Alliance Laundry Systems 70269501R3 Snow Blower User Manual
Contents
1. TMB2025N 1 Serial plate Figure 1 Conversion Table Multiply By To Obtain Multiply By To Obtain Btu 0 252 kCal Pounds sq inch 0 06895 Bars Btu 1055 Joules Pounds sq inch 0 070 kg sq cm Inch 25 4 Millimeters Pounds lbs 0 454 Kilograms Inches W C 0 036 Pounds sq inch Boiler Horsepower 33 479 Btu hr Inches W C 0 249 kPa Boiler Horsepower 34 5 Ibs steam hr Ib inch psi 6 895 kPa CFM 0 471 liters second ft 28 32 Liters kW 3414 Btu hr Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 70269501 Safety Information Explanation of Safety Messages Precautionary statements DANGER WARNING and CAUTION followed by specific instructions are found in this manual and on machine decals These precautions are intended for the personal safety of the operator user servicer and those maintaining the machine Indicates an imminently hazardous situation that if not avoided will cause severe personal injury or death Indicates a hazardous situation that if not avoided could cause severe personal injury or death A camo Indicates a hazardous situation that if not avoided may cause minor or moderate personal injury or property damage Additional precautionary statements IMPORTANT and NOTE are followed by specific instructions IMPORTANT The word IMPORTANT is used to inf2. manual timer ZR NetMaster network card CD rotary coin drop NC NetMaster coin ZX NetMaster network prep for coin CX prep for coin NR NetMaster card ZY NetMaster network prep for card CY prep for card NX NetMaster prep for coin 70269501 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 5 Introduction Customer Service If literature or replacement parts are required contact the source from which the machine was purchased or contact Alliance Laundry Systems at 920 748 3950 for the name and address of the nearest authorized parts distributor For technical assistance call 920 748 3121 Wiring Diagram The wiring diagram is located in the junction or contactor box Models starting Serial No 0309 or later will have the wiring diagram part number in the lower portion of the electrical data on the serial plate Serial Plate Location When calling or writing for information about your product be sure to mention model and serial numbers Model and serial numbers are found on serial plate on rear of machine and inside door hinge Refer to Figure 1 LE 25 30 AND 35 POUND TUMBLERS
3. Models 11 Operating Instructions ss 11 Step 1 Clean Lint Screen Compartment 11 Step 2 Load Laundry screech veccisicceds les amendes 11 Step 3 Determine Control Type and Temperature Setting 11 Step 4 Remove Laundry ss 11 Electromechanical Coin Control 12 Electronic Coin Control 13 Manual Times ist ten ir tte E E a E a aS 14 Electronic OPL Controlis esse aenn onae e A naio E REE E 15 MDG Comm Control ai ss aren e e ni o ra a 16 MDC Card Contr l sn in in tin 17 NetMaster Coin Control ss 18 NetMaster Card Control 19 Maintenance einen ereer erea Ee EEA EEE EEEE 21 Daily E E a ees 21 Monthly ets better aa gine shed alana dete 23 Quarterly sss tes titine tnt stds AE aN 23 Bi AnNUAI Vs een hide rose tintin entiere 23 Before You Call for Service 27 Customer Services nrrnintmenan ae Re tiene ete eet 27 Copyright 2006 Alliance Laundry Systems LLC All rights reserved No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher 70269501 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 3 Notes Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT
4. for loose electrical connections c Clean dampers and make sure they operate 5 Remove all front panels and vacuum including freely coin drop mechanisms d Replace duct and all access covers before returning to operation 2 Ensure even lint distribution over lint screen 7 Inspect cabinet and inner panels for any damage replace or repair as needed replace if distribution of lint is uneven to maintain proper airflow and avoid overheating 8 Clean burner tubes of any lint buildup Check cylinder and front panel seals 3 Carefully wipe any accumulated lint off the cabinet high limit thermostat and thermistor including perforated cover Lint buildup will act as an insulator causing machine to overheat 4 Clean lint and debris buildup from blower to maintain proper airflow to avoid overheating and prevent possible vibration Quarterly 1 Use a vacuum to clean air vents on drive motors 2 Use a vacuum to clean lint from rear limit thermostat cover 3 Refer to Service Manual on how to check and clean steam coils if applicable 4 Check flow of combustion and ventilation air Check belt tension and condition Replace worn or cracked belts 70269501 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 23 Maintenance To reduce the risk of electric shock fire explosion serious injury or death e Disconnect electric power to the tumbler before servicing e Close gas shut off valve t
