Home

Alliance Laundry Systems FLW1526C Speaker System User Manual

image

Contents

1. FLW1979N 1 Standpipe 2 in 5 08 cm or 1 1 2 in 4 cm Figure 8 12 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Step 5 Gravity Drain Models Only Connect Drain Outlet to Drain System Remove drain fitting four inches long and hose clamp from accessories bag Insert drain fitting into drain outlet hose Clamp hose and fitting Connect the drain fitting to a vented drain system using a flexible connection obtain locally Inside diameter of fitting is 1 53 in 3 89 cm and outside diameter is 1 66 in 4 22 cm The drain system must be vented to prevent an air lock or siphoning IMPORTANT Increasing the drain hose length installing elbows or causing bends will decrease drain flow rates and increase drain times impairing machine performance FLW1980N 1 Drain Trough 2 Drain Outlet Hose Figure 9 802734 Step 6 Remove the Shock Sleeves and Shipping Brace Remove front access panel by removing the two screws at the bottom of the panel Remove the five bolts and lockwashers from shipping brace with 9 16 in wrench and remove brace Refer to Figure 10 One is holding the brace to the weight Remove this bolt first Four bolts are located on the washer base Remove the two front bolts next and then the two rear bolts Remove all four shock sleeves by pulling o
2. FLW2127N FLW2128N Figure 18 When washing bulky items such as blankets and comforters use the DELICATE cycle The cycle includes agitation and final spin speeds that maintain the load s balance and minimize wear to the articles Figure 19 18 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 802734 Operation Step 3 Add Laundry Supplies Step 4 Set Fabric Selector Open dispenser drawer Measure and add low sudsing Set regular loads aa NORMAL or PERM PRESS Set high efficiency HE detergent 1 bleach 2 and delicate loads at DELICATE fabric softener 3 to the dispenser drawer refer to Figure 20 Close dispenser drawer PERM PRESS IMPORTANT If using non HE detergent avoid oversudsing by using 1 2 of the detergent manufacturer s recommended amount INORMAL DELICATE A canon FABRIC SELECTOR H1711 Dispenser drawer requires a special tool for removal Contact a service person if removal is necessary Step 5 Set WASH RINSE Temperatures W236 Figure 21 Set at HOT COLD rinse WARM COLD rinse or COLD COLD rinse NOTE Always follow manufacturer s care labels HOT COLD WASH TEMPERATURE H1701 Figure 22 Step 6 Insert Money Place coin s in slide and carefully push in as far as possible and then pull slide out as far as possible After IN USE light comes on indicating start of cy
3. 83 Y Y 28 in 71 1 cm 4 1 in 10 41cm I 40 67cm 1 5 in 1 3 8 cm 26 875 in 68 3 cm MODELS WITH GRAVITY DRAIN FLW2202N 1 1 5 in 3 81 cm Inside Diameter 1 86 in 4 72 cm Outside Diameter 6 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 802734 Before You Start Tools For most installations the basic tools you will need are ah ond D074I Wrench Screwdriver Pliers Socket Wrench Level 802734 Figure 1 Installation NOTE If the washer is delivered on a cold day below freezing or is stored in an unheated room or area during the cold months do not attempt to operate it until the washer has had a chance to warm up NOTE Install dryer before washer This allows room for attaching exhaust duct NOTE Some moisture in the wash drum is normal Water is used during testing at the manufacturer Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 7 Installation Installing the Washer Step 1 Position Washer Near Installation Area Move washer so that it is within 4 feet 1 2 meters of the desired area of installation NOTE For best performance and to minimize vibration or movement install washer on a solid sturdy and level floor Some floors may need to be reinforced especially on a second floor or over a basement Do not i
4. DO NOT COPY or TRANSMIT Rapid Advance The Rapid Advance feature allows the owner to quickly advance through an active cycle to a specific cycle step To enter Rapid Advance open the service door long enough for the IN USE light to turn on and close the door Refer to Figure 23 NOTE If service door remains open rapid advance cycles can be used for a free vend Press the PUSH TO START button to start the cycle Press PUSH TO START button again to advance through each cycle step Refer to Table 1 for cycle steps Cycle Steps Wash Fill Agitate cycle step Wash Distribute cycle step Wash Pulse Spin cycle step Rinse Fill Agitate cycle step Rinse Distribute cycle step Rinse Pulse Spin cycle step Extra Rinse Fill Agitate cycle step If extra rinse is enabled Extra Rinse Distribute cycle step If extra rinse is enabled Extra Rinse Pulse Spin cycle step If extra rinse is enabled Final Fill Agitate cycle step Final Distribute cycle step Final Pulse Spin cycle step Final High Spin cycle step Final Spin light on Breakaway cycle step Final Spin light on End of cycle door will remain locked for about 1 minute Table 1 802734 Operation Instructions for MDC Washers IMPORTANT Prior to first wash use an all purpose cleaner or a detergent and water solution and a damp cloth to remove shipping dust from inside of washtub IMPORT
5. Ke ER H Installing the Washer ioiii ia neis 8 Step 1 Position Washer Near Installation Area 8 Step 2 Position and Level the Washer sese 8 Step 3 Connect Fill Hoses se esseeseseessesesseessessesne 9 Step 4 Non Gravity Drain Models Only Connect Drain Hose to Drain Receptacle sss 11 Step 5 Gravity Drain Models Only Connect Drain Outlet to Drain System 12 Step 6 Remove the Shock Sleeves and Shipping Brace 13 Step 7 Wipe Out Inside of Wash Drum see 13 Step 8 Plug In the Washer sss 14 Step 9 Check Installation essen 15 ER ees 16 Meter Case n coe dae itcr dati p dente edd rts 16 Slide tegt ederet HER UE Se ne a E CREE TERR 16 Models Prepped for Card Reader 17 Operation cc ede n ode eb td ire ie 18 Operation Instructions for Coin Slide Operated Washers 18 Step 1 Load Laundry aner eee e ene 18 Step 2 Close Loading Door essen 18 Step 3 Add Laundry Supplies 19 Step 4 Set Fabric Selector sss 19 Step 5 Set WASH RINSE Temperatures sesesseseesoeeeeseeeeese0seeee 19 Step 62 Insert Money eegnen Ee 19 Indicator Lights essere nennen 20 Rapid Advance eee eee eter ree eruere 20 Operation Instructions for MDC Wasberg 21 Step 1 Load Laundry sese 21 Step 2 Close Loading Door essen 21 Step 3 Add Laundry Supplies
