Amcor AL-10 Air Conditioner User Manual
Contents
1. you keep them a safe place 4 for future reference 14 Troubleshooting Problem Cause Solution Never try to repair or dismantle the air conditioner yourself Tampering with the unit may result in the loss of warranty and can endanger the user and property The Air Conditioner Does Not Function Properly Windows or doors are open Close doors and windows The filter is dirty Clean or replace filter Air inlet or air outlet is blocked Remove blockage Room temperature lower than the selected value Lower temperature selected The overheat protection is activated Wait 3 minutes until temperature has decreased then turn on again The Unit Does Nothing No power supply Make sure outlet works Be sure Green Light is on L C D I Plug Press Re start button Water container is full Drain the Unit Timer Function Set Deactivate the Timer Function The Unit is Noisy Unit is not standing on a level surface Place on an even surface The Remote Control Does Not Function Distance too great Make sure the remote is aimed at the control panel Remote control signal not detected by control panel Control is aimed at the control panel Batteries are dead Replace the batteries If you have any questions regarding the operation of the AL 10 000 please contact AMCOR at 1 866 361 2233 REPLACEMENT FILTERS2. I Storing the Power GONG 11 TROUBLESHOO TIN Gi 12 WARRAN D 14 During the process of cooling some water will be extracted from the air into the unit Most of this water is used to cool the unit and make it run more efficiently This is a feature not found in most Portable Air Conditioners If the unit is operated in VERY HUMID air water will collect in the container inside the unit Model Number AL 10 000EH Model N AL 10 000E If the Internal Water Container is full the backlight on the LCD display will flash the unit will shut off and OCEANO iia sina it must be drained before it will re start Cooling Capacity 10 000 BTU hr 10 000 BTU hr seus tn these Shas ioe Capa Use a Shallow Container Dish ae Power Consumption 660W 6 0 660W 6 0 l 2 Remove the drain knob amp rubber plug from Repeat steps 2 3 amp 4 until all the condensed water Once all the condensed water has been removed Turn off the unit Humidity Removal Capacity 38 Pts Day 38 Pts Day Position a flat container or dish under the drain hole Do not allow the water to drip continuously into a Recommended room size Up to 300 sq ft Up to 300 sq ft the container as it might easily overflow Power Supply 15 60Hz Phase 15 60Hz Phase the drain hole The condensed water will drain out automa
3. To purchase Replacement Filters for this unit contact AMCOR at 1 866 361 2233 and request model number AL 10 000F If this product is defective or not working properly please DO NOT return to your retail store Please contact us directly for any Service or Technical Assistance at 1 866 361 2233 Amcor Inc www amcorgroupusa com 12 Table of Contents THANK 2 2 SPEC 3 centr err 4 PART ae ee re err ene tr th 9 EE 5 5 6 E 6 Wall COMME CHONG EEEE narnia pial Nema 6 Mo nt ng Me EXNGUSE TIDE 7 Cleaning the Filter OPERA OWN 8 Control PONE ces 8 Setting Mode 8 Auto TGS 8 Setting the 8 Setting FaN 9 9 Regulating Airflow Direction 9 DRAINAGE E 10 How the Unit 10 Cleaning the lII Cleaning 11 PNG of e aeaieie Ea Eae EARLE E Ea r a
4. and set your desired temperature as the Auto mode has a preset temperature please see below that cannot be changed The indicators of the functions in progress come on at the same time e g Cool and Lo Cooling mode with Low fan speed Auto Mode When this mode is selected the unit is preset to the following temperature settings and unit will only start to e Cool when room temperature is higher than 75 F e Heat when room temperature is lower than 68 F AL 10 000EH only If room temperature is between 68 F and 75 F unit will stay in Fan mode Again when in Auto Mode the temperature settings cannot be changed Setting the Temperature in Cooling or Heating Mode The display window s default is to display the ambient room temperature The green indicator light under RT is RT Room Temperature To set your desired temperature press the Temperature up or down buttons ranging from 62 F to 90 F Each press will increase or decrease your set temperature by 1 When pressing the temperature up or down buttons the window will change to display your set temperature At this time the green indicator will light under ST Set Temperature Once the temperature up or down buttons is released the window will return to displaying the ambient temperature after a second Note When unit is in the following modes Auto Cool or Heat the compressor will cool heat the room to reach the set temperature Once the ambient temperature h
