Alliance Laundry Systems 201959R1 Washer User Manual
Contents
1. Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Washer Symptom Possible Cause Solution Water Leaks Check that fill hoses are properly installed on the faucets and the washer s water mixing valve Replace the fill hoses every five years e Make sure drain receptacle is not clogged Check house plumbing Laundry load may be oversudsing or overloaded Use less detergent or low sudsing detergent and proper load sizes Is Noisy Wash load may be unbalanced Open lid and redistribute the load o ake sure washer is level Uneven leveling can cause vibration Anewly installed washer may make a knocking sound if the machine has been in storage The belt may have settled Run washer through 4 5 cycles to loosen belt Washer operation will not be affected Load Is Too Wet Wash load may be unbalanced Open lid and redistribute the load Load is too small Add items to make full load Make sure the correct spin speed is selected for the type of items being washed if option is available on your model Wrong Water Temperature e Make sure that the controls are properly set Check fill hoses Make sure hot faucet hose is connected to hot mixing valve indicated with H on the valve bracket and cold faucet is connected to cold mixing valve indicated with C on the valve bracket e Make sure house water heater is adjusted properly 21 201959 Copyright Alliance Laundry Sy2. fabric wear wrinkling and provides for a clean wash On this cycle the agitation during the wash portion of the cycle is not constant The wash will alternate between a period of agitation and a period of pausing This continues until advancing to the spin portion of the cycle There are two settings in the DELICATE cycle Normal and Light On some models the number shown next to these settings is the length of time in minutes For example Setting the timer on Normal will be nine minutes including short periods of agitation and long periods of soaking Soak Prewash on select models only Use for heavily soiled or stained clothing During the SOAK PREWASH setting the washtub will fill with water agitate for a reduced period of time pause for approximately 12 minutes and spin out to complete the cycle 201959 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT To Wash Clothes 3 Add clothes loosely into the washtub IMPORTANT Before using your new washer make sure the washer cord is plugged into a 120 Volt electrical outlet that has the proper grounding NF l and polarity Make sure the washer hoses are connected to the hot and cold water faucets and that the faucets are turned on Be sure the drain hose is not kinked and is inserted into a drain Refer to the INSTALLATION INSTRUCTIONS for details of proper washer installation TLW1996N IMPORTANT Prior to first wash use an all purp
3. pillowcases bottom end of t shirts etc If this portion is white and center is yellow the fabric contains unremoved soil Use sufficient detergent and a hot wash Chlorine bleach may be needed Clothes Stained From lron in the Water To test if an iron stain use a rust remover on a portion of the garment Follow bottle directions for larger items Older Clothes Some white fabrics turn yellow with age and cannot be whitened Clothes Tearing or Damaged Improper Use of Chlorine Bleach No correction for bleach damaged clothes Always measure and dilute bleach Take extra care to avoid unwanted spilling Overcrowding or Overloading Make sure all items can move freely during agitation Insufficient Precare Fasten all hooks and zippers Mend tears Remove objects from pockets continued 15 201959 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Problem Cause Solution Excessive Lint mproper Sorting Fabrics which shed lint cannot be washed with fabrics that receive lint nsufficient Detergent Use enough detergent so lint remains suspended in water and on phosphate Detergent flushed out ixing Fabric Types Knits and Fermanent Press attract lint Wash these only with similar items Use fabric softener in rinse water Wrinkling proper Sorting Heavy items like towels should not be washed with light items like nightgowns Too Many Clo
4. the size of your wash load Small loads will use lower water levels There must be enough water in the washtub to allow items to move and turn over freely may remain after washing and may cause the fabric to catch on fire by itself Loading the Washer Wrong Water Level for Size of Load Right Water Level for Size of Load NOTE Always add detergent first Load Articles Load items by the amount of space they take up not by their weight Mix large and small items in a load to get the best washing results TLW1993N Drop items loosely into the washtub The bulk of the clothes rather than the weight will determine load size Do not pack items in or wrap them around the agitator Overloading can cause poor cleaning excessive wrinkling and tears Overloading the washtub can result in poor washing and rinsing Overloading may also cause wrinkling and tearing of items IMPORTANT If in doubt always use a higher water level Most average loads will require a water setting between Medium and Extra Large Failure to have the correct volume of water relative to the load will increase the incidence of excessive lint e Reset OPTIONAL Use the RESET if agitation has started and more water is needed for the load TLW1992N e Items should move freely through the wash water for best cleaning results Items should rollover sink and then reappear Load Sizes Mini Select Models 1 2 perman
