Alliance Laundry Systems 135 Washer User Manual
Contents
1. CODEAMrAM M CA611 Owners Manual CAUTION Be certain that the vehicle is outdoors before using this or any re mote vehicle starting device A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs DO NOT remote start the vehicle if the car is garaged Your Remote Start Alarm System has many features and available options some of which are selected at time of installation Consult your installing dealer for options that may have been installed and are not listed ARMING THE SYSTEM 1 Turn the engine OFF exit the vehicle and close all doors hood and trunk 2 Press and release the Arm button of your transmitter one time The parking lights will flash once the siren will chirp once and the LED will begin to flash slowly confirming the system is armed If you have the optional door lock unlock circuit installed the doors will lock NOTE If the siren horn sounds 3 chirps then you have left a door trunk or hood ajar Simply close the opened entry point to provide full protection If the siren chirped 3 times sometime after arming the exclusive delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired Again closing the hood trunk or doors will correct the problem and you do not need to disarm the system to make the correction If the siren horn did not sound when arming then th2. channel 3 press and hold the trunk button of your transmitter for 4 seconds ADDITIONAL REMOTE FUNCTION CHANNEL 4 The system has an additional feature Channel 4 that can be connected to a number of different optional accessories To operate the accessory associated with channel 4 press and release the star button of your transmitter Note The channel 4 output will remain active for as long as the transmitter button is held Certain accessories may take advantage of the extended output capability of this channel Check with your installation center for operation of the accessory that may be connected to channel 4 CA 611 SYSTEM FUNCTIONS AT A GLANCE ALARM DASH MOUNTED LED INDICATORS RAPID FLASHING PASSIVE ARMING SLOW FLASHING ARMED OFF DISARMED ON SOLID VALET MODE 2 FLASH SOLID REMOTE START VALET MODE 3 FLASH PAUSE INTRUSION ZONE 3 2 FLASH PAUSE INTRUSION ZONE 2 1 FLASH PAUSE INTRUSION ZONE 1 ALARM SIREN HORN CHIRP INDICATION 1 CHIRP ARM 2 CHIRPS DISARMED 3 CHIRPS ARMING WITH ENTRY POINT OPENED 4 CHIRPS DISARM AFTER INTRUSION 5 CONTINUOUS TRIGGERED PANIC ALARM PARKING LIGHT INDICATIONS 1 FLASH 2 FLASH 3 FLASH CONTINUOUS FLASH ARM DISARM DISARM AFTER INTRUSION TRIGGERED PANIC REMOTE START SIREN HORN INDICATIONS 1 LONG 1 SHORT RF START COMMAND ISSUED IF SELECTED ON REMOTE START PARKING LIGHT INDICATIONS 1 FLASH RF START COMMAND ISSUED ON RUNNING UNDER REMOTE START CONT
3. code programmed has not been changed and the default override code of 11 is in the system s memory 1 Enter the vehicle and turn the ignition switch to the ON position NOTE The siren will sound 2 Within 5 seconds press and release the button 1 time 3 Within 5 seconds turn the ignition switch OFF then ON 4 Within 5 seconds press and release the button 1 time 5 Turn the ignition switch OFF then ON and start the vehicle NOTE If you have changed the programmed override code then substitute your Page 8 new code tenths for step 2 above and units for step 5 above ELIMINATING THE NORMAL ARM DISARM CHIRPS You can selectively eliminate the normal arm and disarm chirps by holding the transmitter button slightly longer when arming or disarming This will prevent the siren horn chirps for one arm or disarm cycle To eliminate the chirps permanently 1 Start with the valet switch in the OFF position 2 Turn the ignition switch ON then OFF 3 Within 10 seconds of turning OFF the ignition switch press and release the valet button 3 times 4 If the chirps were on before you started the siren horn will emit 2 short chirps indicating that the chirps are now off If the chirps were off before you started the siren horn will emit one short chirp indicating that the chirps are now on NOTE If the vehicle battery is disconnected then reconnected the system will return to the default setting of chirps ON Repe
4. security system can be disarmed without the use of the transmitter This is necessary since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails To bypass the alarm system 1 Open the vehicle door The alarm will sound 2 Turn the ignition key to the ON position 3 Within 5 seconds press and release the valet button The alarm system will stop sounding and enter the bypassed mode You can now start and operate the vehicle normally Typically this override mode is used only if the transmitter has become inoperative Programming Your Custom Override Code Unlike override switches easily found and defeated this security system allows you to program a personal override code offering a higher level of security To take advantage of this option consult your installation center for programming details The system comes from the factory with a pre programmed override code of 11 To change this default override code do the following Page 6 Disarm the system by use of the transmitter or by use of the emergency override sequence Turn the ignition switch to the ON position Within 10 seconds press and release the valet override button 3 times Within 10 seconds turn the ignition switch OFF ON OFF ON OFF ON The siren horn will sound and the lights will flash one time Within 10 seconds begin to enter your chosen 10ths digit by pressing and releasing the butt
