Scytek electronic 100RS Product manual
Contents
1. E LECTRONICS ASTRA 300RS REMOTE START WITH KEYLESS ENTRY AUTOMATIC TRANSMISSION ONLY PRODUCT MANUAL Eimited Lifetime Warranty This vehicle Remote Start system is warranted to the original purchaser to be free from defects in material and workmanship The manufacturer will repair or replace at its option and free of charge for the first twelve 12 months any part that proves defective in material or workmanship under normal installation use and service provided the product is returned to the manufacturer freight prepaid After the first 12 month war ranty period there will be a maximum service charge of 25 00 per calendar year if required for repair and or replacement of any defective parts A copy of the original purchase and installation receipt must accompany any products returned for warranty service Warranty is limited to defective parts and or replacement parts only and excludes any incidental and consequential damages connected therewith The manufacturer of this theft deterrent system makes no warranty against the theft of the vehicle or its contents This warranty is not to be construed as an insurance policy against loss WARRANTY OF INSTALLATION LABOR REMOVAL AND RE INSTALLATION CHARGES ARE NOT THE RESPONSIBILITY OF THE MANUFACTURER Note This Warranty is voided if the product was not installed by an Authorized ScyTek Dealer SAKEMM Starter doesn t start and parking lights flash 3 Times2. Green wire LOCK Positive Trigger additional 2 relays reqiured Blue wire LOCK Green wire UNLOCK Door Lock wire FACTORY DOOR LOCK Door Unlock wire MODULE DOOR LOCK SWITCH Adding Actuators Green wire AFTER MARKET LOCK MOTORS 15 FUSE 12V Blue wire UNLOCK Astra 300RS Page 11 Wiring Diagram Brown Ignition 2 Yellow Ignition 1 Orange Accessory Violet Starter Out Red Battery 1 Red Battery 2 Starter Harness Red 12v In White Parking Light Out Black Ground in Astra 300RS White Violet Factroy Disarm Out Blue Orange Ground When Running Out Brown White Horn Out Gray Trunk Release Out White Black Hood Trigger In Green White Brake Light In Black Gray RPM In Orange Starter Disable Factory Rearm Ign 3 Main Harnes Blue Unlock Green Lock Door Lock White Blue Red White Antenna Mobilink LED light Valet Switch Bypass Module Port ScyTek Electronics 11627 Cantara Street North Hollywood CA 91605 www scytek net Page 12 Astra 300RS 8 2012
3. Engine RPM not detected check tach wire and or perform tach learn procedure Hood Trigger is active hood is open wire is shorted to ground or pin switch is defective 8 Times Brake Trigger is active Brake switch input is shorted to ground or incorrect 5 Times Unit is in Valet service mode and start is disabled VALET SWITCH lt Remote Transmitter Description Button 1 Button 3 The Astra 300 is supplied with two 4 button Remote Transmitters used to control system operations Button 1 Locks the doors and when held for 2 seconds activates the system s Panic feature Button 1 also locks the doors when the system is in Valet Mode Button 2 Unlocks the doors Button 2 also unlocks the doors when the system is in Valet Mode Button 3 Activates the Auxiliary 1 output This output will remain on for as long as the button is pressed Button 4 Activates and deactivates the remote start Jumper Selection Carefully separate the top and bottom halves of the main unit case Once the cover is removed the parking light polarity jumper will be visible next to the parking light relay Set the jumper for the correct polarity output as described below then reassemble the main unit case Parking Light Output Selects the polarity for the output of the on board Parking Light relay Left Pin and Center Pin negative Right Pin and Center Pin positive Astra 300RS Page 3 System
4. 5 times The horn will provide three chirps indicating that you have entered Programming 3 Press the valet switch the number times equal to the System Parameter you want to change The horn will chirp each time the valet switch is pressed 4 Within 5 seconds press the transmitter button corresponding to the desired operating mode for that System Parameter The horn will chirp to indicate the setting 1 chirp Button 1 2 chirps Button 2 3 chirps Button 3 5 When you are finished turn off the ignition to save the changes Default Reset Following this procedure will set all System Programming Parameters to factory default settings 1 Enter System Programming 2 Press Transmitter Button 3 The horn will chirp 6 times indicating that the reset signal was received All System Programming parameters now set to factory default settings The Valet Mode is off 3 Turn off ignition Programmable System Options The following is a description of the programming options of the system Some of the program branches control more than one option and may require accessing a particular branch number twice in order to program all desired fea tures 3 Lock Unlock Chirps Selects between normal and silent operation 5 Extended Parking Lights When Enabled upon Disarming Parking lights will turn On for 30 seconds or until the Dome light turns Off Reset Mobilink Galaxy Mobile module 6 Ignition Door Locking V
