American DJ XP3 DJ Equipment User Manual
Contents
1. To next DMX unit or terminate American DJ www americandj com XP 3 Instruction Manual Page 8 XP 3 Controls and Functions TOP OO A WP BOTTOM American DJ www americandj com XP 3 Instruction Manual Page 9 XP 3 Controls and Functions 1 Lens This is a fully focusing high quality lens Focus the lens by manually turning the lens in a clockwise or counter clockwise direction until the image is in focus 2 XLR Output Jack This jack is used to transmit the incoming DMX signal to another DMX fixture or transmit a Master Slave signal to the nest XP 3 in the chain For best results in DMX or Master Slave mode terminate this jack if it is the last unit in the chain See Terminator on page 7 3 XLR Input Jack This jack is used to accept an incoming DMX signal from a universal DMX controller or Master Slave from the output jack of another XP 3 signal 4 MINI C Controller Jack This jack is for use with the optional MINI C Blackout controller only See page 7 for details on the MINI C controller Do not attempt to con nect an audio signal this jack this will damage the PC board and void your manufactures warranty 5 Power Cord Connection The power connection uses an I E C type connector use only a power cord that matches this type of connection Be sure to only connect this unit to a power outlet that matches the printed power label on2. Also never move the fixture until the lamps have had ample time to cool Remember lamps are not covered under war ranty conditions Fuse amp Lamp Replacement Caution Always replace with the exact same type lamp and fuse unless otherwise specified by an authorized American DJe technician Replace with anything other than the specified part can damage your unit and will void your manufactures warranty Warning If after replacing the lamp or fuse either one continues to blow STOP using the unit Contact customer support for further instructions you may have to return the unit for servicing Continuing to use the unit may cause serious damage Fuse Replacement Disconnect the units main power supply Insert a standard flat head screw driver in to the fuse holder housing Turn the screwdriver in counter clockwise direction to remove the fuse holder Remove the fuse holder to expose the fuse Remove the old fuse and discard it Replace the fuse with the same type Insert the fuse holder back into it s housing and turn it in clockwise direction to lock the holder in place Lamp Replacement Caution Never attempt to change the lamp while the fixture is plugged in Always disconnect the main power and allow the unit ample time to cool before attempting to replace the lamp Lamp replacement has been made simple by incorporating the use of a flip up front cover that is retained by thumb screws 1 Be sure to follow the proper handli
3. Stand Alone Operation Sound Active This function allows a single unit to run to the beat of the music Only use this function when running a single unit or when running several units as individuals Please note this function does not allow individual control of the DMX traits and will only run to the units built in programs Master Slave Settings Small Pattern On Sound Active Big Pattern On Sound Active 1 To activate the Sound Active mode use the function button to select either a large or small program pattern See Master on the function button chart above Large or Small is used to refer ence the room size the unit will be used in A large program type will use programs that cover a wide area and small program type will use programs that cover a narrow area 2 The unit will now react to the low frequencies of music via the inter nal microphone 3 Adjust the audio sensitivity knob on the side of the unit to make the unit more or less sensitive to sound Turning the sensitivity knob in the clockwise direction will increase the sensitivity turning the knob American DJ www americandj com XP 3 Instruction Manual Page 12 XP 3 in the counter clockwise direction will decrease the fixture s sensi tivity to sound 4 The optional MINI C Blackout Controller may be used in this mode to control blackout Note Stand Alone ooeration reguire sound to activate The units will
4. The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion 3 Pin XLR Female Out 5 Pin XLR Male In e enor s American DJ www americandj com XP 3 Instruction Manual Page 6 XP 3 Linking Master Slave Linking For a more dramatic effect link several XP 3 together Your fixture comes with built in programs These programs are designed to work with up to 4 units when daisy chained together in a master slave con figuration Any unit can function as either a Master Unit or a Slave Unit Link the units together using standard DMX cable as described on pages 5 and 6 Optional MINI C blackout controller To next XP 3 if applicable Optional MINI C The optional MINI C controller allows all units linked together to blackout This unit will only blackout the fixtures and will not change or select different pro grams 30 Foot Extension Cable Blackout Indicator Blackout Button American DJ www americandj com XP 3 Instruction Manual Page 7 XP 3 Linking DMX Linking DMX function allows independent control of each fixture Use any uni versal DMX controller to access the different traits associated with the XP 3 A reference of different DMX traits is printed on page 21 of this manual Link the units together using standard DMX cable as described on pages 5 and 6