6. 22 Step 4 Set Fabric Selector and Wash Temperature 22 Step 5 Insert Coin s or Card sssssssssssseeee 23 Step 6 Start Washers 25 o ee ee E 23 Indicator Lughts sess eene 24 Operation Instructions for NetMaster Wasberg 25 Step 1 Load Landry echte tee pete dai aida 25 Step 2 Close Loading Door 25 Step 3 Add Laundry Supplies 25 Step 4 Set Fabric Selector esses 26 Step 5 Set Wash Temperature 26 Step 6 Insert Coin s or Card sssssssssssseeee 26 O Copyright 2010 Alliance Laundry Systems LLC All rights reserved No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher 2 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 802734 802734 Step 7 Start Washer sss Indicator Lights essere Maintenance uses tcd HO dign User Maintenance Instructions sssesssseesssessseeesseeees Cold Weather Care Care of Your Washer sse Cleaning Glass Sealing Area sss Replacing Hoses sse Filter COS et Eege Vacations and Extended Non Use Reinstallation of Shipping Materials Cleaning Foreign Object Trap sess Troubleshooting oooooooonnnccnnononioncnoncccononononccnnncconnnn n Contact Information Installer Checker Copyright Alliance Laun
7. REMOVE CARD LED is lit adhi INSERT CARD HERE M343I Figure 37 26 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 802734 Step 7 Start Washer After vend price has been satisfied push the START pad DOOR MUST BE CLOSED TO START WASHER H2071 Figure 38 Indicator Lights WASH WASH is lit at the beginning of a wash cycle and will remain lit until the wash cycle is complete RINSE RINSE is lit at the beginning of the RINSE or EXTRA RINSE cycle and will remain lit until the rinse cycle is complete SPIN SPIN is lit for all spin cycles DOOR LOCKED DOOR LOCKED is lit whenever the door is locked The door cannot be opened when this light is on 802734 Operation INSERT COIN CARD INSERT COIN CARD is lit to prompt the user to insert coins or card to satisfy the vend price When INSERT COIN CARD is lit the digits and decimal point show the vend price remaining to be satisfied REMOVE CARD Card Models Only REMOVE CARD flashes after the START pad has been pressed and the vend has been deducted from the card IMPORTANT If washer fails to operate properly after installation make sure electrical service and water supply faucets are turned on Are all the controls properly set Have a qualified service person refer to the wiring diagram located inside of washer control hood and check for broken loose or incorrect wiring NOTE Once a cycl
8. the installation Order hoses as follows No 20617 Fill Hose 8 feet 2 44 m No 20618 Fill Hose 10 feet 3 05 m 10 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 802734 Risers Risers or air cushions may have to be installed if the pipes knock or pound when flow of water stops The risers are more efficient when installed as close as possible to the water supply faucets refer to Figure 6 woos 1 Risers Air Cushions 2 Water Supply Faucets Figure 6 Installation Step 4 Non Gravity Drain Models Only Connect Drain Hose to Drain Receptacle Remove the drain hose from its shipping position on the rear of the washer by removing the shipping tape IMPORTANT Drain receptacle must be capable of handling a minimum of 1 3 8 inch 3 5 cm outside diameter drain hose FLW1978N 1 Shipping Tape Figure 7 802734 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 11 Installation Standpipe Installation Place the drain hose into the standpipe Remove the beaded tie down strap from accessories bag and place around standpipe and drain hose and tighten strap to hold hose to standpipe Refer to Figure 8 This will prevent the drain hose from dislodging from drain receptacle during use 24 TO 36 in 61 TO 91 44 cm y RECOMMENDED HEIGHT 7
9. the lever swings freely 16 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 802734 Installing Extension Onto Coin Slide Option 1 1 Install slide extension onto top of coin slide using two remaining screws and lockwashers Refer to Figure 15 Attaching Screws Tg Lockwashers d Se amp Coin Slide Slide Extension TLW1564K Figure 15 2 Insert coins and partially extend coin slide 3 Insert coin slide on its side through meter case opening Then rotate 90 degrees to its proper orientation 4 Return coin slide and hook slide pins onto meter case 5 Continue coin slide installation according to manufacturer s instructions NOTE During coin slide installation make sure activation lever is up and off the switch Refer to Figure 16 TLW2090N 1 Lever Off Switch Figure 16 Installation 6 Check to make sure coin slide is operating properly by inserting coins and starting a cycle The IN USE light will turn on or flash if it is already on to indicate proper operation Installing Extension Onto Coin Slide Option 2 1 Install coin slide according to manufacturer s instructions 2 Insert coins into coin slide and slowly push slide in Stop before coins fall into coin box This will allow installing extension through meter case service door opening 3 Install slide extension onto top of coin slide using two screws and lockwashers Refer to Figu
10. 8 in locknut and adjust legs until the washer is level from side to side and front to back using a level Washer should not rock Tighten the locknuts securely against the washer base using the 7 8 in wrench If the locknuts are not tight washer will move out of position during operation 8 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 802734 NOTE DO NOT slide washer across floor if the leveling legs have been extended as legs and base could become damaged Remove rubber feet from accessories bag and place on all four leveling legs Verify that unit doesn t rock FLW2125N Leveling Leg Washer Base Level Wood Block Locknut Rubber Foot oahwnd Figure 3 Installation Step 3 Connect Fill Hoses AL warwine Under certain conditions hydrogen gas may be produced in a hot water system that has not been used for two weeks or more HYDROGEN GAS IS EXPLOSIVE If the hot water system has not been used for such a period and before using the washer turn on all hot water faucets and let the water flow from each for several minutes This will release any accumulated hydrogen gas The gas is flammable Do not smoke or use an open flame during this time W029 Water Supply Water supply faucets must fit standard 3 4 inch 19 1 mm female garden hose couplings DO NOT USE SLIP ON OR CLAMP ON CONNECTIONS Water supply faucets should be readily accessible to