5. Operation 30085 Adding Replacing One Way Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system have all desired transmitters ready and follow the steps below Note Up to 4 transmitters can be programmed to operate the system To erase any previously stored transmitter codes be sure to program all 4 transmitter memory locations To program the transmitter s 1 Turn on the ignition key On Off On Off and back On The Horn will flash 3 times 2 Press and hold the Valet switch for 5 seconds The Horn will flash 5 times The LED will illuminate 3 Press Button 1 on the first transmitter The horn will flash once 4 Repeat steps 3 for each transmitter up to 4 5 Turn off the ignition key Battery Replacement Your Remote Transmitter uses a 12 volt alkaline battery type 23A which will require replacement in time Depending on the amount of use the battery may last up to six months or more before it needs replacement When the battery needs replacing the system s operating range will decrease the transmitter LED may not be as bright In order to change the battery first remove 2 screws from the back of the transmitter and separate the top and bottom halves of the case While replacing the battery make sure that the positive and negative terminals are positioned cor rectly then carefully reassemble the transmitter case Panic Mode In the event of an em
6. advanced software routine without requiring connection to the vehicle s tachometer Tachless operation may not be compatible with some vehicles or in severe temperatures in which case the tach wire must be connected 21 Remote Start Program This dual program branch sets the engine mode for Gas or Diesel and learns the vehicle s RPM threshold Learning the RPM threshold automatically selects the RPM monitor mode For installation into a diesel equipped vehicle first set the engine type to diesel before learning RPM Tach Monitor Mode Monitors the vehicle s tach wire or a fuel injection wire in real time to determine engine status and adjust starter crank time automatically If programmed for Tach Monitor the vehicle s tach signal will have to be learned before initial operation see below RPM Learn Start the engine enter Branch 21 and press Button 1 to learn the vehicle s tach signal The horn will chirp and the LED will flash once to confirm learning of the tach signal and entering Tach Monitor Mode The horn will chirp four times and the LED will flash four times if the tach signal was not learned engine sense mode will not be changed Gas Engine Sets the engine type for Gasoline Diesel Engine Sets the engine type for Diesel and mon itors the glow plug input to make sure the glow plugs are warm before cranking the starter If the glow plug wire is not connected the built in timer waits 15 seconds before automatically cranking the star
7. 500 mA Connect to an optional factory security bypass module if required Pin 3 BROWN WHITE Horn Output 500 mA Connect to a relay to activate the vehicle s horn when the alarm is triggered Pin 4 GRAY Auxiliary 1 Output 500 mA Connect to a relay for an optional feature such as trunk release etc This output may be programmed for momentary timed or latched operation Pin 5 WHITE BLACK Hood Pin Input Connect the to the hood pin switch The switch must provide a ground output when switch is opened Pin 6 GREEN WHITE Brake Input Connect to the wire that shows 12V when pressing the brake The Green white wire is a safety shutdown wire that must be connected Pin 7 BLACK GRAY Tach Input Connect to the vehicle s tach wire or a fuel injector wire if the tachless mode does not provide satisfactory operation Pin 8 ORANGE Programmable Starter Disable Output 500 mA The Orange wire provides a ground output while locked to disable the starter on the vehicle Factory Rearm Output 5 Pin White Connector Two Way Receiver Connector 3 Pin White Door Lock Connector Door lock port e BLUE WIRE negative unlock output 500mA eGREEN WIRE negative lock output 500mA Astra 300RS Page 7 SVS PROGR MIMMINE System Programming The system programming is compatible with both the LCD transmitter or the standard AM transmitter Enter System Programming 1 Turn on ignition 2 Within 5 seconds press the valet switch
