American Standard 6058.102 Outdoor Kitchen Island User Manual
Contents
1. Remove ENCLOSURE COVER 2 Close SUPPLY STOPS Note Keep water flowing out of faucet while shutting off 4 Unthread STRAINER 1 using a 7 16 socket CLEAN SCREENS 5 Pull out the STRAINER 1 and clean with an old toothbrush Rinse thoroughly with water 6 Install the STRAINER 1 back in its place and tighten with a 7 16 socket Caution do not over tighten strainer Note It is recommended to clean strainer every 6 months 7 Replace ENCLOSURE COVER Tighten cover screws firmly a r 4 4 a 45 e 7 i al lt oe E HOW TO CLEAN AND REMOVE THE AERATOR Fig 3 1 Remove AERATOR HOUSING 1 with KEY 2 supplied with faucet 3 Remove AERATOR 3 from HOUSING 1 Fig 3a 2 Clean the AERATOR SCREENS 4 with a old tooth brush to remove dirt 4 Rinse Clean with water Reassemble and install into spout end Be sure the black seal washer is in place M968857 REV 1 2 H GENERAL CLEANING Fig 4 1 For general cleaning use a damp soft cloth to clean the spout and the sensor 2 For cleaning dirt use a soft cloth with diluted dish washing detergent Wipe the area using a wet cloth and dry using a soft cloth Do not scratch the sensor when cleaning Avoid using anything that may scratch the spout surface Never use polishing power detergent or a nylon scrub brush They will damage the surface of the spout or Sensor Q Why has the flow rate of the faucet reduced signifi2. 11 0070A MOUNTING KIT 605P800 DI 044912 0070A MOUNTING NUT A923672 0070A FAUCET SUPPLY HOSE I eg Tens A960221 0070A WIRE COVER M950169 0070A POWER SUPPLY KC M962387 0070A A913202 0070A MOUNTING WASHER SCREW KIT A951590 0070A MOTOR ASSEMBLY A963410 0070A CHECK VALVE A922251 0070A he A924162 0070A A923237 0070A SOLID GROMMET SUPPLY HOSE PLUG i b N gt CO A950489 0070A lt lt CIRCUIT BOARD POWER SUPPLY GROMMET KOL A922267 0070A ROUND GROMMET M962389 0070A SOLENOID amp SCREWS A918462 0070A SOLENOID SCREWS A950507 0070A FILTER A922290 0070A L A922272 0070A N U GROMMET Tia M961798 0070A m SEAL i a A960212 0070A 7 MIXING VALVE bN A961337 0070A SCREW A960211 0070A MOTOR ASSEMBLY For toll free information and answers to your questions call 1 800 442 1902 Weekdays 8 00 a m to 8 00 p m EST IN MEXICO 01 800 839 1 2 00 IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST Product names listed herein are trademarks of American Standard Inc American Standard Inc 2006 A963591 0070A GEAR I HOT LINE FOR HELP I 9 M968857 REV 1 2 Amoricam Standard M968857 REV 1 2
3. CERATRONIC PRODUCT NUMBERS Proximity Faucet with Touch Free 6058 105 Temperature Control 6058 102 Product No s amp Options 1 How to Install gt W Electrical Hook up LA gt ae ces p DEI Z Oe ov SS oe Operation 5 6 Certified to comply with ASME A112 18 1M Maintenance 6 8 2006 American Standard M968857 REV 1 2 FAQ s Replacement Parts Americam Standard NOTE TO INSTALLER Please give this manual to the customer after installation To learn more about American Standard Faucets visit our website at www us amstd com or U S customer s e mail us at faucetsupport Q amstd com Installation Instructions For Parts Service Warranty or other Assistance please call 1 800 442 1902 In Canada 1 800 387 0369 In Toronto Area only 1 905 3061093 M968857 REV 1 2 Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin All American Standard Faucets Are Water Tested At Our Factory U N PAC KING Some Residual Water May Remain In The Faucet During Shipping 1 Remove the fitting and loose items from the carton The illustration below shows the fitting and all loose items after they have been removed from the carton Some items may be packaged partially assembled to other items 1 Ceratronic Spout Assembly 5 4 Deck plate opti
