Samsung SDZ-370 User`s manual
Contents
1. High Resolution 37X Zoom Color Camera SDZ 370 User s Manual Thank you for purchasing a SAMSUNG CCD CAMERA Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use ENGLISH Thank you for purchasing a SAMSUNG CCD CAMERA Before operating the camera confirm the camera model and proper input power voltage In order to that you can understand this manual thoroughly we ll introduce our model description Ii SDZ 370 SERIES NTSC MODEL PAL MODEL SDZ 370N SDZ 370P m MODEL DESCRIPTION SDZ 370X SIGNAL SYSTEM SIGNAL SYSTEM N NTSC MODEL P PAL MODEL CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with an arrowhead symbol within an equilateral triangle is A intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute arisk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance INFORMATION This equipment has been tested and found to comply with limits for a C2. MANUAL ECRIRE Z1 Interlece Sync Synchronization Internal The Motion Detection function does not work Frequency H 15 734KHz IV 59 94Hz H 15 625KHz I V 50 00Hz Check that MOTION DEF of SPECIAL SETUP menu is OFF Resolution 550 TV Lines Min Color 680 TV Lines Min BAW e Color i t t Min Illumination 0 4 Lux F1 6 50IRE Color 0 02 Lux F1 6 50IRE B W OILS NOKCONECE SIN Y signal 50 dB AGC OFF Weight ON Check the setting of WHITE BAL SETUP menu Video Output CVBS 1 0Vp p 750 The screen flickers continually oom Movement Speer J SEC ide to lele Check that direction of camera turns toward the Sun MAGO ATOMAN RS 485 communication fails Lens Initialize Built in Check the polarity between RS 485 Control Port and RS 485 cable Camera Title ON OFF z angers E 000 gt 485 Control Board Connection Port RS 485 Control Port p Camera ID 256EA Remote only CONNECTION TERMINAL TRX 485 E Day amp Night AUTO COLOR BWIEXT IR Cut Filter CONNECTION TERMINAL TR 485 Gain Control LOW MEDIUM HIGH MANUAL OFF Removable Y S R White Balance ATW AWC MANUALINDOOR OUTDOOR Check the RS 485 Communication establishment initial value BACKLIGHT BLC HLC OFF ppa M we C Shutter Speed AUTO MANUAL A FLK 1 120 0005ec X256 5 425 Communication establishment intial vale A ba KOREAN ESPANOL FRANCAIS ITALIANO DEUTSCH ENGLISH JAPANESE I
3. 256x Verify changes made to the shutter speed by referencing to changes in on screen brightness Press the SET button to complete Image may become unstable if the camera is set to ESC mode and faces a strong fluorescent light Under ESC mode the brightness can be adjusted using the LEFT or RIGHT button O AGC Auto Gain Control For brighter images Position the indicator over AGC using the UP or DOWN button Set AGC to the desired mode using the LEFT or RIGHT button e HIGH Wide range gain value adjustment MEDIUM MEDIUM range gain value adjustment eLOW Narrow range gain value adjustment MANUAL Selecting gain value range 5dB 41dB OFF Disabled MEDIUM SSNR Samsung Super Noise Reduction On screen noise reduction Position the indicator over SSNR using the UP or DOWN button set SSNR to the desired mode using the LEFT or RIGHT button eLOW Low noise reduction MEDIUM Medium noise reduction e HIGH High noise reduction OFF Disabled p SSHR MEDIUM e Changing AGC setting from LOW to HIGH results in greater sensitivity as well as on screen noise Setting AGC to OFF locks SSNR configuration SENS UP This feature ensures clear images at night or under low lighting conditions Position the indicator over SENS UP using the UP or DOWN button Set SENS UP to the desired mode using the LEFT or RIGHT button AUTO Select this mod
4. SAMSUNG TECHWIN CO LTD 42 SUNGJU DONG CHANGWON CITY KYUNGNAM KOREA 641 716 CCTV Camera SDZ 370N SDZ 370P 6400001 2008 4 1 EN 50081 1 1992 EMC Directive 89 336 EEC and 92 31 EEC EN 50130 4 1996 We the undersigned hereby declare that the equipment specified above conforms to the above Directive s Manufacturer Signature Full Name Position Place Date SAMSUNG TECHWIN CO LTD Legal Representative in Europe Han Wang Gm HAN SEUG KIM Signature Full Name QUALITY CONTROL MANAGER Position CHANGWON KOREA 2008 4 1 Place Date SAMSUNG TECHWIN SALES NETWORK SAMSUNG TECHWIN CO LTD 145 3 Sangdaewon 1 dong Jungwon gu Seongnam si Gyeonggi do Korea 462 703 TEL 482 31 740 8151 8 FAX 82 31 740 8145 SAMSUNG TECHWIN AMERICA Inc SAMSUNG TECHWIN EUROPE CO LTD 1480 Charles Willard St Carson CA 90746 UNITED STATES Samsung House 1000 Hillswood Drive Hillswood Business Tol Free 1 877 213 1222 FAX 1 310 632 2195 Park Chertsey Surrey UNITED KINGDOM KT16 OPS www samsungcctvusa com TEL 44 1932 45 5300 FAX 44 1932 45 5325 www samsungtechwin com www samsungcctv com P No Z6806094901A VAN 09 02
