Airlink101 APO1200 Network Card User Manual
Contents
1. m Wireless Information 7 MAC Address 00 11 A3 0A 7B F2 Channel 44 Rate 300 Mb s Receive Bytes 1598647 Receive Packets 13938 Transmit Bytes 745872 Transmit Packets 1135 2 Make sure changed options as below ESSID Main_AP Channel 44 Security WPA2 PSK Cihper Type AES Pre shared Key VAP Informatio VAP ESSID MAC Address State Security Type Clients Primary AP Main_AP 00 11 A3 0A 7B F2 On WPA2PSK 0 VAP1 00 00 00 00 00 00 Off Disable 0 VAP2 00 00 00 00 00 00 Off Disable 0 VAP3 00 00 00 00 00 00 Off Disable 0 VAP4 00 00 00 00 00 00 Off Disable 0 VAPS 00 00 00 00 00 00 Off Disable 0 VAP6 00 00 00 00 00 00 Off Disable 0 Setting Up the Client Bridge Client Station 1 Follows steps 1 6 Select Client Bridge mode on step 4 in Section 3 Configuring the Access Point Make sure you change the IP address of the Client Station to be different 2 Configure the DHCP Server settings to match your demandand then click Next button 3 Click Site Survey button The system will automatically scan and display the scan results of all AP existing near by the system Wireless Station Setup This page is used to configure the parameters for connecting to the wireless network Band Mode 802 11 a n mixed mode Channel Frequency 44 5220MHz wt 4 Use Main_AP as an example here where the AP is encrypted via WPA2 PSK AES security type Click Selec2. 1 Follows steps in Section 5 Configuring for Client Bridge m Repeater AP Setup This page allows you active repeater AP for wireless LAN clients which may connect to your 2 Select Enable to active Repeater AP on Siakasa step 7 Enter the desired ESSID and click Repeater AP Enable pDisable Next button Repeater ESSID Main_AP_Repeater Note 1 To protect your network from any unauthorized access it is recommended to enable wireless encryption 2 The examples below are for WEP If you select WPA PSK or WPA2 PSK make sure your wireless adapters support WPA or WPA2 If your wireless adapters do not support WPA or WPA2 then select WEP m Repeater AP Security Setup Authentication Type open O sHarep O wepauto 5 Select WEP Key Index and Key then click WEH Key 2 This page allows you setup the repeater AP security Turn on WEP or WPA by using Encryption 3 Select the desired Secu rity Type Keys could prevent any unauthorized access to your wireless network Security Type WEP v r WEP 4 Select the Authentication Type for WEP Key Index 1 WEA Key 1 Finish Make sure to copy down the WEH Key 3 encryption key VER Key 4 Fa ag Please Wait 6 Wait 35 seconds while the Access Point reboots A System is restarting please wait for 35 seconds Connection Information 7 Cl ick Statu
3. 74 Wireless N A 5GHz 200mW Outdoor AP Model APOQ1200 Quick Installation Guide V 1 0 1 Before You Start Package Contents e APO1200 e Quick Installation Guide e CD ROM with User Manual and QIG e Power Adapter DC24V 0 5A e PoE injector e Mounting Kit System Requirement v Web Browser Internet Explorer 7 0 or above Firefox Safari v A Computer with a network adapter properly installed v 2x RJ 45 Ethernet cable Panel Function Description Front Panel Rear Panel 1 Reboot Button Unscrew the screw and click Reset button to restart system or reset to default configurations gt Press and hold the Reset button for 2 seconds and release to restart system The LED except Power indicator will be off before restarting gt Press and hold the Reset button for more than 10 seconds to reset the system to default configurations Power Green LED ON indicates power on and OFF indicates power off WLAN Green LED FLASH indicates Wireless Transmit LAN Green LED ON indicates connection OFF indicates no connection FLASH indicates packets transmit PoE Connector For connecting to PSE a W eS ww N N type Connector For connecting to N Type Antenna Application in Wireless Network APO1200 is a multiple mode system which can be configured either as a wireless gateway or an access point as desired It also can be used as a WDS link for Ethernet network expansion This section depicts diff
4. The NAT is enabled and PCs in LAN WLAN port share the same IP to ISP through WAN port The connection type can be setup in WAN page by using Static IP Dynamic IP PPPoE or PPTP Client AP In this mode the device can be used to Access Point for wireless clients connection the all ethernet ports and wireless interface are bridged together The NAT function is disabled all the WAN related function and firewall are not supported 4 Select AP mode and click Next button O WDS In this mode WDS Wireless Distribution Service creates a wireless backbone link between multiple access points that are part of the same wireless network This allows a wireless network to be expanded using multiple access points without the need for a wired backbone to link them as is traditionally required Client Bridge In this mode the device can connect to Access Point via a wireless link and used to repeater Access Point for wireless clients connection simultaneously the all ethernet ports and repeater Access Point are bridged together The NAT function is disabled all the WAN related function and firewall are not supported CPE AP In this mode the device can connect to Access Point via a wireless link and used to repeater Access Point for wireless clients connection simultaneously the all ethernet ports and repeater Access Point are bridged together The NAT is enabled PCs in ethernet ports and repeater Access Point share the s
