Weed Eater XT 600 Operator`s manual
Contents
1. Engine flooded Fuel Tank empty Spark Plug not firing Fuel not reaching carburetor Carburetor requires adjustment Grass wrapped around Trimmer Head Air filter dirty Spark plug fouled Carburetor requires adjustment 5 Carbon build up on muffler outlet screen 6 Compression low 1 Fuel mixture incorrect 2 Air filter dirty 3 Carburetor requires adjustment 1 Fuel mixture incorrect 2 Spark Plug incorrect 3 Carburetor requires adjustment 4 Carbon build up on muffler outlet screen 1 Carburetor requires adjustment 2 Crankshaft seals worn 3 Compression low Technical Service apm You may have further questions about assembling operating or maintaining this Trimmer If so you can contact our Technical Service Department at 1 800 737 2112 English only You may also write to METL Corporate Office CORRESPONDENCE ONLY ATTN Technical Service METL 6700 Wildlife Way Long Grove IL 60047 1 Move ignition switch to the ON position 2 See Starting a Flooded Engine in OPERATION section 3 Fill tank with correct fuel mixture 4 Replace Spark Plug 5 Check for kinked or split fuel line repair or replace Contact a qualified service center Clear debris and grass from Trimmer Head Clean air filter Clean or replace plug Contact a qualified service center Contact a qualified service center Contact a qualified service center Empt2. Save all instructions Emission Warranty Parts List The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty coverage if METL demonstrates that the engine has been abused neglected or improperly maintained and that such abuse neglect or improper maintenance was the direct cause of the need for repair or replacement of the part That notwithstanding any adjustment of a component that has a factory installed and properly operating adjustment limiting device is still eligible for warranty coverage The following emissions warranty parts list is covered 1 Fuel Metering System 4 Catalytic Muffler Assembly if so equipped including a Gasoline carburetor assembly and its internal a Muffler gasket components if so equipped b Exhaust manifold b Fuel filter if so equipped 5 Crankcase Breather Assembly including c Carburetor gaskets Breath tion t d Fuel pump if so equipped a Breather connection tube PEPI 6 Miscellaneous items Used in Above Systems including 2 Air Induction System including a Switches a yeaa manifold b Hoses belts connectors and assemblies 3 Ignition System including a Spark plug b Ignition module coil When the engine is used at a region where the altitude is over 3000 foot a High Altitude Kit may be required to meet proper engine performance and emission control Contact the Toll Free service phone
3. describe the warranty procedures or policies within five working days of request by the Executive Officer Evaporative Emission Warranty Parts List 1 Fuel Tank Questions Call Toll Free at 1 800 737 2112 17 Copyright 2011 MAT Engine Technologies LLC
4. instructions This warranty is extended only to the original retail purchaser The bill of sales or proof of purchase must be presented at the time a claim is made under this warranty This warranty does not cover commercial industrial or rental usage nor does it apply to parts that are not in original condition because of normal wear and tear or parts that fail or become damaged as a result of misuse accident lack of proper maintenance tampering or alteration Travel handling transportation and incidental costs associated with warranty repairs are not reimbursable under this warranty and are the responsibility of the owner To the full extent allowed by the law of the jurisdiction that governs the sale of the product this express warranty excludes any and all other expressed warranties and limits the duration of any and all implied warranties including warranties of merchantability and fitness for a particular purpose to two years from the date of first purchase and MAT Engine Technologies LLC s liability is hereby limited to the purchase price of the product and MAT Engine Technologies LLC shall not be liable for any other damages whatsoever including indirect incidental or consequential damages Some states do not allow limitation of how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages so the above limitation of damages may not apply to you This warranty provides the original purchaser wit