5. Use a brush to wipe down the cooling vents and fan grill 3 Clean the external optics and mirror with glass cleaner and a soft cloth every 20 days 4 Clean the internal optics with glass cleaner and a soft cloth every 30 60 days 5 Always be sure to dry all parts completely before plugging the unit back in XP 3 Trouble Shooting Trouble Shooting Listed below are a few common problems that you may encounter with solutions Cleaning No light output from the unit 1 Be sure you have connected your unit into a standard 120V wall outlet 2 Be sure the external fuse has not blown The fuse is located on the bottom panel of the unit 3 Remove the lamp cover and be sure the lamp is seated in its socket properly Occasionally lamps become loose during shipping be sure the lamp is push in to its socket all the way 4 Be sure the fuse holder is completely and properly seated Unit does not respond to sound 1 Low frequencies bass should cause the unit to react to sound Tapping on the microphone quiet or high pitched sounds may not activate the unit 2 Be sure the SENSITIVITY KNOB 5 is not set to the minimum position American DJ www americandj com XP 3 Instruction Manual Page 18 Halogen Lamp Warning This fixture is fitted with halogen lamps which are highly susceptible to damage if improperly handled Never touch the lamps with your bare fingers as the oil from your hands will shorten lamp life
6. XP 3 Instruction Manual Page 23 Web www americandj com E mail info americandj com
7. blackout in this mode to conserve bulb life when there 1s no sound pres ent Operation Master Slave Operation Sound Active This function will allow you to link up to 4 units together and operate to the built in pro grams without the use of an external controller The units will all oper ate to sound via the Master units internal microphone and sound sensitivity setting In Master Slave operation one unit will act as the controlling unit and the others will react to the controlling units pro grams Any unit can act as a Master or as a Slave Please note this function does not allow individual control of the DMX traits and will only run to the units built in programs 1 Using standard XLR microphone cables as described on pages five and six daisy chain your units together via the XLR connectors on the rear of the units Remember the Male XLR connector is the input and the Female XLR connector is the output The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector only For longer cable runs we suggest a terminator at the last fixture 2 Follow the chart at the end of this section for proper addressing 3 Use the chart on the next page to set the program type either large or small Large or Small is used to reference the room size the unit will be used in A large program type will use programs that cover a wide area and small program type will use pr
8. not spill water or other liquids into or on to your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside Never plug this unit in to a dimmer pack Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged This unit is intended for indoor use only use of this product outdoors voids all warranties During long periods of non use disconnect the unit s main power Always mount this unit in safe and stable matter Power cords should be routed so they are not likely to be walked on pinched by items placed upon or against them Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 7 for cleaning details Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat e The fixture should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has bee
9. NI C black out controller may be purchased separately Customer Support American DJe provides a toll free customer sup port line to provide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www americandj com for any comments or suggestions Service Hours are Monday through Friday 9 00 a m to 5 00 p m Pacific Standard Time Voice 800 322 6337 Fax 323 582 2610 E mail support americandj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures war ranty In the unlikely event your unit may require service please contact your nearest American DJe dealer American DJ Supply www americandj com XP 3 Instruction Manual Page 2 XP 3 Safety Precautions Safety Issues This unit may blow a fuse if the maximum allotted load of 5 amps is reached If the fuse needs replacement always replace the fuse with same exact type that was remove unless other wise instructed by an authorized American DJe service technician Use of a different type fuse from that which is recommended may cause fire or electric shock and will void the manufactures warranty To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do
10. Revised 01 02 User Instructions American Dho 4295 Charter Street Los Angeles Ca 90058 www americandj com General Information General instructions To optimize the performance of this product please read these operating instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain impor tant safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference Unpacking Thank you for purchasing the XP 3 by American DJe Every XP 3 has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact In the case damage has been found or parts are missing please contact our toll free customer support number for further instructions Do not return this unit to your dealer without first contacting customer support Introduction The XP 3 is a unique intelligent fixture with a rotat ing head unit This unit may be operated in three modes DMX 512 Stand Alone or Master Slave The XP 3 comes with several build in programs and is best used in multiples of four or more This piece is best used with a fog or haze machine to enhance the beam output An optional MI