5. 2 2006 NWAMCOR UltraClean One Year Limited Warranty NX Amcor Inc Amcor warrants the original retail purchaser Purchaser purchasing the free of charge all defective parts for a period of 1 year from date of original purchase IMPLIED WARRANTY OF MERCHANTABILITY OR OTHERWISE MAY BE COMMENCED Al Nn d l t Nn been 1 subject to misuse or neglect 2 damaged an accident 3 used for a purpose for For models AL 0 000 and AL 0 000 United States that the Amcor product with which this warranty is enclosed is free from defects in materials and workmanship Amcor s sole obligation under this warranty is to replace or at Amcor s discretion to repair gt O R l A B l ANY IMPLIED WARRANTY OF MERCHANTABILITY IS SIMILARLY LIMITED TO ONE 1 YEAR FROM DATE OF ORIGINAL PURCHASE AND NO ACTION BASED UPON ANY AFTER EXPIRATION OF ONE 1 YEAR FROM DATE OF ORIGINAL RETAIL PURCHASE Some states do not allow limitations on how long an implied warranty lasts so the above limitation 9 M whners Manua The provisions of this warranty shall not apply to any product which in Amcor s judgment has which it was not designed or 4 repaired or altered in any way that adversely affected its performance or reliability To obtain warranty service the defective product or part must be shipped or delivered to Amcor s authorized service center All postage insurance a
6. age of the water container is required before moving the unit or putting it into storage If the electric socket is different from the plug provided have a professionally qualified electrician replace the outlet with a suitable one Avoid the use of adaptor plugs multiple sockets and or extension cords if their use is necessary ensure that they conform to the current safety regulations Do not pull the power cord or place it near a source of heat always unroll it completely to avoid the possibility of dangerous overheating If the power cord is damaged it must be replaced qualified person THE MANUFACTURER DISCLAIMS ANY RESPONSIBILITY IF THE ABOVE INSTRUCTIONS ARE NOT FOLLOWED Setting The Fan Speed Press the SPEED button to choose the fan speed you require high or low The indicator of high or low fan will light up at the same time If the unit is in AUTO mode it will select the fan speed automatically according to the ambient temperature the related indicators cool fan or heat will light up at this time the fan speed switch is invalid Setting the Timer Press the TIMER button to set the operating hours you desire 1 to 12 hours the timer indicator will light up When the set time has elapsed the machine will turn off automatically The display window will show the hour s you set as you press the TIMER button the timer button is not pressed the unit will work continuously By pressing th
7. as reached the set temperature the compressor will stop and unit will run in Fan mode To conserve energy the compressor will not start immediately after a couple degrees increase or decrease but will wait for a 5 F allowance For example In Cooling Mode with a set temperature of 70 F When compressor first stops after reaching 70 F unit will auto switch to Fan Compressor will start cooling again when ambient temperature increases to 75 F or above In Heating Mode with a set temperature of 72 F When compressor first stops after reaching 72 F unit will auto switch to Fan Compressor will start heating again when ambient temperature drops to 67 F or below In Auto Mode with preset temperature of 68 F for heat and 75 F for cool Compressor will start cooling again when ambient temperature reaches above 80 F or will start heating when ambient temperature drops below 63 F I Control Panel 2 Cooling Air Outlet 3 Handle 4 Castors Accessories 10 12 13 14 I5 Adaptor for insertion over the hose and into the back of the air conditioner Exhaust Hose Adjustable Slide Bar Round Connector Cap for Round Connector Remote Control Electronic control models only oNN Air Filter Air Inlet Exhaust Air Outlet Cord Hanger Water Stopper Rubber Plug Inside Installation Installation Mounting the Exhaust Pipe e The supplied Exhaust Hose can be extend