11. ANT Remove all sharp objects from laundry to avoid tears and rips to items during normal machine operation Step 1 Load Laundry Load items loosely into wash drum NOTE Small items such as baby socks may get caught around the door Place these articles inside a mesh garment bag Operation Step 2 Close Loading Door Close loading door tightly The washer will not operate with the loading door open FLW2131N FLW2132N Figure 24 When washing bulky items such as blankets and comforters use the DELICATES COLD cycle The cycle includes agitation and final spin speeds that maintain the load s balance and minimize wear to the articles Figure 25 802734 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 21 Operation Step 3 Add Laundry Supplies Step 4 Set Fabric Selector and Wash Open dispenser drawer Measure and add low sudsing Temperature high efficiency HE detergent 1 bleach 2 and Push touchpad for NORMAL HOT NORMAL fabric softener 3 to the dispenser drawer refer to WARM PERM PRESS WARM or DELICATES Figure 26 Close dispenser drawer COLD cycle Light indicates selection IMPORTANT If using non HE detergent avoid NOTE Changes can be made to Fabric Selector oversudsing by using 1 2 of the detergent setting up until the first fill is complete manufacturer s recommended amount EN V FLW1920N
12. E The wiring diagram is located in the control hood A warno To reduce the risk of fire electric shock serious injury or death all wiring and grounding MUST conform with the latest edition of the National Electrical Code ANSI NFPA No 70 and such local regulations as might apply It is the customer s responsibility to have the wiring fuses and circuit breakers installed by a qualified electrician to make sure adequate electrical power is available to the washer When plugging in the washer e DO NOT overload circuits e DO NOT use an extension cord e DO NOT use an adapter e DO NOT operate other appliances on the same circuit Use separately fused 15 Amp circuits The washer is designed to be operated on a separate branch polarized three wire effectively grounded 120 Volt 60 Hertz AC alternating current circuit protected by a 15 ampere fuse equivalent fusetron or circuit breaker The three prong grounding plug on the power cord should be plugged directly into a polarized three slot effectively grounded receptacle rated 110 120 Volts AC alternating current 15 Amps Refer to Figure 12 to determine correct polarity of the wall receptacle Standard 120 Volt 60 Hertz 3 Wire Effectively Grounded Circuit DRY2022N L1 Ground Neutral Side Round Grounding Prong Neutral oc ond Figure 12 To reduce the risk of an electric shock or fire DO NOT use an extension cord or an adapt
13. Figure 27 FLW2130N 1 Detergent 2 Bleach 3 Fabric Softener Figure 26 A camo Dispenser drawer requires a special tool for removal Contact a service person if removal is necessary W236 22 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 802734 Step 5 Insert Coin s or Card To Insert Money Insert coin s in coin slot Check pricing as seen on digital display O i W3871 To Insert Card Insert card into opening Figure 28 INSERT CARD HERE DRY1927N Figure 29 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Operation Step 6 Start Washer After vend price has been satisfied push the START pad DOOR MUST BE CLOSED TO START WASHER PERM NORMAL e eo PRESS HoT 4 WARM D FLW1923N Figure 30 23 Operation Indicator Lights WASH WASH is lit at the beginning of a wash cycle and will remain lit until the wash cycle is complete RINSE RINSE is lit at the beginning of all RINSE cycles and will remain lit until the rinse cycle is complete SPIN SPIN is lit for all spin cycles DOOR LOCKED DOOR LOCKED is lit whenever the door is locked The door cannot be opened when this light is on START START flashes one second on and one second off when the full vend price has been satisfied IMPORTANT If washer fails to operate properly after in
14. Frontload Washers Metered Commercial 9 FLW1526C Para bajar una copia de estas instrucciones en espa ol visite www comlaundry com Keep These Instructions for Future Reference If this machine changes ownership this manual must accompany machine m Vil i a n c e Part No 802734R5 Laundry Systems www comlaundry com September 2010 uonteaodQo uonev rejsu AL ar Failure to install maintain and or operate this machine according to the manufacturer s instructions may result in conditions which can produce bodily injury and or property damage NOTE The WARNING and IMPORTANT instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur It must be understood that common sense caution and carefulness are factors which cannot be built into these washers These factors MUST BE supplied by the person s installing maintaining or operating the washer Always contact the distributor service agent or the manufacturer about any problems or conditions you do not understand 802734 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 1 Safety Inf DEET 4 Table of afety Information Explanation of Safety Messages C O n t e n t S Important Safety Instructions essen 4 Installation coa cette eee beet 6 Dimensions and Specifications essere 6 Before Y OW Starts sis etitm i seats ei ee n Aie ANE 7
15. Systems LLC DO NOT COPY or TRANSMIT 15 Installation Vending Meter Case The factory mounted coin meter case does not include the service door lock coin slide coin drawer coin drawer lock or keys These parts must be ordered at extra cost according to the purchaser s requirements direct from the manufacturer of your choice NOTE On models with standard capacity meter case and high capacity meter case models starting with Serial Nos beginning 1010 you have the option of using a screw type lock or a 1 4 turn lock on the meter case service door If you choose to use a screw lock then the special bracket located inside the meter case must be used DO NOT use the special bracket if a 1 4 turn lock is used High capacity meter case models with Serial Nos beginning 0910 through 1010 use 1 4 turn lock only Coin Drawer Security Models with standard capacity meter case and high capacity meter case models starting with Serial Nos beginning 1010 only For additional security drill out the two pilot holes on each side of the front of the meter case to 1 4 or 5 16 inch 6 4 or 7 9 mm holes and install a bicycle lock through these holes NOTE An 8 in 20 32 cm coin drawer is required for coin operated electronic control models with standard capacity meter case and high capacity meter case models starting with Serial Nos beginning 1010 High capacity meter case models with Serial Nos beginning 0910 through 1010 requi