8. alet Code Set This dual program branch selects Ignition Door Locking and programs the optional Emergency Valet Code Ignition Door Locking Selects whether or not the system will automatically lock the doors 5 seconds after the ignition key is turned on Valet Code Set Changes the Emergency Valet Code for a higher level of security 7 Ignition Door Unlocking Selects whether or not the system automatically unlocks the doors when the ignition is turned off 8 Door Unlock Pulse Selects between one pulse or two pulse operation for the door unlock output Many new import vehicles factory door locking systems require two pulses on the proper wire to unlock the doors These systems can be interfaced directly without the use of relays or any additional circuitry by programming the system for double un lock pulse also programs to pulse the ignition before unlock 9 Door Lock Pulse Length Selects between a 1 second 3 second or 0 1 second output for door locking and unlocking Program to 3 seconds for vehicles equipped with vacuum door locking systems 0 1 seconds for vehicles that roll windows up or down when lock unlock output is at 1 second Page 8 Astra 300RS SVS PROGR MIMMINE 12 Auxiliary 1 Mode Selects from momentary 10 second timed or latched operation for Auxiliary 1 Momentary eration provides an output for as long as the transmitter button is pressed Timed operation provides an output that turns on for 10 seconds each time t
9. cle is equipped with a factory theft deterrent system and obtain proper bypass module if required 5 Find a location to mount the hood pin switch that will not interfere with the opening of the hood and is not in a position that can accumulate water The hood pin is a safety device that must be installed to avoid remote starting during engine servicing 6 Verify with the owner the mounting locations for all visible components including the LED and Valet switch 7 Verify with the owner the optional features of the ASTRA 300RS and the features that must be programmed during installation 8 Inspect and perform a function test of all vehicle systems before and after the installation 9 Always use a Volt Ohm meter for testing vehicle circuits Never use a test light 10 Always look before drilling any holes or mounting self tapping screws Be sure fuel lines and exterior wiring looms are clear as they are often close to the chassis and difficult to see 11 Protect all wires running from the engine compartment to the interior of the vehicle by covering with electrical tape and split loom tubing Be sure to use a grommet when routing wires through the firewall 12 Properly fuse any additional accessories such as window modules door lock actuators etc making sure to power them separate from the alarm module This will ensure the functionality of the security system in the event of an accessory failure Mounting the Control Unit The contro
10. dure Before beginning this procedure be sure to have the ignition key ready and know the location of the valet switch To Emergency Valet the system 1 Unlock the door using the key 2 Enter the vehicle 3 Turn ignition key on 4 Press and hold the valete switch until LED turns off The system will deactivate the starter intrruptoutput 5 The vehicle will now be able to start Valet Mode The Valet Mode temporarily disables remote start system so the vehicle may be operated by a mechanic To activate or deactivate the Valet Mode 1 Turn on the ignition 2 Press and hold the valet switch for 5 seconds The horn will chirp once and the LED light will stay ON to confirm the Valet Mode is The horn will chirp twice and the LED light will turn OFF to confirm the Valet Mode is off 3 Turn off the ignition While in Valet Mode the remote transmitters will continue to lock and unlock the doors and operate the optional aux iliary functions Astra 300RS System Installation 1 Thoroughly read and become familiar with the installation instructions before beginning the installation 2 Review system contents Main Unit Two 4 Button Remote Transmitters Harnesses e 6 Wire starter harness e 3 Pin Power harness e 8 Pin main harness e 3 Pin door lock harness e LED Valet Switch and antenna Harness 3 Verify vehicle is equipped with electronic fuel injection and starts idles normally before installation 4 Determine if vehi