8. e timer button but without turning on the unit you can PRE SET the time for the machine to work For example if you press the timer to 2 the unit will come on automatically after 2 hours 2 All the above functions can also be performed with the supplied remote control This remote control requires 2 AAA batteries to operate Regulating the Airflow Direction _ Move the air vent directly to adjust the airflow direction from the horizontal louvers 7 Turn the roller the air vent to control the airflow direction from the vertical louvers IMPORTANT e The compressor will start approximately 3 minutes after the unit is turned on this will help prolong the life of the compressor After switching the unit off please wait at least 3 minutes before turning the unit back on e The cooling system will switch off if the room temperature is lower than set The fan however keeps working at the set level If the ambient temperature rises above the chosen temperature 5 F the cooling will resume In heating mode the compressor will switch off if the room temperature is HIGHER than the one set the fan keeps working at the set level When the room temperature drops 5 F below the chosen temperature heating will resume e This machine is equipped with an ANTI FROST function Sometimes while using the heating function during low temperatures the heating will stop for a while to melt the i
9. ed from foot to 5 feet for mounting It is recommended that you use the shortest possible length of Hose e Take care to prevent any kink or bend in the middle of the Exhaust Hose as this will trap hot exhaust air which will radiate back into the room Window Kit Installation In order for this unit to function 2 Attach Slide Bar Connector 3 Place Adjustable Slide Bar in properly it must be vented to the Round Connector to the the window and expand so it outside other end of the Hose by fits tightly Fitting the Exhaust Hose through extending hose at least 6 4 Lower the window the window is easy Please see Then tighten Hose by turning Make sure the Hose has below the Round Connector ae Knee clockwise Extend Hose at least 6 and Slide Bar has 3 sections which insert it into back of the unit allows installation in windows up tightening into place by turning to 48 in width it clockwise WARNING The length of the Exhaust Pipe is specially designed according to the specification of this product Round Connector Do not replace or extend it with your own hose as this could cause the unit to malfunction Cleaning the Filter Use a vacuum cleaner or tap the filter lightly to remove loose dust and dirt from the filters Wall Connection and then rinse them thoroughly under running water no hotter than 104 F Make a hole 5 1 in diameter 3 Extend end of the Exhaust 5 P
10. mp cloth to wipe the body clean Never use strong chemicals oil based products detergents chemically treated cloths or other cleaning solutions These could possibly damage the cabinet Cleaning the Filter Use a vacuum cleaner or tap the filter lightly to remove loose dust and dirt from the filters and then rinse them thoroughly under running water no hotter than 104 F Dry thoroughly before replacing Do not wet the activated carbon filter remove from frame before rinsing IMPORTANT Never operate the unit without the filters End of Season Storage Unplug the unit Drain the condensed water COMPLETELY please refer to page 10 Clean or change the filter On a warm day turn the unit to fan mode for a couple of hours so that the inside can dry out completely It is recommended that the unit be put back into its original carton for storage Do not stack heavy objects on top of the unit Storing The Power Cord When the unit is not in use please store the power cord away as shown
11. nd shipping charges are the responsibility of the Purchaser and are not included in this warranty AMCOR NEITHER ASSUMES NOR AUTHORIZES ANY PERSON ASSUME FOR IT ANY sae aS Se re OTHER LIABILITY IN CONNECTION WITH ITS PRODUCTS THERE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF NO RESPONSIBILITY IS ASSUMED FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES THAT MAY RESULT FROM Se THE USE OF AN AMCOR PRODUCT NOR FOR THE DAMAGES DUE TO ACCIDENT ABUSE LACK OF RESPONSIBLE CARE THE AFFIXING OF ANY UNAUTHORIZED ATTACHMENT LOSS OF PARTS OR USE AT AVOLTAGE OTHER THAN SPECIFIED Some states do not allow the exclusion of limitation of incidental or consequential damages so these limitations may not apply to you Amcor disclaims all liabilities for defects or damages caused by use of replacement parts obtained _ from or by service at any service center other than Amcor s authorized service center amcon This warranty gives you specific legal rights and you may also have other rights which vary from state to state Product AMCOR Portable Air Conditioner Model AL 10 000E EH Date Purchased Production Code QUESTIONS Call 866 361 2233 www amcorgroupusa com gt It is important that you read these instructions before using your new purchase and Dear Customer Please keep this warranty for your record DO NOT return it we strongly recommend that ey
