American Standard 3305 Indoor Furnishings User Manual
Contents
1. CONTINUES TO LEAK SLOWLY repeat Step 13 IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON USE it is a signal you are wasting water because e The end of the refill tube is inserted into overflow pipe below water level in tank Attach refill tube to overflow pipe using S clip provided e The flush valve is leaking because it s worn dirty or misaligned with tank ball or flapper replace with a new flapper IF FILL VALVE WON T TURN ON OR SHUT OFF or REFILL OF TANK WATER IS SLOW after valve has been in use for some time Fluidmaster Model 242 Replacement Seal may be needed IMPORTANT Always clear e While holding a container e Replace TOP by engaging Go to our website at www fluidmaster com for more sand and rust from system over the uncapped VALVE lugs and rotating 1 8 turn solutions to toilet problems e Make sure water supply is off to prevent splashing turn clockwise MAKE CERTAIN Remove valve TOP by lifting water supply on and off a TIP IS TURNED TO THE o arm and rotating top and arm few times Leave water LOCKED POSITION VALVE 1 8 turn counterclockwise supply off MAY NOT TURN ON IF TOP Fluidmaster lme pressing down slightly on cap IS NOT FULLY TURNED TO 30800 Rancho Viejo Road THE LOCKED POSITION San Juan Capistrano CA 92675 949 728 2000 800 631 2011 GUARANTEE This Fluidmaster product is guaranteed to be free from defective materials and workmanship for a period of www fluidmaster com one year Units returned to Fl2. FLANGE FINISHED WALL LL o CLOSET BOLTS D SUPPLY AS REQ D LL INSTALL CLOSET BOLTS FINISHED Install closet bolts in flange channel turn 90 and slide oc FLOOR into place 6 152 mm apart and parallel to wall O LL NUT a Lu UD WASHER gt lt x CLOSET o BOLT INSTALL WAX SEAL POSITION TOILET ON FLANGE Invert toilet on floor cushion to prevent damage and a Unplug floor waste opening and install toilet on closet flange so bolts project install wax ring evenly around waste flange horn with through mounting holes tapered end of ring facing toilet Apply a thin bead of b Loosely install retainer washers and nuts Side of washers marked THIS sealant around toilet base SIDE UP must face up Aimtrican Lites nasa Sada Standard Stamdard Sandard S amdard edekca Saniwares enai Mea ann ean trademarks of American Standard Inc 7301079 100 Rev B For Tanks Bowls using Speed Connect System Tank mounting bolts pre installed RUBBER TANK MTG GASKET BOLTS PRE BOLT CAP INSTALLED CLOSET BOLT INSTALL TANK a Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening and tank mounting bolts go through mounting holes Secure with metal washer nut combo WASHER NUT INSTALL TOILET a Position toilet squarely to wall and with a rocking motion press bowl down fully on wax ring
3. 9 of installation procedure Poor bowl to tank floor connection Review Step 4 through 7 of installation procedure Toilet does not shut off Flush valve chain too tight holding flush valve open Readjust chain length as needed Review Step 10 Flush valve seat and or flapper worn or deformed Shut off water supply Replace flush valve Sand or debris lodged in water control Shut off water supply Remove cap and clean per Step 13 CADET 3 FLUSH RIGHT TOILET FIVE YEAR LIMITED WARRANTY For this warranty to become effective the accompanying warranty registration card and proof of purchase must be completed and returned to the address on the warranty registration card within 30 days of purchase If inspection of this American Standard plumbing product inclusive of china and all mechanical components within five years after its initial purchase confirms that it is defective in materials or workmanship American Standard will repair or at its option exchange the product for a similar model This warranty does not apply to local building code compliance Since local building codes vary considerably the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before installation This warranty shall be void if the product has been moved from its initial place of installation if it has been subjected to faulty maintenance abuse misuse accident or other da
