Air King 9848 Fan User Manual
Contents
1. 3 Replace the front cover of the switch control box with the supplied screws and tighten 4 Make sure the electrical box is properly secured Connect the White wire from the fan to the White wire from the supply Connect the Black wire from the fan to the Black hot wire from the wall switch Connect the Green or Bare Copper ground wire from the house to the Green wire from the fan Use approved methods for all connections and carefully push wires up into the outlet box Figure 5 Hot Black Ground Figure 5 from fan CAUTION CHECK TO CONFIRM THAT ALL CONNECTIONS ARE TIGHT INCLUDING THE GROUND AND THAT NO BARE WIRE IS VISIBLE AT THE CONNECTIONS EXCEPT IN THE CASE THAT A BARE WIRE WAS USED FOR THE GROUND WIRE 5 Slide upper canopy up the downrod until itis snug against the ceiling Tighten both set screws Figure 6 CAUTION MAKE SURE THAT THE ELECTRICAL WIRES ARE COMPLETELY INSIDE THE ELECTRICAL BOX AND NOT PINCHED BETWEEN THE CEILING CANOPY AND THE CEILING SECTION 5 Installing the Blades CAUTION THE BLADES SHOULD BE ATTACHED TO THE FAN MOTOR AFTER IT IS HUNG AND WIRED IF THE BLADES ARE ATTACHED WHILE THE MOTOR IS ON THE FLOOR THE BLADES COULD GET BENT CAUSING THE FAN TO WOBBLE NOTE Wires omitted Figu re 6 from figure for clarity 1 Insert one screw through the spring washer paper washer and into the motor hub Do not tighten fully at this time Figure 7 Screw Spring Washer Paper Was2. CTRIC SHOCK OR PERSONAL INJURY PROPERLY INSTALL TO AN OUTLET BOX MARKED ACCEPTABLE FOR FAN SUPPORT USE SCREWS PROVIDED WITH OUTLET BOX MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF LIGHTING FIXTURES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND MAY NEED TO BE REPLACED CONSULT A QUALIFIED ELECTRICIAN IF IN DOUBT 2 Electrical Box This unit will fit any of the following electrical boxes 4 octagon box 3 octagon box 1 2 deep ceiling pan or a plaster ring with 3 1 2 mounting hole centers mounted on one of the above listed boxes This fan will also install on a Wiremold No 5738 fixture box The electrical box must be securely anchored and capable of withstanding a load of at least 35 pounds CAUTION IF ONE OF THE ABOVE ELECTRICAL BOXES IS NOT PRESENT FOR PROPER INSTALLATION CONTACT A LICENSED ELECTRICIAN SECTION 2 Preparing the Ceiling Fan 1 Unpack fan from the carton and confirm that all pieces are present The following should be present 1 Motor assembly 1 Lower canopy 1 Upper canopy 6 Blade lock washers 6 Blade screws 1 Downrod assembly 1 J hook bracket 1 Wall control 3 Blades 2 Install J Hook Bracket to an electrical box marked Acceptable For Fan Support using the screws provided with the outlet box Insert the screws through the slotted holes in the bracket and attach to the electrical box Tighten both screws Figure 1 CAUTION IF BRACKET AND OR ELECTRICAL BOX ARE NOT
3. ED IN POTENTIALLY DANGEROUS LOCATIONS SUCH AS FLAMMABLE EXPLOSIVE CHEMICAL LADEN OR WET ATMOSPHERES 5 Make certain that the power source conforms to the electrical requirements of the fan 6 The fan must be hung with at least 10 feet of clearance from the floor to the blades 7 Completely reassemble fan according to instructions before reconnecting to power supply WARNING T0 REDUCE THE RISK OF PERSONAL INJURY DO NOT BEND THE BLADE BRACKETS OR BLADES WHEN INSTALLING THE BLADES BALANCING THE BLADES OR CLEANING THE FAN DO NOT INSERT FOREIGN OBLECTS IN BETWEEN THE ROTATING FAN BLADES 8 This fan is not for use in wet or damp locations 9 Do not use fan outdoors and never locate the fan where it may fall into a bathtub or other water container 10 This unit must be grounded 11 To avoid motor bearing damage and noisy and or unbalanced impellers keep drywall spray construction dust etc off power unit WARNING To REDUCE THE RISK OF FIRE ELECTRIC SHOCK DO NOT USE THIS FAN WITH ANY SOLID STATE SPEED CONTROL DEVICE SAVE THESE INSTRUCTIONS 984856 Rev B 7 07 WWW AIRKINGLIMITED COM 1of4 INSTALLATION INSTRUCTIONS CAUTION MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE STARTING INSTALLATION SECTION 1 Installation Requirements 1 Electrical Requirements This unit requires a grounded electrical supply line of 120 volts AC 60 Hz 15 amp circuit WARNING To REDUCE THE RISK OF FIRE ELE