12. nternal frost When this occurs wait for heating to resume e As you switch on the heating the fan will stop for 15 20 seconds prior to the unit starting 9 Thank You Thank you for choosing the portable air conditioner from AMCOR a leading brand in indoor air treatment We would like you to enjoy the many benefits this unit offers so please read this manual carefully and take full advantage of the many advanced features that your AMCOR Air Conditioner offers you AMCOR has specialized in complete indoor environment control manufacturing world class air conditioners dehumidifiers and air purifiers with innovative technology In designing these advanced products we have listened carefully to our customers and have passed their views on to our research and development laboratories We wish you many years of enjoyable use After reading this manual please keep it in a safe place for future reference Energy Saving Tips e Do not locate the air conditioner where furniture or other objects can obstruct the airflow e Keep doors closed so cool air does not escape e Keep the filters clean Set the unit to maximum cooling and high speed fan initially then adjust the unit to a comfortable setting NOTE Use the Temperature Control UP DOWN to adjust Air Conditioner cooling to a desired level Maintenance Always unplug the unit from the wall outlet before beginning the cleaning Cleaning the Housing Use a soft da
13. tically A When the container is almost full replace the 2 2 rubber plug into the drain hole to stop the water Fan Speed Empty the container drain knob Timer 12 hours 12 hours is emptied Temperature Set Range 62 F 90 F 62 F 90 F replace the rubber plug into the drain hole firmly ee aes The Full Water indicator should be off now 2 LO rubber plug I5 W x 16 D x 30 H I5 W x 16 D x 30 H N Replace the drain knob drain knob Working Temperature Cooling 62 F to 110 Cooling 62 F to 110 Turn unit the unit will resume working Heating 41 F to 81 F REMARKS The cooling capacity of the unit may be affected by the height of the ceiling quality of insulation number of windows etc Operation Automatic Mode Indicator Cooling Mode Indicator High Fan Speed Indicator Fan Mode Indicator Low Fan Speed Indicator Heating Mode Indicator For Models With Heating Options Room Temperature Indicator Timer Operation Indicator Set Temperature Indicator Temperature Down Selector On Off Power Selector Mode Function Timer Selector Fan Speed Selector Option Selector Setting Mode Function Press the MODE button to select the required working mode Automatic Cooling Fan or Heating Heating is only available for AL 10 000EH The green indicator illustrating your selected mode lights up It is recommended to select Cooling or Heating mode
14. ush Adaptor to fit firmly Dry thoroughly before replacing in the wall Pipe part 11 and screw into over the opening on the back Notice Never operate the unit without the filters the Round Connector by of the unit 2 Insert the Round Connector turning clockwise part 13 into the hole 5 When not in use cover the hold in place by using 4 small 4 Extend other end of exhaust Round Connector and hole screws not supplied pipe and screw in Adaptor part with Cap part 14 10 by turning clockwise Important e Leave the unit in an upright position for at least 2 hours before use e Always place the unit on an even surface e The power cord has built in L C D I Leakage Current Detection Interruption circuit breaker for added safety If the power supply is interrupted please press the reset button to reconnect the unit to the power source The green light should be on e Make sure the unit is connected to a correctly grounded power supply For proper operation the unit must be vented to the outside e Do not cover or obstruct the appliance inlet or outlet grilles e To avoid the risk of shock the product should never be used in bathrooms shower rooms or in any other steamy or wet areas e Always transport the unit in an upright position e Do not sit or stand on the unit e Do not place objects on the unit Do not touch the unit with wet damp hands or when standing barefoot e Drain
Download Pdf Manuals
Related Search