5. VIDEO cable to the camera VIDEO output jack The image on the screen is dim Is lens stained with dirt Clean your lens with soft clean cloth Set the monitor to proper condition If the camera is exposed to too strong light change the camera position Troubleshooting Q Specifications The image on the screen is dark SDZ 370N SDZ 370P Note Adjust the contrast feature of the monitor Input Voltage DC 10 8V 13 2V Recommended 12V If you have an intermediate device set the 750 Hi z properly POWER Power Consumption 28W Steady state at 12V f 5 1 W Max Zoom Focus Day amp night motor operating at 12V The camera is not working properly and the surface of the camera is hot Size 1 4 Inch Super HAD color CCD Check that you have properly connected the camera to an appropriate power source CCD Total Pixels 811 H x 508 V 795 H x 596 V e The DAY NIGHT menu does not work 5 E Eure 168 H NU TEENA a 58A Check that AGC of EXPOSURE SETUP menu is OFF PM ia T500mm The SENS UP function does not work i p zooM OFF ON Limit 12x Check that AGC of EXPOSURE SETUP menu is OFF s Angle Field of view H Appr 55 5 Wide to 1 59 Tele V Appr 42 5 Wide to 1 19 Tele Check that SHUTTER of EXPOSURE SETUP menu is A FLK or
6. and Down buttons so that the arrow DWELL TIME You can select the duration time E 3 indicates PRIVACY PAREASEL AREAL about changing the day night mode DAY NIGHT AUTO SETUP AREA MODE ON e 5 7 10 15 20 30 40 60 sec bDWELL TIME 5 SEC IASK COLOR GRAY Mas v DURATION You can select brightness of DURATION FAST NM illumination about changing the day night mode set up the mode using the 4 direction buttons AREA SEL You can select up to 8 MD areas P AREAMODE Determines whether to use the 45 ipm mu aa AA aaa area selected in the AREA SEL and BOTTOM 110 wmm Fast ee a d BW 4 ue Sir the size and position of the area UTERE i Slow 0 8 lux 6lux MASK COLOR Determine area color You can select J E hmmm A X Gray Green Red Blue Black White 5 c EXT This mode allows you to apply a desired filter to external signals Operating Your Camera Q A Notes When using a Video Auto Iris Lens if you set the lens level to low automatic switching between Color and Black amp White may not occur You cannot control the DAY NIGHT menu when AGC in the EXPOSURE menu is OFF At this time the exchange between DAY mode and NIGHT mode operates as like selecting COLOR mode The OSD key does not work for 3 seconds when switching to Color or B W to ensure stable camera operation The camera may focus less well under infrared illumination than unde
7. configurations using this feature Position the indicator over USER PRESET using the UP or DOWN button and then set to ON using the LEFT or RIGHT button Press the SET button to confirm Em cm ZOOM FOCUS POS SETUP PUSER PRESET OFF T TELE WIDE lt NEAR FAR USER PRESET SETUP PRESET NO Up to 128 preset configuratons are b PRESET MO dp Jun supported PRESET CLEAR PRESET NOT DEFINED PRESET SAVE Save configured preset PRESET CLEAR Clear configured preset USER PRESET SETUP PRESET NOE 1 hn gt PRESET SAVE PRESET CLEAR END Revert to the FOCUS SETUP menu END PRESET NOT DEFINED LENS INIT Use the left or right button in the Lens E initialization item to select USER PRESET SETUP Automatic or Manual and press the PRESET NOT 1 Hum SET button to set up the initialization of the lens AUTO The lens is initialized by setting the date reset time can be set from 1 day to 7 days and the lens resets every 24 hours from the set time Manual The Lens will reset when you press the SET button BLEHS INIT MAHUAL END To revert to the main setup menu p EXPOSURE 1 Press the SET button to access the main setup menu and then position the indicator over EXPOSURE using the UP or DOWN button 2 Press the SET button to confirm BRIGHTNESS Use this feature to adjust image brightness Position the indicator over BRIGHTNESS using the UP or DOWN b
8. information is provided to ensure your safety and to prevent any losses financial or otherwise Please read it carefully and use the product accordingly For product inquiries please contact the retail shop where you bought the camera The use of equipment such as an aerial ladder while providing after sales service shall be at your expense Separate the power plug when thunder crashes or lighting flashes This product is support equipment for surveillance system Therefore we can t compensate for material loss and or personal injuries by robbery fire natural disaster or something like this type Ignoring this information may T 7 result in material loss and or anong pis namatay serious personal injuries including 4 b banig logs andona death 7 a Indicates Never Allowed Correct Disposal of This Product Waste Electrical 8 Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local govern