4. IMPORTANT INSTRUCTIONS OPERATING MANUAL Models 9848 9856 9856UF e e Ventilation Products iG Ceiling Fan BUILDERS CHOICE READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE INSTALL OPERATE OR MAINTAIN THE PRODUCT DESCRIBED PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND OR PROPERTY DAMAGE RETAIN INSTRUCTIONS FOR FUTURE REFERENCE GENERAL SAFETY INFORMATION When using electrical appliances basic precautions should always be followed to reduce the risk of fire electric shock and injury to person including the following WARNING To REDUCE THE RISK OF FIRE ELECTRIC SHOCK AND INJURY TO PERSON OBSERVE THE FOLLOWING 1 Read all instructions before installing or using fan 2 Use this unit only in the manner intended by the manufacturer If you have questions contact the manufacturer 3 Before servicing or cleaning the unit switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a prominent warning device such as a tag to the service panel 4 Installation work and electrical wiring must be done by qualified person s in accordance with all applicable codes and standards including fire related construction CAUTION THis FAN MUST NOT BE US
5. SECURELY ATTACHED THE FAN COULD WOBBLE 1 Package containing 4 Flat washers 2 8 32 screws 2 8 lock washers 2 10 lock washers 3 Wire nuts 2 Wood screws 1 Instruction Safety Sheet Electrical Box 984856 Rev B 7 07 WWW AIRKINGLIMITED COM SECTION 3 Mounting the Fan 2 Carefully lift the fan and hang on the J Hook ensuring that all wires are clear of the rubber roller Figure 2 p Hook Bracket N O Upper Canopy Rubber Roller Downrod NOTE Wires omitted from figure for clarity WARNING FAILURE TO SEAT DOWNROD ASSEMBLY ON J HOOK BRACKET COULD CAUSE DAMAGE TO ELECTRICAL WIRES AND CAUSE FAN TO FALL CAUTION DONOTPINCH WIRES BETWEEN THE J HOOK AND DOWNROD ASSEMBLY 2 Slide lower canopy down the downrod until it is snug against the motor housing Tighten both set screws Figure 3 SECTION 4 Wiring NOTE Wires omitted from figure for clarity CAUTION ALLELECTRICAL CONNECTIONS MUST BE MADE IN ACCORDANCE WITH LOCAL CODES ORDINANCES OR NATIONAL ELECTRICAL CODE IF YOU ARE UNFAMILIAR WITH METHODS OF INSTALLING ELECTRICAL WIRING SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN 1 Unscrew the speed control cover and screw base to wall 2 Connect the Black Hot supply wire into socket marked A Connect the Black lead wire from the fan into socket marked F and tighten screws Figure 4 Wall Control 2of4
6. Washer Upper Downrod Bracket Mounting Bracket Bolt Downrod Blade Screws Blade Lock Washer Paper Washer Blade Lower Canopy Lower Downrod Bracket Capacitor Capicitor Mounting Screw Motor Ground Wire Ground Wire Screw Wall Control slal ISa l BR al SIS x e a wn el se Installer Installation Date Place of Purchase Model Number 984856 Rev B 7 07 WWW AIRKINGLIMITED COM 4of4
