AEG 45003 Dishwasher User Manual
Contents
1. e Serial number S N For these data refer to the rating plate Write the necessary data here Model description Technical data Product number Serial number The cleaning results are not satisfactory The dishes are not clean Limescales particles on the dishes The selected washing programme is not applicable for the type of load and soil The baskets are loaded incorrectly so that water cannot reach all surfaces Spray arms do not turn freely because of incorrect arrangement of the load The filters are dirty or not correctly installed The quantity of detergent is too little or missing The salt container is empty e The water softener is adjusted on a wrong level e The salt container cap is not closed correctly The dishes are wet and dull e There are streaks milky spots ora bluish coating on glasses and dishes Dry water drop signs on e glasses and dishes TECHNICAL DATA Dimensions Electrical connection Voltage Overall power Fuse Water supply pressure Capacity No rinse aid has been used The rinse aid dispenser is empty Decrease the rinse aid dosage Increase rinse aid dosage The detergent can be the cause Width cm 59 6 Height cm 85 Depth cm 62 5 Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher door Minimum 0 5 bar 0 05 MPa Maximum 8 bar 0 8 MPa Pla2. set the water softener level To deactivate activate the rinse aid dispenser The appliance is not in setting mode when e One or more phase indicator lights are on e The time duration of the programme does not flash In this condition cancel the programme to go back to the setting mode Refer to the chapter Setting and starting a washing programme USE OF THE APPLIANCE Refer to the following instructions for each step of procedure 1 Make a check if the water softener level is correct for the water hardness in your area f necessary set the water softener Fill the salt container with dishwasher salt Fill the rinse aid dispenser with rinse aid Load cutlery and dishes into the dishwasher Set the correct washing programme for the type of load and soil Fill the detergent dispenser with the correct quantity of detergent Start the washing programme i If you use combi detergent tablets 3 in 1 4in 1 5 in 1 etc refer to the chapter Multitab function ALO O1 GB Cor SETTING THE WATER SOFTENER The water softener removes minerals and salts from the water supply Minerals and salts can have bad effect on the operation of the appliance ENA Setting the water softener Water hardness is measured in equivalent scales e German degrees dH e French degrees TH e mmol l millimol per litre international unit for the hardness of water e Clarke Adjust the water softener to
3. supplier Remove all packaging before first use A qualified and competent person must do the electrical installation A qualified and competent person must do the plumbing installation Do not change the specifications or modify this product Risk of injury and damage to the appliance Do not use the appliance if the mains cable or water hoses are damaged if the control panel worktop or plinth area are damaged that you can get access to the inner side of the appliance Contact your local Service Force Centre Do not drill into the sides of the appliance to prevent damage to hydraulic and electrical components WARNING Carefully obey the instructions for electrical and water connections PRODUCT DESCRIPTION Control panel Upper basket Water hardness dial Salt container Detergent dispenser Rinse aid dispenser Kall Rating plate Filters EJ Lower spray arm EJ Upper spray arm Worktop CONTROL PANEL AUTO 45 70 30 MIN 60 INTENSIV CARE 70 ECO 50 Programme knob ultitab button MULTITAB Delay start button DELAY Start button START Digital display ndicator lights Programme marker Off position Function buttons DEONTESSNES BSW Control panel Indicator lights Wash phase Comes on when the washing phase or the rinsing phase operates Dry phase Comes on when the drying phase operates Multitab C
4. FAVORIT 45003 User manual Dishwasher Contents Thank you for choosing one of our high quality products To ensure optimal and regular performance of your appliance please read this instruction manual carefully It will enable you to navigate all processes perfectly and most efficiently To refer to this manual any time you need to we recommend you to keep it ina safe place And please pass it to any future owner of the appliance We wish you much joy with your new appliance OPERATING INSTRUCTIONS 3 MULTITAB FUNCTION 16 SAFETY INFORMATION 3 WASHING PROGRAMMES 17 Correct use 3 SELECT AND START A WASHING PROGRAMME General safety 3 18 Child safety 3 Interrupting a washing programme 19 nstallation di Cancelling a washing programme 19 PRODUCT DESCRIPTION 4 Setting and starting a washing programme CONTROL PANEL 5 with delay start 19 Programme knob 6 Cancelling a delay start 19 ultitab button 6 End of the washing programme 19 Delay start button 6 Standby mode 20 Start button 6 Removing the load 20 Digital display 6 CARE AND CLEANING 20 Function buttons 7 Cleaning the filters 20 Setting mode 7 External cleaning 21 USE OF THE APPLIANCE 7 Frost precautions 21 SETTING THE WATER SOFTENER 75 SLT DOE ai Manual adjustment 8 TECHNICAL DATA 23 Electronic adjustment 8 INSTALLATION INSTRUCTIONS 23 USE OF DISHWASHER SALT 9 INSTALLATION 23 USE OF RINSE AID 9 Fitting under a counter 23 Adjusting t