16. Temperature e Check fill hoses Make sure hot faucet hose is connected to hot mixing valve indicated with H on the valve bracket and cold faucet is connected to cold mixing valve indicated with C on the valve bracket e Make sure laundry room water heater is adjusted properly 802734 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 31 Contact Information If service is required contact the nearest Factory Authorized Service Center If you are unable to locate an authorized service center or are unsatisfied with the service performed on your unit contact Alliance Laundry Systems Shepard Street P O Box 990 Ripon WI 54971 0990 U S A www comlaundry com Phone 920 748 3121 FLW2123N 1 Nameplate Figure 40 32 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT When calling or writing about your unit PLEASE GIVE THE MODEL AND SERIAL NUMBERS The model and serial numbers are located on the nameplate The nameplate will be in the location shown in Figure 40 Date Purchased Model Number Serial Number Please include a copy of your bill of sale and any service receipts you have WARNING To reduce the risk of serious injury or death DO NOT repair or replace any part of the unit or attempt any servicing unless specifically recommended in the user maintenance instructions or in published user repair ins
17. bber washer into the other end of each fill hose that will connect to the water mixing valve at the rear of the washer Refer to Figure 4 Thread hose couplings onto valve connections finger tight then approximately 1 4 turn with pliers IMPORTANT DO NOT cross thread or overtighten couplings Turn water on and check for leaks If leaks are found retighten the hose couplings Continue tightening and rechecking until no leaks are found IMPORTANT Hoses and other natural rubber parts deteriorate after extended use Hoses may develop cracks blisters or material wear from the temperature and constant high pressure they are subjected to All hoses should be checked on a monthly basis for any visible signs of deterioration Any hose showing the signs of deterioration listed above should be replaced immediately All hoses should be replaced every five years TLW1976N Faucet Fill Hoses Plain Rubber Washer Filter Screens hon WATER MIXING VALVE FLW1977N Water Supply Faucets Hot Water Connection Cold Water Connection Fill Hoses 1 2 3 4 Figure 4 Figure 5 IMPORTANT Turn off water supply faucets after check out and demonstration Owner should turn off water supply whenever there will be an extended period of non use NOTE Longer fill hoses are available as optional equipment at extra cost if the hoses supplied with the washer are not long enough for
18. cle press the PUSH TO START button FLW2129N 1 Detergent 2 Bleach 3 Fabric Softener Figure 20 W2971 1 Service Door Figure 23 802734 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 19 Operation Indicator Lights IN USE This light will remain on while washer is in use DOOR LOCKED This light will come on after the PUSH TO START button has been pressed and the washer door has locked It will remain on until the wash cycle has ended FINAL SPIN AND TUMBLE This light will come on at the start of the final spin and remain on until the wash cycle has ended CLOSE DOOR This light will come on if door is not closed tightly Firmly push door until light goes out IMPORTANT If washer fails to operate properly after installation make sure electrical service and water supply faucets are turned on Are all the controls properly set Have a qualified service person refer to the wiring diagram located inside of cabinet and check for broken loose or incorrect wiring NOTE Once a cycle has started the door can only be opened by first unplugging the power cord and waiting one minute AL wanne To reduce the risk of bodily injury do not remove laundry from washer until all lights are out and all moving parts have stopped W092 The washer will stop pause shortly before the first spin and final spin 20 Copyright Alliance Laundry Systems LLC
19. dry Systems LLC DO NOT COPY or TRANSMIT TE 32 Safety Information Explanation of Safety Messages Throughout this manual and on machine decals you will find precautionary statements DANGER WARNING and CAUTION followed by specific instructions These precautions are intended for the personal safety of the operator user servicer and those maintaining the machine Indicates an imminently hazardous situation that if not avoided will cause severe personal injury or death Indicates a hazardous situation that if not avoided could cause severe personal injury or death CAUTION Indicates a hazardous situation that if not avoided may cause minor or moderate personal injury or property damage Additional precautionary statements IMPORTANT and NOTE are followed by specific instructions IMPORTANT The word IMPORTANT is used to inform the reader of specific procedures where minor machine damage will occur if the procedure is not followed NOTE The word NOTE is used to communicate installation operation maintenance or servicing information that is important but not hazard related Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Important Safety Instructions Save These Instructions WARNING To reduce the risk of fire electric shock serious injury or death to persons when using your washer follow these basic precautions 1 Read a