5. water is less effective in cleaning than hot or a are warm water but it does minimize wrinkling and color fading Use it for washing extra sensitive clothes re oe WARM and for the rinsing of all fabrics 37 C he NOTE In wash temperatures colder than 60 F 15 C detergents do not dissolve well This may 60 F COLD cause ineffective cleaning or lint and residue to 15 C form TLW1994N Wash Temperature Guide Water Temperature Use Comments HOT Sturdy whites and colorfast items Best cleaning for heavily soiled approximately 120 F 49 C Work clothes items as determined by outside water Soiled items Best for sanitizing supply Diapers WARM Light and moderately soiled items Reduces wrinkling in permanent approximately 100 F 37 C as determined by outside water supply Fermanent press Non colorfast or dark colors Silks woolens nylon acrylic press fabrics Less fading Reduces shrinking in knits COLD approximately 60 F 15 C as determined by outside water supply Non colorfast fabrics Rinsing of most items Extra sensitive clothing Saves energy Reduces color fading Reduces wrinkling Reduces shrinking NOTE Some models regulate the hot and warm temperatures to save energy costs In these models hot water is approximately 102 F 39 C and warm water is approximately 80 F 26 C 201959 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Operatin
6. COPY or TRANSMIT Install the washer according to the Installation Instructions All connections for water drain electrical power and grounding must comply with local codes and be made by licensed personnel when required Do not do it yourself unless you know how To reduce the risk of fire clothes which have traces of any flammable substances such as vegetable oil cooking oil machine oil flammable chemicals thinner etc or anything containing wax or chemicals such as in mops and cleaning cloths must not be put into the washer These flammable substances may cause the fabric to catch on fire by itself Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product Keep your washer in good condition Bumping or dropping the washer can damage safety features If this occurs have your washer checked by a qualified service person Replace worn power cords and or loose plugs Be sure water connections have a shut off valve and that fill hose connections are tight CLOSE the shut off valves at the end of each wash day Replace fill hoses every five years Lid MUST BE CLOSED any time the washer is to agitate or spin DO NOT by pass the lid switch by permitting the washer to agitate or spin with the lid open A brake will stop the washtub within seconds if the lid is opened during spinning If the washtub does not stop when the lid is opened remove the wash
7. abric softener The fabric softener will remain in the dispenser during the wash fill agitation and spin At the end of the wash spin the liquid fabric softener will be dispensed into the washtub through the slots in the agitator and will be mixed with the incoming rinse water 201959 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT To Clean the Dispenser Remove the dispenser housing from agitator by squeezing the lower part of the dispenser pulling directly upward and at the same time tilting slightly This will expose the dispenser cup which is also removable for cleaning refer to illustration Both housing and cup can be soaked in hot soapy water and rinsed clean The funnel shape in top of agitator also needs to be cleaned The hole and the slots in the two rings will require using a small brush for proper cleaning After cleaning install dispenser cup then push dispenser housing directly downward onto top of agitator until firmly snapped together if TLW2001N 14 Use Tips Fabric softener spilled onto garments may cause staining To remove dampen stain and rub with bar soap Wash as usual Liquid fabric softeners will be dispensed during the final rinse and should not be combined with bleach bluing starch detergents soaps or packaged water conditioners Fabric softener is not to be used in dispenser when using Prewash cycle if available When adding detergent to wa
