American Power Conversion 3U Rack Mount Power Supply User Manual
Contents
1. 2 Locate the white cord attached to one of the battery tray connector plugs Grasp the cord and pull firmly toward you until the connector plug is discon nected o DO NOT pull the battery cables Use a screwdriver to remove the two battery pack mount screws located at the top corners of the bat tery tray face plate Set the screws aside in a safe place You will replace them later Locate the battery tray handle 5 Be careful during this step the tray is heavy Pull the battery tray handle toward you to slide the tray out of the battery pack DO NOT pull on battery cables or white cord 6 Return the battery tray to APC 7 Supporting the new battery tray on the bottom align it with the opening and slide the tray into the com partment Replace the two screws to secure the battery pack face plate Locate the battery cables and the UPS battery connector jack to the right of the battery tray 10 Connect the battery connector plug to the jack Push the plug into the jack so the metal pieces inside each part are touching Press firmly to ensure a tight con nection You will hear a snap when the battery connector plug is seated properly 11 Push the battery cables and white cord as close to the battery tray as possible 12 Repeat Steps 2 through 11 to remove and replace the other battery tray 13 Hold the bezel with the cut2. 1 in qe alae Bon DE EAAS Jll S vv XX K XxX gt oh Battery Pack Use the battery pack connector to daisy chain multiple battery packs to the same Connector UPS The connector is color coded and keyed to prevent improper connection Connection Attach the connection cable plug into a battery pack connector on either the UPS Cable or another battery pack The connector is color coded and keyed to prevent im proper connection Connector The connector plug is shipped installed in the battery pack connector A similar Plug plug is shipped installed in the UPS The plug should only be removed when con necting battery packs INSTALLING THE BATTERY PACK To install one or multiple battery packs follow these basic steps Details of each step follow this list 1 Install the mounting rails in the rack 2 Remove the battery trays from the battery pack 3 Mount the battery pack in the rack Install the battery pack at or near the bottom of the rack Position it below the UPS 4 Reinstall the battery trays and attach the front bezel 5 Connect the battery pack to the Smart UPS or another battery pack INSTALLING THE MOUNTING RAILS IN THE RACK Install the mounting rails in the rack Directions are included with the rail kit The battery pack comes with standard 19 inch 46 5 cm rack mounting rails brackets and cleats The rack can have any of the common types of equipment mounting holes square round threaded o
3. UPS Service must be stopped 2 Go to Program Manager gt Accessories gt Terminal Double click on the Terminal icon 3 Select the COM port to which the black colored interface cable is attached as the Connector The COM port settings are 2400 baud 8 data bits 1 stop bit no parity flow control is Xon Xoff 4 Click OK 5 Once the terminal window is open follow these steps Commano RESPONSE Subtracts a battery pack o Subtracts a battery pack To see the change in number of external battery packs USING THE HYPERTERMINAL PROGRAM TO CHANGE THE NUMBER OF EXTERNAL BATTERY PACKS 1 EXIT the PowerChute plus Server In Windows NT the UPS Service must be stopped 2 From the Desktop go to Start gt Programs gt Accessories gt HyperTerminal Double click on the HyperTerminal icon 3 You are prompted to choose a name and select an icon Enter name and then click OK Disregard the message must install a modem 1f it is displayed 4 Select the COM port The port settings are 2400 baud 8 data bits 1 stop bit no parity flow con trol is Xon Xoff 5 Click on Advanced and ensure the box labeled FIFO buffer is NOT checked 6 Once the HyperTerminal window is open follow these steps Commano RESPONSE oe To see the change in number of external battery packs Subtracts a battery pack To see the change in number of external battery packs 4 STORAGE AND REPLACEMENT STORAGE COND