4. INSTALLATION INSTRUCTIONS Ameri dard CARE AND MAINTENANCE Cra 3 Cadet 3 Toilet featuring the Flush Right system Model 3305 Right Height Elongated Toilet with 12 Rough Tank and Seat Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure this product is installed properly please read these instructions carefully before you begin Certain installations may require professional help Also be sure your installation conforms to local codes A CAUTION PRODUCT IS FRAGILE TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE NOTE Pictures may not exactly define contour of china and components RECOMMENDED TOOLS AND MATERIALS Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure Hacksaw Wax Ring Gasket Flexible Supply Tube Closet Bolts Carpenters Level REMOVE OLD TOILET Close toilet supply valve and flush tank completely Towel or sponge remaining water from tank and bowl Disconnect and remove supply line NOTE f replacing valve first shut off main water supply Remove old mounting hardware remove toilet and plug floor waste opening to prevent escaping sewer gases Remove closet bolts from flange and clean away old wax putty etc from base area NOTE Mounting surface must be clean and level before new toilet is installed Yi ROUGHING IN DIMENSIONS dp NOTE Distance from wall to closet flange centerline must be as listed below CLOSET
5. and flange Alternately tighten nuts until toilet is firmly seated on floor With tank parallel to wall alternately tighten nuts until tank is snugged down A CAUTION gt evenly against bowl surface DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED USE INCLUDED TOOL NUT DRIVER OR DEEP SOCKET RACHET Install caps on washers lf necessary cut bolt height to size before installing caps A CAUTION DO NOT OVERTIGHTEN NUTS MORE Smooth off the bead of sealant around base THAN REQUIRED FOR A SNUG FIT Remove excess sealant Before continuing determine the type of water supply connecation you have from the chart below and use the appropriate assembly parts required to properly reconnect the water supply DO NOT use plumber s putty to seal these fittings VINYL BRAIDED CONNECTOR METAL FLANGED METAL SPIRAL TUBING TUBING E LOCK NUT LOCK NUT PA Lock NUT SPS tock NUT CONE EXISTING EXISTING COUPLING lt WASHER WASHER CONE NUT WASHER COUPLING NUT METAL COPPER FLARED TUBING _ COUPLING _ EXISTING NUT COUPLING NUT WATER WATER WATER SHUT OFF SHUT OFF N SHUT OFF p W7 Captive cone washers already Use existing spiral cone washer Fluidmaster cone included No washer may not additional washers water leakage Water supply seal completely on needed tube or pipe must extend at spiral type sup
6. mage if it was not installed in accordance with American Standard s instructions or if it has been modified in a manner inconsistent with the product as shipped by American Standard This warranty DOES NOT COVER any damage caused by the use of in tank cleaners American Standard s option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation nor shall American Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product all of which are expressly excluded from this warranty Some states or provinces do not allow the exclusion or limitation of implied warranties so this exclusion may not apply to you This warranty gives you specific legal rights You may have other statutory rights that vary from state to state or from province to province in which case this warranty does not affect such statutory rights For service under this warranty it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased or that a service request including a description of the product model and of the defect be sent to the following address In the United States In Canada In Mexico American Standard Inc American Standard Customer Service Manager P O Box 6820 2480 Stanfield Rd Ideal Standard S A de C V Piscataway New Jersey 08855 Mississa