8. asher automatically Won t Agitate ake sure lid is closed ull timer knob out to start washer ake sure power cord is plugged all the way into the electrical outlet Check the house fuse or circuit breaker The motor overload protector may have stopped the cycle It will reset itself in two or three inutes and restart the washer automatically Broken drive belt Call the service person AY Won t Spin Make sure lid is closed Pull timer knob out to start washer o ake sure power cord is plugged all the way into the electrical outlet Check the house fuse or circuit breaker The motor overload protector may have stopped the cycle It will reset itself in two or three minutes and restart the washer automatically e Broken drive belt Call the service person Stops Pauses During Cycle Pauses are part of the washer s normal operation The washer will stop pause shortly before the wash and rinse spins Check the house fuse or circuit breaker The motor overload protector may have stopped the cycle It will reset itself in two or three minutes and restart the washer automatically DY Won t Drain Make sure drain hose is not kinked or twisted Make sure drain hose is not clogged e Make sure drain receptacle is not clogged e Refer to the Installation Instructions to make sure that the drain hose has been properly installed 20 201959 Copyright
9. ations that may occur Observe and be aware of other labels and precautions that are located on the machine They are intended to provide instructions for safe use of the machine Common sense caution and care must be exercised when installing maintaining or operating the washer Always contact your dealer distributor or service agent about any problems or conditions you do not understand 201959 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Operation Before Washing Prepare Wash Load Empty Pockets and Cuffs Make sure all pockets are empty and turn them inside out One bobby pin metal or plastic toy nail or sharp object in a load can catch laundry and cause tears Facial tissue left in a pocket will produce extreme lint A crayon or lipstick in a wash load may cause stains that cannot be removed Roll down cuffs and shake out grass sand and gravel Mend Rips and Tears Little holes can become bigger in the washer Mend holes and tears before placing garments in the washer Close Zipper and Fasten Hooks These can catch on garments in a wash load and tear them Tie belts and sashes so they won t wind around clothes Check For Colorfastness Squeeze a portion of garment in warm or hot sudsy water If the color bleeds or runs wash the item separately in cold water Sort Items Different items use different wash cycles and temperatures Always follow the manufacturers care label Pr
10. d other natural parts deteriorate after extended use Hoses may develop cracks blisters or material wear from the temperature and constant high pressure they are subjected to All hoses should be checked on a monthly basis for any visible signs of deterioration Any hose showing the signs of deterioration listed above should be replaced immediately All hoses should be replaced every five years Vacations and Extended Non Udse To avoid possible property damage due to flooding turn off the water supply to the washer whenever there will be an extended period of non use Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Reinstallation of Shipping Materials You must install the shipping brace and shipping plug any time the washer is moved Shipping Brace The shipping brace in the lid opening should be saved and reinstalled whenever the washer is moved To reinstall the brace open the washer lid and place the brace over the washer agitator placing the back of the brace into the washtub first Shipping Plug The plastic shipping plug should be saved and reinstalled any time the washer is moved The plug fits into two openings The base opening and the shipping plug opening on the bottom of the mobile pivot dome The plug MUST be inserted into both openings to prevent damage to the washer In order to accomplish this the shipping plug opening must be directly lined up with the base op
11. e proper Indicates a hazardous situation that if grounding of the washer not avoided could cause severe A l personal injury or death 3 Donot wash articles that have been previously cleaned in washed in soaked in or spotted with gasoline dry cleaning solvents or other flammable or explosive substances as they A CAUTION give off vapors that could ignite or explode 4 Do not add gasoline dry cleaning solvents or other flammable or explosive substances to the wash water These substances give off vapors that could ignite or explode Indicates a hazardous situation that if not avoided may cause minor or moderate personal injury or property damage Additional precautionary statements CIMPORTANT and NOTE are followed by specific instructions IMPORTANT The word IMPORTANT is used to inform the reader of specific procedures where minor machine damage will occur if the procedure is not followed Copyright 2010 Alliance Laundry Systems LLC All rights reserved No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher 3 201959 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT a 10 11 T2 15 14 Under certain conditions hydrogen gas may be produced in a hot water system that has not been used for two weeks or more HYDROGEN GAS I9 EXPLOSIVE If the hot wat