7. bulb heater combinations As well any damage or failure caused by abuse misuse abnormal usage faulty installation or improper maintenance will not be covered by this warranty In order to make a claim on this warranty you must be the original consumer of the product You will be required to present to Air King the original bill of sale showing date of purchase place of purchase and model purchased Failure to meet these requirements will void your warranty Air King will not be held responsible for any bodily injury or damages to personal property or real estate whether caused directly or indirectly by the product Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages and some states do not allow limitations on how long an implied warranty lasts so these exclusions or limitations may not apply to you This warranty gives you specific legal rights and you may have other rights which vary from state to state and province to province FOR PARTS OR TECHNICAL ASSISTANCE Please call 1 800 465 7300 MONDAY THROUGH FRIDAY BETWEEN THE HOURS OF 8 AM AND 4 00 PM EST PLEASE DO NOT RETURN PRODUCT TO PLACE OF PURCHASE Reference the type and style of product located on label inside of the product when you call For more information please visit our website wwwairkinglimited com Description J Hook Bracket Upper Canopy Canopy Set Screw Cross Pin Cotter Pin Rubber Roller Hex Nut Lock
8. gested Remedy 1 Check main and branch fuse or circuit breaker 2 Check line wire connections to the fan 3 Turn wall control to desired setting 1 2 Fan sounds noisy 1 Screws securing fan blades to motor housing are loose Check to be sure screws are tight 2 Wire nuts inside electrical box are rattling 2 Check wire nut connections in electrical box 3 Fan wobbles or shakes excessively 1 2 Fan blades not seated properly 3 Fan blades out of balance 984856 Rev B 7 07 Screws securing fan blade brackets to motor housing are loose WWW AIRKINGLIMITED COM 1 Check to be sure screws are tight 2 Check that blades are seated firmly to top of motor housing 3 Interchanging adjacent side by side blade pairs can redistribute the weight and result in smoother operation 3 0f 4 LIMITED WARRANTY All products manufactured by Air King Limited are warranted for one year from the date of purchase against defects in workmanship and or material In addition all ventilating exhaust fans heaters combination fan lights and or heaters and range hoods are guaranteed for five years from the date of purchase against defects in workmanship and or material This warranty does not cover any labor or shipping costs or the cost of replacement components as part of routine maintenance such as range hood grease filters charcoal filters or combination charcoal grease filters replacement light bulbs in range hoods or bathroom fan light
9. her 2 Install second screw in the same manner then tighten both screws fully 3 Repeat steps 1 and 2 for the 2 remaining blades SECTION 10 Operation 1 Restore electrical power to the wall switch by turning the electricity on at the main fuse box 2 Check the operation of the fan by selecting a speed on wall switch NOTE Model 9856UF is a single speed that directs the airflow upwards SECTION 11 Maintenance and Cleaning CAUTION MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE SERVICING THE UNIT WARNING DO NOT DEPEND UPON THE FAN S CONTROLS AS THE SOLE MEANS OF DISCONNECTING POWER WHEN INSTALLING OR SERVICING THE FAN ALWAYS TURN POWER OFF AT THE MAIN FUSE BOX WARNING DO NOT USE WATER WHEN CLEANING IT COULD DAMAGE THE MOTOR OR BLADES AND CREATE THE POSSIBILITY OF AN ELECTRICAL SHOCK OR FIRE CAUTION DO NOT USE GASOLINE BENZINE THINNER HARSH CLEANSERS ETC AS THEY MAY DAMAGE THE FAN 1 Use only a soft brush or lint free cloth to avoid scratching the finish Abrasive cleaning agents are not required and should be avoided to prevent damage to the finish NEVER USE ANY ABRASIVE PADS OR SCOURING POWDERS NEVER IMMERSE ELECTRICAL PARTS IN WATER 2 The fan is permanently lubricated and does not require oiling Troubleshooting Guide Trouble Probable Cause 1 Fan will not start 1 Fuse or circuit breaker blown or OFF 2 Loose power connections 3 Wall Control in the off position Sug
Download Pdf Manuals
Related Search