5. number below for part replacement at the authorized service dealership Operating the engine with the wrong engine configuration at a given altitude may increase its emission and decrease fuel efficiency and performance Questions Call Toll Free at 1 800 737 2112 15 Copyright 2011 MAT Engine Technologies LLC Warranty Continued e Save all instructions California Evaporative Emission Control Warranty Statement YOUR WARRANTY RIGHTS AND OBLIGATIONS Applies only to Model No S HLT 2515 CB The California Air Resources Board and METL are pleased to explain the evaporative emission control system s warranty on your 2010 model year small off road engine SORE In California new SOREs must be designed built and equipped to meet the State s stringent anti smog standards METL must warrant the evaporative emission control system on your SOREs for the period of time listed below provided there has been no abuse neglect or improper maintenance of your SOREs Your evaporative emission control system may include parts such as carburetors fuel tanks fuel lines fuel caps valves canisters filters vapor hoses clamps connectors and other associated components Manufacturer s Warranty Coverage This evaporative emission control system is warranted for two years If any evaporative emission related part on your equipment is defective the part will be repaired or replaced by METL Owner s Warranty Responsi
6. spool see Fig 16 9 With your finger between the Trimmer lines of the loop wrap the lines keeping the lines taut with firm constant tension around the spool in a clockwise direction Make sure to keep each of the Trimmer lines on the proper side of the center divider on the spool see Fig 17 WIND LINE IN THIS DIRECTION 10 Confirm spool spring is secured in proper position on spool see Fig 18 11 While securing the Trimmer line around the spool insert spool into the Spool Housing and insert the end of each of the Trimmer lines into opposing eyelets in the Spool Housing Pull the Trimmer line through eyelets removing any slack in the line The Trimmer line should extend through each eyelet approximately 4 inches 102 mm 12 Assemble and secure the Bump Knob on the Trimmer shaft firmly To tighten the Bump Knob turn the knob clockwise see Fig 4b 13 After installing new Trimmer line start Trimmer engine and advance Trimmer line with Bump Knob until Trimmer line is trimmed at its full cutting width by the Trimmer line knife see E Advancing Trimmer Line E Ae Questions Call Toll Free at 1 800 737 2112 9 Copyright 2011 MAT Engine Technologies LLC Routine Maintenance e Save all instructions A WARNING Disconnect the spark plug before performing maintenance A Air Filter Accumulated debris and dust in the air filter will reduce engine performance increase fuel consumption and increases t
7. 2 Move the Ignition Switch to the ON position see Fig 7 3 Move the choke RUN WARM START position lever to 4 Squeeze and hold the throttle lever pull the Recoil Starter Handle sharply until the engine starts and runs Q a Warm Start PRIMER BULB j Copyright 2011 MAT Engine Technologies LLC Operation continued e Save all instructions B Starting Engine Starting A Flooded Engine 1 Place the Trimmer on a flat surface 4 Squeeze and hold the Throttle Lever fully depressed and pull the starter handle repeatedly until engine starts and runs This could require pulling the starter handle 3 Move the choke lever to RUN WARM START position many times depending on how badly the unit is flooded 5 Ifthe engine still does not start allow the unit to sit for about 30 minutes and repeat step 1 3 2 Move the Ignition Switch to the ON position If the unit still doesn t start refer to the T If you need assistance or have any questions TROUBLESHOOTING section of this manual or CALL TOLL FREE 1 800 737 2112 Stopping The Trimmer A CAUTION The Trimmer head and line will continue to rotate for a few seconds after the engine has stopped 1 Release the Throttle Lever and allow the engine to idle for a few moments 2 Move the Ignition Switch to the OFF position D Engine Break in Period During the first ten 10 hours of use use the slowest engine speed whi
8. HSOUTHLAND Operator s Manual CURVED SHAFT TRIMMER 25CC 2 Cycle MODEL NO s S HLT 2515 CB E S HLT 2515 CB Look inside for Page Safety Definitions 1 Important Safety Information 2 3 Product Specifications 4 Parts amp Features 4 Assembly 4 5 Operation 6 9 Routine Maintenance 10 Storage 10 Troubleshooting 11 Technical Service 11 Warranty 12 17 IMPORTANT Thank you for purchasing this Southland Trimmer This manual provides complete instructions for safely operating and maintaining your Trimmer Read and save these instructions Refer to this manual each time before using your Trimmer Record the following for future reference Mfg Date Code Date of Purchase Attach a copy of your sales receipt Consumer Toll Free Number 1 800 737 2112 Refer to the website for electronic manual and parts book www southlandpowerequipment com A WARNING This product contains one or more chemicals known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling T If you have a question or problem CALL TOLL FREE 1 800 737 2112 KEEP THIS MANUAL FOR FUTURE REFERENCE 11 23 2010 Printed in China A200129 Safety Definitions e Save all instructions Safety Warning Symbols Indicates Warning Keep all by standers at least 50 ft 15 m away Read these instructions carefully This equipment can throw small objects at high speed causing personal injury In