20. e has started the door can only be opened by first unplugging the power cord and waiting one minute To reduce the risk of bodily injury do not remove laundry from washer until all lights are out and all moving parts have stopped w092 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 27 Maintenance User Maintenance Instructions Lubrication All moving parts are sealed in a permanent supply of lubricant or are equipped with oilless bearings Additional lubrication will not be necessary Do not lubricate the door hinge If the hinge makes noise replace the hinge Cold Weather Care If the washer is delivered on a cold day below freezing or is stored in an unheated room or area during the cold months do not attempt to operate it until the washer has had a chance to warm up Care of Your Washer Use only a damp or sudsy cloth for cleaning the control panel Some cleaning product sprays may harm the finish on the control panel or damage the interior of the hood Wipe the washer cabinet as needed If detergent bleach or other washing products are spilled on the cabinet wipe immediately Some products will cause permanent damage if spilled on the cabinet Do not use scouring pads or abrasive cleansers The wash drum will need no particular care although it may need rinsing or wiping after an unusual load has been washed The outside of the door window can be cleaned with household w
21. earing in this manual are not meant to cover all possible conditions and situations that may occur Common sense caution and care must be exercised when installing maintaining or operating the washer Always contact your dealer distributor service agent or the manufacturer about any problems or conditions you do not understand Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Installation Dimensions and Specifications Coin Slide Models 21 56 in 54 76 cm Electronic Control Models 22 06 in 56 03 cm 25 24 in ZE e n vo lt 61 0 cm S7 8 o af O E E Sa 5 oE o ce BESS i 8 25 3 22 Sait EN su 222 see E g Ye 27385850 o gt SEET o TL QOR vw e 92 eise E o v ote oO Ee 3 S I o T otc o 0 e Zo e 5 On o 9 D Dei L zess in 68 3 eme 28 in 71 1 cm gt 2 in DES K 5 1 cm 1 5 in 3 8 cm MODELS EQUIPPED WITH DRAIN HOSE FLW2201N Coin Slide Models 21 56 in 54 76 cm Electronic Control Models 22 06 in 56 03 cm SE WER 2E NY 24 in Er Sr of lt 1 as ES E 2 Sp E oe Wi Ee 9 d e 23 Ce 2 3 2s T E c as 29 E o 22 52 6 9 Beant e os 52 ri SS SZ E oo boc ka 3 E 2 UR Oc Da 0 cf s m0 33 3 cm 33 30 Q oo ES D
22. eather 10 Do not tamper with the controls 802734 11 12 13 14 15 16 17 18 19 802734 Do not repair or replace any part of the washer or attempt any servicing unless specifically recommended in the user maintenance instructions or in published user repair instructions that you understand and have the skills to carry out To reduce the risk of an electric shock or fire DO NOT use an extension cord or an adapter to connect the washer to the electrical power source Use your washer only for its intended purpose washing clothes ALWAYS disconnect the washer from electrical supply before attempting any service Disconnect the power cord by grasping the plug not the cord Install the washer according to the INSTALLATION INSTRUCTIONS All connections for water drain electrical power and grounding must comply with local codes and be made by licensed personnel when required Do not do it yourself unless you know how To reduce the risk of fire clothes which have traces of any flammable substances such as vegetable oil cooking oil machine oil flammable chemicals thinner etc or anything containing wax or chemicals such as in mops and cleaning cloths must not be put into the washer These flammable substances may cause the fabric to catch on fire by itself Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or pr
23. er the panel to remove it from the washer NOTE The pump may have some water in it Usea rag or a container to catch water If the wash drum is full of water use a wet dry shop vacuum to catch the water With rag or vacuum ready unscrew the cap on the left side of the pump and remove trap Clean the debris from the trap Reinstall the trap and access panel Reconnect washer to electrical supply Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 29 Troubleshooting Try these troubleshooting tips before making a service call They may save time and money Washer Symptom Possible Cause Solution Won t Fill Make sure power cord is plugged all the way into the electrical outlet Make sure hot and cold water faucets are turned on Make sure that the fill hoses are not kinked or twisted Press PUSH TO START button or START keypad Make sure that the controls are properly set Make sure that the loading door is closed tightly Check the laundry room fuse or circuit breaker Clean the screens in the water mixing valve and the filter screens located at the faucet end of the fill hoses Won t Start Make sure loading door is closed tightly Press PUSH TO START button or START keypad Make sure power cord is plugged all the way into the electrical outlet Check the laundry room fuse or circuit breaker Insert coin s or card Activate time accumulator Push the coin slide all the way in c
24. er to connect the washer to the electric power source 14 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 802734 Grounding Instructions The washer must be grounded In the event of malfunction or breakdown grounding will reduce the risk of electric shock by providing a path of least resistance for electric current The washer is equipped with a cord having an equipment grounding conductor and a three prong grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances A wanne Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or service person if you are in doubt as to whether the washer is properly grounded DO NOT modify the plug provided with the washer if it will not fit the outlet have a proper outlet installed by a qualified electrician NOTE Have a qualified electrician check the polarity of the wall receptacle If a voltage reading is measured other than that in Figure 12 the qualified electrician should correct the problem 802734 Installation Step 9 Check Installation Refer to Installer Checklist on the back cover of this manual and make sure that washer is installed correctly Run washer through one complete cycle to make sure it is operating properly Copyright Alliance Laundry