11. ergency the transmitter s remote Panic feature can be used to instantly trigger the Horn To activate the Panic Mode 1 Press and hold Button 1 for 3 seconds The horn will sound The parking lights will flash The doors will unlock allowing access to the vehicle 2 Press Button 2 to stop Panic Mode If the ignition is on when the Panic feature is activated the doors will lock for personal safety If not deactivated using Button 2 the Panic Mode will automatically exit after 30 seconds and the system will be restored to its previous Lock Unlock state Page 4 Astra 300RS System Operation 300865 Remote Starting To Remote Start the System 1 Be sure the system is not in Valet Mode 2 Press Button 1 on the remote for two seconds The parking lights will flash 4 times and turn on The Horn will chirp 4 times when starter confirmation chirps is enabled The engine will start and run for the duration of its programmed Run Time The heater or air conditioner will turn on if turned on prior to exiting the vehicle If the engine fails to start on the first attempt it will repeat the starting procedure 2 more times If the vehicle fails to start after a total of 3 times the parking lights will flash 4 times and the doors will lock if installed Turn on the ignition and press the brake pedal to disengage the remote start feature and drive the vehicle Remote Shut Down When the the Remote Start feature is acti
12. he transmitter button is pressed If the button is pressed again during the 30 seconds the output will turn off Latched operation provides an output that turns on when the transmitter button is pressed and remains on until the transmitter button is pressed again 13 Unlock with Auxiliary 1 When selected activating the Auxiliary 1 output Usually used to open the trunk will disarm the alarm 14 Starter Confirmation Chirps When Enabled horn will chirp to confirm Starter Active state Enable Auxiliary Start Activation Enable to use the axillary start feature if used in keless entry mode 15 Start in Valet Mode Selects whether or not the vehicle can remote start while in the valet mode 16 Lock After Start When selected the doors will automatically lock after remote starting 17 Lock After Shutdown When selected the doors will automatically lock after remote shutdown 18 Engine Run Time Selects between 15 or 25 minutes for the remote start run cycle 19 Automatic Start Mode Selects between every two hours or every hours for the automatic engine starting feature 20 Tachless Sense Crank Time Selecting engine crank time automatically selects the tachless mode and one of three crank times If the normal engine crank time is too short increase the time by selecting one of the two additional extended crank time options Normal 0 8Sec Extended 1 0Sec Super Extended 1 4Sec Tachless Mode Determines the engine status using an
13. ignition wire that provides 12V when the ignition is on and while cranking the starter Pin 6 VIOLET Starter Output Connect to the the vehicle s starter wire Note if connecting at the ignition switch it is highly recommended to use separate power wires for each Red wire each with a minimum 30A supply Remove the fuse until the installation is completed and all wiring is checked 3 Pin Power Harness Pin 1 RED WIRE Module Power Input Connect to a constant source of 12V Pin 2 WHITE Parking Light Output relay Connect the White wire to the circuit that shows 12V or ground only when the parking lights are on and set the internal parking light relay jumper to the proper polarity For park ing light circuits exceeding 10 amps a relay is required For vehicle s with independent left and right parking light circuits diodes must be installed to keep the circuits separate NOTE Do not connect the WHITE wire to the vehicle s headlight circuit Pin 3 BLACK Ground Input The Black wire must connect to a solid chassis ground Clean away any paint or dirt to insure the best possible ground 8 Pin Main Harness Pin 1 WHITE VIOLET Factory Disarm Output 500 mA The Violet white wire provides a ground output on dis arming and before remote starting to disarm a factory security system Connect to the wire that requires a ground pulse to disarm the factory security system Pin 2 BLUE ORANGE Ground When Running Output