9. Remove fuel cap slowly Maintenance amp Storage of Trimmer A WARNING 1 Disconnect the spark plug before performing maintenance 2 Maintain Trimmer with care Inspect Trimmer periodically If Trimmer is not working properly or damaged have it repaired by a qualified service center 3 Check for misalignment of moving parts binding of moving parts broken parts mounting and any other condition that may affect its operation 4 Keep guards in place and in working order 5 A guard or other part that is damaged should be properly repaired or replaced by a qualified service center 6 Use only genuine Southland replacement parts and accessories Use of any non Southland parts or accessories could lead to injury damage to the unit and will void your warranty 7 Do not remove or modify any parts Removing or modifying parts could lead to injury damage the Trimmer and will void the warranty 8 Keep handles dry clean and free from oil and grease 9 Allow engine to cool and empty the fuel tank before storing or transporting in vehicle Use up remaining fuel in the carburetor by starting the engine and letting it run until it stops 10 When not in use store Trimmer indoors in a dry location Store Trimmer above the reach of children or in a locked area out of the reach of children 11 Store unit and fuel in area where fuel vapors cannot reach sparks or open flames from water heaters electric motors or switches furnaces et
10. Safety Information e Save all instructions Before Operating Trimmer READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE OPERATING TRIMMER A WARNING Read and follow all warnings and safety instructions Failure to do so can result in serious injury to you or bystanders 1 Avoid Dangerous Environments a Do not operate Trimmer while under the influence of alcohol medications or drugs b Do not operate Trimmer when you are tired c Do not use this Trimmer if you are mentally or physically unable to operate safely 2 Inspect Trimmer for damaged parts and make sure all fasteners and guards are in place and secure Replace any damaged parts 3 Use only 0 080 inch 2 mm diameter flexible nonmetallic line with this Trimmer This Trimmer is not designed for use with a rigid blade Never use this Trimmer with a rigid blade or other accessories not specifically approved for use in this manual Never use alternative cutting members such as wire or wire rope which can break off and become a dangerous projectile 4 Dress properly when operating Trimmer a Always wear heavy long pants boots gloves and a long sleeve shirt b Do not wear loose clothing or jewelry that can get caught in the moving parts of the Trimmer c Always wear gloves and substantial foot wear when working outside d Always wear protective hair covering to contain long hair Always wear a face or dust mask if operation is dusty Always wear eye protection that meets
11. Trimmer will cause your Trimmer to be less effective and will cause excessive wear on the Trimmer line To avoid damaging trees shrubs and fences 3 Use the slowest engine speed that will permit effective cutting This will provide the greatest control of the trimming line reduce engine noise and vibration and extend Trimmer line life 1 Maintain Trimmer line to the full cutting width by advancing trimmer line as necessary 2 Move the tips of the Trimmer line slowly into the grass or vegetation to be trimmed Use a sweeping motion from right to left see Fig 12a to Fig 12a move the Trimmer line into the grass or vegetation to be cut RIN i SAFE CUTTING z F IAE SWEEP RIGHT By using the trimming line on the left side and front of the Ea TO LEFT AoE Trimmer Guard debris will be thrown away from you see Fig 12b Trimming Fig 13 Holding the Trimmer Head approximately 3 inches 76 mm above the ground with the trimmer line angled down towards the grass or vegetation to be trimmed move the Trimmer Head in a sweeping motion from right to left into the grass or vegetation see Fig 13 N 3 76 mm Scalping Scalping is a technique similar to Trimming but clears all vegetation to the ground Holding the Trimmer Head approximately 3 inches 76 mm above the ground with the Trimmer line angled down towards the grass or vegetation to be trimmed Allow the Trimmer line to strike the ground where sc
