APC WMR1000GI Network Router User Manual
Contents
1. username and password Enter Admin for the username and APC for the password The Mode Configuration screen appears 7 Click the Configure button for AP mode The AP Setup screen Figure 6 appears Wireless Security Security System Bs Authentication Auto v Key Size 64 Bit 10Hexchars Key 1 Key 2 O Key 3 O Key 4 O Generate Passphrase Figure 6 AP Setup Screen 8 Enter all relevant data Refer to the APC 3 in 1 Wireless Mobile Router User s Manual on the documentation CD for more information Step 3b AP Router Mode Setup Note By default the APC 3 in 1 Wireless Mobile Router allows both 802 11g and 802 11b connections AP ROUTER MODE Shared IP address LAN WAN ay i DHCP k Server Teua 1 1 Ce ee re eee ee ear aa ee tee ae ee er ee ee eo ee Figure 7 AP Router Mode Configuration To configure the Wireless Mobile Router for AP Router mode proceed as follows 1 Use the mode selector switch on the side of the router to select Config mode switch position 3 2 Power up the router and wait for the Ethernet LED to come on indicating that the router is ready 3 Make sure that a connection is established between the computer and the router a wired connection is recommended 4 Start the Web browser In the Location or Address bar enter http and the current IP address for the wireless LAN as set on the AP Router screen The default value i2. C 3 in 1 Wireless Mobile Router e For wireless LAN connections each computer must have a wireless network adapter installed e Internet access from your Internet Service Provider ISP using a Digital Subscriber Line xDSL cable modem or Large Area Network LAN with Dynamic Host Configuration Protocol DHCP service protocol for automating the configuration of computers that use TCP IP e TCP IP network protocol installed on each computer in order to configure the Router or to access the Internet Modes The APC 3 in 1 Wireless Mobile Router functions in the following modes see the back panel for switch settings e Access Point AP mode switch position 1 to act as a wireless bridge between an existing LAN and a wireless user It inherits the profile security user etc of the existing LAN e AP Router mode switch position 2 to act as a wireless networking device that connects networks by a wireless connection and create specific profiles such as security and users e Config Configuration mode switch position 3 to connect to the APC 3 in 1 Wireless Mobile Router to change its configuration e Client mode switch position 4 to convert an Ethernet port to a wireless interface Security Alert When in a location such as a hotel or airport that requires payment to connect to the Internet APC recommends using AP Router mode switch position 2 with security set to WEP WPA or MAC filtering These settings
3. as set on the System screen a prompt appears for the username and password Enter Admin for the username and APC for the password The Mode Configuration screen appears Click the Configure button for Client mode The Client Mode Setup screen Figure 10 appears Legendary Reliability Client Mode Setup Wireless Profiles Name SSID Type Security Default Infrastructure Disabled indicates current profile Figure 10 Client Mode Setup Screen Enter all relevant data Refer to the APC 3 in 1 Wireless Mobile Router Users Manual on the documentation CD for more information Once setup is complete use the mode selector switch to select Client mode switch position 4 Restart your computer or the device with which you are using the APC 3 in 1 Wireless Mobile Router in Client mode Troubleshooting Before contacting Technical Support please refer to the APC 3 in 1 Wireless Mobile Router User s Manual on the documentation CD and to the technical information available at www apc com Warranty The standard warranty is two 2 years from the date of purchase APC s standard procedure is to replace the original unit with a factory reconditioned unit APC will ship the replacement unit after the repair department receives the defective unit or cross ship upon the receipt of a valid credit card number The customer pays for shipping the unit to APC APC pays ground freight transportation costs to ship the
4. help to avoid any unauthorized access and charges For more information on security and mode selection see the user s manual Installation The Wireless Mobile Router can be powered using a USB cable Step 1a or by A C power Step 1b Caution Connect the APC 3 in 1 Wireless Mobile Router only to the USB port of the APC TravelPower Adapter Do not connect the APC 3 in 1 Wireless Mobile Router to the USB port of any other device Failure to comply may result in damage to the device Step 1a Connect Power USB Power the Wireless Mobile Router using the USB cable provided as follows 1 Connect one end of the USB cable to the APC TravellPower Adapter 2 Connect the other end of the USB cable to the Wireless Mobile Router Figure 3 Wireless Mobile Router Connected to APC s TravelPower Adapter Using a USB Cable Step 1b Connect Power Power Adapter Power the APC 3 in 1 Wireless Mobile Router using the 100 120 230 volt power adapter provided with the router Figure 4 as follows 1 Connect one end of the adapter power cord to the APC 3 in 1 Wireless Mobile Router 2 Connect the transformer block to a 100 230 volt power source Figure 4 Wireless Mobile Router Adapters for parts of the world not including North America Step 2 Network Connection Connect a DSL or cable modem on an existing network to the Ethernet port of the APC 3 in 1 Wireless Mobile Router Step 3 Mode Setup The fol