5. SE OF DISHWASHER SALT CAUTION A i Only use dishwashers salt Types of salt that are not applicable for dishwashers cause dam age to the water softener CAUTION Grains of salt and salty water on the bottom of the appliance can cause corrosion Fill the appliance with salt before you start a washing programme to prevent corrosion Do these steps to fill the salt container 1 2 3 4 5 It is normal that water overflows from the salt container when you fill it with salt When you set electronically the water soft ener to level 1 the salt indicator light does not stay on Turn the cap anticlockwise to open the salt container Fill the salt container with 1 litre of water only the first operation Use the funnel to fill the salt container with salt Remove the salt around the opening of the salt container Turn the cap clockwise to close the salt container USE OF RINSE AID A i CAUTION Only use branded rinse aid for dishwashers Do not fill the rinse aid dispenser with other products e g dishwasher cleaning agent liquid detergent This can cause damage to the appliance Rinse aid makes it possible to dry the dishes without streaks and stains Rinse aid is automatically added during the last rinsing phase Do these steps to fill the rinse aid dispenser BET Use of rinse aid 1 Press the release button A to open the rinse aid dispenser 2 Fill the r
6. ce settings 12 INSTALLATION INSTRUCTIONS INSTALLATION Fitting under a counter WARNING Make sure that the mains plug is disconnected from the mains socket during installation Installation Put the appliance adjacent to a water tap and a water drain Remove the appliance worktop to install it under a sink unit or a kitchen worktop Make sure that the dimensions of the recess agree with the given dimensions Do these steps to remove the appliance worktop 1 Remove the rear screws 1 2 Pull the worktop from the behind the ap pliance 3 Lift the worktop and move it from the front slots 4 Use the adjustable feet to adjust the level of the appliance Install the appliance under the kitchen work top Make sure that there are no kinks in the water hoses and that the water hoses are not squashed If a repair is necessary the appliance must be easily accessible for the engineer Install the appliance worktop to the appliance if you want to use the dishwasher as a freestanding appliance The plinth on freestanding appliance is not adjustable Adjusting the level of the appliance Make sure that the appliance is level to close and seal the door correctly If the level of the appliance is correct the door does not catch on the sides of the cabinet If the door does not close correctly loosen or tighten the adjustable feet until the appliance is level Water conne
7. ction WATER CONNECTION Water inlet hose Connected the appliance to a hot max 60 or cold water supply If the hot water comes from alternative sources of energy that are more environmentally friendly e g solar or photovoltaic panels and aeolian use a hot water supply to decrease energy consumption Connect the inlet hose to a water tap with an external thread of 3 4 CAUTION Do not use connection hoses from an old appliance The water pressure must be in the limits refer to Technical data Make sure that the local water authority gives you the average mains pressure in your area Make sure that there are no kinks in the water inlet hose and that the water inlet hose is not squashed or entangled Fit the locknut correctly to prevent water leaks CAUTION Do not connect the appliance to new pipes or pipes that are not used for a long time Let the water run for some minutes then connect the inlet hose The water inlet hose is double walled and has an inner mains cable and a safety valve The water inlet hose is under pressure only while the water is running If there is a leak in the water inlet hose the safety valve interrupts the running water Be careful when you connect the water inlet hose e Do not put the water inlet hose or the safety valve in water e f the water inlet hose or the safety valve is damaged immediately disconnect the mains plug from the mains socket e Only let the Service F