9. right button in the START ZOOM item to select the zoom position from 1x to 37x to be returned after the SMART ZOOM action is over TARGET ZOOM Use the left or right button in the TARGET ZOOM item to select the zoom position from 1x to 37x to be used during MOTION DETECTION e DWELLTIME Use the left or right button in the DWELL TIME item to select a time between 5 and 60 seconds for the dwell time before the zoom is returned to the START ZOOM position 5 7 10 15 20 30 40 60 sec C TOP BOTTOM LEFT RIGHT You can adjust the size of the area gt Notes k Tips on Using the Motion Detection Feature e The feature may not function properly under flickering light conditions The camera interprets sudden changes in lighting and subsequent change in brightness of an object as motion With the feature enabled other algorithms may require additional time to operate than V usual 3 CNotes This system does not guarantee prevention of fire or theft The manufacturer shall not be held responsible for any accident or damage incurred Connect an external alarm device to MD Out on back of the camera 1 Press the SET button to access the main setup manu and then position the indicator over FOCUS using the UP or DOWN button 2 Press the SET button MODE You can select the most suitable zoom mode Move the arrow indicator to MODE using UP or DOWN button P MODE OHE PUSH Select
10. 0h 00h 00h AFh CHECK SUM Focus Far Function Move focus lens to far direction Command Packet A0h CAM ID HOST ADDR 0100h 00h 00h 00h 00h AFh CHECK SUM Return Packet A0h CAM ID HOST ADDR 0100h 00h 00h 00h 00h AFh CHECK SUM Focus Near Function Move focus lens to near direction Command Packet A0h CAM ID HOST ADDR 0200h 00h 00h 00h 00h AFh CHECK SUM Return Packet A0h CAM ID HOST ADDR 0200h 00h 00h 00h 00h AFh CHECK SUM Zoom Wide Function Move zoom lens to wide direction Command Packet A0h CAM ID HOST ADDR 0040h 00h 00h 00h 00h AFh CHECK SUM Return Packet A0h CAM ID HOST ADDR 0040h 00h 00h 00h 00h AFh CHECK SUM Zoom Tele Function Move wide lens to tele direction Command Packet A0h CAM ID HOST ADDR 0020h 00h 00h 00h 00h AFh CHECK SUM Return Packet A0h CAM ID HOST ADDR 0020h 00h 00h 00h 00h AFh CHECK SUM ZOOM Direct Function Move ZOOM lens to specific position directly Command Packet A0h CAM ID HOST ADDR 00FFh P1 P2 P3 00h AFh CHECK SUM Return Packet A0h CAM ID HOST ADDR 00FFh P1 P2 P3 00h AFh CHECK SUM Parameter P1 P2 OPTICAL ZOOM 0000h 06EAh P3 DIGITAL ZOOM 256 10 Ratio 1 ex D ZOOM 1 1x P3 E7h 256 10 11 1 Ratio 11 means 1 1x D Z00M 2 0x P3 7Fh 256 10 20 1 Ratio 20 means 2 0x AF Stop Function Stop zoom amp focus lens moving Command Packet A0h CAM ID HOST ADDR 0000h 00h 00h 00h 00h AFh CHECK SUM Return Packet A0h CAM ID HOST ADDR 0000h 00h 00h 00h 00h AFh CHECK SUM One push AF Function Unconditionally execute auto focu
11. AUTO and press the SET button to confirm Increase or decrease optical zoom ZOOM or digital zoom D ZOOM positions using the UP or DOWN button while verifying the changes on screen Enabling D ZOOM ON means that digital 1iTEE WIDE zoom will activate once optical zoom E ends Focus is automatically adjusted with moving zoom e ONE PUSH Focus is automatically adjusted just once ZOOM FOCUS POS SETUP after zoom position is changed Select ONE PUSH and press the SET button to confirm Increase or decrease optical zoom ZOOM or digital zoom D Z00M EAR positions using the directional buttons while verifying the changes on screen Press the SET button once desired image quality is obtained ZOOM POS SETUP 1 TELE WIDE e MANUAL Select MANUAL and press the SET button dg to confirm Increase or decrease optical Z00M FOCUS POS SETUP zoom ZOOM or digital zoom D ZOOM positions using the directi onal buttons while verifying the changes on screen Press 1iTEE WIDE the SET button on ce desired image quality is obtained Focus can be manually adjusted independent of moving zoom ZOOM TRK Select ON for the SMART ZOOM item in the MOTION DETECTION menu and press SET button to change the settings for the SMART ZOOM function Use the left or right button in the ZOOM item to select AUTOTRACK or TRACK and press SET button to activate the zoom action focus function AUTOTRACK Zooming in while d
12. F V REV OFF the screen SHARPNESS ON SHARPNESS As you increase this value the picture ED Spa outline becomes stronger and clearer SHARPNESS SETUP P LEVEL 16 aan END e COLOR Adjusting this value affects the chroma level only the burst level is unaffected END evert back to the USER PRESET menu DISPLAY Use this feature to designate a name for the camera which will display on the monitor screen CAM TITLE Press the SET button to display the main setup menu and move the arrow indicator to CAM TITLE using the UP or DOWN button Set CAM TITLE to ON using the LEFT or RIGHT button Notes If the CAM TITLE feature is set to OFF the name will not displayed in the monitor DISPLAY SETUP Press SET button CAMERA TITLE SETUP ABCDEFGHIJKLM NOPQRSTUVWXYZ 0123456789 lt gt A gt CLR POS END You can enter up to 20 characters a Move the cursor to the character entry field using the LEFT or RIGHT button b Use UP DOWN LEFT and RIGHT buttons to select a desired character c Press the SET button to confirm selection of the blinking character The character is then saved and the cursor in the entry field moves to the next position d Repeat steps a through c until the desired name has been entered Correcting Mistakes Move the cursor th CLR and press the SET button to clear the entire entry To modify one character use LEFT or R