5. Then click on Use the Use the following IP address follow IP address and make sure you assign your network adapter an IP address in the subnet of 192 168 2 X Subnet mask Obtain ONS serer address automatically IP address 1952 168 2 10d Use the following DNS server addresses Preferred ONS server Po Alternate ONS server Technical Support E mail support airlink101 com Toll Free 1 888 746 3238 Web Site www airlink101 com Theoretical maximum wireless signal rate derived from IEEE standard 802 11 specifications Actual data throughput will vary Network conditions and environmental factors including volume of network traffic building materials and construction mix of wireless products used radio frequency interference e g cordless telephones and microwaves as well as network overhead lower actual data throughput rate Specifications are subject to change without notice Photo of product may not reflect actual content All products and trademarks are the property of their respective owners Copyright 2010 Airlink101
6. ame IP to ISP through wireless WAN m LAN Interface Setup This page is used to configure the parameters for local area network which connects to the LAN port of your Access Point Here you may change the setting for IP Address Netmask etc 5 Configure the LAN settings to match your network settings and then click Next button P Address 192 168 2 254 IP Netmask 255 255 255 0 IP Gateway 192 168 2 1 DNS This page allows you assign DNS Server IP address 6 Configure the DNS settings to match your network settings and then click Next button DNS No Default DNS Server O Specify DNS Server IP Primary Secondary E Cia Cie Wireless Basic Setup This page is used to configure the parameters for connecting to the wireless network Band Mode 802 11 a n mixed mode v Channel Frequency 44 5220MHz v 7 Enter the desired Channel Frequency and ESSID Main_AP ESSID then click Next button Note 1 To protect your network from any unauthorized access it is recommended to enable wireless encryption 2 The examples below are for WPA2 PSK If you select WPA PSK or WPA2 PSK make sure your wireless adapters support WPA or WPA2 If your wireless adapters do not support WPA or WPA2 then select WEP m Wireless Security Setup p This page allows you setup the wir
7. eless security Turn on WEP or WPA by using Encryption Keys 8 Select the desired Secu rity Type could prevent any unauthorized access to your wireless network WPA PSK Security Type m WPA General 9 Select the Cipher Suite Type For WPA2 PSK ipher Suite AES M Pre shared Key 10 Enter a Pre shared Key and then click Finish button The key must be between 8 and 63 ASCII or 64 HEX characters Make sure to conv down the encrvntion kev Please Wait 11 oo seconds while the Access Point System Is restarting please wait for 35 seconds repoots Your Installation is complete For detailed information regarding the APO1200 s configuration and advanced settings please refer to User Manual 4 Configuring for WDS Link Note h The system provide WDS function on Router AP Mode AP Mode and WDS Mode WDS Link requires at least 2 APO1200 The Two wire networks LAN need the same subnet The WDS Link needs to be set at same Channel and with same Security Type Please install and test in a lab environment before mounting the APO1200 After you set the APO1200 to WDS Mode wireless clients will not be able to connect to the APO1200 oo 7 w N The examples below are for WDS Mode 192 168 2 254 MAC 00 11 A3 OA B F2 192 168 2 253 MAC 00 11 A3 04 7B FA WDS l 192 168 2 X 192 168 2 X Setting Up the Main APO1200 Main Base Station Wirel
8. erent applications on Router AP Mode AP Mode WDS Mode CPE Mode Client Bridge Universal Repeater Mode and CPE AP Mode Router AP WDS Mode p u AP WDS Mode Remte 192 168 2 20 100 _ Remote Base Station Base Station APO1200 192 168 2 10 WAN WLAN APO1200 192 168 2 10 197 168 1 254 192 168 2 254 192 168 2254 WDS Mode CPE Mode 192 168 2 x Base Station WBS 192 168 2 250 ae e 192 168 2 x Remote Main Sa APO1200 WDS Mater A Base Station APO1200 192 168 2 254 192 168 1 250 WiFi WAN LAN a 192 168 1 254 192 168 2 254 192 168 2 x 192 168 2 X Remote Base Station 192 168 2 252 Client Bridge Universal Repeater Mode CPE AP Mode Main Base Station APO1200 192 168 2 10 oe ce APO1200 192 168 2 10 192 168 2 250 182 16 2 254 192 168 1 250 WiFi WAN LAN a oe 192 168 1 254 192 168 2 254 a9 192 168 2 X 192 168 2 X 2 Hardware Installation DATA OUT Connect N type antenna to the N type connector on the rear panel Connect one end of a RJ 45 cable into the AP s PoE connector Connect the opposite end of the RJ 45 cable to the P DATA OUT port on the Power over Ethernet Injector Connect one end of another RJ 45 cable to the DATA IN port on the Power over Ethernet Injector Connect the opposite end of the RJ 45 cable to a LAN port on your network or Computer Connect the power cord into the Power over Etherne