5. 5N Figure 9 MDC Card Control IMPORTANT To stop the tumbler at any time during the cycle OPEN DOOR To restart the BL and BY Control Suffixes tumbler CLOSE door and press START pad 1 Select HIGH TEMP MED TEMP LOW TEMP or DELICATES by pressing the appropriate temperature pad 4 When the cycle is complete open door and remove the laundry 2 Insert card into opening 3 Press START pad to start tumbler 70269501 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 17 Operating Instructions 1 2 3 SELECT INSERT PUSH TEMP fh COINS ey DRYING COOL DOWI 70184301 C8511 Figure 10 IMPORTANT To stop the tumbler at any time NetMaster Coin Control during the cycle OPEN DOOR To restart the NC NX ZC and ZX Control Suffixes tumbler CLOSE door and press START pad 1 Select HIGH TEMP MED TEMP LOW TEMP or NO HEAT by pressing the appropriate 4 When the cycles complete open door and temperature pad 2 Insert the coin s in the coin slot 3 Press START pad to start tumbler 18 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 70269501 Operating Instructions 1 2 3 SELECT nent 7 PUSH TEMP CARD START gt e o o o o Code INSERT REMOVE ADD DRYING L grd ale St em INSERT CARD HERE coo CARD CARD TIME DOWN 70184401 C8521 Figure 11 NetMaster Card Control IMPORTANT To
6. 70269501 Introduction Model Identification Information in this manual is applicable to these models Gas Steam Electric HA025L SA025N UT025L HT025S UT025S HT025E UTO25E HA025N STO25L UT025N HU025S UU025S HU025E UU025E HT025L STO25N UU025L ST025S YTO25S STO25E YTO25E 25 Pound HT025N SU025L UU025N SU025S SU025E HUO25L SU025N YTO25L HU025N UA025L YTO25N SA025L UA025N HAO30L SA030L UA030N HT030S UT030S HTO30E UTO30E HA030N SA030N UTO30L HU030S UU030S HU030E UU030E HT030D STO30L UT0O30N STO30S YT030S STO30E YTO30E 30 Pound HT030L STO30N UU030L SU0308S SU030E HT030N SU030L UU030N HUO30L SU030N YTO30L HU030N UA030L YTO30N HAT30L HUT30L SAT30N HTT30S STT30S HTT30E STT30E HAT30N HUT30N STT30L HUT308S SUT30S HUT30E SUT30E T30 HTT30D MTT30N STT30N HTT30L NTT30N SUT30L HTT30N SAT30L SUT30N ATO35L SAO35L UTO35L AT035S UT035S HTO35E UTO35E AT035N SA035N UTO35N HT035S UU035S HU035E UU035E HAO35L STO35L UU035L HU035S YTO35S STO35E YTO35E 35 Pound HAO35N STO35N UU035N ST035S YU035S SU035E YUO35E HTO35L SU035L YTO35L SU035S HTO35N SU035N YTO35N HUO35L UA035L HU035N UA035N Includes models with control suffixes BC basic electronic coin EC EDC electronic coin NY NetMaster prep for card BL basic electronic central pay EX EDC coin ready OM OPL micro BX basic electronic prep for coin EY EDC card ready ZC NetMaster network coin BY basic electronic prep for card MT
7. Drying Tumblers 25 Pound Capacity 30 Pound Capacity 35 Pound Capacity Stacked 30 Pound Capacity Through Serial No 0602004143 Refer to Page 5 for Model Numbers NOTA Para bajar una copia de estas instrucciones en espa ol visite www comlaundry com Keep These Instructions for Future Reference If this machine changes ownership this manual must accompany machine lance Laund ry S ystems www comlaundry com Part No 70269501R3 August 2006 JUBUDJUIBIA UONB1I9dGC Installation must conform with local codes or in the absence of local codes with In the U S A installation must conform to the latest edition of the American National Standard Z223 1 NFPA 54 National Fuel Gas Code and Standard ANSI NFPA 70 National Electric Code In Canada installation must comply with Standards CSA B149 1 or Natural Gas and Propane Code CSA C22 1 latest edition Canadian Electric Code Part I In Australia installation must comply with the Australian Gas Association Installation Code for Gas Burning Appliances and Equipment Al WARNING FOR YOUR SAFETY the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage personal injury or death W033 e Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance e WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance Do not tou