12. alping is desired see Fig 14 Mowing The Trimmer is effective in mowing areas your lawn mower cannot easily reach Holding the Trimmer Head parallel to the ground move the Trimmer Head in sweeping motions from right to left Avoid the Trimmer Head contacting the ground this may scalp the grass and damage the unit Questions Call Toll Free at 1 800 737 2112 8 Copyright 2011 MAT Engine Technologies LLC Operation continued e Save all instructions G Replacing Trimmer Line A WARNING Use only 0 080 inch 2 mm diameter flexible nonmetallic line with this Trimmer Other line sizes will not function properly and can cause serious injury Never use alternative cutting members such as wire or wire rope which can break off and become a dangerous projectile 1 Stop the engine A WARNING Disconnect the Spark Plug before performing maintenance except for carburetor adjustments 2 Position the Trimmer on the ground so that the Trimmer Head Assembly is facing up Loosen and remove the Bump Knob see Fig 1 gt A Remove spool and spool spring from the Trimmer Head Assembly and clear any remaining Trimmer line from the spool 5 When replacing Trimmer line only use 0 080 in 2 mm diameter line D Cut a length of new Trimmer line 20 ft 6 m long Bend the line in the middle to form a loop of two equal lengths see Fig 15 8 Hook the bend of the loop onto one of the slots in the center of the
13. bilities e As the SORE owner you are responsible for performance of the required maintenance listed in your owner s manual METL recommends that you retain all receipts covering maintenance on your SOREs but METL can not deny warranty solely for the lack of receipts e As the SORE owner you should however be aware that METL may deny you warranty coverage if your SOREs or a part have failed due to abuse neglect or improper maintenance or unapproved modifications e You are responsible for presenting your SOREs to distribution center or service center authorized by METL as soon as the problem exists The warranty repairs should be completed in a reasonable amount of time not to exceed 30 days coverage you should contact METL customer service CALL TOLL FREE 1 800 737 2112 If you have any questions regarding your warranty T If you need assistance or have any questions Questions Call Toll Free at 1 800 737 2112 16 Copyright 2011 MAT Engine Technologies LLC Wa rra nty Continued e Save all instructions Defects Warranty Coverage a The warranty period begins on the date the engine is purchased b General Evaporative Emissions Warranty Coverage The engine must be warranted to the ultimate purchaser and any subsequent owner that the evaporative emission control system when installed was 1 Designed built and equipped so as to conform with all applicable regulations and 2 Free from defects in materials and wor
14. c Questions Call Toll Free at 1 800 737 2112 3 Copyright 2011 MAT Engine Technologies LLC Product Specifications e Save all instructions ENON soseri aae eee e hee A S 25 cc 2 cycle 2 Cycle Oil Type 2 Cycle Oil that meets or exceeds Speed oor aare aa ee a N ee 7 000 8 500 RPM o aoaoaonnnnnnnnnaannaaannnnnn JASO FC Specifications Cutting Diameter 15 in 881 mm Fuel Mixture 40 1 Gasoline 2 Cycle Oil Line DIGMGIE c 0ceecesscee esha aa 0 080 in 2 mm Spark Plug nonan anaana NGK BPMR7A Spool Type 2 deed oda sa dere ds Bump Feed Twin Line 0c cece ee eee CHAMPION CJ7Y Fuel Tank Capacity 05 20 oz 600 IM o6 cea idan avant Heden oe nee oh awe andes or equivalent Fuel Type Unleaded Gasoline 87 Octane or higher Net Weight 2 00005 11 7 Ibs 5 3 kg Parts amp Features Trimmer Head Assembly On Off Ignition Switch Fuel Tank Bump Knob es Recoil Starter Handle Air Filter Cover Trimmer Line Knife Fuel Primer Bulb 16 Spool Housing Front Handle Spark Plug Assembly O you need assistance or find any parts missing CALL TOLL FREE 1 800 737 2112 Parts Included With The Packaged Trimmer Front Handle with Bolt and Nut e 40 1 2 Cycle Engine Oil 3 2 fl oz Trimmer Guard with Bolt and Wing Nut e Operator s Manual Spark Plug Wrench A WARNING Do not operate Trimmer if it is damaged or not secure
15. ch allows for effective cutting and avoid operation at high engine speeds for extended periods of time This will maximize the life and performance of your Trimmer s engine Maximum power will be achieved after the first ten 10 hours of engine operation E Advancing Trimmer Line The Trimmer is most effective when the Trimmer line is advanced to full cutting width To advance the Trimmer line 1 Hold bottom of Trimmer Head parallel to grassy surface see Figure 11 I l fl LALALALALALA 2 With the engine at full throttle firmly tap or bump the Trimmer Head on the ground Trimmer line will be advanced with each tap or bump inl AANA Continue to advance Trimmer line until you reach full cutting width i e when the Trimmer line is cut by the Trimmer Line Knife I UE LEEN l Biag bi il al 1 Questions Call Toll Free at 1 800 737 2112 74 Copyright 2011 MAT Engine Technologies LLC Operation Continued e Save all instructions A WARNING Thoroughly inspect the area where the Trimmer is to be used and remove all foreign objects Your equipment can throw small objects at high speed causing personal injury or property damage Your Trimmer is most effective when using the tips of the Trimmer line for trimming grass and other vegetation Do not force the Trimmer line into grass or vegetation faster than Trimmer s cutting speed permits Forcing the