8. display shows the necessary delay start time for the washing programme Delay start time flashes in the digital display 3 Press the start button The countdown of the delay start starts The phase indicator lights of the washing programme go off In the digital display the delay start time is on with a static light When the countdown is completed the washing programme automatically starts The phase indicator light of the phase in progress comes on i Do not open the door during the countdown to prevent interruption of the countdown When you close the door again the countdown continues from the point of interruption Cancelling a delay start 1 Press and hold function buttons A and B The phase indicator lights or light come on In the digital display the time duration of the washing programme comes on 2 Press the start button to start the washing programme End of the washing programme Switch off the appliance in these conditions e The appliance stops automatically e The digital display shows a zero e The phase indicator lights are off For better drying results keep the door ajar for some minutes before you remove the dishes Let the dishes cool down before you remove them from the appliance Hot dishes are easily damaged Care and cleaning Standby mode If you do not switch off the appliance at the end of the washing programme the appliance automatically goes into standby mode The standby mode decrea
9. down e Put knives with the handles up e Mix spoons with other cutlery to prevent them to bond together Loading cutlery and dishes You can open the cutlery basket to remove the cutlery more easily Do these steps to remove the cutlery 1 Put the cutlery basket on a table or work sur face 2 Open the handle 3 Remove the cutlery i Hold the two parts of the handle tightly when you move the cutlery basket Upper basket The upper basket is for saucers salad bowls cups glasses pots and lids Arrange the items to let wa ter touch all surfaces M e For longer items fold the cup racks up e Put glasses with long stems in the cup racks with the stems up E hy Loading cutlery and dishes e For glasses with long stems turn the glass holder to the left or to the right e You can fold up or down the row of prongs on the left side of the upper basket to in crease load flexibility Z dr Adjustment of the height of the upper basket You can put the upper basket in two positions to increase load flexibility Maximum height of the dishes in Po the upper basket the lower basket Upper position 22 em 30 cm Lower position 24 cm 29 cm Do these steps to move to the upper basket to the lower upper position 1 Pull out the upper basket
10. ese tablets contain agents such as detergent rinse aid and dishwasher salt Some types of tablets can contain other agents Do a check if these tablets are applicable for the local water hardness Refer to the in structions from the manufacturer When you set the multitab function it stays on until you deactivate it The multitab function stops automatically the flow of rinse aid and salt The rinse aid indicator light and salt indicator light are deactivated The programme duration can increase if you use the multitab function i Activate or deactivate the multitab function before the start of a washing programme You cannot activate or deactivate the multitab function when the programme operates Cancel the washing programme then set the programme again To activate the multitab function e Press the multitab button The multitab indicator light comes on To deactivate the multitab function e Press the multitab button The multitab indicator light goes off i Do these steps if the drying results are not satisfactory 1 Fill the rinse aid dispenser with rinse aid 2 Activate the rinse aid dispenser 3 Set the rinse aid dosage to position 2 e You can only activate or deactivate the rinse aid dispenser when the multitab function is activated To activate deactivate the rinse aid dispenser Washing programmes i The appliance must be switched off 1 N Press and hold function button A Turn the programme knob co
11. he rinse aid dosage 10 Do these steps to remove the appliance LOADING CUTLERY AND DISHES 11 worktop 24 Helpful hints and tips 11 Adjusting the level of the appliance 24 Lower basket 11 WATER CONNECTION 25 Cutlery basket 12 Water inlet hose 25 Upper basket 13 Water drain hose 25 Adjustment of the height of the upper ELECTRICAL CONNECTION 26 basket 14 USE OF DETERGENT is ENVIRONMENT CONCERNS 26 Subject to change without notice Safety information OPERATING INSTRUCTIONS SAFETY INFORMATION i For your safety and correct operation of the appliance read this manual carefully before installation and use Always keep these instructions with the appliance even if you move or sell it Users must fully know the operation and safety features of the appliance Correct use The appliance is designed exclusively for domestic use Only use the appliance to clean household utensils that are applicable for dishwashers Do not put solvents in the appliance Risk of explosion Put the knives and all items with sharp points in the cutlery basket with their points down If not put in a horizontal position in the upper basket Use only branded products for dishwashers detergent salt rinse aid f you open the door while the appliance is in operation hot steam can escape Risk of skin burns e Do not remove dishes from the dishwasher before the end of the washing programme When the washing programme is completed disconnect the mains