8. RY plastics anything containing wax or chemicals such as mops and cleaning cloths or anything dry cleaned at home with a dry cleaning solvent e DO NOT TUMBLE fiberglass curtains and draperies unless the label says it can be done If they are dried wipe out the cylinder with a damp cloth to remove particles of fiberglass W076 To reduce the risk of serious injury allow cylinder to stop before cleaning lint screen Emergency Stop Button on CE Models All CE approved OPL tumblers are factory equipped with an emergency stop button located on the front panel Refer to Figure 2 TMB1664N 1 Emergency Stop Button Figure 2 To operate emergency stop button a Press red emergency stop button to stop all action b To restart machine pull red emergency stop button out and press START pad or button NOTE Activation of the emergency stop button stops all machine control circuit functions but DOES NOT remove all electrical power from machine 70269501 Operating Instructions Step 1 Clean Lint Screen Compartment Remove any accumulated lint from the lint screen and compartment Close panel tightly against tumbler frame and lock panel securely if applicable IMPORTANT Clean lint screen and lint compartment daily Failure to clean the lint screen daily will result in higher than normal temperatures that may damage laundry Step 2 Load Laundry Open loading door and load cylinder with laund
9. binet Do not tumble fiberglass curtains and draperies unless the label says it can be done If they are dried wipe out the cylinder with a damp cloth to remove particles of fiberglass Always follow the fabric care instructions supplied by the garment manufacturer Never operate the tumbler with any guards and or panels removed DO NOT operate the tumbler if it is smoking grinding has missing or broken parts 29 30 31 Safety Information DO NOT bypass any safety devices Solvent vapors from dry cleaning machines create acids when drawn through the heater of the drying unit These acids are corrosive to the tumbler as well as to the laundry load being dried Be sure make up air is free of solvent vapors Failure to install maintain and or operate this machine according to the manufacturer s instructions may result in conditions which can produce bodily injury and or property damage To reduce the risk of serious injury install lockable door s to prevent public access to rear of tumblers Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT W055 Notes 10 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 70269501 Operating Instructions To reduce the risk of fire DO NOT DRY articles containing foam rubber or similarly textured rubberlike materials DO NOT D
10. ch any electrical switch do not use any phone in your building Clear the room building or area of all occupants Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions If you cannot reach your gas supplier call the fire department e Installation and service must be performed by a qualified installer service agency or the gas supplier W052 FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance W053 A MISE EN GARDE POUR VOTRE S CURIT veillez bien respecter les indications de ce manuel afin de minimiser les risques d incendie ou d explosion ou d carter les dangers de dommages mat riels corporel ou de mort W033FR e Ne pas entreposer ni utiliser d essence ni d autres vapeurs ou liquides inflammables dans le voisinage de cet appareil ou de tout autre appareil QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ Ne pas tenter d allumer d apareil Ne touchez a aucun interrupteur Ne pas vous servir des t l phones se trouvant dans le b timent o vous vous trouvez Evacuez la pi ce le b timent ou la zone Appelez imm diatement votre fournisseur de gaz depuis un voisin Suivez les instructions du fournisseur Si vous ne pouvez rejoindre le fournisseur de gaz appelez le service des incendies e L installation et l
11. ect electric power to the tumbler before servicing e Close gas shut off valve to gas tumbler before servicing e Close steam valve to steam tumbler before servicing e Never start the tumbler with any guards panels removed e Whenever ground wires are removed during servicing these ground wires must be reconnected to ensure that the tumbler is properly grounded Quarterly Maintenance Use a vacuum to clean air vents on drive motors Use a vacuum to clean lint from rear limit thermostat cover Refer to Service Manual on how to check and clean steam coils Check flow of combustion and ventilation air Check belt tension and condition Replace worn or cracked belts Bi Annually Maintenance Check mounting hardware for any loose nuts bolts or screws Check gas connections for leakage Check for loose electrical connections Check steam connections for looseness and leakage Remove all front panels and vacuum including coin drop mechanisms Check cylinder and front panel seals Inspect cabinet and inner panels for any damage replace or repair as needed Clean burner tubes of any lint buildup 70269501 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 25 Notes 26 Copyright Alliance Lau