4. a Singapor Se u Indus ak He a 215001 uy aneen need Importer s Name and Address meri er Les on A P C b v Ba allyor aerate sa Park Galway Irela nd Place N Billerica MA U S ae Pf fi an 01 Richard J Everett Sr Regulatory Compliance Engineer 5 A ha 5 Jan 01 kay B Ballard Managin rope Phone 353 917 02000 ae 383 suas 6909 Place Galway Ireland LIMITED WARRANTY American Power Conversion APC warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase Its obligation under this warranty is limited to repairing or replacing at its own sole option any such defective products To obtain service under warranty you must obtain a Returned Material Authorization RMA number from customer support Products must be returned with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase This warranty does not apply to equipment that has been damaged by acci dent negligence or misapplication or has been altered or modified in any way This warranty applies only to the original purchaser who must have properly registered the product within 10 days of purchase EXCEPT AS PROVIDED HEREIN AMERICAN POWER CONVERSION MAKES NO WARRANTIES EXPRESSED OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Some states do not permit li
5. battery packs supported by the UPS In addi tion battery pack connectors are color coded and keyed to prevent improper connection BATTERY PACKS UNPACKING 1 Inspect the battery pack upon receipt APC designed robust packaging for your product How ever accidents and damage may occur during shipment Notify the carrier and dealer if there is damage The packaging is recyclable save it for reuse or dispose of it properly 2 Check the package contents The shipping package contains the battery pack its front bezel packaged separately mounting rails mounting cleats hardware packet necessary for rack mounting and a literature kit containing product documentation The battery pack is shipped with the front bezel removed packaged separately within the main box You will install the plastic bezel described later during the installation procedure POSITIONING THE BATTERY PACK Place the rack and the battery pack where they will be used The battery pack is heavy Select a location sturdy enough to handle the weight Consider that you must install the battery pack in a protected area that is free of excessive dust and has adequate airflow Ensure the air vents on the front and rear of the battery pack are not blocked Allow at least one inch of space on both sides Do not operate the UPS where the temperature and humidity are outside the specified limits Refer to Specifications at the APC web site PLACEMENT 2 5 cm
6. Arc www apec com User s Manual English APC Smart UPS 3U Rack Mount External Battery Pack 990 1056A 08 01 1 SAFETY INFORMATION American Power Conversion Corporation APC is the leading national and international manufac turer of state of the art uninterruptible power supplies redundant switches power management soft ware and related equipment APC products protect hardware software and data from the threat of power disturbances in business and government offices throughout the world The APC 3U Rack Mount Battery Pack connects to an APC Uninterruptible Power Supply UPS and provides extended protection from electrical blackouts brownouts sags and surges Changes or modifications to this unit not expressly approved by the party respon sible for compliance could void the warranty HANDLING SAFETY Be careful Do not lift heavy loads without assistance lt 18 kg lt 40 Ib i i 32 55 kg 70 120 Ib l i 18 32 kg 40 70 1b gt 55 kg gt 120 Ib m This equipment is intended for installation in a temperature controlled indoor area free of conduc tive contaminants Refer to Specifications at the APC web site for the actual temperature range LIFE SUPPORT APPLICATION POLICY As a general policy APC does not recommend the use of any of its products in life support applica tions where failure or malfunctions of the APC product can be reasonably expected to cause failure of the life support device o
7. ITIONS Store the battery pack covered and flat rack mount orientation in a cool dry location with its bat tery fully charged Disconnect any cables connected to the computer interface port to avoid unneces sarily draining the battery EXTENDED STORAGE At 15 to 30 C 5 to 86 F charge the batteries every six months At 30 to 45 C 86 to 113 F charge the batteries every three months REPLACING A BATTERY TRAY The battery pack has two easy to replace hot swappable battery trays Battery tray replacement is a safe procedure isolated from electrical hazards You may leave the battery pack connected to the UPS with the protected equipment on for the following procedure See your dealer or contact APC for information on replacement battery tray RBC 27 See the APC website http www apc com support to confirm the correct replacement battery tray number RBC and to see other options BATTERY TRAY REPLACEMENT PROCEDURE The battery trays are accessible from the front of the battery pack This procedure requires a Phillips screw driver 1 Remove the front bezel Use both hands and grasp the finger clips on either side of the bezel Pull it to ward you The bezel will unsnap from the battery pack Set the bezel aside you will reinstall it later Although both battery tray compartments are visible Steps 2 through 11 describe how to remove and replace one battery tray Repeat the steps for the other tray
