American DJ Light Copilot Microphone User Manual
Contents
1. eaei 4 nx 19 wx 4d Total Weight System re oe sosise esiri ne E EEA RERE EATE a EESE iSi 7lbs 3 5Kg American D Supplye Los Angeles Ca Light Copilot Page 32. American DJ User Instructions LIGHT COPILO T Introduction Congratulations and thank you for purchasing the A merican DJ Light Copilote The Light Copilot is an eight channel con troller with two separate chase zones Each zone is switchable from an audio or a timed chase sequence Chase intervals vary from 0 1 seconds to 10 minutes The controller has a built in microphone for easy audio chase sequences Chases can be made to run to sound via an internal microphone or and external RCA audio line input Audio chase sensitivity is adjustable by a rotary knob on the front panel A Latch switch can override the chase function to remain an individual channel on while the other maintain their chase sequence You can daisy chain up to three power packs per a controller for easy installation and enhanced flexibility The power pack uses high quality triacs for increased reliability This unique controller allows for a single power source i e the controller unit receives it s power from the relay pack via the 9 pin com cable Operating Instructions Set Up 1 Connect the supplied 9 pin com cable from the out put of the controller unit to the input of the power pack 2 Plugin the power pack to a standard AC outlet Note The controller unit does not come with an external power supply an external power supply is only needed if you are running two or three power packs 3 If desired plugin the Bar T Cue FS remote foot switch control usin
3. g the 1 4 stereo jack connection on the rear of the controller unit Bar T Cue FS switch may be purchased as a separate option Basic Operation 1 After you have completed the set up procedure be sure main power is off and connect your desired lighting effects to the power relay pack Note There are two sockets per a channel on the relay pack you can plug an effect into either socket or use both sockets to control two different lights to turn on at the same time 2 Once you have connect your desired effects to the relay pack you can use the the Latch buttons to turn the fixtures on and off or use the Flash Buttons to momentarily turn fixture on and off 3 The controller unit controls to separate 4 channel zones Each zone may be controlled independently of each other The zones may chased through a build in timer or through an audio source internal or external 4 To run the fixtures to the chase sequence Turn the on off Fig 10 switches to the on position for the fixture you want to include in the chase sequence Use the speed knobs Fig 3 in conjunction with the chase time switches Fig 7 to adjust the chase speed to your ideal settings See page 2 Chase Audio Selector 5 Torun the fixtures to audio Turn the on off Fig 10 switches to the on position for the fixture you want to chase to audio Use the audio knob Fig 2 to adjust the audio sensitivity to your ideal settings 6 During the chase sequence or audio
4. geles Ca Light Copilot Page 2 8 Full On Switches This switch is designed to be used with the optional Bar T Cue FS foot switch controller When in the ON position and used with the Bar T Cue FS foot switch controller the foot switch can turn all fixture on in a bank This switch has no function with out the Bar T Cue FS foot switch 9 Flash Buttons Use these button to momentarily turn the corresponding fixture on 10 Effect Switch Use these switches to link the corresponding channels the the chase settings a When in the ON position Top the corresponding fixture will be linked to chase modes b When in the OFF position Lower the corresponding channel will react only to the Latch Buttons Fig 4 and Flash Buttons Fig 9 11 Stand By Switch This switch will hold all output to all channels when depressed It s func tion is indicated by the Stand By Indicator Fig 6 12 Internal Microphone This picks an audio signal to run the audio chase 13 Control Output This connection is used to connect a 9 pin com cable from the controller to the relay pack Be sure to only use the LC 25 cable that comes with your unit this cable is especial ly designed to be used with your Light Copilot 14 DC Input Used to plug in an external power supply 9v 12v DC Typically not used under normal conditions 15 Audio Input Used in audio chase mode Use to connecting an external audio source directly to the u
5. mode you can use the Latch or Flash Buttons to manually override either the chase sequence or the audio mode and leave a fixture running 7 You may use the Stand By button to black out all controller functions and output American DJ Supplye Los Angeles Ca Light Copilot Page 1 Controls and Functions Controller Front Panel CH1 4 CH5 8 17 18 19 20 Relay Pack Side View AC 120 0Hz 15A OUTPUT CIRCUIT BREAKER AC POWER 1 Power Switch Applies main power to the unit 2 Audio Control This knob controls the audio sensitivity the unit will react to 3 Chase Speed Control Two sperate knobs to control independent chase speed for channels 1 4 and channels 5 8 4 Latch Buttons Pressing these buttons will maintain power to the fixture connected to the corresponding channel 5 Channel Indicators These LED s will glow indicating channel activity 6 Stand By Indicator This LED will glow indicating controller is in Stand By mode 7 Chase Audio Selector These 3 position switches control the chase modes for channels 1 4 Bank 1 and channels 5 8 Bank 2 The two banks can be controllers independently a When the switch is in the 10MIN position Up the chase speed will react more slowly b When the switch is in the x 1 position Center the chase speed will react more quickly c When the switch is in the Audio position Lower the chase will react to audio sensitivity American D Supplye Los An
6. nit This will provide a more accurate audio source when the internal mic is not sensitive enough or when the unit is mounted far away from an audio source speaker 16 Foot Control Input This connection is used to connect a Bar T Cue FS foot switch controller to the unit via a 1 4 stereo jack 17 Signal Output This 9 pin com connection is used to connect another LC 8SP relay pack to the controller unit Be sure to use only specified American DJ 9 pin com cables 18 Signal Input Used to link the controller unit with LC 8SP relay pack via a specified 9 pin com cable 19 Circuit Breaker A built in 15A circuit breaker designed to protect wiring under heavy or over loaded conditions 20 Power Input AC 1220v 60Hz 15A This will also power the controller unit through the 9 pin com cable Packing List 1 1 LC 100 controller 2 1 LC 8SP Switch pack 3 1 LC 25 25 foot 9 pin com extension cable Specifications Power Input LC 100 nen netic nica kek ed desieeess ees eden DC 9 12v 200mA min Power Input LO 8SP ecese neiaa an Eanna eaan clita costa Uosatash NASE NENEKA E AC 120v 60Hz 15A Channel Output aneian a a i r a 10A per channel Total 15A max Circuit Breakers cscsccccs ccseslesdcckccucedtacneseaececscvegeesledeecdeaed sstuedevacccen EEEE EEE E E aKa 15A EC 100 DIMENSIONS eee o e eea E E EE aE E G 13 16 h x 19 wx 2 7 16 d LC 8SP DIMENSIONS 5 55 5 sisi seccessseessceeess vovssveveSee T AEE EEA E RE
Download Pdf Manuals
Related Search