12. entretien doivent tre assur s par un installateur ou un service d entretien qualifi ou par le fournisseur de gaz W052Q POUR VOTRE SECURITE Ne pas entreposer ni utiliser d essence ou autres gaz et liquides inflammables au voisinage de cet appareil ou de tout autre WO53FR IMPORTANT Information must be obtained from a local gas supplier on instructions to be followed if the user smells gas These instructions must be posted in a prominent location Step by step instructions of the above safety information must be posted in a prominent location near the tumbler for customer use 70269501 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 1 Notes Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 70269501 Table of Contents Introduction 5 48iititetese tft ete tt 5 Model Identification sente mn hein 5 Customer SEVICE sn rm nt ence de Aer eae eae 6 Wiring Dia stain oeie ens enpe ae a nice etienne indien 6 Seral Plate LOCATION 3 58 en nee net Re i es 6 Safety Information 7 Explanation of Safety Messages 7 Important Safety Instructions 2 0 eee eeseeseceseceeeeeseeeaeceaeceseeeeeeeneenaees 8 Operating Instructions 11 Emergency Stop Button on CE
13. ic power to the tumbler before servicing e Close gas shut off valve to gas tumbler before servicing e Close steam valve to steam tumbler before servicing e Never start the tumbler with any guards panels removed e Whenever ground wires are removed during servicing these ground wires must be reconnected to ensure that the tumbler is properly grounded 1 25 30 AND 35 POUND TMB2121N io aan 1 Lint Screen 4 Thermistor 2 Guard 5 Blower Housing 3 Cabinet Thermostat Figure 12 22 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 70269501 Maintenance To reduce the risk of electric shock fire explosion serious injury or death e Disconnect electric power to the tumbler before servicing e Close gas shut off valve to gas tumbler before servicing e Close steam valve to steam tumbler before servicing e Never start the tumbler with any guards panels removed e Whenever ground wires are removed during servicing these ground wires must be reconnected to ensure that the tumbler is properly grounded Monthly Bi Annually 1 Remove lint and debris from inside exhaust duct 1 Check mounting hardware for any loose nuts to maintain proper airflow and avoid bolts or screws overheating 2 Check gas connections for leakage a Remove external duct and duct access covers if present b Clean inside of duct with a vacuum 4 a A connections for looseness and Check
14. ndry Systems LLC DO NOT COPY or TRANSMIT 70269501 Before You Call for Service Won t Start Won t Heat Clothes Not Dry Possible Reason Corrective Actions Insert correct coin s or valid card if applicable Close the loading door tightly Close lint panel tightly Press the PUSH TO START button Be sure power cord is plugged all the way into the electrical outlet Drying timer is in OFF position Check the main fuse and circuit breaker Check fuses located in the machine Insufficient airflow Gas shut off valve in OFF position Are controls properly set Broken drive belt Call the service person Tumbler is in Cool Down Mode Lint screen clogged Clean lint screen Exhaust duct to outside is blocked Clean out Customer Service If literature or replacement parts are required contact the source from which the machine was purchased or contact Alliance Laundry Systems at 920 748 3950 for the name and address of the nearest authorized parts distributor For technical assistance call 920 748 3121 70269501 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 27
15. o gas tumbler before servicing e Close steam valve to steam tumbler before servicing e Never start the tumbler with any guards panels removed e Whenever ground wires are removed during servicing these ground wires must be reconnected to ensure that the tumbler is properly grounded Daily Maintenance Inspect the area surrounding tumblers remove all combustible materials including lint before operating the machine Check cylinder for foreign objects to avoid damage to clothing and equipment Clean lint from lint compartment and screen to maintain proper airflow and avoid overheating Monthly Maintenance Remove lint and debris from inside exhaust duct to maintain proper airflow and avoid overheating Ensure even lint distribution over lint screen Replace if distribution of lint is uneven to maintain proper airflow and avoid overheating Carefully wipe any accumulated lint off the cabinet high limit thermostat and thermistor including perforated cover Lint buildup will act as an insulator causing machine to overheat Clean lint and debris buildup from blower to maintain proper airflow to avoid overheating and prevent possible vibration 24 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 70269501 Maintenance To reduce the risk of electric shock fire explosion serious injury or death e Disconn