11. Switch 2 Inverted Tilt When activated this switch will invert the TILT value Up will become down and vice versa Dipswitch Functions 1 Pan Inverted Tilt Inverted 13 Function Buttons These buttons serve two functions When the unit is to be used as the master unit in master slave mode these switches are used to assign the program pattern type either large or small In when the used is to be used as a Slave or when in DMX mode these buttons are used to assign a DMX address to the unit Function Buttons Key 1 Function Key F01 And F02 And DMX Address Change Key 2Up Key DMX Address Up Counter 3 Down Key DMX Address Down Counter American DJ www americandj com XP 3 Instruction Manual Page 11 Operation Operating Modes The XP 3 may be operated in three different modes e Stand alone mode The unit will react to sound chasing through the several built in programs You can also use the optional MINI C remote to control a blackout function e Master Slave mode You can daisy chain up to 16 units together to get a synchronized light show that will react to sound chasing through several built in programs You can also use the optional MINI C remote to control a blackout function e DMX control mode This function will allow you to control each individual fixtures traits with a standard DMX 512 controller such as the American DJ DMX Operator or Show Designer
12. a copy of your proof of purchase invoice You may obtain a R A number by contacting our customer support team on our toll free customer support number at 800 322 6337 All packages returned to service not displaying a R A number on the outside of the package will be returned to the shipper American DJ www americandj com XP 3 Instruction Manual Page 4 XP 3 Set Up Power Supply Before plugging your unit in be sure the source voltage in your area matches the required voltage for your American DJe XP 3 Because line voltage may vary from venue to venue you should be sure your unit voltages matches the wall outlet voltage before attempting to operate you fixture DMX 512 DMX is short for Digital Multiplex This is a universal protocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fixture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The orde
13. actory unless prior written authorization was issued to purchaser by Ameri can DJe if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintenance cleaning or periodic check up During the period specified above American DJo will replace defec tive parts at its expense and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of American DJe under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of American DJ All products covered by this warranty were manufactured after January 1 1990 and bear identifying marks to that effect E American DJe reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured F No warranty whether expressed or implied is given or made with respect to any acces sory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by American DJe in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of mer chantabilit
14. age 19 for details on the 2 Color Strobe Function and channel five controls the shutter and general strobe function Page 13 details the different DMX traits in depth 2 To control your fixture in DMX mode follow the set up procedures American DJ Supply www americandj com XP 3 Instruction Manual Page 14 XP 3 Operation on pages 5 7 as well as the set up specifications that are included with your DMX controller 3 Use the DMX controller s faders to control the various DMX fixture traits 4 This will allow you to create your own programs 5 When using a DMX controller and setting up for DMX operation follow the DMX addressing procedure in your controller s manual All fixtures must follow a specific DMX addressing protocol for proper operation in DMX mode 6 For help operating in DMX operation consult the manual included with your DMX controller 7 For longer cable runs more than a 100 feet use a terminator on the last fixture XP 3 Mounting The XP 3 ships with a built in rigging point and two large holes in the base of the unit that are to be used for safety cables The rigging point is located on the bottom of the unit This rigging point is secured to the fixture by two large Phillips screws When the rigging point is not to be used and when the fixture is shipped from the manufacture the point is shipped inverted When the fixture is to be hung by truss or other means please use the rigging point a