12. hing programme 1 Close the door 2 Turn the programme knob to set the washing programme Refer to the chapter Washing programmes The phase indicator light or lights for the washing programme come on The programme duration in the digital display flashes 3 Press the start button The washing programme starts automatically When the programme starts only the indicator light of the phase in progress stays on Programme duration is on with a static light When the washing programme operates you cannot change the programme Cancel the washing programme WARNING Only interrupt or cancel a washing programme if necessary gt te Select and start a washing programme HEM CAUTION Open the door carefully Hot steam can come free Interrupting a washing programme Open the door e The programme stops Close the door e The programme continues from the point of interruption Cancelling a washing programme e Press and hold function buttons A and B Inthe digital display the time duration of the programme flashes One or more phase indicator lights are on The washing programme is cancelled At this time you can do these steps 1 Switch off the appliance 2 Seta new washing programme Fill the detergent dispenser with detergent before you set a new washing programme Setting and starting a washing programme with delay start 1 Seta washing programme 2 Press the delay start button until the
13. inse aid dispenser with rinse aid The mark max shows the maximum level 3 Remove the spilled rinse aid with an ab sorbent cloth to prevent too much foam during the subsequent washing pro gramme 4 Close the rinse aid dispenser Adjusting the rinse aid dosage The rinse aid is set at the factory at position 4 lt You can set the rinse aid dosage between position 1 lowest dosage and position 6 highest dosage Turn the rinse aid dial to increase or decrease the dosage Increase the dosage if there are water droplets or limescale on the dishes Decrease the dosage if there are streaks whitish stains or bluish layers on the dishes Loading cutlery and dishes KTM LOADING CUTLERY AND DISHES Helpful hints and tips CAUTION Only use the appliance for household utensils that are applicable for dishwashers Do not use the appliance to clean objects that can absorb water sponges household cloths etc e Before you load cutlery and dishes do these steps Remove all food remainings and debris Make burnt remaining food in pans soft While you load cutlery and dishes do these steps Load hollow items e g cups glasses and pans with the opening down Make sure that water does not collect in the container or in a deep base Make sure that cutlery and dishes do not lie inside one another Make sure that cutlery and dishes do not cover other cu
14. mal soil Crockery and cut Prewash lery Main wash up to 50 C 1 intermediate rinse Final rinse Drying MEMI Select and start a washing programme Programme and pro Degree of soil Type of load Programme description gramme knob posi tion PREWASH Any Partial load tobe 1 cold rinse to prevent food completed later in scraps to bond the day Detergent is not necessary with this programme 1 During the Auto 45 70 programme the soil level of the dishes is given by how cloudy the water is The programme duration and consumptions can change This depends if the appliance is fully or not and on the level of soil on the dishes The appliance adjusts automatically the temperature of the water during the main wash 2 This is the perfect daily programme to clean a not fully load Ideal for a family of 4 persons who only want to load breakfast and dinner crockery and cutlery 3 Test programme for test institutes Please refer to separate leaflet supplied for test data Consumption values Programme 1 Energy in kWh Water in litres AUTO 45 70 ll 7 il 22 30 MIN 60 0 9 9 INTENSIV CARE 70 15 gt Iv B 17 ECO 50 10 117 12 118 PREWASH 0 1 4 1 The digital display shows the programme duration i The pressure and temperature of the water the variations of power supply and the quantity of dishes can change these values SELECT AND START A WASHING PROGRAMME Do these steps to set and start a was
15. nity waste disposal facilities WARNING To discard the appliance follow the procedure e Pull the mains plug out of the socket e Cut off the mains cable and mains plug and discard them e Discard the door catch This prevents the children to close themselves inside the appliance and endanger their lives www aeg electrolux com shop S e e e 117942480 A 122010 CE
16. ns This appliance needs to be earthed according to safety precautions Make sure that the rated voltage and type of power on the rating plate agree with the voltage and the power of the local power supply Always use a correctly installed shockproof socket Do not use multi way plugs connectors and extension cables There is a risk of fire Do not replace the mains cable yourself Contact the Service Force Centre Make sure that the mains plug is accessible after installation Do not pull the mains cable to disconnect the appliance Always pull the mains plug ENVIRONMENT CONCERNS The symbol R onthe product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product The packaging materials are environmentally friendly and can be recycled The plastic com ponents are identified by markings e g gt PE lt gt PS lt etc Discard the packaging materials in the applicable container at the commu