16. ogramming Manual IMPORTANT If the loading door or lint panel door is opened during the cycle the heating system NOTE Do not press directly on lights or the center of pad For proper selection press on pad slightly to the right of center Refer to Figure 7 AES TMB806N Figure 7 70269501 will shut off and the motor will stop To restart the cycle both doors must be closed and the PUSH TO START button must be pressed in 3 When the cycle is complete open door and remove the laundry Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 15 Operating Instructions 1 2 SELECT INSERT TEMP COINS CARD DRYING COOL DOWN HIGH LOW we temp 4 START MED zur DELIcATEs TMB1964N Figure 8 MDC Coin Control IMPORTANT To stop the tumbler at any time during the cycle OPEN DOOR To restart the BC and BX Control Suffixes tumbler CLOSE door and press START pad 1 Select HIGH TEMP MED TEMP LOW TEMP or DELICATES by pressing the appropriate temperature pad 2 Insert the coin s in the coin slot 3 Press START pad to start tumbler 16 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 4 When the cycle is complete open door and remove the laundry 70269501 Operating Instructions L__Je DRYING COOL DOWN INSERT CARD HERE HIGH LOW non temp 4 START MED 1 O cures TMB196
17. ons that you understand and have the skills to carry out Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product To reduce the risk of fire DO NOT DRY plastics or articles containing foam rubber or similarly textured rubberlike materials Always clean the lint filter daily Keep area around the exhaust opening and adjacent surrounding area free from the accumulation of lint dust and dirt Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 14 18 20 21 22 The interior of the tumbler and the exhaust duct should be cleaned periodically by qualified service personnel If not installed operated and maintained in accordance with the manufacturer s instructions or if there is damage to or mishandling of this product s components use of this product could expose you to substances in the fuel or from fuel combustion which can cause death or serious illness and which are known to the State of California to cause cancer birth defects or other reproductive harm Tumbler will not operate with the loading door open DO NOT bypass the door safety switch to permit the tumbler to operate with the door open The tumbler will stop tumbling when the door is opened Do not use the tumbler if it does not stop tumbling when the door is opened or starts tumbling without pressing or turning the START mechanism Remove the tumble
18. orm the reader of specific procedures where minor machine damage will occur if the procedure is not followed NOTE The word NOTE is used to communicate installation operation maintenance or servicing information that is important but not hazard related 70269501 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT IMPORTANT Warranty is void unless tumbler is installed according to instructions in the Installation Manual Compliance with minimum specifications and requirements detailed herein and with applicable local gas fitting regulations municipal building codes water supply regulations electrical wiring regulations and any other relevant statutory regulations Because of varied requirements applicable local codes should be thoroughly understood and all pre installation work arranged for accordingly Failure to install maintain and or operate this machine according to manufacturer s instructions may result in conditions which can produce serious injury death and or property damage WO51R1 NOTE The WARNING and IMPORTANT instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur It must be understood that common sense caution and carefulness are factors which CANNOT be built into this tumbler These factors MUST BE supplied by the person s installing maintaining or operating the tumbler Always contact your dealer distrib