5. lowing steps describe how to perform e Access Point AP Mode Setup e AP Router Mode Setup e Client Mode Setup Note Use Config mode to perform all configurations Make sure that the mode selector Switch on the side of the router is set properly Note APC recommends using WEP security at a minimum to protect against unauthorized access to the router For information on setting up WEP security refer to the APC 3 in 1 Wireless Mobile Router Users Manual on the documentation CD Step 3a Access Point AP Mode Setup Note By default the APC 3 in 1 Wireless Mobile Router allows both 802 11lg and 802 11b connections Figure 5 AP Mode Configuration To configure the APC 3 in 1 Wireless Mobile Router for AP mode proceed as follows 1 Use the mode selector switch on the side of the router to select Config mode switch position 3 2 Power up the router and wait for the Ethernet LED to come on indicating that the router is ready 3 Establish a wired or wireless connection to the router Wired is recommended whenever possible For wired connect a standard LAN cable from the computer s 10 100BaseT Ethernet port to the Ethernet port on the router For wireless select the wireless network with the SSID APC_AP 4 Start the Web browser 5 Inthe Location or Address bar enter contig ap Note This will work only in Config mode 6 If the admin password was set on the System screen a prompt appears for the
6. n name forwarding for domain name mapping e Stateful Packet Inspection SPI firewall with client privileges hacker prevention and Network Address Translation NAT NAT also enables multi user access with a single user account and virtual server functionality providing protected access to Internet services such as Web File Transfer Protocol FTP electronic mail and Telnet e Virtual Private Network VPN support using PPTP L2TP or IPSec pass through e Easy setup through a Web browser on any operating system that supports Transmission Control Protocol Internet Protocol TCP IP e Compatible with all popular Internet applications e Can be powered using a USB cable or power adapter e Integrates with APC s TravelPower Case Figure 2 and is compatible with APC s TravelPower Adapter Note The TravelPower Case is sold separately and may or may not include the TravelPower Adapter depending on the model purchased For more information go to www apc com Wireless Mobile TravelPower TravelPower Adapter Router Case Figure 2 Wireless Mobile Router Connector to APC s TravelPower Adapter System Requirements To use the Wireless Mobile Router required system elements are as follows A computer that runs a Microsoft Windows based Operating System OS or Apple Mac OS e A Web browser such as Microsoft Internet Explorer 5 0 or above installed on one computer at the site for configuring the AP
7. replacement unit to the customer Warranty Registration To register this product for purposes of the warranty please go to warranty apc com APC Contact Information Technical Support www apc com support Internet www apc com USA and Canada 866 WIFI APC France 0800 906 483 Asia Pacific China Europe Middle East Africa Worldwide 65 3896 823 86 10 8529 9888 353 91 702020 1 401 789 5735 990 2145 Copyright 2005 American Power Conversion All rights reserved APC is a registered trademark of American Power Conversion All other trademarks are the property of their respective owners
8. s 192 168 1 1 For example BETDA 192 1600 1 1 If the admin password was set on the System screen a prompt appears for the username and password Enter Admin for the username and APC for the password The Mode Configuration screen appears Click the Configure button for AP Router mode The AP Router Mode Setup screen Figure 8 appears Wireless Security Security System AMHA ay v PSK Key Lifetime 3600 secs Encryption TKIP Figure 8 AP Router Setup Screen Enter all relevant data Refer to the APC 3 in 1 Wireless Mobile Router Users Manual on the documentation CD for more information Step 3c Client Mode Setup CLIENT MODE Figure 9 Client Mode Configuration To configure the APC 3 in 1 Wireless Mobile Router for Client mode proceed as follows l 2 Use the mode selector switch on the side of the router to select Config mode switch position 3 Power up the router and wait for the Ethernet LED to come on indicating that the router is ready 10 Establish a wired or wireless connection to the router Wired is recommended whenever possible For wired connect a standard LAN cable from the computer s 10 100BaseT Ethernet port to the Ethernet port on the Wireless Mobile Router For wireless select the wireless network with the SSID APC_AP Start the Web browser In the Location or Address bar enter config ap Note This works only in Config mode If the admin password w
9. www apc com APC 3 in 1 Wireless Mobile Router Quick Installation Guide Model NumberWMR1000GI Part Number 990 2145 Warning Be careful when using the APC 3 in 1 Wireless Mobile Router for an extended period of time as the unit can become hot Introduction Thank you for purchasing the APC 3 in 1 Wireless Mobile Router Figure 1 This device provides connectivity up to 54 Mbps It is designed for wireless mobile users needing Internet sharing and networking in mobile and home small office applications Power Power LED Wireless LED Ethernet LED Figure 1 APC 3 in 1 Wireless Mobile Router Note The purchaser must use the APC 3 in 1 Wireless Mobile Router in full compliance with local laws and ordinances and guidelines established by the local service provider Package Contents e APC 3 in 1 Wireless Mobile Router e 5 Volt 2 Amp AC DC Power Adapter e Category 6 CAT6 Ethernet Cable e Quick Installation Guide e Documentation CD e Universal Serial Bus USB Power Cable Please contact the reseller if any of the listed items are missing from the packaging Features and Benefits e Internet connection to DSL or cable modem via a 10 100 Mbps Ethernet port e IEEE 802 11lg and IEEE 802 11b compliant interoperable with multiple vendors equipment e Provides roaming within 802 11b WAN LAN environment e Dynamic Host Configuration Protocol DHCP for dynamic Internet Protocol IP configuration and domai
Download Pdf Manuals
Related Search