7. nd moving FLOAT CUP up or down When cleaning your toilet wash it with mild soapy water rinse thoroughly with clear water and dry with a soft cloth Avoid detergents disinfectants or cleaning products in aerosol cans NEVER use abrasive scouring powders or abrasive pads on your toilet seat Some bathroom chemicals and cosmetics may damage the seat s finish WARNING Do not use in tank cleaners Products containing chlorine calcium hypochlorite can seriously damage fittings in the tank This damage can cause leakage and property damage American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine calcium hypochlorite Repair parts are determined by toilet tank number which can be found marked inside tank REPAIR PARTS LIST NOTE XXX represents color or trim finish options Specify when ordering PART NO 738903 XXX0A DESCRIPTION TRIP LEVER STANDARD LEFT HAND TANK NUMBER 4021 Cadet 3 with the Flush Right System 034783 XXX0A BOLT CAP KIT 738565 423 0070A 738921 100 0070A FLUIDMASTER 400A VALVE FLUSHVALVE ASSEMBLY 3 INCH INCLUDES FLAPPER 738920 0070A FLAPPER ASSEMBLY 3 INCH 7301021 0070A TANK COUPLING KIT 253 738916 100 0070A REFILL TUBE 5 INCH 735121 400 XXX TANK COVER 12 ROUGH 760062 XXX0A TOILET SEAT 7301079 100 Rev B TROUBLESHOOTING IF FILL VALVE SHUTS OFF BUT
8. ply least 1 2 inside threaded line shank of valve does not apply to flanged tubing Use existing coupling nut and washer These parts must be used as illustrated to insure water tight connection Use of existing coupling nut may result in E With correct washers in place see Step 9a tighten COUPLING NUT 1 4 turn beyond hand tight DO NOT OVERTIGHTEN CAUTION Overtightening of CAUTION DO NOT USE CONE WASHER WITH PLASTIC SUPPLY LINE LOCK NUT or COUPLING NUT could result in breakage and potential flooding 7301079 100 Rev B ARM REFILL NIPPLE Fyi C pur A T IL CRITICAL LEVEL RZ Sn V I MARK C L MUST BE 1 ABOVE OVERFLOW PIPE WATER LEVEL ADJUSTMENTS Adjust water level Water level should be adjusted to level indicated on tank by adjusting float cup See Step 11 for water level adjustment method If bowl fails to siphon an adjustment may be required with the lift chain Simply remove the bead chain from ADJUSTMENT 8 5 r ROD the retainment clip and take up slack on the chain and reinsert on lift rod Make sure the chain is not too taught Turn on water supply CONE WASHER SA COUPLING NUT un HAND TIGHT ONLY PARTS FOR WATER CONNECTION SEE STEP 9 Diagram 1 CARE AND CLEANING Submerge the FLOAT CUP under the water for 30 seconds Adjust the water to desired level by turning WATER LEVEL ADJUSTMENT ROD a
9. uga Ontario Via Morelos 330 Attention Director of Consumer Affairs Canada L4Y 1S2 Col Santa Clara For residents of the United States warranty information Toll Free 800 387 0369 Ecatepec 55540 Edo Mexico may also be obtained by calling the following www americanstandard ca www americanstandard com mx toll free number 800 442 1902 www americanstandard us com we Live 7301079 100 Rev B
10. uidmaster will be replaced without charge Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products Fluidmaster shall not be responsible or liable for any damages caused by products used with Fluidmaster valves that were not manufactured by Fluidmaster Inc For troubleshooting information please contact 2001 Fluidmaster Inc Registered trademark of Fluidmaster Inc TROUBLESHOOTING GUIDE POSSIBLE CAUSE CORRECTIVE ACTION Does not flush Water supply valve closed a Open valve and allow water to fill tank Supply line blocked b Shut off water supply disconnect supply line and inspect all gaskets and washers Reassemble Also see Fluidmaster maintenance see Step 13 Flush valve chain too loose or disconnected c Readjust chain length as required Sand or debris lodged in water control d Shut off water supply Remove cap and clean as per Step 13 Poor or sluggish flush Bowl water level too low a Check that refill tube is connected to water control and inserted into tank overflow without being kinked or damaged Supply valve partly closed Open supply valve fully Be sure that proper supply tube size is used Partially clogged trapway and or drain pipe and or vent Remove obstruction Consult a plumber if necessary Supply pressure too low Normal supply pressure must be at least 20 psi Toilet leaks Poor supply line connection Review Step
Download Pdf Manuals
Related Search