12. ening Refer to illustrations below Shipping Brace Shipping Plug Opening TLW2044N Opening 201959 After the shipping brace has been installed in the lid opening tilt washer back enough to access base opening Insert shipping plug into base opening and using the palm of your hand push shipping plug into washer until it snaps into shipping plug opening Motor Overload Protector e The internal motor overload protector will stop the motor automatically if there are too many clothes in the washtub or if a failure has occurred within the machine The overload protector will reset itself in two or three minutes and the motor will restart automatically lf the overload protector stops the motor again remove the washer from use and call the service person to correct the problem Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Preventative Maintenance Follow these guidelines to ensure the washer operates properly Call for service if you observe any of the following water of any amount on the floor an increase in operating noise or water remaining in the washtub after a cycle Frequency Maintenance Procedure Monthly 1 Check all hoses and the drain for leaks 2 Check the lid switch for proper operation 3 Check to make sure the washer is level Every six months Clean the filter screen in the fill hoses Every five years Have a qualified se
13. ent press dress shirts or 2 pillow cases or 1 lightweight dress or similar size load Small 3 4 permanent press dress shirts or 1 twin sheet 1 pillow case or 1 2 lightweight dresses Medium 6 7 permanent press shirts or 2 twin sheets 2 pillow cases or amp standard bath towels 6 wash cloths Extra Large amp 9 shirts 5 pair polyester pants or 2 queen size sheets 4 pillow cases 2 nightgowns 1 pair men s pajamas or 1 queen size bedspread 7 201959 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Wash Temperature Hot Water Hot water will give the best results of cleaning and sanitizing but it is not suitable for all items It is best for sturdy whites and colorfast items heavily soiled items and diapers Warm Water By using warm water there is less chance of color loss in items Warm water also reduces wrinkling in permanent press items Use with light and moderate soils non colorfast or dark colors Energy You can save energy when washing by following a few guidelines 1 Heating water accounts for the greatest energy expense when washing Save on heating water by using warm or cold washes as well as cold rinses 2 Wash full loads but do not overload Use soak cycles for heavily soiled items to reduce wash times 4 Select a shorter wash time for lightly soiled permanent press silks woolens nylon and acrylic items Cold Water A o Cold
14. er from use and call the service person Check washer for water leaks after each use If water is found turn off the water supply and call for service immediately Don t use washer until it is repaired by an authorized service agent 25 24 25 26 ZT 28 29 30 51 If the washer s volume or type of sound changes from what is normally heard call an authorized service agent immediately to prevent possible damage to other components Never start a cycle and leave the property without first checking to make sure the wash cycle is complete Always read and follow manufacturer s instructions on packages of laundry and cleaning aids Heed all warnings or precautions To reduce the risk of poisoning or chemical burns keep them out of the reach of children at all times preferably in a locked cabinet Always follow the fabric care instructions supplied by the garment manufacturer Never operate the washer with any guards and or panels removed DO NOT operate the washer with missing or broken parts DO NOT by pass any safety devices Failure to install maintain and or operate this machine according to the manufacturer s instructions may result in conditions which can produce bodily injury and or property damage Replace washer fill hoses every five years 5 NOTE The WARNING and Important Safety Instructions appearing in this manual are not meant to cover all possible conditions and situ
