Allstar Products Group MVP-831E Satellite Radio User Manual
Contents
1. J TROUBLESHOOTING NOTES If you experience problems with the MVP 831E Receiver try some of the suggestions listed below before calling the Factory Technicians MVP 831E COMMERCIAL Allst 7 RECEIVER INSTRUCTIONS Ee READ THIS MANUAL CAREFULLY BEFORE BEGINNING INSTALLATION External interference such as radio towers Change to a different frequency Stuck transmitter in building Change code switches from factory settings RECEIVER APPRARS DEAD THERE IS NO Check battery in transmitter RESPONSE WHEN TRANSMITTER BUTTONS ARE PUSHED Check the power connections to the receiver There must be at least 20 VAC at the receiver power connections If a 24V system Review the code switch and the selector switch settings then reprogram the receiver Try a different code switch setting Check the antenna installation Wait one minute for the receiver to warm up Check battery in transmitter ONE RECEIVER WORKS BUT THE OTHER IS DEAD Relocate the antennas Receivers too close together cross talking move to different locations Check code switch settings INSTALLER Leave this manual with your customer upon completion of the installation Jk PRODUCT FEATURES Allstar MVP 831E Commercial Receivers are designed to work with most commercial door operators Programming the receiver to accept the transmitter signal is a matter of pushing the LEARN button on the receiver body and activating the transmitter The MVP 82. and necessary maintenance labor charges for dismantling or reinstalling a repaired or replaced unit or replacement batteries These warranties are in lieu of all other warranties either expressed or implied All implied warranties of merchantability and or fitness for a particular purpose are hereby disclaimed and excluded Under no circumstances shall Allstar be liable for consequential incidental or special damages arising in connection with the use or inability to use this product In no event shall Allstar s liability for breach of warranty breach of contract negligence or strict liability exceed the cost of the product covered hereby No person is authorized to assume for Allstar any other liability in connection with the sale of this product This warranty gives you specific legal rights You may also have other rights which vary from state to state Warranty effective after March 1 2004 For Information Phone 610 873 6900 World Wide Web info allstarcorp com 4 Page 4 of 4 DOC 112049 REVA IMPORTANT INSTALLATION NO ES A TO REDUCE THE RISK OF SEVERE INJURY OR DEATH WARNING READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS ALLSTAR MVP 831E RECEIVERS ARE INTENDED FOR USE WITH COMMERCIAL DOOR OPERATORS ONLY DO NOT USE FOR ANY OTHER PURPOSE DO NOT MODIFY IN ANY MANNER CHECK LOCAL BUILDING AND ELECTRICAL CODES FOR MANDATORY INSTALLATION AND WIRING REQUIREMENTS CONNECT POWER CORDS ONLY TO A PROPE
3. ao zZ gt o 1 2 oNEORANGE OPEN W ONE BLACK CLOSE STOF ONE GRAY STOP Figure 2 panel 5 Connect the remaining MVP 831E orange wire to the OPEN pushbutton terminal in the door operator control panel MOvid the 3 button 106548 Figure 1 In the door operator control panel locate the wire door operator to wire just removed from the pushbutton COMMON 3 Connect the following wires from the MVP 831E to the operator 3 button COMMON as shown in Figure 3 4 Connect the remaining MVP 831E black wire to the CLOSE pushbutton terminal in the door operator control 6 Finish the wiring by connecting 24 VAC to the red and white wires of the MVP 831E receiver BEFORE APPLYING POWER CHECK ALL CONNECTIONS AND INSTALL THE ANTENNA Page 2 of 4 DOC 112049 REVA station 106549 Step5 o qaei WALL PUSH Step3 BUTTON S COMMERCIAL STATION OPERATOR OPEN MVP 831E ae TE RECEIVER SON OPEN f CLOSE Step 4 NY er COMMON cance TI o 1 Pe T BLACK GRAY BLACK GRAY BERA Figure 3 ORANGE E Removed Wire plz See Step 1 Step 6 24 VAC ee RECEIVER PROGRAMMING INSTRUCTIONS Learning Transmitter Codes The MVP 831E receiver is capable of learning the codes from up to 8 different Allstar Open Close Stop transmitters The transmitters may be any combination of Allstar s MVP Classic or ori
4. blocked or shielded such as a car traveling through a tunnel the distance will decrease Always change the Factory set codes a Manufacturer s Limited Warranty Allstar warrants its radio controls to be free from defect in material and workmanship for a period of one 1 year from the date of purchase To obtain service contact your dealer To obtain service under this warranty the buyer must obtain authorization instructions for the return of any goods from Allstar before returning the goods The goods must be returned with complete identification with copy of proof of purchase freight prepaid and in accordance with Allstar s instructions or they will not be accepted In no event will Allstar be responsible for goods returned without proper authorization or identification Goods returned to Allstar for warranty repair within the warranty period which upon receipt by Allstar are confirmed to be defective and covered by this limited warranty will be repaired or replaced at Allstar s sole option at no cost and returned pre paid Defective parts will be repaired or replaced with new or factory rebuilt parts at Allstar s sole option This limited warranty does not cover non defect damage damage caused by unreasonable use damage caused by improper installation or care vandalism or lightning fire or excessive heat flood or other acts of God including but not limited to misuse abuse or alterations failure to provide reasonable