13. IGHT to position the cursor above the character to be modified and Click the SET button after selecting the character to enter Enter a title move the cursor to POS and press the SET button The entered title appears on the screen Select the position to display the title on the screen by using the 4 direction butons and press AS the SET button When the position is determined select A FRONT DOOR DILE Hi A e CAM ID Displays camera ID on top left corner of the screen CAM INFO Displays camera information on screen e MOTION ALARM You can toggle the use of the camera alarm Z00M MAG Use this feature to display the current zoom magnification level on screen Position the indicator over ZOOM MAG using the UP or Down button Then set to ON using the LEFT or RIGHT button LANGUAGE You can select the menu language according to your requirements Korean ESPANOL FRANCAIS ITALIANO DEUTSCH ENGLISH Japanese Chinese Select this to save the SPECIAL menu settings and return to the SPECIAL menu To finish setup menu If you have trouble operating your camera refer to the following table If the guidelines do not enable you to solve the problem contact an authorized technician Nothing appears on the screen Check that the power cord and line connection between the camera and monitor are fixed properly Check that you have properly connected
14. SUM Return Packet A0h CAM ID HOST ADDR 0008h 00h 00h 00h 00h AFh CHECK SUM OSD Menu Down Function Move OSD arrow to down Command Packet A0h CAM ID HOST ADDR 0010h 00h 00h 00h 00h AFh CHECK SUM Return Packet A0h CAM ID HOST ADDR 0010h 00h 00h 00h 00h AFh CHECK SUM OSD Menu Left Function Move OSD arrow to left Command Packet A0h CAM ID HOST ADDR 0004h 00h 00h 00h 00h AFh CHECK SUM Return Packet A0h CAM ID HOST ADDR 0004h 00h 00h 00h 00h AFh CHECK SUM OSD Menu Right Function Move OSD arrow to right Command Packet A0h CAM ID HOST ADDR 0002h 00h 00h 00h 00h AFh CHECK SUM Return Packet A0h CAM ID HOST ADDR 0002h 00h 00h 00h 00h AFh CHECK SUM OSD Menu Set Functio Move to inside menu Command Packet A0h CAM ID HOST ADDR 0100h 00h 00h 00h 00h AFh CHECK SUM Return Packet A0h CAM ID HOST ADDR 0100h 00h 00h 00h 00h AFh CHECK SUM OSD Menu ESC Function Move to upper menu Command Packet A0h CAM ID HOST ADDR 0200h 00h 00h 00h 00h AFh CHECK SUM Return Packet A0h CAM ID HOST ADDR 0200h 00h 00h 00h 00h AFh CHECK SUM COLOR CCD CAMERA 44 User s Manual COLOR CCD CAMERA 45 User s Manual DECLARATION OF CONFORMITY Application of Council Directive s Manufacturer s Name Manufacturer s Address European Representative Name European Representative Address Equipment Type Environment Model Name Beginning Serial NO Year of Manufacture Conformance to 89 336 EEC SAMSUNG TECHWIN CO LTD
15. e UP or DOWN button Each pressing of the UP or DOWN button moves the indicator to the next or previous feature Move the arrow indicator to the desired feature item 3 Change the status of the selected feature using the LEFT or RIGHT button 4 When completed move the arrow indicator to EXIT and press the SET button e Features marked with a 4 have an accessible submenu Access the submenu by pressing the SET button Use the White Balance function to adjust the screen color 1 When the SETUP menu screen is displayed select White Bal by using the Up and Down buttons so that the arrow indicates White Bal 2 Select a desired mode using the Up and Down buttons p WHITE BAL 3 Select one of the following 5 modes as appropriate for your purpose SATW Select this when the color temperature is between 1800 K and 10500 K S INDOOR _ Select this when the color temperature is between 4500 K and 8500 K OUTDOOR Select this when the color temperature is between 1800 K and 10500 K sodium light inclusion AWC gt SET To find the optimal setting for the current luminance environment in this mode set the point the camera towards a sheet of white paper and press the SET button If the environment changes readjust it O MANUAL Select this to fine tune White Balance manually Set White Balance first by using the ATW or AWC mode After that switch to MANUAL mode fine tune the White Balance and t
16. e for use in night time or under low lighting conditions OFF Disabled gt SEHZ UP Once AUTO mode is set the user can configure Sens Up limit by increasing decreasing the shutter speed e g X2 X4 X32 X64 X128 X256 Enabling Sens Up increases camera sensitivity and may result in additional noise and or other phenomenons This is normal e MASKTONE Determine the transparency of selected area as controlling number from 0to 3 END Select this to save the PRIVACY menu settings and return to the SPECIAL menu C DAY NIGHT You can display pictures in color or black and white Sk ee 1 Press the SET button to access the main setup menu and then position the indicator over SPECIAL using the UP or DOWN button When the SETUP menu screen is displayed select DAY NIGHT by using the Up and 2 Press the SET button to confirm Down buttons so that the arrow indicates DAY NIGHT PRIVACY Hide an area you want to hide on the screen Select a desired mode using the Left and Right buttons according to the picture display you want e COLOR The picture is always displayed in color e BW The picture is always displayed in black and white AUTO The mode is switched to Color in a normal environment but Switches to B W mode when ambient illumination is low To set up the sswitching time or speed for AUTO mode press the SET button When the SPECIAL menu screen is displayed press the Up