4. OD VALVE 12 Red to Blue to Fig 1f 7 Connect SENSOR WIRE CONNECTIONS 13 to WIRE PLUGS 11 Red to Black to Fig 1g 8 Connect WHITE PLASTIC CONNECTOR 14 from the faucet to the MOTOR CONNECTOR 15 Fig 1h 9 Replace ENCLOSURE COVER 1 Tighten cover screws firmly Fig 1k M968857 REV 1 2 OPERATION Fig 1 fl HAND WASH SENSOR OPERATION Fig 1 When the Sensor detects a user the water immediately starts to flow Water flow will stop Two seconds after user is out of sensor range The off delay allows the user to comfortably move his hands without the flow cycling on to off As a precaution a safety timer will turn off the water after the sensor has been blocked for 59 seconds The water will stay off until the blockage is removed from the detection zone Output water temperature has a default setting See Section 3 for How to Set Default Temperature To change the output water temperature place one hand within the On Off Sensor range to activate faucet then place other hand within the Blue Sensor to decrease water temperature or the Red Sensor to increase water temperature Blue or Red LED will light up when hand is within the sensor range The Blue and Red sensor ranges cannot be adjusted DE Ego 2 10 50mm Note If On Off Sensor is not activated within 15 seconds of temperature adjustment then the faucet will adjust back to the default temperature settings Detectio
5. cantly A Check and clean aerator and strainer Q Why do I here humming noise from under the deck after faucet is turned off A The humming noise is the temperture control motor The faucet has a default termperature setting which is controlled by the motor which rotates a cycling cartridge If you have adjusted the temperature during faucet use then after 15 second delay the motor will rotate the cartridge back to the default temperature setting Q Why does the faucet operate the opposite of expected Turns On when not in sensor range but turns off when in sensor range A Sensor wires to solenoid are reversed Black to amp Red to Is correct Q What is the operating pressure range A Faucet will operate with supply pressures ranging from 20 80 psi Q There is no flow out of faucet when I m in sensor range A Open enclousure cover and verify that all electrical connections are tight specifically the Red amp Black sensor wire connectors to the wire plugs M968857 REV 1 2 CERATRONIC Ambrican Standard LAVATORY FAUCETS A960215 0070A Oo SENEO COVER PRODUCT NUMBERS A960217 0070A 6058 1 05 TEMPERATURE SENSOR KIT 6058 102 A960216 0070A PS SENSOR COVER RED Replace the YYY with appropriate finish code CHROME 002 M923827 YYYOA 2 2 GPM AERATOR 066508 YYYOA 0 5 GPM AERATOR A960218 0070A SCREW KIT 605P400 l A960219 0070A SENSOR KIT M9624
6. ect FLEXIBLE SUPPLIES 3 corresponing to the red dot on ENCLOSURE 2 to the hot water supply and the FLEXIBLE HOSE 3 corresponding to the blue dot to cold water supply Connection on FLEXIBLE SUPPLIES 3 are 3 8 compression Use adjustable wrench to tighten connection Do not over tighten FIG 4b Note FLEXIBLE SUPPLY 3 measures 20 from the bottom of the ENCLOSURE 2 base If additional supply length is required installer must purchase parts separately Important If FLEXIBLE SUPPLIES 3 are too long loop to avoid kinking ENCLOSURE MOUNTING HOLES ke 2 3 4 71mm MOUNTING HOLES FR Wy M968857 REV 1 2 ELECTRICAL INSTALLATION fl ELECTRICAL 1 Remove ENCLOSURE COVER 1 Fig 1 2 Remove CIRCUIT BOARD 2 from ENCLOSURE 3 May have to pull cord of power supply through Fig 1 3 Feed the WIRE CONNECTORS 4 through the top of ENCLOSURE 3 Fig 1b 4 Remove SPLIT PLUG 5 from GROMMET 6 Insert the gray SENSOR WIRE 7 and YELLOW and GREEN CONNECTOR WIRES 8 into SPLIT PLUG 5 Leave 4 of wire from end of SPLIT PLUG 5 Fig 1c Feed WIRES 7 amp 8 through GROMMET 6 Push SPLIT PLUG 5 into GROMMET 6 to seal Fig 1d 5 Reinstall CIRCUIT BOARD 2 into ENCLOSURE 3 with WIRES 7 amp 8 under CIRCUIT BOARD 2 Insert two WIRE CONNECTORS 9 into any of the three CIRCUIT BOARD RECEPTORS 10 Fig 1e 6 Connect WIRE PLUGS 11 to SOLENI