9. ess Information MAC Address 00 11 A3 0A 7B FA 1 Copy down the 12 digit MAC Address of the Channel 44 Remote APO1200 Remote Base Station 1 kene Mb s The MAC Address is on the Benatti Overview Page Status gt Overview and Transmit Bytes 33683 Wireless General Setup Page Wireless Transmit Packets 346 gt General Setup m General Setup MAC Address 00 11 A43 0A 7B FA Band Mode 802 11 a n mixed mode AP Isolation Enable Disable Country NONE w Channel 44 v Tx Power 10 2 Follows steps 1 6 Select WDS mode on step 4 in Section 3 Configuring the Access Point Enter the desired Channel Frequency then click Next button Click Enable and enter the Remote APO1200 s MAC Address Select the desired Security Type between WDS link then click Finish button Wait 35 seconds while the Access Point reboots m Wireless Basic Setup This page is used to configure the parameters for connecting to the wireless network Band Mode 802 11 a n mixed mode v Channel Frequency 44 5220MHz WDS MAC Setup This page allows you setup the WDS link Enter the remote WDS peers MAC address and select an apporapriate security type for WDS link O Disable Peer s MAC Address 00 11 a3 oa 7B FA WDS Mode Enable m Wireless Security Setting Security T
10. it for 35 seconds 8 Click Status gt Remote AP the Connection Information should be display Connection Information ESSID MAC Address Signal Strength ANTO Signal Strength ANT1 BandWidth Main AP 00 11 A3 0A 7B F2 100 50dBm 100 47dBm 40MHz Note 1 To verify wired network of Client Station can access Main Base Station use ping command to 192 168 2 254 2 If you can not access Main Base Station verify the IP address of the wired client PC or Laptop is in the same subnet with Main Base Station 6 Configuring for Universal Wireless Repeater Note 1 This section will walk you through the steps of sharing bridging an internet connection in one building and extending that same internet to another building with repeat Access Point 2 Arepeater is just a very normal client which at the same time can also be an access point independent of the SSID and type of encryption used 3 The Main Base Station provides Access Point with SSID Main_AP and the Client Station provide repeat Access Point with SSID Repeater _Main_AP 4 The Wireless clients and Main Base Station need the same subnet 5 The examples below are for Universal Wireless Repeater 192 168 2 254 MAC 00 11 A3 0A 7B F2 192 168 2 253 MAC 00 11 A3 04 7B FA 192 168 2 10 i E n of d l Ht aan i ve 1 1 I ir i H LAN REE 192 168 2 192 168 2 X
11. s gt Remote AP the Connection ESSID MAC Address Signal Strength ANTO Signal Strength ANT1 BandWidth Main_AP 00 11 A3 0A 7B F2 100 50dBm 100 47dBm 40MHzZ Information should be display 8 Set Wireless client associate to ESSID Repeater_Main_AP with corrent WEP key m Repeater AP Clients l MAC Address OA ign BandWidth We CAE Disconnect 9 Click Status gt Client the Repeater AP Clients should be display 00 90 CC 0F 51 38 100 41dBm 100 41dBm 20MHz 0 58 Note 1 The Channel of Repeat AP should be the same with Main Base Station To verify wireless clients can associate ESSID Repeater_Main_AP with WEP key To verify wireless clients can use ping command to 192 168 2 254 gt N If you can not access Main Base Station verify the IP address of the wireless client PC or Laptop is in the same subnet with Main Base Station 7 How to configure TCP IP settings on your PC Windows XP 2000 1 Go into the Control Panel double click the Network Connections icon and then right click the Local Area Connection icon and then click Pronerties Internet Protocol TCP IP Properties General You can get IF settings assigned automatically if your network supports this capability Otherwise You need to ask your network administrator for the appropriate IP settings 2 Click Internet Protocol TCP IP and then Obtain an IP address automatically click Properties