25. igh efficiency HE detergent and proper load sizes Make sure outside perimeter of the door glass where seal contacts glass is clean 30 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 802734 Troubleshooting Washer Symptom Possible Cause Solution Too Many Soap Suds e Laundry load may be oversudsing Make sure you are using low sudsing high efficiency HE detergent e Make sure you are using the amount of detergent recommended on the detergent s label If using non HE detergent use only 1 2 of the detergent manufacturer s recommended amount e Laundry load may be overloaded Make sure you are using proper load sizes Vibrates Moves e Make sure washer is level Uneven leveling can cause vibration Slightly e Make sure washer is installed on a solid sturdy and level floor The washer should not be installed on carpeting soft tile a platform or other weakly supported structures e Make sure rubber feet are installed on all four leveling legs Refer to Installation section Step 5 Is Noisy e Make sure washer is level Uneven leveling can cause vibration e Some sounds may be a part of normal operation for a frontload washer Load is too Wet e Wash load may be unbalanced The washer may have limited the spin speed to prevent damage to the machine Redistribute the load e Load is too small Add items to make full load Wrong Water e Make sure that the controls are properly set
26. indow cleaner Running an occasional rinse cycle with bleach will help to avoid a musty smell in the wash drum Cleaning Glass Sealing Area In order to assure that the door properly seals against water leaks the following surfaces should be wiped off periodically e The outside perimeter of the door glass where the seal contacts the glass e The front surface of the door seal lip Usually a mild soap solution will work If there is an extreme build up of minerals from a hard water supply the surfaces may need to be cleaned with a lime removal chemical 28 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Replacing Hoses Hoses and other natural rubber parts deteriorate after extended use Hoses may develop cracks blisters or material wear from the temperature and constant high pressure they are subjected to All hoses should be checked on a monthly basis for any visible signs of deterioration Any hose showing the signs of deterioration listed above should be replaced immediately All hoses should be replaced every five years Filter Screens Check the filter screens in the fill hoses for debris or damage annually Clean or replace them if necessary If the washer is filling with water slower than normal check the filter screens Clean or replace them if necessary Order filter screen Part No F270300 from the nearest authorized parts distributor Vacations and Extended Non Use IMPORTANT T
27. ll instructions before using the washer 2 Refer to the GROUNDING INSTRUCTIONS in the INSTALLATION manual for the proper grounding of the washer 3 Do not wash articles that have been previously cleaned in washed in soaked in or spotted with gasoline dry cleaning solvents or other flammable or explosive substances as they give off vapors that could ignite or explode 4 Do not add gasoline dry cleaning solvents or other flammable or explosive substances to the wash water These substances give off vapors that could ignite or explode 5 Under certain conditions hydrogen gas may be produced in a hot water system that has not been used for two weeks or more HYDROGEN GAS IS EXPLOSIVE If the hot water system has not been used for such a period before using a washing machine or combination washer dryer turn on all hot water faucets and let the water flow from each for several minutes This will release any accumulated hydrogen gas The gas is flammable do not smoke or use an open flame during this time 6 Do not allow children to play on or in the washer Close supervision of children is necessary when the washer is used near children This is a safety rule for all appliances 7 Before the washer is removed from service or discarded remove the door to the washing compartment 8 Do not reach into the washer if the wash drum is moving 9 Do not install or store the washer where it will be exposed to water and or w
28. n the yellow rope Remove label from front side of front access panel or shipping brace and place on backside of front access panel for future reference NOTE The shipping brace bolts washers and shock sleeves should be saved and MUST be reinstalled whenever the washer is moved more than 4 feet 1 22 m Refer to User Maintenance section for instructions Do not lift or transport washer from front or without shipping materials installed Store the shipping materials in the accessories bag Save materials for use whenever the washer is moved Reinstall front access panel IMPORTANT DO NOT tip washer more than 6 inches 152 4 mm in any direction after shipping brace has been removed Shock absorbers may separate and damage to washer may result For leveling purposes the washer may be tilted a maximum of 6 inches 152 4 mm in any direction Installation FLW2124N Shock Sleeves Motor Mount Hooked End of Shipping Brace Bolts and Lockwashers hon Figure 10 Step 7 Wipe Out Inside of Wash Drum Before using washer for the first time use an all purpose cleaner or a detergent and water solution and a damp cloth to remove shipping dust from inside wash drum FLW2126N Figure 11 802734 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 13 Installation Step 8 Plug In the Washer Electrical Requirements 120 Volt 60 Hertz with 3 Prong Grounding Plug NOT
29. nstall the washer on carpeting soft tile a platform or other weakly supported structures n TE a A A E Figure 2 Step 2 Position and Level the Washer A wanne Washers elevated above floor level must be anchored to that elevated surface base or platform The material used to elevate the washer should also be anchored to the floor to ensure that the washer will not walk or that the washer can not be physically pulled tipped or slid from its installed position Failure to do so may result in conditions which can produce serious injury death and or property damage Position washer so it has sufficient clearance for installation and servicing NOTE Use of the dispenser drawer or washer door as a handle in the transportation of the washer may cause damage to the dispenser or door Place washer in position on a solid sturdy and level floor Installing the washer on any type of carpeting soft tile a platform or other weakly supported structures is not recommended Place a level on the cabinet top and check if the washer is level from side to side and front to back NOTE Level must rest on raised portion of top panel Refer to Figure 3 If washer is not level tilt washer to access the front and rear leveling legs For easier access to leveling legs prop up washer with a wooden block Refer to Figure 3 Loosen 7