14. l unit must only be mounted in the interior of the vehicle Do not mount the main unit in the engine com partment Choose a mounting location that will not be easily accessible to a thief and will not interfere with the op eration of any vehicle components such as foot pedals steering column air vents seat rails etc Do not mount the control unit until after setting the internal jumpers and performing a complete operation check of the system After installation is complete and performance verified the control unit can be easily mounted using wire ties through the mounting tabs on the bottom of the unit Page 6 Astra 300RS 6 Wire Starter Harness Pin 1 RED A Main Power Input A Connect to the battery or constant power wire at the ignition switch with a minimum 30 Amp supply Remove the fuse until the installation is complete and all wiring is checked Pin 2 RED B Main Power Input B Connect to the battery or constant power wire at the ignition switch with a minimum 30 Amp supply Pin 3 BROWN Second Ignition Output The Brown wire provides 12V for a second ignition wire This wire may instead be programmed for use as a second accessory or second starter wire Pin 4 ORANGE Accessory Output Connect to the accessory wire coming from the ignition switch that supplies power to the heater air conditioner Some cars may have multiple accessory wires Pin 5 YELLOW Ignition Output Connect to the main
15. ter 22 Ignition 2 Relay Program Selects one of three operating modes for the Ignition 2 relay output Ignition 2 Accessory 2 or Starter 2 26 Data Bus Input Trigger When enabled all available trigger from the Data Bus Module will be monitored door hood brake and all other triggers will not be nessecery to hard wire 27 Horn Chirp Duration Selects between Normal default Extended and super extended horn On time During chirping of the horn 28 Starter Disable Output Mode Select between Starter Disable output Factory Rearm output and Second Auxiliary output on the orange wire 29 Selects between Astra 1000RS and Astra 4000RS doesn t apply to Astra 300RS 30 When enabled doors unlock before start 31 Data Port Interface Mode Selects between iDatalink and Fortin module communications Astra 300RS Page 9 Brunch Feature Butoni Button 3 Silent Horn Chirps ON 2 2 gt gt O 5 Reset Mobilink 5 5 Double Pulse Ignition before Unlock Latched ff ff ff ff ff Door Lock Pulse Length 12 13 14 15 16 17 18 19 20 21 22 Timed Enabled Enabled O 25 Min 1 Hour Extended Super Extended Smart Start Monitor Disabled Data Bus RPM Gas Engine Diesel Engine Accessory 2 Output Starter 2 Output Pulsed Disabled Disabled Unlock with Aux 1 Starter Confirmation Chirps Lock Af
16. ter Start 5 15 Min 2 Hour Normal Smart Start RPM Mode RPM Learn __ a Automatic Start Interval foe S achless Sense Crank Time Super Extended Engine Sense Mode Remote Start Program Output Ignition 2 Program Ignition 2 Ouput NI N N aj AU 26 27 28 29 30 31 Enabled Normal Starter Disable Output Mode Starter Disable Output System Mode Astra 1000 4000 Astra 1000RS Disabled iDataLink Extended Super Extended Astra 4000RS Fortin Se ES EA EA ER ES EA EA ES ZS 91 EA pe ES Cc T mIo gt oS 5 Z Si Q a Q 8 3 9 527 m A gt gt gt ole lt 5 5 10 zA pa mi Dis gt S gt gt a Silo 5 gt 0 s rlololo gt gt gt oO oO 1 V x Vig ojo Sle Q amp Q gt 2 6 5 a a 2 a 10 Astra 30085 DOO 9 Negative Trigger Green wire LOCK Blue wire UNLOCK Door Lock wire FACTORY Door Unlock wire pein DOOR LOCK SWITCH Reverse Polarity L 15A FUSE UL DOOR LOCK 12V SWITCH Blue wire FACTORY UNLOCK MOTOR
17. ve any of the following actions will shutdown the engine 1 Pressing and releasing Button 1 within 1 second After the engine shuts down the doors will lock if installed 2 Pressing the Brake Pedal 3 Opening the Hood 4 Remote Start Time Out completion of the timed run cycle Remote Unlocking To unLock the doors 1 Press and hold button 1 on the remote for 3 seconds this feature works only when engine is running The doors will unlock The parking lights will flash twice Auxiliary Function Outputs The ASTRA 300RS are equipped with 1 Auxiliary Channel Output allowing the convenience features of the system to be further expanded This output can be programmed for pulsed timed or latched operation and used to add a number of optional features such as power trunk release power window activation power sunroof control auxiliary lighting audio video system control and more The Pulsed operation setting allows an output to activate as long as the button is held The Timed operation setting allows an output to activate when the transmitter button is pressed and remain activated for 10 seconds or until the transmitter button is pressed again The Latched operation setting allows an output to activate when the transmitter button is pressed and remain activated until the transmitter button is pressed again Emergency Valet Switch If the transmitter becomes lost or inoperable the Doors can still be unlocked using the following proce
Download Pdf Manuals
Related Search