15. n spilled into the appliance C The appliance has been exposed to rain or water D The fixture does not appear to operate normally or exhibits a marked change in performance American DJ www americandj com XP 3 Instruction Manual Page 3 XP 3 Features e Micro Stepping Motors for Smooth Transitions e Uses Five DMX Channels e DMX 512 Protocol Compatible Full Focusing e Fan Cooled e 17 Color Gobo Combinations Plus Spot Strobes in Every Color Built In Programs e Room Type Function for Built In Programs e 355 Pan 240 Tilt e 2 Color Strobe Function e Digital Display e Master Slave Operation Linkable up to Four Units e Built In Lamp Shut Off Protection Internal Microphone e Volume Sensitivity Knob e Built In Rigging Point Easy Lamp Replacement e Long Life ZB JCR H5 15v 150w Lamp 500 Hours e Optional MINI C Blackout Controller Product Registration The XP 3 carries a one year 865 days limited warranty Please fill out the enclosed warranty card to validate your purchase All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number The R A number must be clearly written on the outside of the return package A brief description of the problem as well as the R A number must also be written down on a piece of paper and included in the shipping container If the unit is under warranty you must provide
16. nd secure the fixture with safety cables Always be sure to firmly secure the rigging point to the unit The XP 3 can be mounted to a wall or may hung from truss American DJ www americandj com XP 3 Instruction Manual Page 15 XP 3 DMX Traits The chart below details the DMX traits in depth The individual trait can only be accessed by using an universal DMX controller Note The gobo patterns can be found on the next page XP 3 DMX TRAITS CHANNEL 1 CHANNEL 2 CHANNEL 3 CHANNEL 4 CHANNEL 5 PAN TILT GOBO COLOR 2 COLOR GOBO STROBE STROBE SHUTTER 255 255 255 Speed Slow 1 fps 255 240 255 j Large White Spot 239 Fast 239 239 Speed Fast 10 fps 239 240 255 Open 129 255 Any Color Gobo Up 152 Slow 152 144 151 Gobo 17 Dk Blue Speed Fast 7 fps 129 136 143 Gobo 16 Green a Strobe 128 135 Gobo 15 Pink Speed Fast 7 fps 128 120 127 Gobo 14 Orange 112 119 Gobo 13 Lt Blue Yellow 104 111 7 Gobo 12 Yellow 96 103 Gobo 11 Lt Blue 88 95 Gobo 10 White 80 87 Gobo9 Red Green Yellow Lt Blue 7219 F Goboe Fupie Any Color Gobo Down 64 71 Gobo7 Red Green 56 63 Gobo6 Orange 48 55 Gobo5 Lt Blue 40 47 Gobo4 Yellow 32 39 Gobo3 Green 24 31 Gobo2 Blue 16 23 t Gobo1 Red Speed Slow 2 fps 16 00 15 t Large White Spot Speed Slow 1 f
17. ng procedures that deal American DJ www americandj com XP 3 Instruction Manual Page 19 Fuse amp Lamp Replacement with halogen lamps Never touch the new lamp with your bare fingers 2 Remove the thumb screw on the rear of the unit s head This screw hold the lamp socket cover in place 3 Pull back the cover once the screw has been removed to access the socket assembly 4 Carefully remove the old lamp and discard it in the trash 5 Replace the lamp with an exact match and reassemble Lamp Socket Assembly Thumb Screw __ Lamp Cover Fuse American DJ www americandj com XP 3 Instruction Manual Page 20 Master Slave Quick Reference Chart The charts below details the Master Slave setting for Master Slave configuration Use this configuration when you will be using two or more fixtures in a Master Slave configuration The Master Head 1 settings should only be used once Master Slave Settings Small Pattern On Sound Active Big Pattern On Sound Active Slave 1 Address 01 Slave 2 Address 06 Address 06 Function Buttons Key 1 Function Key F01 And F02 And DMX Address Change Key 2Up Key DMX Address Up Counter 3Down Key DMX Address Down Counter Dipswitch Functions 1 Pan Inverted Tilt Inverted American DJ www americandj com XP 3 Ins
18. ograms that cover a narrow area 4 Adjust the audio sensitivity knob on the side of the unit to make the unit more or less sensitive to sound Turning the sensitivity knob in the clockwise direction will increase the sensitivity turning the knob in the counter clockwise direction will decrease the fixture s sensitivity to sound 5 The optional MINI C Blackout Controller may be used with this function for blackout Note Master Slave operation reguire sound to activate The units will American DJ Supply www americandj com XP 3 Instruction Manual Page 13 Operation blackout in this mode to conserve bulb lite when there 1s no sound pres ent Master Slave Settings Small Pattern On Sound Active Big Pattern On Sound Active Slave 1 Address 01 Slave 2 Address 06 Slave 3 Address 06 Universal DMX Control This function allows you to use a universal DMX 512 controller such as the American DJe DMX Operator or Show Designer to control head movement the color gobo wheel and other functions Operating through a DMX controller allows you the freedom to create unique and customized programs tailored to your specific individual needs 1 The XP 3 uses five DMX channels Channel one controls pan channel controls tilt channel three controls the color gobo wheel channel four control a unique 2 Color Strobe function see p
19. outer casing Grounding the shield could cause a short circuit and erratic behavior e XLR Male Socket XLR Female Socket 1 XLR Pin Configuration l I 1 Ground 2 Cold 2 Cold 1 Ground Pin 1 Ground I I Pin 2 Data Compliment negative i I I I I I l Pin 3 Data True positive Figure 2 COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 90 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number ZDMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems O and interference It is always advisable D 3 to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture Figure 4 Figure 3 5 Pin XLR DMX Connectors Some manufactures use 5 pin XLR connectors for DATA transmission in place of 3 pin 5 pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores
20. ps 01 Close 00 Stop Lamp Off 00 00 00 2 Color Strobe Function This features allows two adjacent Color Gobo combinations on the Color Gobo wheel to strobe in and out of each other For example Looking at the chart above Gobo 1 is red and gobo 2 is blue Using the 2 Color Strobe function will allow red and blue strobe Another example is to take gobos 14 and 15 together gobo 14 is orange and gobo 15 is pink therefore using the 2 Color Strobe function will give off an orange and pink strobe This feature will work with any two color gobo combination that next to each other on the gobo wheel American DJ www americandj com XP 3 Instruction Manual Page 16 Gobo Wheel Layout GOBO 1 This chart details the gobo patterns as well as the gobo placement on the internal wheel Gobo one is the large spot The arrow indicates the wheel rotation American DJ www americandj com XP 3 Instruction Manual Page 17 XP 3 Fixture Cleaning Due to fog residue smoke and dust cleaning the internal and external optical lenses and mirror should be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates l e smoke fog residue dust dew In heavy club use we recommend cleaning on a monthly basis Periodic cleaning will ensure longevity and crisp output 1 Use normal glass cleaner and a soft cloth to wipe down the outside casing 2
21. r in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX and Master Slave Operation The XP 3 can be controlled via DMX 512 proto col The American DJe XP 3 is a five channel DMX unit The DMX address is set on the side panel using the three function buttons under the LCD Your unit and your DMX control ler require a standard 3 pin XLR connector for data input and data output Figure 1 If you are making your own cables be sure to use standard two conductor shielded cable This cable may be purchased at almost all pro sound and lighting stores Your cables should be made with a male and female XLR connector on either end of the cable Also remember that DMX cable must be daisy chained and can not be split American DJ www americandj com XP 3 Instruction Manual Page 5 Figure 1 XP 3 Set Up Notice Be sure to follow figure three when making your own cables Do not use the ground lug on the XLR connector Do not connect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s
22. the unit Never use a power when the ground prong has been removed or broken off The ground prong is used to reduce the risk of electrical shock in case of an electrical short 6 Fuse Holder This housing stores the 5 amp GMA protective fuse Always replace with the exact same type fuse unless other weanstudeddy an authorized American Due service technician 7 Lamp Socket Cover Thumb Screw This thumb screw holds the lamp socket assembly cover 16 into place 8 Lamp Socket Cover This thumb screw holds the lamp socket cover 16 into place American DJ www americandj com XP 3 Instruction Manual Page 10 XP 3 9 Audio Sensitivity Knob This knob adjust the audio sensitivity of the internal microphone 10 Turning the sensitivity knob in the clockwise direction will increase the sensitivity to sound Turning the knob in the counter clockwise direction will decrease the fixture s sensitivity to sound Controls and Functions 10 Microphone This microphone receives external low frequencies to trigger the unit in Sound Active and Master Slave mode 11 Cooling Vents These vents are used to allow proper cooling Keep the vents clean Never block the vents improper cooling may result in premature lamp failure 12 Option Switches These are used to access two special functions Switch 1 Inverted Pan When activated this switch will invert the PAN value Left will become right and vice versa
23. truction Manual Page 21 XP 3 Warranty 1 YEAR 365 DAYS LIMITED WARRANTY A American DJ hereby warrants to the original purchaser American DJ products to be free of manufacturing defects in material and workmanship for a period of 1 year 865 days from the date of purchase This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service send the product only to the American DJe factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty American DJe will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in its original package No accessories should be shipped with the product If any accessories are shipped with the product American DJe shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which American DJ concludes after inspection affects the reli ability of the product if the product has been repaired or serviced by anyone other than the American DJe f
24. y or fitness shall apply to this product after said period has expired The con sumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall American DJe be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product G This warranty is the only written warranty applicable to American DJ Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published H Lamps are not covered under this or any other warranty either written or implied American DJ www americandj com XP 3 Instruction Manual Page 22 Technical Specifications Model XP 3 Lamps ZB JCR H5 15v 150w 120v 60HZz or 220v 50 60HZ 12 5 H x 11 25 W x 8 5 D Multiple Colors 17 color gobo combinations w 3 bicolored combinations plus white spot 19 Lbs 5 Amp GMA None 5 Channels Yes Working Position Any Safe Secure Position Warranty 1 Year 365 days Voltage is preset at the factory and is not user selectable Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice American DJ American DJ Group of Companies World Headquarters 4295 Charter Street Los Angeles CA 90058 USA Tel 323 582 2650 Fax 323 582 2610 American DJe www americandj com
Download Pdf Manuals
Related Search