16. exclusions as stated below the warranty on emissions related parts is as follows 1 Any warranted part that is not scheduled for replacement as required maintenance in your Operator s Manual is warranted for the warranty period stated above If the part fails during the period of warranty coverage the part will be repaired or replaced by METL according to Subsection 4 below Any such part repaired or replaced under warranty will be warranted for the remainder of the period 2 Any warranted part that is scheduled only for regular inspection in your Operator s Manual is warranted for the warranty period stated above Any such part repaired or replaced under warranty will be warranted for the remaining warranty period 3 Any warranted part that is scheduled for replacement as required maintenance in your Operator s Manual is warranted for the period of time before the first scheduled replacement date for that part If the part fails before the first scheduled replacement the part will be repaired or replaced by METL according to Subsection 4 below Any such part repaired or replaced under warranty will be warranted for the remainder of the period prior to the first scheduled replacement point for the part 4 Repair or replacement of any warranted part under the warranty provisions herein must be performed at a warranty station at no charge to the owner 5 Notwithstanding the provisions herein warranty services or repair will be p
17. h specific rights For information regarding those rights please consult the applicable state laws METL Corporate Office CORRESPONDENCE ONLY ATTN Technical Service METL 6700 Wildlife Way Long Grove IL 60047 B Federal and California Emissions Control Warranty Statement This MAT Engine Technologies LLC METL outdoor power equipment engine complies with the emissions regulations of Southland Model No Regulatory Agency S HLT 2515 CB E United States Environmental Protection Agency U S EPA S HLT 2515 CB State of California To the extent there is any conflict between this Emissions Control Warranty and the METL Limited Warranty this Emissions Control Warranty shall apply except where the METL Limited Warranty may provide a longer warranty period Please read your warranty rights and obligations carefully Some sections of the warranty may not apply to the specific model you purchased Unless specifically noted otherwise the terms below shall apply to all Southland products covered within this manual YOUR WARRANTY RIGHTS AND OBLIGATIONS State of California Applies only to Model No S HLT 2515 CB The California Air Resources Board and MAT Engine Technologies LLC METL are pleased to explain the emissions control system warranty on your 2010 small off road engine SORE In California new SOREs must be designed built and equipped to meet the State s stringent anti smog standards METL mu
18. he risk of engine damage Clean the air filter every 5 hours of operation 1 Before removing Air Filter Cover brush away any loose yn WARNING dirt or debris on and around the filter cover 2 To remove Air Filter Cover press on the side tab and Never clean filter in gasoline or other flammable solvents pull cover out see Fig 19 4 Add a drop of thin oil to the filter and replace it 3 Remove and clean foam filter e Light surface dust can readily be removed by tapping the filter Heavy deposits should be washed out in soap and water Squeeze out any remaining water and allow the filter to completely dry B Spark Plug Inspect the spark plug after every 10 15 hours of use adjust spark plug gap and replace spark plug as necessary Replace spark plug every year to maintain engine performance and easy starting To inspect or replace the Spark Plug 4 Replace any worn plug with a recommended replacement see PRODUCT SPECIFICATIONS Clean and adjust the spark plug gap to 0 024 0 028 in 0 6 0 7mm Install the Spark Plug finger tight in the cylinder head then tighten firmly with the spark plug wrench 1 Remove the insulated spark plug boot 2 Use the spark plug wrench to remove the Spark Plug by turning counter clockwise 9 Clean and adjust the spark plug gap to 0 024 0 028 in 0 6 0 7mm 6 Replace the insulated spark plug boot Storage See 1 Allow engine to cool and empty the f