17. omes on when you activate the multitab function Refer to Multitab function Salt Comes on when it is necessary to fill the salt container Refer to Use of g dishwasher salt After you fill the container the salt indicator light can continue to stay on for some hours This does not have an unwanted effect on the operation of the appliance Rinse aid 1 Comes on when it is necessary to fill the rinse aid container Refer to Use ote of rinse aid or 1 When the salt and or rinse aid containers are empty the related indicator lights do not come on while a washing programme operates Programme knob e To switch on the appliance or to set a washing programme turn the programme knob clockwise or counterclockwise The programme marker on the programme knob must agree with one of the washing programmes on the control panel If the programme marker agrees with a washing programme the digital display shows the time duration of the programme If the programme marker does not agree with a washing programme the digital display shows two horizontal bars e To switch off the appliance turn the programme knob until the programme marker agrees with the off indicator Use the programme knob for these operations To set the water softener Refer to Setting the water softener To deactivate activate the rinse aid dispenser Refer to Multitab function Multitab button Press this button to activate deactivate the multi
18. orce Centre replace the water inlet hose with safety valve WARNING Dangerous voltage Water drain hose 1 Connect the water drain hose to the sink spigot and attach it under the work surface This prevents that the waste water from the sink goes back into the appliance Electrical connection i 2 Connect the water drain hose to a stand pipe with vent hole minimum internal di ameter 4 cm Make sure that the drain hose is not bent or squashed to prevent that the water drains does not drain correctly Remove the sink plug when the appliance drains the water to prevent that the water goes back into the appliance A drain hose extension must not be longer than 2 m The internal diameter must not be smaller than the diameter of the hose If you connect the water drain hose to a trap spi got under the sink remove the plastic membrane A If you do not remove the membrane remain A ing food can cause a blockage in the drain hose spigot The appliance has a security feature to prevent that dirty water goes back into the appliance If the spigot of the sink has a non return valve this valve can cause the appliance to drain incorrectly Remove the non return valve CAUTION Make sure that the water couplings are tight to prevent water leakage ELECTRICAL CONNECTION WARNING The manufacturer is not responsible if you do not follow these safety precautio
19. plug from the mains socket and close the water tap Only an authorised service engineer can repair this appliance Use only original spare parts Do not do repairs yourself to prevent injury and damage to the appliance Always contact your local Service Force Centre General safety e Persons including children with reduced physical sensory mental capabilities or lack of experience and knowledge must not use the appliance They must have supervision or instruction for the operation of the appliance by a person responsible for their safety e Obey the safety instructions from the manufacturer of the dishwasher detergent to prevent burns to eyes mouth and throat e Do not drink the water from the dishwasher Detergent residues can stay in your appli ance e Always close the door when you do not use the appliance to prevent injury and not to stumble over the open door e Do not sit or stand on the open door Child safety e Only adults can use this appliance Children must get supervision to make sure that they do not play with the appliance e Keep all the packaging away from children There is a risk of suffocation e Keep all detergents in a safe area Do not let children touch the detergents e Keep children away from the appliance when the door is open Product description Installation AN ake sure that the appliance is not damaged because of transport Do not connect a damaged appliance If necessary contact the