15. er system has not been used for such a period before using a washing machine or combination washer dryer turn on all hot water faucets and let the water flow from each for several minutes This will release any accumulated hydrogen gas THE GAS S FLAMMABLE DO NOT SMOKE OR USE AN OPEN FLAME DURING THIS TIME Close supervision of children is necessary when the washer is used near children This is a safety rule for all appliances Before the washer is removed from service or discarded remove the lid to the washing compartment Do not reach into the washer if the washtub or agitator is moving Do not install or store the washer where it will be exposed to water and or weather Do not tamper with the controls Do not repair or replace any part of the washer or attempt any servicing unless specifically recommended in the user maintenance instructions or in published user repair instructions that you understand and have the skills to carry out To reduce the risk of an electric shock or fire DO NOT use an extension cord or an adapter to connect the washer to the electrical power source Use your washer only for its intended purpose washing clothes ALWAYS disconnect the washer from electrical supply before attempting any service Disconnect the power cord by grasping the plug not the cord TS 16 TZ 18 T2 20 21 VES 4 201959 Copyright Alliance Laundry Systems LLC DO NOT
16. g Your Washer Al warna To reduce the risk of fire electric shock serious injury or death to persons read the Safety Information section before operating your washer W522 Determine Proper Cycle Some cycles may not be included on your model Regular Cycle Use for sturdy items like play or work clothes towels T shirts etc The wash time selection will depend on the type of fabric and the amount of soil For the best results when cleaning heavily soiled items use a longer wash time 15 minutes maximum Lightly soiled items require less wash time and spin out There are three settings in the REGULAR cycle Extra Clean Normal and Light On some models the number shown next to these settings is the length of agitation in minutes For example Setting the timer on Extra Clean will be a 15 minute agitation Permanent Press Cycle Use for permanent press items and synthetics The wash time selection will depend upon the type of fabric and amount of soil There are two settings in the PERMANENT PRESS cycle Normal and Light On some models the number shown next to these settings is the length of agitation in minutes For example Setting the timer on Normal will be a nine minute agitation Delicate Cycle Wash delicate items usually washed by hand on this cycle A full tub of water is recommended even for small loads to allow the delicate items to move freely through the water More water helps reduce
17. ll result in the washer overflowing and cause property damage W524 201959 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Optional Features Bleach Dispenser The bleach dispenser is located in the left front corner under the lid Use liquid bleach in the dispenser Fowdered bleach must not be used in the dispenser Add powdered bleach to the wash water Use no more than one cup chlorine bleach for large loads three quarters cup for medium and one half cup for small loads Carefully pour recommended amount of bleach into the dispenser during the first fill of the washer Be careful not to spill undiluted bleach It is a strong chemical and can damage some fabrics if it is not properly diluted 13 Fabric Softener Dispenser To Use Dispenser After the clothes are loaded into the washtub and before the start of the WASH cycle pour the proper amount of liquid fabric softener into the bottle measuring cap refer to bottle directions Four into dispenser The large fabric softener dispenser allows for the fabric softener to be diluted with water We recommend adding water up to the fill level Do not exceed tip of arrow which indicates correct fill level Over filling can allow fabric softener to spill onto the clothes causing stains on clothes if the softener comes into contact with detergent suds Setting the water level to medium or higher will result in better performance from the f
18. oper sorting is easy if you follow a few guidelines 1 Sort by Color Separate items into loads of whites darks lights and non colorfast 2 Sort by Fabric and Construction Separate items into loads of Cottons cottons linens permanent press ASA synthetics blends poly knits and A delicates cs TLW1991N h 990N 5 Sort by Temperature Separate items into loads that can be washed in cold warm or hot water 4 Sort by Type and Amount of Soil Heavily soiled clothes will need extra treatment Lightly soiled clothes can become dingy if washed with heavily soiled items 5 Sort Lint Shedders From Lint Receivers Some fabrics attract lint and should not be washed with lint shedding loads Lint shedders are cottons terry towels chenille bedspreads rugs and clothes that have been heavily bleached Lint receivers are synthetics permanent or durable press knits including socks corduroy and other smooth fabrics Pretreat Pretreat shirt collars and cuffs with a pretreat product or liquid detergent when placing them in the washer Before washing treat special stains individually 201959 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT e When washing very large items do not fill yN WARNING washtub as full as with other loads Do not wash or dry items soiled with Water Level vegetable or cooking oils Some oils The water level in your washer should fit