8. an one battery pack is used remove the rear connector plug from the battery pack connected to the UPS connector on the back of the other battery pack The example at left shows two external battery packs 2 Insert the battery pack connector into the rear properly connected to the UPS 060605060 RSL5RR0R6 S6Q58526596 02028282525 OO rHO O TO TO M 530 oO Vv na CE 5 oQ Be iD sE go cD as 5 O 2 2 2 or lt o QO gt g 2 9 4 os lt a O o N ss 2 2 fae no AZ S a amp gt U D 3 o g OD o S ao T 5 2 A O 2 W EKE an Zi e Z af Loan gt o ji k aJ o o oo oo oo oo co oo 3 OPERATING THE SMART UPS WITH A BATTERY PACK SETTING THE SMART UPS TO RECOGNIZE THE BATTERY PACK S Smart UPS XL models cannot determine how many external battery packs are connected to them You must program the Smart UPS XL with the appropriate number of external batteries in one of four ways using Smart UPS Battery Pack Utility BATTPACK a PowerChute plus Version 5 x for Windows 95 Windows 98 Windows NT Terminal Program to Change the Number of External Battery Packs HyperTerminal Program to Change the Number of External Battery Packs Each method is described in this section USING THE SMART UPS BATTERY PACK UTILITY BATTPACK You can use
9. d to prevent improper connec tion The color of the connector on the UPS must match the color of the battery pack connector Allow the battery pack to charge for 24 hours Do not expect full run time during this initial charge period 1 Remove the rear connector plug from the UPS I c N OD i Q eal gt QO Q 9 O fae oO e gt ro D Q Eh lt N D fae QO 3 Q gt gt We oO gt 3 2 E al oO gt D oO e ro fae N a D lt lt O aa nected on the battery pack Removal of this plug connector on the back of the UPS will cause the battery to be disconnected 2 Facing the rear of the battery pack locate the battery pack connector 3 Insert the battery pack connector into the rear 4 Be sure the rear connector plug remains con refer to the proce dure below Connecting a Battery Pack to Another Battery Pack 9 If multiple battery packs are used The example at left shows one battery pack properly connected to the UPS Note that the rear connector plug in the Battery Pack is not removed CONNECTING A BATTERY PACK TO ANOTHER BATTERY PACK gt Q Era Wa N QO R Q gt gt O gt fae O Q O z gt lt fae fae O O 9 O fae O gt O gt 1 When more th
10. ge sus tained in transit is not covered under warranty Always DISCONNECT THE BATTERY before shipping in compliance with U S Department of Transportation DOT regulations 5 Mark the RMA on the outside of the package 6 Return the unit by insured prepaid carrier to the address given to you by Customer Service CONTACTING APC 5 CONTACT AND WARRANTY INFORMATION Refer to the information provided at the APC Internet site http www apc com support contact DECLARATION OF CONFORMITY CE 2001 EC Declaration of Conformity We the undersigned de clare under sole responsibility that the equipment specified below conforms to the following deinen nd directiv Standards to Which Conformity Declared EN50091 1 EN60950 EN50091 1 1 IEC60950 EN55022 EN50091 2 EN61000 3 2 EN61000 3 3 Application of Council Directives 73 23 EEC 93 68 E EC Parise 92 3 1 EEC 93 68 EEC 91 157 EEC Type of Equipment Uninterruptible Power Supply Model Numbers SU48RMXLBP3U Manufacturer s Name and Address American Power So om 132 Fairgrounds Ri een ae ere eee pee Power Conversion A P C b v Ballybritt Business Park Galway Ireland or American Pow oe Ma Ros Cav rike Philippine or American Power Conversior 2nd Street Peza Cavite Economic Zi Rosario Cavite Philippines or Am n Power Con Le 32 Phas e 1 Carmelra iba strial Pai Canluba ie ala aed a Philippine or eb So zho sete WW Ltd 9 Su d Chin