19. kmanship that causes the failure of a warranted part for a period of two years c The warranty on evaporative emissions related parts will be interpreted as follows 1 Any warranted part that is not scheduled for replacement as required maintenance in the written instructions must be warranted for the warranty period defined in subsection b 2 If any such part fails during the period of warrantycoverage it must be repaired or replaced by METL issuing the warranty Any such part repaired or replaced under the warranty must be warranted for a time not less than the remaining warranty period 2 Any warranted part that is scheduled only for regular inspection in the written instructions must be warranted for the warranty period defined in subsection b 2 A statement in such written instructions to the effect of repair or replace as necessary will not reduce the period of warranty coverage Any such part repaired or replaced under warranty must be warranted for a time not less than the remaining warranty period 3 Any warranted part that is scheduled for replacement as required maintenance in the written instructions must be warranted for the period of time prior to the first scheduled replacement point for that part If the part fails prior to the first scheduled replacement the part must be repaired or replaced by METL Any such part repaired or replaced under warranty must be warranted for a time not less than the remainder of the
20. l for your immediate needs Do not store pre mixed fuel Stop engine and allow to cool before refueling To fill the trimmer s fuel tank with the gasoline oil mixture place the Trimmer upright on the ground or ona sturdy bench and wipe and any debris from around the fuel cap 9 Remove fuel cap slowly and use a funnel to pour the mixture into the tank and replace the fuel cap 10 Avoid spilling fuel or oil Wipe up all fuel spills 11 Move at least 10 feet 3 meters away from fueling site before starting engine B Starting Engine A WARNING Keep all parts of your body away from cutting area the rotating trimmer lines and hot surfaces Cold Starting The Engine DO NOT squeeze the throttle lever until engine starts and runs 1 Place the Trimmer on a flat surface Move the Ignition Switch to the ON position see Fig 7 3 Move the Choke Lever upwards to the COLD START position see Fig 8 4 Press the Primer Bulb slowly 6 times see Fig 9 Pull the Recoil Starter Handle sharply until the engine starts and runs see Fig 10 6 After engine starts and runs for 10 15 seconds move choke lever to RUN WARM START position Questions Call Toll Free at 1 800 737 2112 Note when the weather gets cold please allow the engine to warm up at idle for longer period of time before engaging to RUN WARM START position Warm Starting The Engine 1 Place the Trimmer on a flat surface
21. ly and fully assembled Tools Needed For Assembly 10 mm wrench or adjustable wrench Questions Call Toll Free at 1 800 737 2112 4 Copyright 2011 MAT Engine Technologies LLC Assembly Continued e Save all instructions A To Assemble Trimmer Guard 1 The Trimmer Head Assembly must be removed to enable the Trimmer Guard to be assembled To remove the Trimmer Head Assembly a Remove the bump knob from the trimmer head by turning the knob counter clockwise see Fig 1 b Remove trimmer line spool and Spool Housing see Fig 2 2 Disassemble the nut washer and bolt from the Trimmer Guard as received in the trimmer package 3 Assemble Trimmer Guard over the end of shaft and align holes in Trimmer Guard with guard bracket on shaft see Fig 3 4 Assemble bolt washer and nut through Trimmer Guard and guard bracket Tighten nut securely see Figs 4a 4b by using 10mm wrench 5 Assemble the Trimmer Head Assembly by tightening the bump knob clockwise see Fig 4b 6 Remove protective cover from trimmer line knife The Trimmer Line Knife is sharp and can cut you see Fig 5 B To Adjust Front Handle The Front Handle on your Trimmer is adjustable for your comfort and requires adjustment from its shipping orientation before your first use of the Trimmer To adjust the Front Handle 1 Loosen wing nut on the Front Handle 2 Adjust Front Handle to desired position and re tighten wingnut
22. n not deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance e As the SORE owner you should however be aware that METL may deny your warranty coverage if your SORE or a part has failed due to abuse neglect improper maintenance or unapproved modifications e You are responsible for presenting your SORE to a distribution center or service center authorized by METL as soon as the problem exists The warranty repairs should be completed in a reasonable amount of time not to exceed 30 days If you need assistance or have any questions coverage you should contact METL customer service CALL TOLL FREE 1 800 737 2112 If you have any questions regarding your warranty O Questions Call Toll Free at 1 800 737 2112 13 Copyright 2011 MAT Engine Technologies LLC Wa rra nty Continued e Save all instructions Defects Warranty Coverage METL warrants to the original purchaser and each subsequent purchaser that the small off road engine SORE 1 has been designed built and equipped so as to conform with all applicable regulations and 2 is free from defects in materials and workmanship that cause the failure of a warranted part to conform with those regulations as may be applicable to the terms and conditions stated below a The warranty period begins on the date the engine is first purchased The warranty period is two years b Subject to certain conditions and