12. s Point for wireless clients connection simultaneously the all ethernet ports and repeater Access Point are bridged together The NAT is enabled PCs in ethernet ports and repeater Access Point share the same IP to ISP through wireless WAN comet Caack Caer DHCP Server This page is used to configure the parameters for DHCP Server which LAN WLAN clients can get IP address automatically Here you may change the setting for release IP Address range DHCP O Enable Disable Start IP 192 168 2 Scan Result ESSID MAC Address Signal Channel Security Band Network Type Select Main_AP 00 11 a3 0a 7b f 100 44 WPAZPSKIAES 11a Infrastructure Select m Station Security Setup This page allows you setup the wireless security Select an apporapriate security type for association 5 Set Client Bridge associate to ESSID i Security Type WPaz PsK EE Main_AP with corrent Pre shared key Then click Next button WPA Cipher Suite Pre shared Key m Repeater AP Setup This page allows you active repeater AP for wireless LAN clients which may connect to your repeater Access Point 6 Select Disable to deactivate Repeater AP Then click Finish button Repeater AP Enable pisable Repeater ESSID _AP_Repeate 7 Wait 35 seconds while the Access Point reboots A system Is restarting please wa
13. t Injector Then connect the power cord to a power outlet 3 Configuring the Access Point Note 1 Itis recommended that you configure the Access Point from a wired computer Before the Access Point can be configured if you connect the AP to your computer directly you must manually assign a static IP address to your computer s network adapter in the subnet of 192 168 2 x Refer to Section 7 How to configure TCP IP settings on your PC if you connect the AP to your Router or Switch since the AP s default IP address is 192 168 2 254 make sure your Router s IP address is 192 168 2 x and no other network devices are assigned an IP address of 192 168 2 254 2 Disable any anti virus and firewall programs before configuring the access point 1 Open the web browser Internet Explorer or Mozilla Firefox Enter the AP s default IP address http 192 168 2 254 and click GO The server 192 168 2254 at APO1200 requires a username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection 2 Enter root for user name and default for password 3 Click Wizard m Operating Mode You may configure the different operating mode suitable for your environment O Router AP In this mode the device is supposed to connect to internet via ADSL Cable Modem
14. t button of the Main_AP and then click Next button Operating Mode You may configure the different operating mode suitable for your environment O Router AP In this mode the device is supposed to connect to internet via ADSL Cable Modem The NAT is enabled and PCs in LAN WLAN port share the same IP to ISP through WAN port The connection type can be setup in WAN page by using Static IP Dynamic IP PPPoE or PPTP Client O AP In this mode the device can be used to Access Point for wireless clients connection the all ethernet ports and wireless interface are bridged together The NAT function is disabled all the WAN related function and firewall are not supported wos In this mode WDS Wireless Distribution Service creates a wireless backbone link between multiple access points that are part of the same wireless network This allows a wireless network to be expanded using multiple access points without the need for a wired backbone to link them as is traditionally required Client Bridge In this mode the device can connect to Access Point via a wireless link and used to repeater Access Point for wireless clients connection simultaneously the all ethernet ports and repeater Access Point are bridged together The NAT function is disabled all the WAN related function and firewall ar not supported O CPE AP In this mode the device can connect to Access Point via a wireless link and used to repeater Acces
15. ype Disable w Please Wait A system Is restarting please wait for 35 seconds Setting Up the Remote APO1200 Remote Base Station Copy down the 12 digit MAC Address of the Main APO1200 Main Base Station The MAC Address is on the device label or the Overview Page Status gt Overview and Wireless General Setup Page Wireless gt General Setup Repeat steps 2 6 in Setting Up the Main APO1200 for the Remote APO1200 Make sure you change the IP Address of the Remote APO1200 to be different from the Main APO1200 Click Status gt WDS Status Verify the Remote APO1200 s MAC Address and Signal Strength RSSI MAC Address 00 11 A3 0A 7B FA 100 41 dBm 76 60 dBm HTMIX 40M 15 WDS Link Status Signal Strength ANTO Signal Strength ANT1 Phy Mode BandWidth MCS SGI 1 5 Configuring for Client Bride Note 1 This section will walk you through the steps of sharing bridging an internet connection in one building and extending that same internet to another building 2 The Main Base Station provide Access Point with SSID Main_AP 3 The Two wire networks LAN need the same subnet 4 The examples below are for Client Bridge 192 168 2 254 MAC 00 11 A3 0A 7B F2 192 168 2 253 MAC 00 11 A3 0A 7B FA 192 168 2 X 192 168 2 X Setting Up the Access Point Main Base Station 1 Follows steps in Section 3 Configuring the Access Point
Download Pdf Manuals
Related Search