American Standard 2808.222 Indoor Furnishings User Manual
Contents
1. Release POP UP KNOB 5 down and check all drain connections and P trap for leaks m Tighten if necessary CARE INSTRUCTIONS DO SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER DRY WITH A SOFT COTTON FLANNEL CLOTH DO NOT DO NOT CLEAN THE PRODUCT WITH SOAPS ACID POLISH ABRASIVES HARSH CLEANERS OR A CLOTH WITH A COARSE SURFACE To change direction of handle rotation proceed as follows m Turn valve to OFF position Remove INSERT and HANDLE SCREW Slip HANDLE with ADAPTER off Remove SPRING CLIP 1 Lift STOP WASHER 2 turn 90 and replace Replace SPRING CLIP 1 Replace ADAPTER HANDLE SCREW and INSERT Spray may accumulate dirt causing distorted and reduced water flow Remove spray and rinse clean Replace Spray and operate handles several times from OFF to ON position Do not force handles turn only 90 US60385 Rev 1 22. Check DRAIN FLANGE in SINK to ensure that WHITE FOAM GASKET 3 is fully compressed and not visible Fig B POP UP KNOB POP UP KNOB 1 must be fully down REAR OF FLAT SIDE OF GASKET MUST FACE DOWN FLAT SIDE OF GRAY LOCKNUT MUST FACE UP US60385 Rev 1 2 ATTACH CABLE CONNECTOR Thread CABLE CONNECTOR 1 clockwise onto DRAIN BODY CONNECTION 2 and hand tighten Fig A Your new POP UP DRAIN installation is now complete Fig B Note Tailpeice on pop up drain is 1 1 4 O D Fig B CHECK OPERATION OF POP UP Operate LIFT KNOB 1 to verify that STOPPER 2 opens and closes Note If STOPPER 2 does not open and close properly then refer to the troubleshooting section of these instructions MAKE WATER SUPPLY AND WASTE CONNECTIONS NOTE FLEXIBLE SUPPLIES OR BULL NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY Thread TEE BODY 4 to SPOUT SHANK 5 Thread HOSE CONNECTOR 6 GA to VALVE CONNECTIONS 7 7A Connect water supply to VALVE BODIES 1 1A with 1 2 IPS FLEXIBLE SUPPLIES 2 or 3 8 0 D BULL NOSE RISERS 3 Use adjustable wrench to tighten connections Do not over tighten Be careful not to kink copper supply when bending Use tubing cutter to cut to proper length Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant appropriate connectors and COUPLING NUTS Connect 1 1 4 O D tailpiece on POP UP DRAIN to
3. waste outlet 1 Se 3 8 0 D 4 BULL NOSE RISERS 1 2 PIPE THREAD 3 COMPRESSION NUT FLEXIBLE SUPPLIES FERRULE 3 8 COMPRESSION CONNECTION US60385 Rev 1 2 INSTALL HANDLES Push ADAPTER 1 on VALVE STEM 2 so that the hole of the ADAPTER 1 without spline is facing up Thread HANDLE BASE 3 onto VALVE ESCUTCHEON 7 Push LEVER BALL 4 onto ADAPTER 1 Find correct position of HANDLE 4 by adjusting male teeth on ADAPTER 1 to female teeth in LEVER BALL 4 Secure LEVER BALL 4 with HANDLE SCREW 5 Push INDEX CAP 6 ONN in hole of LEVER BALL 4 TEST INSTALLED FITTING INSTALLATION OF OPTIONAL METAL LEVER HANDLES Supplied with Faucet E Thread PORCELIAN LEVER HANDLE 2 counter clockwise and remove INDEX BUTTON with MOUNTING ROD ASSEMBLY 1 E Insert MOUNTING ROD ASSEMBLY 1 into METAL HANDLE 3 and HANDLE COLLAR 4 E Thread HANDLE ASSEMBLY 6 into ball of HANDLE BASE 5 and tighten With HANDLES 1 in OFF position turn on WATER SUPPLIES 2 and check all connections for leaks Remove AERATOR 3 Operate both HANDLES 1 to flush water lines thoroughly Replace AERATOR 3 CHECK DRAIN CONNECTIONS Operate POP UP KNOB 5 and fill Sink with water Check that DRAIN STOPPER 4 makes a good seal and retains water in Sink If STOPPER 4 does not seal properly please refer to Troubleshooting Guide in these instructions
4. Armtrican Standard Installation WilGamsburg ns a08 228 LL ATIS DULG 2908 222 Widespread Lavatory Faucet with the Speed Connect Drain Congratulations on purchasing your American Standard faucet with the Speed Connect Drain a feature found only on American Standard faucets Speed Connect Drain Certified to comply with ANSI A112 18 1 e 1 3 of the parts installs in 1 3 of the time US60385 Rev 1 2 e No tools needed e Never needs adjustment e Guaranteed to seal properly the first time every time Your new American Standard faucet is designed to work only with the Speed Connect drain Helpful tips for removing your current drain can be found in the Troubleshooting section of these instructions To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Recommended tools N ore 3 ee 3 E K ba Screwdriver Channel Locks Adjustable Wrench Tubing Cutter INSTALL SPOUT CAUTION Insert SPOUT 41 and CABLE CONNECTOR 2 ree center hole making sure Fig A the SEAL WASHER 3 is properly seated in SPOUT 1 Assemble RUBBER WASHER 4 BRASS WASHER 5 and LOCKNUT 6 onto SPOUT SHANK 7 from under side of sink Make sure SPOUT 1 is centered in the mounting hole and the slot in the BRASS WASHER 5 faces toward the rear of the sink m Tighten LOCKNUT 6 firmly Fig A INSTALL VALVE BODY Place RUBBER RING 9 into ESCUTCHEON 10
5. Install LOCKNUT 11 onto VALVE BODY 12 From under side of mounting surface install VALVE BODY 12 through valve mounting holes Threads of VALVE BODY 12 should extent at least 5 16 of a inch above mounting surface top Fig B Important Thread ESCUTCHEON 10 onto VALVE BODY 12 until snug against internal stop This is key to the installation If not done the faucet handles won t work correctly If necessary adjust LOCKNUT 11 Hand tighten LOCKNUT 11 to secure VALVE BODY 12 Repeat above steps for opposite VALVE BODY 912A 10 9 MOUNTING SURFACE i 5 146 MIN 11 een 12 wP INSTALL POP UP DRAIN Remove CLEAR PLASTIC COVER 1 Remove CARDBOARD SPACER 2 from under DRAIN POP UP 3 Fig A Drop DRAIN BODY 4 through sink drain hole Make sure WHITE FOAM GASKET 5 is under flange of DRAIN BODY 4 Fig B Note No plumber s putty or caulk is required The CABLE ATTACHMENT POINT 6 must face towards the rear of the SINK Fig B INSTALL BLACK GASKET Install BLACK CONE GASKET 1 onto DRAIN BODY 2 from below Note The flat side of the BLACK CONE GASKET 1 must face down INSTALL GRAY LOCKNUT Install GRAY LOCKNUT 4 onto DRAIN BODY 2 from below SINK Fig A Note The flat side of the GRAY LOCKNUT 1 must face up Tighten firmly by hand No tools are required
Download Pdf Manuals
Related Search