20. ppliance 10 Put the coarse filter A in the microfilter B and push the filters together 11 Put the filter system in position 12 To lock the filter system turn the handle on the microfilter B clockwise until it lock in position 13 Install the lower basket 14 Close the door i Do not remove the spray arms If the holes in the spray arms become clogged remove remaining parts of soil with a cocktail stick External cleaning Clean the external surfaces of the appliance and control panel with a damp soft cloth Only use neutral detergents Do not use abrasive products scouring pads or solvents acetone trichloroethylene etc Frost precautions A CAUTION Do not install the appliance where the temperature is below O C The manufacturer is not responsible for damage because of frost If not possible empty the appliance and close the door Disconnect the water inlet hose and remove water from the water inlet hose WHAT TO DO IF The appliance does not start or stops during operation What to do if A If there is a fault first try to find a solution to the problem yourself If you cannot find a solution to the problem yourself contact the Service Force Centre CAUTION Switch off the appliance before you do the below suggested corrective actions Fault code and malfunction Possible cause and solution e the digital display shows 7 e The water tap is blocked or fur
21. red with limescale The dishwasher does not fill with Clean the water tap water e The water tap is closed Open the water tap e The filter in the water inlet hose is blocked Clean the filter e The connection of the water inlet hose is not correct The hose can be kinked or squashed ake sure that the connection is correct e the digital display shows CL e There is a blockage in the sink spigot The dishwasher will not drain Clean the sink spigot e The connection of the water drain hose is not correct The hose can be kinked or squashed Make sure that the connection is correct e the digital display shows JO e Close the water tap and contact your local Service Force The anti flood device operates Centre The programme does not start e The appliance door is not closed Close the door e Mains plug is not connected in Put in the mains e The fuse has blown out in the household fuse box Replace the fuse e Delay start is set Cancel the delay start to start the programme immedi ately After the check switch on the appliance Set the knob on the same washing programme as before the malfunction The programme continues from the point of interruption If the malfunction shows again contact your Service Force Centre If the display shows a fault code not described in the chart contact your Service Force Centre These data are necessary to help you quickly and correctly e Model Mod e Product number PNC
22. ses energy consumption Three minutes after the end of the programme all indicator lights go off and the digital display shows one horizontal bar Press a button to go back to the end of programme mode Removing the load e First remove items from the lower basket then from the upper basket e There can be water on the sides and door of the appliance Stainless steel becomes cool more quickly than the dishes CARE AND CLEANING WARNING Switch the appliance off before you clean the filters Cleaning the filters CAUTION Do not use the appliance without the filters Make sure that the installation of the filters is correct Incorrect installation will cause unsatisfactory washing results and damage to the appliance If necessary clean the filters Dirty filters decrease the washing results The dishwasher has three filters 1 coarse filter A 2 microfilter B 3 flat filter 0 Do these steps to clean the filters 1 Open the door 2 Remove the lower basket What to do if 3 Tounlock the filter system turn the han dle on the microfilter B approximately 1 4 anticlockwise Remove the filter system Hold the coarse filter A by the handle with the hole 6 Remove the coarse filter A from the microfilter B oe 7 Remove the flat filter C from the bot tom of the appliance 8 Clean the filters below running water 9 Putthe flat filter C in the bottom of the a
23. tab function Refer to the chapter Multitab function Delay start button Use the delay start button to delay the start of the washing programme with an interval between 1 and 19 hours Refer to the chapter Setting and starting a washing programme Start button Use this button to start the washing programme Refer to the chapter Setting and starting a washing programme Digital display The display shows e Adjusted level of the water softener e Activation deactivation of the rinse aid dispenser only with multitab function on Use of the appliance e Programme duration e Remaining time to the end of the programme e End of a washing programme the digital display shows a zero e Number of hours in delay start e Fault codes Function buttons Use the function buttons for these operations e To set the water softener Refer to the chapter Setting the water softener e To cancel the washing programme in progress or a delay start in progress Refer to the chapter Setting and starting a washing programme e To deactivate activate the rinse aid dispenser when multitab function is active Refer to the chapter Multitab function Setting mode The appliance is in setting mode when e One or more phase indicator lights are on e The time duration of the programme flashes in the digital display The appliance must be in setting mode for these operations To set a washing programme To