17. eciding or adjusting the status of the focus TRACK Zooming in with no relevance to the focus OFF Only the zoom lens moves gt 200M TRE AUTO TRACK ZOOM SPEED Configure zoom tracing speed using this feature Position the indicator over ZOOM SPEED using the UP or DOWN button and then set to desired mode using the LEFT or RIGHT button p 200M SPEED FAS e FAST To move zoom fast MEDIUM To move zoom at medium speed SLOW To move zoom slowly The Z00M SPEED mode cannot be used if MODE is set to AUTO and Z00M TRK is ON D ZOOM Configure magnification limit from x2 x12 using this feature Position the indicator over D ZOOM using the UP or DOWN button Set D ZOOM to ON and press the SET button to confirm P n z on Set ZOOM LIMIT to the desired level using the mm 2 LEFT or RIGHT button D ZOOM LIMIT SETUP gt LIMIT X2 END When the DIS is enabled you cannot use the D Z00M ZOOM POS INIT Moves to the controlled ZOOM position when the power truned on and is a function of the initial ZOOM position control Baloi POS INIT AUTO AUTO lf you tum the power off and on the zoom magnification level is set to the previous level that was set before the power went off MANUAL The zoom magnification level can be set from 1x to 37x The zoom postion is saved after 5 seconds when you set zoom function USER PRESET Preset user designated
18. ecifications shown on the right Attach the bracket to the top of the camera Use screws included in the package or their equivalent less than 6mm Otherwise the bracket may not assemble to the camera properly Key Buttons Following buttons control zoom focus and auto focus functions WIDE button To widen the view ZOOM OUT TELE button To close in on a far object ZOOM IN F NEAR button To see a near object clearly F FAR button To see a far object clearly Pressing the SET button locks the zoom control function of these buttons and prompts the main setup menu Main setup menu can be navigated using these buttons SET To access the main setup menu UP TELE button To move the arrow indicator to up DOWN WIDE button To move the arrow indicator to down LEFT F NEAR button To move the arrow indicator to left RIGHT F FAR button To move the arrow indicator to right Power Input Terminal Power supply terminal DC12V 10 Power LED Illuminates when power is supplied Q Video Output Jack Used to connect an external video monitor in jack RJ 45 JACK Terminals such as RS 485 communications MD OUT ZOOM and FOCUS EX_DN are areincluded Connect Video Out Jack to the monitor s Video In jack as shown below CCD Camera 3 Monitor Connection methods may vary depending on the video equipment Please refer to the model specific instruction manual Connect cables
19. er to prevent signal reduction the termination resistance of the 2 end units which are the distant paths for camera and controller to be connected on the RS485 interface should be connected As the termination resistance is built in the camera whether to make the termination resistance valid or invalid is selected with the TERMINATION See the connection diagram for determining to which device the termination resistance will be connected to Set up the termination resistance in the dark products The installation distance of the product for the termination resistance setting should be less than 1 2 Km Maximum cable length is 1 2 Km according to the RS 485 standards CONTROLLER CONTROLLER COLOR CCD CAMERA 33 User s Manual RET PKT You can choose whether to send an ACK signal when the communication control command is issued to the camera le D e If Camera is controlled by the Vicon Controller function button may not work properly IMAGE ADJ Includes image quality or special function factors p IMAGE ADI When the SETUP menu screen is displayed select IMAGE ADJ by using the Up and Down buttons so that the arrow indicates IMAGE ADJ Select a desired mode using the Up and Down buttons H REV You can flip the picture horizontally on the screen IMAGE SETUP V REV You can flip the picture vertically on f gt H REV OF