5. sensor detected Check the vehicle for possible damage to the glass or body panels If the LED flashes 2 times pause 2 times pause etc then an intrusion attempt was made to open the hood trunk or by an accessory triggering device Check the vehicle for indications of forced entry to these openings If the LED flashes 3 times pause 3 times pause etc then an intrusion attempt was made to the vehicle doors Check all doors for indications of forced entry NOTE The LED intrusion warning indications are stored in the system s memory and will be erased when the ignition switch is turned on Page 5 VALET MODE The valet button allows you to temporarily bypass all alarm functions eliminating the need to hand your transmitter to parking attendants or garage mechanics When the system is in valet mode all alarm functions are bypassed however the remote panic feature remote door locks and remote start will remain operational Enter the vehicle and turn the ignition key to the ON position Press and hold the valet button until the LED turns on solid The system will remain in the valet mode To return to normal operation press and release the valet button any time the ignition is on NOTE Always remember to return the vehicle to the valet OFF position This will ensure that the vehicle remains protected at all times MANUALLY OVERRIDING YOUR SYSTEM USING THE VALET BUTTON FOR MANUAL OVERRIDE Your
6. the dash mounted LED does not begin to flash rapidly then you have left a door hood or trunk ajar Closing this entry point will allow the arming cycle will begin If any entry point is opened during the 30 second arming cycle arming will be suspended When all entry points are closed the arming cycle will begin again At the end of the 30 seconds the parking lights will flash once the siren will chirp once and the LED will begin to flash slowly confirming the system is armed If the siren horn did not sound when arming then the chirps have been turned off Refer to the section on Eliminating the normal Arm Disarm Chirps found on page 8 of this manual Passive door locking is a selectable feature If you have the optional door lock unlock circuit installed the doors may or may not lock passively depending upon the setup during installation PROTECTION WHILE THE SYSTEM IS ARMED Opening any protected entry point hood trunk or doors will cause the alarm to trigger immediately The siren horn will sound and the parking lights will flash for 30 seconds then stop and continue to monitor all protected entry points If the thief left the door opened the system will sound for six 30 second cycles then shut down isolate the triggered zone and continue to protect all other zones Whenever the system is armed the LED will slowly flash This serves as a visual deterrent to a potential thief The LED is a very low current light emitting dio
7. ROL IF SELECTED CONTINUOUS FLASH RUNNING UNDER REMOTE START CONTROL IF SELECTED 2005 Code Systems Inc CODEAURM Code Systems Inc Limited Lifetime Warranty Code Systems Inc CODE warrants to the ORIGINAL PURCHASER of this CODE vehicle security product the Product purchased from an authorized CODE dealer that except as provided below should this Product under normal use and conditions be proven defective in material or workmanship DURING THE LIFETIME OF THE VEHICLE IN WHICH IT WAS ORIGINALLY INSTALLED such defect s will be repaired or replaced at CODE s option without charge for parts directly related to repairs of the defect s Switches indicator lights and transmitter cases are similarly warranted to the original purchaser for a period of one 1 year from the date of purchase of the Product CODE accessories sold separately are covered by the applicable warranty accompany ing the accessory This warranty is non transferable non assignable and is voided when 1 the Product is removed from the vehicle in which it was originally installed or 2 the vehicle in which the Product was originally installed is transferred to another party This warranty does not apply to any product damaged by accident physical or electrical abuse improper installation alteration or use contrary to its intended function fire flood or other natural acts In order for the Product to be repai
8. at the above procedure to eliminate the arm disarm chirps REMOTE PANIC OPERATION The lock or unlock button on your transmitter also functions as a panic switch for use in emergency situations To use remote panic 1 Press and hold the lock or unlock button of the transmitter for 3 or more seconds and release The alarm will immediately sound 2 To stop the alarm press and hold the lock or unlock button of the transmitter again for 3 seconds If the button is not pressed the alarm will automatically stop after 30 seconds Also if any transmitter button other than the lock or unlock button is pressed and released the Panic mode will be turned off immediately The normal function of this transmitter button will be suspended during the Panic sounding period NOTE While in the Panic mode pressing and releasing the lock or the unlock buttons will if the option is installed lock and unlock the doors respectively While in the panic mode anytime the unlock button is pressed the panic feature will continue for the allotted 30 seconds however the security system will be disarmed allowing the vehicle to start Page 9 REMOTE STARTING THE VEHICLE Press and release the option button of your transmitter 2 times within 2 seconds to activate the remote start system The vehicle will start and remain running for the pre programmed 10 or 15 minutes As a visual indication the parking lights will flash or turn on depending