7. m shaded area shown in Fig 2 in order for electrical connections from the spout assembly to be made NOTE ENCLOSURE SUPPLY HOSE is 20 Distance between wall supply and ENCLOSURE 1 must be taken into consideration 2 Remove 4 screws from COVER 2 and pull off COVER 2 Hold the ENCLOSURE 1 in desired location and mark the four mounting hole locations as shown Fig 2 3 The ENCLOSURE 1 works best if secured to a wall stud or cross brace within the wall using the SCREWS 3 supplied If the ENCLOSURE 1 is to be installed on a tile or plaster wall the ANCHORS 4 and SCREWS 3 should be used 4 For installations on drywall or tiled walls use ANCHORS 4 and SCREWS 8 for securing ENCLOSURE 1 to finished wall Drill four 1 4 dia holes a minimum of 1 3 4 deep Insert the four ANCHORS 4 flush with face of the finished wall Align the ENCLOSURE 1 and Install the MOUNTING SCREWS 3 Tighten to secure ENCLOSURE 1 to mounting surface El CONNECT SPOUT HOSE TO ENCLOSURE Fig 3 1 Connect SUPPLY NUT 1 from spout assembly to nipple on top of ENCLOSURE 2 Tighten with adjustable wrench to make a water tight connection Fig 3 f CONNECT HOSES TO WALL SUPPLY Fig 4 1 Insert FIBER WASHERS 4 into SUPPLY NUTS 1 on ENCLOSURE 2 Fig 4 2 Connect SUPPLY NUT 1 on ENCLOSURE 2 to FLEXIBLE SUPPLY HOSE 3 Tighten to make a water tight connection Use two wrenches if necessary Fig 4a 3 Conn
8. n Zone 2 10 50mm 250mm Default Set at Factory 6 150mm A HOW TO CHANGE ON OFF SENSOR RANGE Factory set at 6 Fig 2a 2b 1 Setting the Detection Zone Distance Remove cover from ENCLOSURE Disconnect GRAY SENSOR WIRE 1 from circuit board then reconnect Fig 2 2 While the SENSOR CONTROL LED 2 is blinking slowly place your hand 1 2 in 80 50mm in front of the sensor Fig 2a 3 When the LED stops blinking and stays ON move your hand to the desired position and hold in place until the LED begins to blink again Fig 2b 4 Once the SENSOR CONTROL LED 2 begins to blink again remove your hand from the detection zone When the flashing stops the detection distance is set 5 Replace cover on ENCLOSURE M968857 REV 1 2 El HOW TO SET DEFAULT TEMPERATURE Fig 3 Note The factory setting of the Default Temperature is at a position of even amounts of hot and cold water flows This setting can only be changed within the first 15 minutes of switching on the power 1 Remove the power to the faucet by unplugging the Power Supply from the wall outlet Wait 60 seconds and then plug the Power Supply Back into the wall outlet 2 Place hand in front of Blue Cold Sensor until the Blue LED lights up Fig 3 3 Within the next 5 seconds start the faucet water flow by placing hand within the On Off Sensor range Fig 3 4 Adjust the output faucet temperature by using the Red Hot Sensor t