20. esired mode using the Left and Right BLC SETUP button and press the SET button E DER e Select BLC to adjust the area to be enhanced and BOTTOM Ed enhancement level RIGHT 70 sn Select HLC to adjust the HLC MASK COLOR and LEVEL HLC SETUP gt LEVEL LOW MASK COLOR 5 UNAN nit END Q 9 Notes You cannot use the BLC mode when MANUAL or A FLK mode in SHUTTER menu is selected Since the following symptoms may occur according to the ambient illumination when BLC is selected set it to OFF Color or screen changes unnaturally Noise appears in the bright part of the screen Since the performance of the BLC function may be affected by the area of the bright part of the screen optimize the installation angle for the best BLC performance e If you increase LIMIT the screen display may be distorted For high performance of BLC function We recommend that you set IRIS to AUTO in the EXPOSURE setup Activating BLC may cause the camera to repeat the Auto Focus operation depending on lighting conditions It is recommended that you use the Focus Setup menu in One Push or Manual mode Smart Zoom and BLC cannot be used in conjunction with each other e Setting up BLC and then Smart Zoom automatically cancels BLC e Setting up Smart Zoom and then BLC automatically cancels Smart Zoom COLOR CCD CAMERA 18 User s Manual Motion Detection This product has a feature that allows you to observe move
21. focus auto iris and zoom functions pbig 3l Samsung Super Noise D ction The high performance W N DSP chip dramatically reduces the gain noise in digital image precessing producing clear sharp images in low lighting environments p g Y 7 Fi ir Quality under Ultra Low Lighting 1 4 high density CCD allows the user to capture bright high quality images under ultra NG T RS as JN are provided bA wy NG Nu Vo 8 Night a The camera automatically determines whether itis night time or day time selecting operating mode automatically The camera operates in color mode during day light conditions and BW mode in night conditions for clearer identification phdg v 7 Disibigita Image Stabilizer Pyya The DIS function can compensate for vibration of the camera so it helps you obtain more stabilized image under the shaking conditions D n Detection alert signal to the process used in conjunction with an optiona provide effective surveill ka 7 Y OM SHARP OTION DETECTION and PRIVACY functions stages to preserve the environment and is taking a number of steps to provide customers with more environment friendly products The Eco mark represents eco Samsung Techwin s will to create environment friendly products and indicates RoHS compliant that the product satisfies the EU RoHS Directive C Samsung Techwin cares for the environment at all product manufacturing This
22. he ground MD Motion Detection Output Signal Level less than 10mA When using the MD function the GND should be connected to the frame ground Do not simultaneously connect the RS 485 communication line when you use voltage control ZOOM and FOCUS using the RECEIVER BOX SRX 100B Match the communication setup between devices when you use the wired controller SCC 101 or SCC 3100A T WEM _ SCC 101 fixed SCC 3100A Factory Default MODE Serial Serial Data Bit 8 bit 8 bit Bit Sec 9600bps 9600bps Contact an authorized Parity EVEN NONE technician for CAM ID NO 0 1 255 inspection RETURN PACKET ENABLE See the SCC 3100A manual COLOR CCD CAMERA 13 User s Manual e ATW WHITE BAL e OUTDOOR INDOOR BACKLIGHT e OFF e BLC e HLC MOTION DET e OFF ON MODE ZOOM TRK ZOOM SPEED FOCUS D Z00M e ZOOM POS INIT USER PRESET eLENSINIT END e BRIGHTNESS e IRIS SHUTTER EXPOSURE e AGC SSNR SENS UP END PRIVACY DAY NIGHT DIS SPECIAL eCOMMADJ eIMAGEADJ DISPLAY END RESET EXIT Use the five buttons on back of the camera UP button 1 Press the SET button for 2 seconds Short pressing the button activates the AUTO FOCUS Main setup menu is displayed on the monitor screen Select feature using the UP or WHITE BAL ATH Change the status using the DOWN button LEFT or RIGHT button 2 Select the desired feature using th
23. hen press the SET button Ep WHITE BAL MANUAL SETUP RED 147 dnt BLUE 93 imm P END Press SET to Return White Balance may not work properly under the following conditions In this case select the AWC mode When the color temperature of environment surrounding the subject is out of the control range When the ambient illumination of the subject is dim If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically the White Balance operation may become unstable This camera is designed so that it delivers a distinctive subject and background at The same time even when the subject is in backlight unlike conventional cameras By adopting a proprietary W IV DSP chip 1 When the SETUP menu screen is displayed select BACKLIGHT by using the Up and Down buttons so that the arrow indicates BACKLIGHT p BACKLIGHT 2 Select a desired mode using the Left and Right buttons depending on the camera pupose C BLC Enables a user to directly select a desired area from a picture and to view the area more clearly HLC High Light Compensation If there is a high light installed in dark environment such as an apartment parking garage or gas station entrance removing the high light makes it possible to view car license plates efficiently HLC MASKING AREA Operating Your Camera OFF Deactivates the BACKLIGHT function 3 Select a d