5. 31E is connected to the commercial operator in the same manner as a 3 button station and provides full open close and stop functionality via radio control The receiver is powered from the operator s 24 VAC transformer The antenna is removable and may be relocated using coaxial cable not included for better RF reception SOME THINGS TO REMEMBER Range is dependent on the installation type of building type of door and the location of the transmitter When these conditions change so will the distance RECEIVER CLICKS WHEN ANY TRANSMITTER Any transmitter can interfere with operation These BUTTON IS PUSHED BUT NOTHING ELSE HAPPENS Check the wire amp connections in the STOP circuit Refer to Figure 3 Check the OPEN amp CLOSE connections The wire gage may be too small for the number of wall stations used Check the power to the door operator Check the door operator s control voltage SHORT DISTANCE OR INTERMITTENT OPERATION Relocate the antenna with a coaxial cable Metal objects too close to receiver move to a better location Allst 7 include cell phones cordless phones wireless systems and CB and mobile transmitters Other sources of interference include computer equipment industrial equipment electric motors fluorescent lights etc The list is endless Do not lengthen or shorten the receiver antenna It is set to an optimal length based on the frequency of operation If the antenna is
6. HE MANUFACTURER OF YOUR OPERATOR FOR MORE DETAILS Page 1 of 4 DOC 112049 REV A X MVP 831E RECEIVER WIRING INSTRUCTIONS IMPROPER WIRING COULD CAUSE ELECTROCUTION OR DAMAGE TO CIRCUITRY FOLLOW LOCAL BUILDING AND ELECTRICAL CODES TO PREVENT ELECTROCUTION DISCONNECT POWER AT FUSE BOX AND DOOR OPENER BEFORE WIRING PERMANENTLY The MVP 831E receiver functions as a 3 button station Three sets of isolated contacts are provided normally open contacts for the OPEN PUSHBUTTON orange wires normally open contacts for the CLOSE PUSHBUTTON black wires normally closed contacts for the STOP PUSHBUTTON gray wires Refer to Figure 1 For special STOP circuit applications normally open contacts are available from the factory Typical 4 wire 3 button stations are wired as shown in Figure 2 Number 18 gauge wire or heavier must be used for wiring the control stations and the MVP 831E receiver to the door operator Smaller gauge wire may cause operational problems especially when multiple 3 button stations are used For typical installations the MVP 831E receiver is mounted near the door operator away from any high voltage conduits or steel support beams For wiring follow the steps below and refer to Figure 3 OPEN WALL PUSHBUTTON STATION 1 105113 connecting the COMMON Note its location and remove OPEN 2 Connect one of the gray wires from the MVP 831E to the a gt S T EE CLOSE a T w g oe eee
7. RLY GROUNDED OUTLET IF PERMANENT WIRING IS REQUIRED BY CODES DISCONNECT POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE ATTEMPTING ANY WIRING CONNECTIONS DO NOT WEAR RINGS WATCHES OR LOOSE CLOTHING WHILE INSTALLING OR SERVICING GARAGE DOOR OPENERS WEAR SAFETY GOGGLES OR OTHER PROTECTIVE EYEWEAR AN UNBALANCED DOOR OR ONE THAT STICKS OR BINDS MAY CAUSE INJURY OR DEATH ENSURE DOOR IS PROPERLY BALANCED AND ELIMINATE ANY STICKING OR BINDING YOUR GARAGE DOOR IS A LARGE MOVING OBJECT THE SPRINGS PULLEYS CABLES AND MOUNTING HARDWARE UTILIZED TO BALANCE ITS OPERATION ARE UNDER EXTREME TENSION AT ALL TIMES AND CAN CAUSE SERIOUS PERSONAL INJURY EVEN DEATH IF DISTURBED ONLY A QUALIFIED SERVICE PERSON SHOULD MOVE LOOSEN OR ADJUST DOOR SPRINGS OR HARDWARE LOCATE CONTROL PUSHBUTTONS WITHIN SIGHT OF THE DOOR AND AWAY FROM THE MOVING PARTS OF THE DOOR INSTALL ENTRAPMENT WARNING LABEL NEXT TO THE CONTROL PUSHBUTTON IN A PROMINENT LOCATION REMOVE ALL ROPES AND REMOVE OR MAKE INOPERATIVE ALL LOCKS CONNECTED TO THE GARAGE DOOR THE IMPORTANT SAFEGUARDS AND INSTRUCTIONS IN THIS MANUAL CANNOT COVER ALL POSSIBLE CONDITIONS AND SITUATIONS IT MUST BE UNDERSTOOD THAT COMMON SENSE AND CAUTION MUST BE EXERCISED BY THE PERSON S INSTALLING MAINTAINING AND OPERATING THIS EQUIPMENT T DO NOT USE RADIO CONTROLS ON COMMERCIAL DOOR OPERATORS UNLESS PROPER ENTRAPMENT PROTECTION WARNING DEVICES ARE INSTALLED CONSULT T
8. ginal dip switch type Open Close Stop transmitters Models 8833 O C S 8833C O C S 831 733 639 and or 53S Match the receiver operating frequency with the transmitter operating frequency Pre program the transmitter or set the DIP switches according to the instructions that accompanied the transmitter For transmitters that can operate multiple doors Models 8833C O C S 733 639 and 53S make sure the selector switch es is are positioned for the desired door you want to operate before starting the receiver programming steps below Programming The Receiver Step 1 Momentarily press and release the Learn button The LED will turn on Step 2 Using a programmed transmitter press any one of the transmitter buttons OPEN CLOSE or STOP When the receiver learns the transmitter code the LED will turn off The receiver has automatically learned the two remaining buttons Step 3 Repeat to add additional transmitters with different codes if desired Page 3 of 4 Learn Erase Button Lip Ll oS Indicator LED Erasing the Receiver s Memory Step 1 Press and HOLD the Learn button The indicator LED will turn on Step 2 When the LED turns off after approximately 5 seconds release the Learn button A Important Refer to individual manuals for transmitter installation coding and user instructions DOC 112049 REV A
Download Pdf Manuals
Related Search