11. mitation or exclusion of implied warranties there fore the aforesaid limitation s or exclusion s may not apply to the purchaser EXCEPT AS PROVIDED ABOVE IN NO EVENT WILL APC BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE Specifically APC is not li able for any costs such as lost profits or revenue loss of equipment loss of use of equipment loss of software loss of data costs of substitutes claims by third parties or otherwise Entire contents copyright 2001 by American Power Conversion Corporation All rights reserved Reproduc tion in whole or in part without permission is prohibited APC Smart UPS and PowerChute are registered trademarks of American Power Conversion Corporation All other trademarks are the property of their respective owners
12. out section on the right Align the tabs on the side of the bezel with the slots on the front of the battery pack and gently snap it into place 12 SERVICE If the unit requires service do not return it to the dealer Instead follow these steps 1 Review the problems discussed in the Troubleshooting section of the User s Manual for your UPS to eliminate common problems 2 Verify that no circuit breakers are tripped A tripped circuit breaker is the most common problem 3 Ifthe problem persists call APC Customer Service or visit the APC website www apc com Note the model number of the unit the serial number and the date purchased If you call APC Customer Service a technician will ask you to describe the problem and try to solve it over the phone if possible If this is not possible the technician may arrange for the unit to be ser viced or may issue a Returned Material Authorization Number RMA m Ifthe unit is under warranty repairs are free If not there is a repair charge Procedures for servicing or returning your unit may vary internationally Please contact the APC Customer Service office in the appropriate country www apc com support for ques tions about warranty and RMA 4 Pack the unit in its original packaging If the original packing is not available ask APC Customer Service about obtaining a new set Pack properly to avoid damage in transit Never use Styrofoam beads for packaging Dama
13. pack to support the unit Each side of the battery pack has a cleat that must slide into the groove on the rails Insert each cleat into its groove and slide the battery pack into position Use the four ornamental screws supplied with the battery pack to attach the mounting brackets to the rack post Insert the screws into the top and bottom holes in the U space REINSTALLING THE BATTERY TRAYS AND ATTACHING THE FRONT BEZEL 1 Supporting the battery tray on the bottom align it with the battery pack opening and slide the tray into the compartment Replace the two screws to secure the battery pack face plate Locate the battery cables and the UPS bat tery connector jacks to the right of each bat tery tray To connect the battery connector plug to the battery jack push the plug into the jack so the metal pieces inside each part are touching Press firmly to ensure a tight connection You will hear a snap when the connector is seated properly Push the battery cables and white cord as close to the battery tray as possible The battery pack is shipped with the front bezel removed it is packaged separately within the main box Unpack the bezel and hold it with the cutout section on the right Align the tabs on the side of the bezel with the slots on the front of the battery pack and gently snap it into place Battery pack connectors are color coded and keye
14. r round non threaded All necessary hardware is provided REMOVING THE BATTERY TRAYS FROM THE BATTERY PACK The battery pack is heavy To lighten it remove the battery trays before mounting the unit in the rack The battery trays are accessible from the front of the battery pack shown at left This procedure requires a Phillips screwdriver n O OC O ooog O OC O ooog O 0 0O d ooog o00 ele O 5 O80 o95 1 Notice that the two battery tray compartments are visible This procedure describes how to re move one battery tray 2 Locate the white cord attached to the battery tray 4 U connector plug Grasp the cord and pull firmly toward you until the connector plug is discon l nected DO NOT pull the battery cables 3 Use a screwdriver to remove the two battery pack mount screws located at the top corners of the face plate Set the screws aside in a safe place You will re place them later Locate the battery tray handle ooo EI Ss EA see cs 3 Hil E j 5 Be careful during this step the battery tray is heavy Pull the battery tray handle toward you to slide the tray out of the battery pack DO NOT pull on battery cables or white cord Repeat Steps 2 through 5 to remove the other the other tray Supporting the battery pack on both sides care fully align the unit with the rails Use the handles on the side of the battery