24. lass A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WARNING Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment WARNING To prevent electric shock and risk of fire hazards Do NOT use power sources other than that specified Do NOT expose this appliance to rain or moisture This installation should be made by a qualified service person and should conform to all local codes e Features Warnings amp Cautions e Components and Accessories Overview Connection E Connecting to Monitor E Connecting to Power Wi Connecting to 8P Control Terminal Operating Your Camera E Menu Configuration E Menu Setup WHITE BALANCE BACK LIGHT MOTION DETECTION Troubleshooting Specifications STW Protocol pads ami Optica Zoom Aa built in SDZ 370 optical zoom lens is a highly durable component It features auto
25. ment office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal on f 4 amp Use only under temperature conditions between May lower image quality 10 C and 50 C Provide good ventilation when using in high temperature conditions Severe lighting changes or flickering may hinder The lens is the most important component of normal camera operation the camera Be careful not to smear it with fingerprints May cause a product malfunction lege May cause a product malfunction Wipe dry any Radioactivity exposure may damage the CCD liquids Liquids may contain minerals that are corrosive to electronic components C Notes Exposure to a spotlight or an object emitting strong light may cause smear or blooming Ensure that the power source complies with normal specifications before supplying it to the camera 37x Zoom Color Camera SDZ 370 Instruction Manual 8 PIN CABLE ASSY Tripod Mounting Bracket Screw Hole Used to fix tripod mounting bracket on top of the camera Tripod Mounting Hole Used to install the camera on an optional tripod 114 20 UNC 20 THREAD The tripod must be equipped with screws with PDI rar T sp
26. ments of objects in 4 different areas on the screen and the words MOTION DETECTED appear on the screen when movement is detected hence a single individual can conduct supervision efficiently The camera detects an object s movement by sensing disparity of outline and level of brightness and color The camera receives detection signal from MD output terminal MD SETUP gt AREA SEL AREAL AREA MODE ON 1 AREA SETUP PTOP Z mumu BOTTOM 6 um LEFT 3 Mmmm RIGHT 6 nmm END SENSITIVITY LOW SMART ZOOM ON 1 END Please press the SETUP button OFF MOTION DETECTION mode is cancelled ON Any motion in the selected areas is observed AREA SEL You can select the area you wish to observe from the 8 area AREA MODE Determines whether to use the MD area selected in SENSITIVITY SENSITIVITY You can select up to 8 MD areas When SENSITIVITY number is high motion detection sensitivity is increased to recognize even small movement SMART ZOOM SETUP gt START ZOOM 1 TARGET ZOO 5 DWELL TIME 5 SEC SMART ZOOM Smart zoom is operated in connection with MOTION DETECTION When the SMART ZOOM function is ON while the MOTION DETECTION mode is ON the zoom goes to the TARGET ZOOM position once motion is detected Once the zoom action is finished and DWELL TIME has passed the zoom returns to the START COLOR CCD CAMERA 19 User s Manual Z00M position START ZOOM Use the left or
27. r normal illumination Since the camera may not focus as well under infrared illumination at night as it does under normal illumination install an Extra low Dispersion Lens to obtain sharp pictures The brightness of illumination is changeable by installed environment DIS The DIS mode can compensate for vibration of the camera SPECIAL SETUP PRIVACY OFF DAYANIGHT COLOR gt DIS OFF COMM ADJ C Notes When DIS is operating D Z00M does not operate COMM ADJ Communication Adjustment This function sets up the camera communication status when controlling the camera through an COMMUNICATION SETUP gt PROTOCOL STW CAM ID minimi i BAUD RATE 9600 external control device PAUD PATEE 3600 TERMINATON RET PKT END OFF DISABLE When the SPECIAL menu screen is displayed press the Up and Down buttons so that the arrow indicates COMM ADJ Set up the mode using the 4 direction buttons e CAM ID Determines the camera s identification number COLOR CCD CAMERA 32 User s Manual between 0 and 255 Protocol Select the communication PROTOCOL STW PELCO D PELCO P BOSCH HONEYWELL VICON AD SEC PANASONIC e BAUDRATE Youcan select 2400 4800 9600 19200 38400 57600 1 15200 bps e UART MODE You can select NONE EVEN or ODD for the parity bits e TERMINATION Function that sets the resistance at the end of RS 485 communications k Setting Termination Resistance In ord