19. r from use and call for service Tumbler will not operate with lint panel open DO NOT bypass lint panel safety switch to permit the tumbler to operate with the lint panel open Do not put articles soiled with vegetable or cooking oil in the tumbler as these oils may not be removed during washing Due to the remaining oil the fabric may catch on fire by itself To reduce the risk of fire DO NOT put clothes which have traces of any flammable substances such as machine oil flammable chemicals thinner etc or anything containing wax or chemicals such as in mops and cleaning cloths or anything dry cleaned at home with dry cleaning solvent in the tumbler Use the tumbler only for its intended purpose drying fabrics ALWAYS disconnect and lockout the electrical power to the tumbler before servicing Disconnect power by shutting off appropriate breaker or fuse Install this tumbler according to the INSTALLATION INSTRUCTIONS All connections for electrical power grounding and gas supply must comply with local codes and be made by licensed personnel when required 70269501 23 24 25 26 27 28 70269501 Remove laundry immediately after tumbler stops Always read and follow manufacturer s instructions on packages of laundry and cleaning aids Heed all warnings or precautions To reduce the risk of poisoning or chemical burns keep them out of reach of children at all times preferably in a locked ca
20. ry DO NOT OVERLOAD NOTE Overloading causes slow drying and wrinkling Close loading door Tumbler will not operate with the door open Step 3 Determine Control Type and Temperature Setting Refer to the various controls pages 12 19 and follow instructions for the appropriate control type T30 models only use the correct coin slot and control panel for the top or bottom cylinder The type of fabric being dried will determine the setting Consult the fabric care label or fabric manufacturer to determine proper temperature setting IMPORTANT Always follow the fabric care instructions supplied by the garment manufacturer Step 4 Remove Laundry When the cycle is complete open door and remove the laundry Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 11 Operating Instructions TEMPERATURE K Low PUSH TO H START z T 8 SELECT RT PUSH TEMP com stany gt INSERT QUARTER TURN KNOB Uanrepms TMB807N Figure 3 Electromechanical Coin Control CD CX and CY Control Suffixes 1 Set the TEMPERATURE selector at HIGH or LOW or anywhere between these settings 2 Coin Drop Models Insert the coin s in the coin slot turn the knob to the right and release it 3 Press the PUSH TO START button and hold it for approximately three 3 seconds 12 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT NOTE Addi
21. stop the tumbler at any time f during the cycle OPEN DOOR To restart the NR NY ZR and ZY Control Suffixes tumbler CLOSE door and press START pad 1 Select HIGH TEMP MED TEMP LOW TEMP 4 When th 1 let d d or NO HEAT by pressing the appropriate a 3 Bea US RE temperature pad 2 Insert card into opening DO NOT remove the card until REMOVE CARD LED is lit 3 Press START pad to start tumbler 70269501 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 19 Notes 20 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 70269501 Maintenance To reduce the risk of electric shock fire explosion serious injury or death e Disconnect electric power to the tumbler before servicing e Close gas shut off valve to gas tumbler before servicing e Close steam valve to steam tumbler before servicing e Never start the tumbler with any guards panels removed e Whenever ground wires are removed during servicing these ground wires must be reconnected to ensure that the tumbler is properly grounded Daily c Be sure the lint screen is not torn If it is replace immediately A torn lint screen allows 1 Inspect the area surrounding tumblers remove all lint to pass from the tumbler to the ductwork combustible materials including lint before system thus creating a restriction to air operating
22. the Temperature selector at HIGH LOW or anywhere between these settings Press the PUSH TO START button in and hold it in for approximately three seconds This starts the tumbler cycle IMPORTANT If the door is opened during the cycle the heating system will shut off and the motor will stop To restart the cycle door must be closed and the PUSH TO START button must be pressed in 5 When the cycle is complete open door and remove the laundry Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 70269501 Operating Instructions STATUS PROGRAM DRYING AUTO TIME oF OG Q Wes IGS Tew SOWN JL IQD ERM a TD w STOP RESET OK TEMP DISPLAY OF a FIC O SIGNAL CUSTOM OX D O CONDITION TMB1789N Figure 6 Electronic OPL Control OM Control Suffix 1 To use an Automatic Cycle press an ON SELECT pad Select HIGH MEDIUM MED LOW LOW or NO HEAT for items that should not be dried with heat A light to the left of the selected pad lights up 2 Press START pad to start tumbler NOTE All pads can be pressed in any sequence without damaging control or tumbler To stop the tumbler at any time open the door or press STOP RESET The window display will flash Press STOP RESET twice within 3 seconds to end the cycle and reset the control to idle status To restart the tumbler CLOSE door and press START pad To use a Time Dry or Custom Cycle refer to the Pr