30. o avoid possible property damage due to flooding turn off the water supply to the washer whenever there will be an extended period of non use Leave the loading door open during extended periods of non use to allow the wash drum to dry out and avoid a musty smell 802734 Reinstallation of Shipping Materials To prevent damage while moving the washer the shipping materials MUST be reinstalled Disconnect washer from electrical supply While supporting the front access panel remove two screws from the bottom edge of the panel Gently lower the panel to remove it from the washer Place the shock sleeves on all four shock absorbers Refer to Figure 39 Insert hooked end of shipping brace into the open slot of the motor mount Refer to Figure 39 Attach the brace with the five bolts and washers Refer to Figure 39 Reinstall front access panel FLW2124N Shock Sleeves Motor Mount Hooked End of Shipping Brace Bolts and Lockwashers A amp oxNA Figure 39 Refer to Installation section step 6 for proper procedures whenever the washer is moved 802734 Maintenance Cleaning Foreign Object Trap The washer s pump has a trap that may collect foreign objects The trap may need to be cleaned if water is draining slower than usual To clean Disconnect washer from electrical supply While supporting the front access panel remove two screws from the bottom edge of the panel Gently low
31. oduct Keep your washer in good condition Bumping or dropping the washer can damage safety features If this occurs have your washer checked by a qualified service person If the supply cord is damaged it must be replaced by a special cord or assembly available from the manufacturer or its service agent 20 21 22 23 24 25 26 27 Safety Information Be sure water connections have a shut off valve and that fill hose connections are tight CLOSE the shut off valves at the end of each wash day Loading door MUST BE CLOSED any time the washer is to fill tumble or spin DO NOT bypass the loading door switch by permitting the washer to operate with the loading door open Always read and follow manufacturer s instructions on packages of laundry and cleaning aids Heed all warnings or precautions To reduce the risk of poisoning or chemical burns keep them out of the reach of children at all times preferably in a locked cabinet Always follow the fabric care instructions supplied by the garment manufacturer Never operate the washer with any guards and or panels removed DO NOT operate the washer with missing or broken parts DO NOT bypass any safety devices Failure to install maintain and or operate this washer according to the manufacturer s instructions may result in conditions which can produce bodily injury and or property damage NOTE The WARNING and IMPORTANT SAFETY INSTRUCTIONS app
32. oin slide models only Make sure door latch is properly adjusted relative to door lock Won t Spin Tumble Make sure loading door is closed tightly Press PUSH TO START button or START keypad Make sure power cord is plugged all the way into the electrical outlet Make sure controls are properly set Check the laundry room fuse or circuit breaker Broken drive belt Call the service person Foreign object trap in pump may be clogged Clean the trap Refer to Maintenance section Stops Pauses During Cycle Pauses are part of the washer s normal operation Wash load may be unbalanced Washer will stop and then restart spin automatically Check the laundry room fuse or circuit breaker Won t Drain Make sure drain hose is not kinked or twisted Make sure drain hose is not clogged Make sure drain receptacle is not clogged Refer to the Installation section to make sure that the drain hose has been properly installed Foreign object trap in pump may be clogged Clean the trap Refer to Maintenance section Water Leaks Check that fill hoses are properly installed on the faucets and the washer s water mixing valve Check the condition of the fill hoses Replace fill hoses every five years Check the condition of the rubber door gasket for tears or holes Make sure drain receptacle is not clogged Check building plumbing Laundry load may be oversudsing or overloaded Make sure you are using low sudsing h
33. permit turning them off when washer is not being used Recommended cold water temperature is 60 to 80 Fahrenheit 16 to 27 Celsius Recommended maximum hot water temperature is 125 Fahrenheit 51 Celsius Warm water is a mixture of hot and cold water Warm water temperature is dependent upon water temperature and pressure of both the hot and cold water supply lines To prevent personal injury avoid contact with inlet water temperatures higher than 125 Fahrenheit 51 Celsius and hot surfaces Water pressure must be a minimum of 20 to a maximum of 120 pounds per square inch 138 to 827 kPa static pressure measured at the faucet NOTE Water pressure under 20 pounds per square inch 138 kPa will cause an extended fill time in the washer and may not properly flush out the detergent dispenser 802734 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 9 Installation Turn on the water supply faucets and flush the lines for approximately two minutes to remove any foreign materials that could clog the screens in the water mixing valve NOTE When installing in newly constructed or renovated building it is very important to flush the lines since build up may have occurred during construction Connecting Hoses Insert each filter screen into the end of each fill hose that will connect to the water supply faucet The screen must be facing outward Refer to Figure 4 Insert each plain ru