19. ose cleaner or a detergent and water solution and a damp cloth to remove shipping dust from inside of washtub 4 Close the lid The washer will not agitate or spin with the lid open 1 Get the clothes ready for washing Empty pockets and cuffs Sort items into separate loads Pretreat stains and heavily soiled areas TLW1997N A WARNING TLW1991N To reduce the risk of serious injury do not by pass the lid switch by permitting the washer to agitate or spin with the lid open IMPORTANT Remove all sharp objects from laundry to avoid tears and rips to items during normal machine operation we 2 Measure and add detergent to the washtub Follow instructions on detergent package for amount to use TLW1995N 10 201959 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 5 Set WASH RINSE temperatures WASH RINSE TEMP WARM HOT COLD COLD COLD COLD ENERGY SAVER TLW2080N 7 Select the cycle according to the type of fabric being washed Push the timer knob in and turn clockwise to the desired cycle and wash time Pull the timer knob out to start the water fill Agitation will begin when the water reaches the level you selected NOTE Lid must be closed for agitation and spin to start The washer will stop pause shortly before the wash and rinse spins Do not turn the timer through these pauses They are part of the cycle The Ene
20. rgy Saver settings marked with an asterisk show which temperature settings will use the least energy 6 Set LOAD SIZE WATER LEVEL control Use RESET if agitation has started and more water is needed MINI setting is on select models LOAD SIZE MEDIUM SMALL z EX be LRG RESET IMPORTANT Holding the LOAD SIZE WATER LEVEL control in the RESET position can cause flooding of the washer 11 201959 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Timer Although the washer cycles are automatic the timer may be reset to lengthen shorten or repeat a portion of a cycle To set or reset the timer push timer knob in to stop the washer Hold timer knob in firmly while turning it clockwise to the setting desired Pull timer knob out to start the washer Manual Soaking Set the timer knob in the center of the word RINSE this prevents the washer from spinning without first filling with water Place the soaking product and clothes load in the washtub Pull timer knob to start washer fill After fill is completed and agitation has started lid must be closed push the timer knob in This will stop the washer When the clothes have soaked the desired length of time TURN THE TIMER KNOB TO THE START OF THE SPIN SETTING then pull the timer knob out to start the spin Al canon Failure to turn the timer knob to the spin cycle and completely drain the washtub after soaking wi
21. rvice technician conduct general preventative maintenance on the washer to ensure it operates properly 19 201959 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Troubleshooting Try these troubleshooting tips before making a service call You may save time and money Washer Symptom Possible Cause Solution Won t Fill ake sure power cord is plugged all the way into the electrical outlet ake sure hot and cold water faucets are turned on ake sure that the fill hoses are not kinked or twisted Pull timer knob out to start washer e Make sure that the controls are properly set Make sure that the last spin has been completed Check the house fuse or circuit breaker Clean the screens in the water mixing valve and the filter screens located at the faucet end of the fill hoses Owner is responsible for service calls regarding cleaning of the screens Water is being siphoned from the washer during the cycle Refer to the Installation structions to make sure that the drain hose has been properly installed Won t Start e Make sure lid is closed e Pull timer knob out to start washer e Make sure power cord is plugged all the way into the electrical outlet e Make sure that the controls are properly set Check the house fuse or circuit breaker The motor overload protector may have stopped the cycle It will reset itself in two or three minutes and restart the w