9. de L E D and will not cause the battery to drain even if left unattended for long periods of time Whenever the system is triggered the vehicle s parking lights will flash for the full siren horn sounding period Whenever the system is armed the vehicle starter circuit is disabled and the vehicle will not start with the ignition key Whenever the system is armed any strong impact to the vehicle will cause the shock sensor to trigger the alarm Any lesser impact will cause the pre detect stage of the shock sensor to emit a few short series of warning tones from the siren horn Page 3 DISARMING THE SYSTEM As you approach the vehicle press and release the Disarm button on the transmitter The parking lights will flash 2 times the siren horn will chirp 2 times and the LED will turn off If you have the optional door lock unlock circuit installed the doors will unlock If you have the optional entry illumination circuit installed the interior light will turn on for 30 seconds or until the ignition key is switched on NOTE If the passive arming mode was selected at time of installation the LED will start flashing rapidly indicating that the system is rearming Opening any door will suspend the automatic arming If the parking lights flashed 3 times and the siren horn chirps 4 times this indicates that the alarm system was triggered during your absence Before turning on the ignition key examine the LED flas
10. e chirps have been turned off and you should refer to the section titled ELIMINATING THE NORMAL ARM DISARM CHIRPS page 9 of this manual SILENT ARMING 1 Turn the engine OFF exit the vehicle and close all doors hood and trunk 2 Press and hold the Arm button of your transmitter for 2 seconds The parking lights will flash once and the LED will begin to flash slowly confirming the system is armed The siren will not chirp If you have the optional door lock unlock circuit installed the doors will lock NOTE If the siren horn sounds 3 chirps then you have left a door trunk or hood ajar Simply close the opened entry point to provide full protection If the siren chirped three times sometime after arming the exclusive delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired Again closing the hood trunk or doors will correct the problem and you do not need to disarm the system to make the correction If the siren horn did not sound when arming then the chirps have been turned off and you should refer to the section titled ELIMINATING THE NORMAL ARM DISARM CHIRPS page 9 of this manual Page 2 ARMING THE SYSTEM If the passive arming feature has been selected Turn the engine OFF exit the vehicle and close all doors hood and trunk The LED will begin to flash rapidly indicating that the 30 second passive arming timer has begun If
11. fies the triggered Page 4 zone For additional information refer to INTRUSION WARNING SIGNALS page 5 of this manual NOTE If the optional 2 step door unlock circuit is installed when the unlock transmitter button is activated the drivers door only will unlock pressing the unlock button a second time will cause all doors to unlock If your transmitter has a sperate lock unlock buttons pressing the unlock button anytime after the first unlock command will cause all the vehicle doors to unlock WHILE THE SYSTEM IS SOUNDING If during a triggered state you wish to shut off the siren horn without disarming your security system simply press and release any transmitter button other than the disarm button This action will turn off the siren yet leave the vehicle fully armed and protected This feature is particularly useful if you are aware of children playing near your vehicle that may accidently trigger your security system In this case you can cancel the siren horn sounding INTRUSION WARNING SIGNAL This system will inform you if an intrusion attempt has occurred while you were away from the vehicle Upon disarm the siren horn will chirp 4 times and the parking lights will flash 3 times Enter the vehicle and before turning on the ignition switch observe the LED flash pattern If the LED flashes 1 time pause 1 time pause etc then an intrusion attempt was made by impact or a strong vibration that the shock
12. h pattern The number of flashes identifies the triggered zone For additional information refer to INTRUSION WARNING SIGNALS page 5 of this manual If the siren horn did not sound upon disarm then the chirps have been turned off Refer to the section titled ELIMINATING THE NORMAL ARM DISARM CHIRPS page 8 NOTE If the optional 2 step door unlock circuit is installed when the unlock transmitter button is activated the driver s door only will unlock pressing the unlock button a second time will cause all doors to unlock SILENT DISARMING 1 As you approach the vehicle press and hold the disarm button of your transmitter for 2 seconds The parking lights will flash 2 times and the LED will turn off confirming that the system is disarmed The siren horn will not chirp If you have the optional door lock unlock circuit installed the doors will unlock If you have the optional entry illumination circuit installed the interior light will turn on for 30 seconds or until the ignition key is switched on NOTE If the passive arming mode was selected at time of installation the LED will start flashing rapidly indicating that the system is rearming Opening any door will suspend the automatic arming If the parking lights flashed 3 times and the siren horn chirps 4 times this indicates that the alarm system had been triggered in your absence Before turning on the ignition key examine the LED flash pattern The number of flashes identi