9. o increase or Blue Cold Sensor to decrease During this process always keep your hand within The On Off Sensor range in order to feel the change water temperature Fig 3 Fig 3a 5 Once desired temperature has been set remove hands away from the range of sensors Water flow will stop and both Red and Blue sensors will light up for 2 seconds indicating the default temperature has been set 6 The Default Temperature has been set This will remain the default setting untill the setting is changed again If power is lost this will remain the default setting Note The Default Setting is actually a mechanical positioning of a mixing valve Changes in the supply temperatures will create changes to the Default Temperature MAINTENANCE fl HOW TO REMOVE MIXING VALVE Fig 1 1 Remove four screws and pull off ENCLOUSURE COVER 1 Fig 1 2 Remove MOTOR GEAR COVER 2 by pulling off or pry off with a flat blade screw driver Fig 1a 3 Remove SCREW 3 from the center of the LARGE GEAR 4 and two SCREWS 5 from the MOTOR HOUSING 6 Fig 1a 4 Pull of MOTOR HOUSING 6 with LARGE GEAR 4 from the MIXING VALVE STEM 7 Fig 1b 5 Remove LOCKNUT 8 from the MIXING VALVE HOUSING 9 using adjustable wrench Fig 1c 6 Pull out MIXING VALVE 10 Use pliers if necessary Fig 1d 7 Reverse above steps for assembly M968857 REV 1 2 A HOW TO CLEAN FILTER Fig 2 CT NOONE Gisconnect AC power supply 1
10. onal must be ordered separately 2 Mounting Kit 6 8 Deck plate optional must be ordered separately 3 Electrical Enclosure 7 Optional Remote Control 4 Supply Hoses 8 Key for vandal resistant aerator T Ceratronic p ee No art Number Description oc 2 Lavatory Faucets P g og 6058 105 Ceratronic Proximity Faucets D a Q e Colored LED s signal temperature Jo 2 change mode Oe e Cast spout gon S e Vandal resistant oo oO e 0 5 gpm 1 9L min Spray 3 e Fully enclosed water resistant ca L AC Plug in Power supply included T e 3 8 SS compression flex hoses W 15 length a e Order deck plate and remote ai control separately optional 3 pa O Same as above e 2 2 gpm 8 3L min aerator Q v 23 wW o Zo e a ozmi U Q o z on amp 2015 j gt 7 D AK o 4 oe 0 UD t 8 ot D 20 2 ot i i ool 6 605P400 4 Deck plate cast brass 2 hle e 1 4 fixation bolts at 4 centers 35 S Spin nuts g B D g hu Q 605P800 8 Deck plate v e Cast brass D e 1 4 fixation bolts at 8 centers 2 Spin nuts 605XRCN Optional Remote Control D e Change functions or adjust 2 3 setup parameters Q Q e Battery Powered 2 e Can be used to operate all 9 o Selectronic fittings and fixtures 3 ja CI CI 1 M968857 REV 1 2 Roughing in Dimensions GENERAL DESCRIPTION TT ai Electronic faucet with proximity operation Colored 14300 e 53 18 LED s signal temperature change mode Vandal resistant solid bras
11. s construction single post mounting Operates on AC permanent power Water pressure range from 20 to 80 psi In line strainer for solenoid is integral Single inlet 3 8 compression built in checks and flexible stainless steel 15 reach inlet hose for ae spout connection EE MAX 7 8 CODES AND STANDARDS 6 7 8 These products meet or exceed the following coded z standards ANSI A117 1 ASME A112 18 1 IA ADA Compliant CSA B 125 NSF 61 Section 9 Qi 90 3 36 1524mm 60 gt 3 8 COM P A TOOLS REQUIRED 1 Channel Locks 5 Flat Blade Screwdriver 2 Adjustable Wrench 6 Electric Drill amp 1 4 Drill Bit 3 Plumbers Putty or 7 Tape Measure Caulking 4 Phillips Screwdriver INSTALLATION fl INSTALL SPOUT ASSEMBLY Fig 1 NUTONE Supplies before beginning 1 Optional Assemble DECK PLATE 1 and PUTTY PLATE 2 to FAUCET BODY 3 with SCREW 4 Fig 1 2 Insert WIRES 5 FLEX HOSE 6 and SPOUT SHANK 7 through center hole of mounting surface Fig 1a 3 Assemble C WASHER 8 and LOCKNUT 9 onto threads of SPOUT SHANK 7 from underside of mounting surface Fig 1b 4 Align FAUCET 3 and tighten LOCKNUT 9 If using DECK PLATE 1 hand tighten DECK PLATE SPIN NUTS 10 to secure FAUCET 3 to mounting surface Fig 1b 2 M968857 REV 1 2 H MOUNT ENCLOSURE Fig 2 1 Determine location of ENCLOSURE 1 It must be located with in the 14 856mm by 21 533m
Download Pdf Manuals
Related Search