24. the water hardness in your area If necessary contact your local water SL dness Water hardness SAUL 51 70 gi 125 Si 125 64 88 43 50 76 90 7148 80 53 63 2 9 37 42 65 75 09575 46 52 2 8 295536 51 64 5 1 6 4 36 45 2 7 23 28 40 50 4 0 5 0 28 35 2 6 19 22 Se 358 Sh 38 28 2 2 5 15 18 26 32 BS 3 2 18 22 1 4 11 14 IG 2 215 lah 117 1 3 4 10 i 1183 0 7 1 8 12 1 2 lt 4 lt 7 lt 0 7 lt 5 1 11 1 No use of salt required i You must set the water softener manually and electronically Manual adjustment i The appliance is set at the factory at position 2 1 Open the door 2 Remove the lower basket 3 Turn the water hardness dial to position 1 or 2 refer to the chart Install the lower basket 5 Close the door gt Electronic adjustment The water softener is set at the factory at level 5 i The appliance must be switched off 1 Press and hold function button A Turn the programme knob counterclockwise until the programme marker agrees with the first washing programme on the control panel Use of dishwasher salt ON 2 Release the function button A when the digital display shows the current setting Examples level 5 S level 10 9L 3 Press function button A to change the water softener level Every time you press the button the level increases 4 Turn the programme knob to the off position to save the operation U
25. tlery and dishes Make sure that glasses do not touch other glasses Put small objects in the cutlery basket e Plastic items and pans with non stick coatings can keep water droplets Plastic items do not dry as well as porcelain and steel items e Put light items in the upper basket Make sure that the items do not move N CAUTION Make sure that the spray arms can move freely before you start a washing programme N WARNING Always close the door after you load or unload the appliance An open door can be dan gerous Lower basket Put large and heavily soiled dishes and pans in the lower basket re SOO 0000 VERB 0000 2Ek tear ooo 00000000000 00300000000292 Loading cutlery and dishes The rows of prongs in the lower basket can be flat to load large dishes pots pans and bowls Cutlery basket N WARNING Do not put long bladed knives in a vertical position Arrange long and sharp cutlery hori zontally in the upper basket Be careful with sharp items Use the cutlery grids e Put the grids on the cutlery basket e For larger items use only one of the cutlery grids na A imna aQsaa a alanad wadin FER ana Cor Ueuzaizzili neues aa ueuanua paunan ORE e Put forks and spoons with the handles
26. unterclockwise until the programme marker agrees with the first washing programme on the control panel Release function button A when the display shows the water hardness level Turn the programme knob counterclockwise until the programme marker agrees with the second washing programme on the control panel The digital display shows the current setting for the rinse aid dispenser Gd Rinse aid dispenser deactivated la Rinse aid dispenser activated Press function button A to change the setting The digital display shows the new setting Turn the programme knob to the off position to save the operation i To use normal detergent again DMA ON Deactivate the multitab function Fill the salt container and rinse aid dispenser Adjust the water hardness setting to the highest level Do a washing programme without dishes Adjust the water softener to the water hardness in your area Adjust the rinse aid dosage WASHING PROGRAMMES Washing programmes Programme and pro Degree of soil Type of load Programme description gramme knob posi tion AUTO 45 70 1 Any Crockery cutlery Prewash pots and pans Main wash up to 45 C or 70 C 1 or 2 intermediate rinses Final rinse Drying 30 MIN 60 2 Normal or light soil Crockery and cut Main wash up to 60 C lery Final rinse INTENSIV CARE 70 Heavy soil Crockery cutlery Prewash pots and pans Main wash up to 70 C 1 intermediate rinse Final rinse Drying ECO 50 3 Nor
27. until it stops 2 Hold the upper basket by the handle lift it as far as possible and lower it vertically The upper basket latches into the lower or the upper position Use of detergent USE OF DETERGENT i Q 3 Ifyou use a washing programme with pre Only use detergents powder liquid or tablet that are applicable for dishwashers Follow the data on the packaging e Dosage recommended by the manufacturer e Storage recommendations Do not use more than the correct quantity of detergent to save an environment Do these steps to fill the detergent dispenser 1 Open the lid of the detergent dispenser 2 Fill the detergent dispenser A with de tergent The marking shows the dosage 20 approximately 20 g of detergent 30 approximately 30 g of detergent wash phase put more detergent in the prewash detergent compartment B BET Multitab function 4 Ifyou use detergent tablets put the de tergent tablet in the detergent dispenser A 5 Close the lid of the detergent dispenser Press the lid until it locks into position i Different brands of detergent dissolve in different times Some detergent tablets do not have the best cleaning results during short washing programmes Use long washing pro grammes when you use detergent tablets to fully remove the detergent MULTITAB FUNCTION The multitab function is for combi detergent tablets Th
Download Pdf Manuals
Related Search