28. s Command Packet A0h CAM ID HOST ADDR 0045h 00h 00h 00h 00h AFh CHECK SUM Return Packet A0h CAM ID HOST ADDR 0045h 00h 00h 00h 00h AFh CHECK SUM COLOR CCD CAMERA 40 User s Manual COLOR CCD CAMERA 4D User s Manual Function Save current user preset configuration information Command Packet A0h CAM ID HOST ADDR 0003h CHECK SUM Return Packet A0h CAM ID HOST ADDR 0003h CHECK SUM Parameter P1 00h USER PRESET 1 8Oh USER PRES ET 128 Function Execute selected user preset Command Packet A0h CAM ID HOST ADDR 0007h CHECK SUM Return Packet A0h CAM ID HOST ADDR 0007h CHECK SUM Parameter P1 00h USER PRESET 1 80h USER PRES ET 128 Function Clear selected user preset Command Packet A0h CAM ID HOST ADDR 0005h CHECK SUM Return Packet A0h CAM ID HOST ADDR 0005h CHECK SUM Parameter P1 00h USER PRESET 1 80h USER PRES ET 128 Display OSD menu on the screen User Preset Save User Preset Exec User Preset Clear Function Clear OSD menu and save current menu setup Command Packet A0h CAM ID HOST ADDR CHECK SUM Return Packet A0h CAM ID HOST ADDR CHECK SUM P1 00h ON Parameter 01h OFF OSD Menu On Off STW Protocol Command Description OSD Menu Up Function Move OSD arrow to up Command Packet A0h CAM ID HOST ADDR 0008h 00h 00h 00h 00h AFh CHECK
29. tem CameralD BAUD RATE UART MODE RET PKT L Gu CHINESE total 8 language Initial value 1 9600 8 NONE 1 DISABLE Motion Detection ON OFF Control Output RS 485 2400 4800 9600 19200 38400 5 7600 1 15200bps We recommend that you make ground connect between camera and controller in order to SSNR WO GT ntaj 7m Privacy Function ON OFF 8 Zones maintain safety communication control TE ONO MIRROR ON OFF DIS ON OFF PRESET 128 Positions PROTOCOL STW PELCO D PELCO P SEC PANASONIC VICON AD HONEYWELL BOSCH Operating Temperature Humidity 10 C to 50 C 20 to 80 RH Storge Temperature Humidity 20 C to 60 C 20 to 95 RH Dimension 67 6 W X67 6 H X124 7 D mm Weight 450g COLOR CCD CAMERA 38 User s Manual COLOR CCD CAMERA 39 User s Manual STW Protocol Command Description Command Name Byte1 Byte2 Byte3 Byte4 Il Byte5 Byte 6 Byte7 Byte8 Byte9 Byte10 Byte11 Command Packet STX CAMID HOST ADDR CAMMAND DATA3 DATA4 DATA5 DATA6 ETX CHECKSUM Return Packet STX CAM ID HOST ADDR CAMMAND DATA3 DATA4 DATA5 DATA6 ETX CHECKSUM Checksum CHECKSUM CALCULATION UNARY OPERATION OF SUMMATION FROM BYTE2 TO BYTE EX CHECKSUM BYTE2 BYTE3 BYTE8 BYTES Reset Function Reset all data to factory default value Command Packet A0h CAM ID HOST ADDR 000Fh 00h 00h 00h 00h AFh CHECK SUM Return Packet A0h CAM ID HOST ADDR 000Fh 00h 0
30. utton Then increase or decrease brightness level using the LEFT or RIGHT button while verifying the changes on screen Set END once desired level is obtained P BRIGHTHESS FER nmm UT C IRIS Set IRIS to AUTO or MANUAL Position the indicator over IRIS using the UP or DOWN button and then select the desired iris mode using the LEFT or RIGHT button gt IRIS AUTO AUTO The iris is automatically activated upon illumination e MANUAL Manual iris configuration Set IRIS to MANUAL using the LEFT or RIGHT button and then press the SET button Increase or decrease iris level using the LEFT or RIGHT button while verifying the changes on screen IRIS MANUAL SETUP MIRISVAL FL6 END O SHUTTER Control image brightness by adjusting shutter speed Position the indicator over SHUTTER using the UP or DOWN button Then select the desired shutter mode A FLK ESC MANUAL using the LEFT or RIGHT button p SHUTTER A FLK NTSC 1 100 PAL 1 120 Flicker free mode e ESC Automatic shutter speed setting optimal Auto operation is possible only when the IRIS is set to MANUAL MANUAL Manual shutter speed setting If you choose MANUAL select the optimal SE shutter speed SHUTTER MANUAL SETUP In MANUAL mode the optimal shutter speed DSHUTTER VAL 1 60 needs to be designated Select from 1 60 to END 1 120 000 NTSC or from 1 50 to 1 120 000 PAL Sens Up mode can be configured manually 2x to
31. with the unit powered down e Set the 750 Hi Z selection switch as shown below if you have an intermediate device CCD Camera N Intermediate End monitor Connection Connecting to Power DC Power Type DC 12V 500mA Use DC 12V 500mA power source for SDZ 370N P Power Input Terminal 3 Notes Connect the power once the installation is complete The wire is polarized Match and terminals properly Connecting to 8P Control Terminal The camera can be controlled by using external controllers like a Remote controller RS 485 Communication SCC 3100A 8 Pin CABLE ASSY 8P Control Terminal Configuration Number Name Cablecolor Description Number Name Cable color Description 1 Z00M ORANGE 5 GND BLUE 2 FOCUS WHITE ORANGE 3 COM GREEN 4 MDOUT WHITE GREEN EXDN WHITE BLUE External D N 485 BROWN RS 485 communication 485 WHITE BROWN RS 485 communication clu a COLOR CCD CAMERA 12 User s Manual Comnector Function Signal Level Vo 46V HAN Tele com Z00M l COM Wide RDUM 46V HAN Far COM FOCUS pm l Near 6V 12V COM com 30V MD ov 5 0 5sec There is mation 0 Thereisno motion DAY mode DAN terminals must be OPEN to external signals EX DN Do not input voltage l NIGHT mode D amp N terminal must be connected to t
Download Pdf Manuals
Related Search