23. the machines circulation 2 Check cylinder for foreign objects to avoid d The lint screen is designed to completely damage to clothing and equipment cover the entire opening in the lint screen panel Be sure that it does so Excessive gaps between the lint screen and the lint screen panel allow lint to pass into the ductwork system 3 Clean lint from lint compartment and screen to maintain proper airflow and avoid overheating WARNING To reduce the risk of serious injury do not open the lint panel while the tumbler is in e Carefully wipe any accumulated lint off of the cabinet high limit thermostat and thermistor Failure to do so will allow a buildup of lint in this area to act as an insulator causing the tumbler to overheat Refer to Figure 12 operation Before cleaning the lint screen open tumbler door and allow cylinder to completely stop f Replace the lint compartment panel on the tumbler ensuring a tight fit and lock if applicable a Open the lint panel or pull out lint drawer b Remove all accumulated lint in the lint compartment area Lightly brush any lint that may be left on the lint screen Lint left in the lint compartment is drawn back onto the lint screen and will restrict proper air circulation 70269501 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 21 Maintenance To reduce the risk of electric shock fire explosion serious injury or death e Disconnect electr
24. tional drying time may be purchased at cycle start or while tumbler is running by adding additional coin s IMPORTANT If the loading door or lint panel door is opened during the cycle the heating system will shut off and the motor will stop However the timer will continue to run To restart the cycle both doors must be closed and the PUSH TO START button must be pressed in 4 When the cycle is complete open door and remove the laundry 70269501 Operating Instructions sucer N so T3611 Figure 4 Electronic Coin Control NOTE Additional drying time may be purchased at cycle start or while tumbler is running b EC EX and EY Control Suffixes adding additional coin s EX I en ae peek a LOW TENU IMPORTANT To stop the tumbler at any time or pressing the appropriate during the cycle OPEN DOOR To restart the temperature pad tumbler CLOSE door and press START pad 2 Insert the coin s in the coin slot i 4 When the cycle is complete open door and 3 Press START pad to start tumbler remove the laundry 70269501 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 13 Operating Instructions TMB47N Figure 5 Manual Timer MT Control Suffix 1 14 Set the HEAT Drying timer for the number of minutes from 0 60 desired Set the COOL DOWN Cooling timer for the number of minutes from 0 15 desired Set
25. utor service agent or the manufacturer on any problems or conditions you do not understand Safety Information Important Safety Instructions Save These Instructions Hazardous Voltage Can cause shock burn or cause death Allow machine power to remain off for two minutes prior to working in and around AC inverter drive W359 Read all instructions before using the tumbler Refer to the GROUNDING INSTRUCTIONS for the proper grounding of the tumbler Do not dry articles that have been previously cleaned in washed in soaked in or spotted with gasoline dry cleaning solvents other flammable or explosive substances as they give off vapors that could ignite or explode Do not allow children on or in the tumbler This appliance is not intended for use by young children or infirm persons without supervision Young children should be supervised to ensure that they do not play with the appliance Before the tumbler is removed from service or discarded remove the door to the drying compartment and the door to the lint compartment Do not reach into the tumbler if the cylinder is revolving Do not install or store the tumbler where it will be exposed to water and or weather 8 Do not tamper with the controls 10 11 12 13 Do not repair or replace any part of the tumbler or attempt any servicing unless specifically recommended in the user maintenance instructions or in published user repair instructi
Download Pdf Manuals
Related Search