13. on from 1 up to 9 times Within 10 seconds of the last entered 10ths digit turn the ignition switch OFF then ON Within 10 seconds begin to enter your chosen units digit by pressing and releasing the button from 1 up to 9 times Finish by turning the ignition switch to the OFF position If the new code was accepted the system will report back the newly entered code by flashing the LED first indicating the 10ths digit pause and then the units digit The system will report the new code three times with a one second pause between each code then the system will begin arming If the LED flash pattern reports the previously stored code the new code was not entered correctly Please repeat steps 1 through 7 above considering the following NOTE Acceptable digits 10ths or units are 1 through 9 The system will not recognize a 0 Zero or no digit entered in any place units or tenths NOTE If 15 seconds of inactivity expire or if the ignition switch is turned off for more then 5 seconds during any of the above steps the system will revert back to the last successfully stored code CUSTOM CODE PROGRAMMING EXAMPLE To change the code from the factory pre assigned code of 11 to 52 you would do the following Disarm the system by using the transmitter or by using the emergency override sequence Turn the ignition switch to the ON position Within 10 seconds press and release the valet override button 3 times Within 10 seconds
14. on the programming set up by your installa tion center When you arrive at your vehicle unlock the vehicle by pressing and releasing the unlock button of your transmitter Enter the vehicle and turn the ignition key to the ON position The system WILL NOT start the vehicle if any one of the following conditions exist 1 The vehicle s hood Is opened 2 The gear shift selector is in any gear other than park 3 The brake is depressed SHUTTING DOWN THE REMOTE START To shut down the remote start feature form the transmitter press and release the transmitter button 2 times within 2 seconds REMOTE START VALET MODE Valet Mode is used to disable the system from remote starting To enter or exit valet mode simply follow the 4 steps outlined below 1 Push and hold the programming valet button 2 Cycle the ignition ON OFF ON OFF ON OFF 3 Release the programming valet button 4 The LED will flash 2 short flashes and 1 long flash when in remote start valet mode CAUTION Be certain that the vehicle is outdoors before using this or any remote vehicle starting device A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs DO NOT remote start the vehicle if the car is garaged ADDITIONAL REMOTE FUNCTION CHANNEL 3 TRUNK The system has an additional feature Channel 3 that can be connected to the Trunk Release To operate the accessory associated with
15. red or replaced under the terms of this warranty the defective Product must be returned to an authorized CODE dealer and accompanied by a copy of the retail sales receipt The date of purchase and year make and model of the vehicle in which the Product was originally installed must be clearly indicated on the sales receipt This warranty is exclusive and CODE MAKES NO OTHER WARRANTIES EXPRESSED OR IMPLIED ANY IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MER CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY IN NO CASE SHALL CODE BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WAR RANTY EXPRESS OR IMPLIED WHATSOEVER CODE does not warrant that the Product cannot be compromised or circumvented THE EXTENT OF CODE S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND IN NO EVENT SHALL CODE S LIABILITY EXCEED THE PURCHASE PRICE PAID BY THE ORIGINAL PURCHASER OF THE PRODUCT WITHOUT INSTALLATION LABOR Some states do not allow the exclusion or limitation of incidental or consequential dam ages so the above limitation may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state
16. turn the ignition switch OFF ON OFF ON OFF ON The siren horn will sound and the lights will flash 1 time Page 7 Within 10 seconds begin to press and release the push button switch to set the tenths digit As per example press and release 5 times to set the tenths digit to 5 Within 10 seconds of the last press of the button turn the ignition OFF then ON Within 10 seconds Begin to press and release the button to set the units digit As per example press and release 2 times to set the units digit to 2 Turn the ignition switch to the OFF position Immediately observe the LED flash pattern You will not the LED flashing 5 times pause and then flash 2 times pause This pattern will be repeated 3 times indicating the new code 52 has been accepted and stored in memory NOTE If after step 7 the LED flashes a code other than what was just entered this indicates that the code has not been changed You will have to repeat steps 1 through 7 above being certain to note the following Acceptable digits to this unit are 1 through 9 The unit will not recognize a 0 zero or no digit entered in any place units or tenths NOTE If 15 seconds of inactivity expire or if the ignition switch is turned OFF for more than 5 seconds during any of the above steps the unit will revert back to the last successfully stored code MANUALLY OVERRIDING YOUR SYSTEM USING THE CUSTOM CODE OVERRIDE Assuming the override
Download Pdf Manuals
Related Search