s Manual 3 Secure the drive with screws that came with the drive package Use two screws on each side of the drive IMPORTANT Depending on the space on your chassis you may need to connect the drive cables before securing the drive into the
16. position and the optimization of the recording parameters ASUS CRW 2410S User s Manual 11 12 Front Panel BURN Proof 24x 70x40x Emergency eject pinhole In cases when you cannot eject a disc from the drive using the eject button due to power failure or software problems insert a pin into this hole to mechanically eject the tray and the disc Headphone jack This jack allows you to connect a headphone with a stereo mini plug Headphone volume dial This volume dial allows you to control the volume of the headphone connected to the drive Turning the dial to the left decreases the volume turning to the right increases volume BUSY indicator This LED indicates three types of conditions OFF Paused or stopped ON Reading and accessing a disc BLINKING TOC reading ejecting a disc WRITE indicator This LED turns ON while data is being written on the disc Disc tray This tray holds the disc Eject button This button allows you to eject the disc tray to place a disc or remove a disc ASUS CRW 2410S User s Manual Rear Panel 1 Digital audio connector This connector is for a digital signal output cable 2 Analog audio connector This connector is for an analog signal output cable 3 Factory test pins These pins are used for factory testing NOTE DO NOT cover these pins with jumper blocks 4 CS SL MA pins These pins are used to set the drive to either a master or slave
Download Pdf Manuals
Related Search