15. r to significantly affect its safety or effectiveness APC does not recom mend the use of any of its products in direct patient care APC will not knowingly sell its products for use in such applications unless it receives in writing assurances satisfactory to APC that a the risks of injury or damage have been minimized b the customer assumes all such risks and c the liability of APC is adequately protected under the circumstances Examples of devices considered to be life support devices are neonatal oxygen and analyzers nerve stimulators whether used for anesthesia pain relief or other purposes autotransfusion devices blood pumps defibrillators arrhythmia detectors and alarms pacemakers hemodialysis systems peritoneal dialysis systems neonatal ventilator incubators ventilators for both adults and infants anesthesia ventilators infusion pumps and any other device designated as critical by the U S F D A Hospital grade wiring devices and leakage current may be ordered as options on many APC UPS systems APC does not claim that units with this modification are certified or listed as Hospital Grade by APC or any other organization Therefore these units do not meet the requirements for use in direct patient care BATTERY SAFETY This equipment contains potentially hazardous voltages that may cause personal injury if handled incorrectly This equipment must be installed and serviced only by qualified electrical
16. service personnel This equipment contains potentially hazardous voltages Do not attempt to disassemble the unit The unit contains no user serviceable parts Repairs are to be performed only by factory trained service personnel Do not dispose of batteries in a fire The batteries may explode Do not open or mutilate batteries They contain an electrolyte that is toxic and harmful to the skin and eyes Do not connect the terminals of a battery or battery pack with a wire or other electrically conduc tive objects To avoid personal injury due to energy hazard remove wristwatches and jewelry such as rings when replacing the batteries Use tools with insulated handles Replace batteries with the same number and type of batteries as originally installed in the equip ment BATTERY REPLACEMENT AND RECYCLING See your dealer or visit the APC web site www apc com support for information on replacement battery kits and battery recycling d Be sure to return the spent battery to APC for recycling Ship it to APC in the re placement battery packing material 2 INSTALLING THE BATTERY PACK The APC 3U Rack Mount Battery Pack provides extended protection to safeguard your computer and other valuable electronic equipment The external battery pack also provides extra protection while replacing the batteries in the UPS MAXIMUM NUMBER OF BATTERY PACKS SUPPORTED BY THE UPS The following table indicates the maximum number of
17. the BATTPACK program with DOS or at a Microsoft Windows DOS prompt BATT PACK cannot be used with a DOS emulator or VDM virtual DOS machine like those in Windows 95 Windows 98 or Windows NT You must use the APC UPS Link cable to communicate to the UPS Use either of two black cables part numbers 940 0024C or 940 1524C At the DOS prompt type battpack com X Y where X represents the available serial port the Battery Pack Utility uses to access the Smart UPS Y represents the number of external battery packs In the following example the black cable is attached to communication port 1 There are four exter nal battery packs The program confirms that the update is successful C gt battpack com 4 USING POWERCHUTE PLUS VERSION 5 X FOR WINDOWS 95 WINDOWS 98 WINDOwS NT PowerChute plus 5 x for Windows NT is compatible with NT 3 5 1 SP5 NT 4 0 Workstation at least SP1 or NT 4 0 Server at least SP1 1 Install the software per the instructions on the CD After rebooting the computer access the Pow erChute plus graphical user interface Click on Configuration Click on UPS Operating Parameters Adjust the External Battery Pack field to the appropriate number of external battery packs Click OK a SS USING THE TERMINAL PROGRAM TO CHANGE THE NUMBER OF EXTERNAL BATTERY PACKS Terminal is used in Windows 3 1x Windows for Workgroups and Windows NT 3 51 1 EXIT the PowerChute plus Server In Windows NT the
Download Pdf Manuals
Related Search