34. r tightly The washer will not operate with the loading door open FLW2132N Figure 32 802734 Operation Step 3 Add Laundry Supplies Open dispenser drawer Measure and add low sudsing high efficiency HE detergent 1 bleach 2 and fabric softener 3 to the dispenser drawer refer to Figure 33 Close dispenser drawer IMPORTANT If using non HE detergent avoid oversudsing by using 1 2 of the detergent manufacturer s recommended amount FLW2130N 1 Detergent 2 Bleach 3 Fabric Softener Figure 33 Al Game Dispenser drawer requires a special tool for removal Contact a service person if removal is necessary W236 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 25 Operation Step 4 Set Fabric Selector Push touchpad for NORMAL PERM PRESS or DELICATES cycle Light indicates selection NOTE Changes can be made to Fabric Selector setting up until the first fill is complete Step 6 Insert Coin s or Card To Insert Money Insert coin s in coin slot Check pricing as seen on digital display H2051 E O W3871 Figure 34 Step 5 Set Wash Temperature Push touchpad for HOT WARM or COLD Light indicates selection NOTE Always follow manufacturer s care labels H2061 Figure 35 Figure 36 To Insert Card Insert card into opening Do not remove the card until
35. re 15 NOTE Make sure extension lever is above switch activation lever 4 Check to make sure coin slide is operating properly by inserting coins and starting a cycle The IN USE light will turn on or flash if it is already on to indicate proper operation Models Prepped for Card Reader The machine is shipped from the factory with the Electronic Control Diagnostic Harness Assembly unplugged To avoid unauthorized manual programming or vending perform the following steps 1 Open control panel Refer to Figure 17 2 Locate diagnostic harness on electronic control 3 Plug connectors for white black wire and red blue wire together FLW6R 1 Control Panel Figure 17 802734 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 17 Operation Operation Instructions for Coin Slide Operated Washers IMPORTANT Prior to first wash use an all purpose cleaner or a detergent and water solution and a damp cloth to remove shipping dust from inside of washtub IMPORTANT Remove all sharp objects from laundry to avoid tears and rips to items during normal machine operation Step 1 Load Laundry Load items loosely into wash drum NOTE Small items such as baby socks may get caught around the door Place these articles inside a mesh garment bag Step 2 Close Loading Door Close the loading door tightly The washer will not operate with the loading door open
36. re a 7 21 in 18 31 cm coin drawer Slide Extension Coin Slide Models with standard capacity meter case and high capacity meter case models starting with Serial Nos beginning 1010 only NOTE High capacity meter case models with Serial Nos beginning 0910 through 1010 require a coin slide with a switch installed on it 1 Remove slide extension parts from parts accessories bag included in unit 2 If installing a Greenwald coin slide position extension lever to be installed on extension bracket with arm that has one star facing down Refer to Figure 13 Greenwald Monarch or Coin Slide ESD Coin Slide One Star Two Stars TLW2088N Figure 13 3 If installing a Monarch or ESD coin slide position lever with arm that has two stars facing down Refer to Figure 13 4 Install extension lever with rounded corner facing away from extension bracket using bolt one or two flat washers shims use number of washers included in kit and nut Refer to Figure 14 Make sure washers are flat against bracket One or Two Spring Bolt Flat Washers Shims Rounded Corner Extension Bracket Extension Lever Star s Facing Down TLW2089N Figure 14 5 Torque nut between 2 and 2 26 Nm 18 and 20 inch pounds or tighten nut firmly 6 Install extension spring in bracket hole and hole in upper arm of lever Refer to Figure 14 7 Bend loops closed after installation 8 Check to make sure
37. stallation make sure electrical service and water supply faucets are turned on Are all the controls properly set Have a qualified service person refer to the wiring diagram located inside of washer control hood and check for broken loose or incorrect wiring NOTE Once a cycle has started the door can only be opened by first unplugging the power cord and waiting one minute A wann To reduce the risk of bodily injury do not remove laundry from washer until all lights are out and all moving parts have stopped w092 24 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 802734 Operation Instructions for NetMaster Washers IMPORTANT Prior to first wash use an all purpose cleaner or a detergent and water solution and a damp cloth to remove shipping dust from inside of washtub IMPORTANT Remove all sharp objects from laundry to avoid tears and rips to items during normal machine operation Step 1 Load Laundry Load items loosely into wash drum NOTE Small items such as baby socks may get caught around the door Place these articles inside a mesh garment bag FLW2131N Figure 31 When washing bulky items such as blankets and comforters use the DELICATES cycle The cycle includes agitation and final spin speeds that maintain the load s balance and minimize wear to the articles Step 2 Close Loading Door Close loading doo
38. tructions that you understand and have the skills to carry out W329 If replacement parts are required contact the source from where you purchased your washer or call 920 748 3950 for the name and address of the nearest authorized parts distributor 802734 Installer Checklist Fast Track for Installing the Washer Refer to the manual for more detailed information Position Washer Near Installation Area O Position and Level the Washer FLW2125N Remove the Shock Sleeves and Shipping Brace FLW2124N IT CHECK C CHECK Non Gravity Drain Models Only Connect Drain Hose Q Wipe Out Inside af to Drain Receptacle Wash Drum FLW1979N C CHECK C CHECK Gravity Drain Models Only Connect Drain Outlet to Drain System Plug In the Washer D254IE0A FLW1980N C CHECK Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT

Download Pdf Manuals

image

Related Search

Related Contents

  Manuale  Manual del usuario  Septembre 2009 - Pont-Péan  取扱説明書  WS1_(Hai Wang Charger) dutch user manual  

Copyright © All rights reserved.
Failed to retrieve file