22. sh water do not allow any to enter into softener dispenser cup as softener will become gummy To prevent softener buildup the dispenser can be filled with clean water for automatic cleaning This can be done in washing cycles other than when softener is used Agitator Cap IMPORTANT If your washer comes with an agitator cap the cap must be on at all times 201959 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Clothing Care Clothing Concerns To keep clothes looking white or bright use good build up of soil or water hardness minerals on them If you notice that your clothes are not as bright as they should be take corrective measures washing practices at all times to prevent a gradual immediately Problem Cause Solution Gray or Dingy Insufficient Detergent Add more detergent to washtub before loading clothes Mild Clothes detergents are not suitable for average soil Improper Sorting Wash whites separately Separate light from heavily soiled items Clothes can pick up soil from dirty wash water Nonphosphate Detergent and Hard Water Follow package directions Soften water if possible Water Not Hot Enough White clothes will stay whiter with hot wash water Increase temperature Overcrowding Washer Clothes must circulate freely through the water for best results Yellowed Clothes Unremoved Soil Skin soil is hard to remove Check hem edge of sheets and
23. stems LLC DO NOT COPY or TRANSMIT Contact Information If service is required contact the nearest Factory Authorized Service Center To find the nearest service center visit us online at www comlaundry com If you are unable to locate an authorized service center or are unsatisfied with the service performed on your unit contact Alliance Laundry Systems LLC Shepard Street P O Box 990 Ripon Wisconsin 54971 0990 www comlaundry com Phone 920 748 3121 Date Purchased Model Number Serial Number Model Number and Serial Number TLW2003N When contacting us about your washer PLEASE GIVE THE MODEL AND SERIAL NUMBERS The model and serial numbers are located on the nameplate The nameplate will be in the location shown Please include a copy of your bill of sale and any service receipts you have lf replacement parts are required contact the source from where you purchased your washer or visit us online at www comlaundry com AL Warnine To reduce the risk of serious injury or death DO NOT repair or replace any part of the washer or attempt any servicing unless specifically recommended in the user maintenance instructions or in published user repair instructions that you understand and have the skills to carry out 22 201959 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT
24. thes in Washer Clothes must circulate freely through the water for best results Improper Cycle ake sure cycle selected is appropriate for type of clothes Improper Temperature Using a warm or cold wash and a cold rinse reduces wrinkling 16 201959 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Maintenance Cold Weather Care If the washer is delivered on a cold day below freezing or is stored in an unheated room or area during the cold months do not attempt to operate it until the washer has had a chance to warm up Care of Your Washer Use only a damp or sudsy cloth for cleaning the control panel Some spray pretreat products may harm the finish on the control panel Wipe the washer cabinet as needed If detergent bleach or other washing products are spilled on the cabinet wipe immediately Some products will cause permanent damage if spilled on the cabinet Do not use scouring pads or abrasive cleansers The washtub will need no particular care though it may need rinsing or wiping after an unusual load has been washed This also may be necessary if too little detergent has been used Leave the lid open to allow the inside of the washer to dry out after use This helps prevent musty odors from developing Check the filter screens in the fill hoses for debris or damage at least once a year Clean or replace them if necessary 201959 17 Replacing Hoses e Hoses an
25. vide iF by A N A for your Inside Safety Information Operation Clothing Care Maintenance Troubleshooting A lliance Part No 201959R1 Laund ry Systems www comlaundry com November 2010 AL Warning For your safety and to reduce the risk of fire or an explosion do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance 2 201959 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Safety Information Explanation of Safety NOTE The word NOTE is used to communicate installation operation maintenance or servicing Messages information that is important but not hazard related Throughout this manual and on machine decals you will find precautionary statements DANGER WARNING and CAUTION followed by specific Important Safety Instructions instructions These precautions are intended for the personal safety of the operator user servicer and those maintaining the machine Al panor Save These Instructions AL warna To reduce the risk of fire electric shock serious injury or death to persons when using your washer follow these basic precautions Indicates an imminently hazardous situation that if not avoided will cause severe personal injury or death 1 Read allinstructions before using the washer WARNING 2 Refer to the Grounding Information in the Installation Instructions for th
Download Pdf Manuals
Related Search