23. or exceeds the requirements of ANSI Z87 1 Always wear hearing protection which meets or exceeds ANSI standards SoS Se O Thoroughly inspect the area where the Trimmer is to be used and remove all foreign objects A WARNING Your equipment can throw small objects at high speed causing personal injury or property damage While Operating Trimmer Stay alert Use common sense Watch what you are doing Do not operate Trimmer if it is damaged or not securely and fully assembled Only well instructed adults should operate Trimmer Never allow children to operate Trimmer Keep children away Keep all bystanders at least 50 ft 15 m away a O N eS This Trimmer is only intended for trimming scalping and mowing Do not use Trimmer for any job except that for which it is intended Do not use for edging pruning or hedge trimming 6 The Trimmer line may be spinning during carburetor adjustments Make carburetor adjustments with lower end supported to prevent Trimmer line from contacting any object Maintain your balance and proper footing at all times Do not overreach Keep rotating trimmer head below waist level Keep all parts of your body away from cuiting area the rotating trimmer lines and hot surfaces 9 Hold the unit firmly with both hands 10 Always keep engine on the right hand side of your body Questions Call Toll Free at 1 800 737 2112 2 Copyright 2011 MAT Engine Technologies LLC Important Safety Information con
24. period prior to the first scheduled replacement point for the part 4 Repair or replacement of any warranted part under the warranty provisions of this article must be performed at no charge to the owner at a warranty station 5 Notwithstanding the provisions of subsection 4 above warranty services or repairs must be provided at distribution centers that are franchised to service the subject engines or equipment 6 The owner must not be charged for diagnostic labor that leads to the determination that a warranted part is in fact defective provided that such diagnostic work is performed at a warranty station 7 Throughout the evaporative emission control system s warranty period set out in subsection b 2 METL issuing the warranty must maintain a supply of warranted parts sufficient to meet the expected demand for such parts 8 Manufacturer approved replacement parts must be used in the performance of any warranty maintenance or repairs and must be provided without charge to the owner Such use will not reduce the warranty obligations of the manufacturer issuing the warranty 9 The use of any add on or modified parts will be grounds for disallowing a warranty claim made in accordance with this article The manufacturer issuing the warranty will not be liable under this Article to warrant failures of warranted parts caused by the use of an add on or modified part 10 METL issuing the warranty shall provide any documents that
25. rovided at all of our distribution centers that are franchised to service the subject engines 6 The engine owner must not be charged for diagnostic labor that leads to the determination that a warranted part is in fact defective provided that such diagnostic work is performed at a warranty station 7 METL is liable for damages to other engine components proximately caused by a failure under warranty of any warranted part 8 Throughout the engine warranty period stated above METL will maintain a supply of warranted parts sufficient to meet the expected demand for such parts 9 Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge to the owner Such use will not reduce the warranty obligations of METL 10 Add on or modified parts that are not exempted by the Air Resources Board may not be used The use of any non exempted add on or modified parts by the original or subsequent purchaser will be grounds for disallowing a warranty claims METL will not be liable to warrant failures of warranted parts caused by the use of a non exempted add on or modified part 11 The manufacturer issuing the warranty shall provide any documents that describe that warranty procedures or policies within five working days or requested by the Air Resources Board Questions Call Toll Free at 1 800 737 2112 14 Copyright 2011 MAT Engine Technologies LLC Warranty Continued e
26. spect area where used and remove all foreign objects Always wear eye protection that meets or Keep all parts of your body away from exceeds the requirements of ANSI Z87 1 the rotating trimmer lines Wear hearing protection Wear breathing protection Wear safety footwear Explosive material Wear safety gloves Extremely hot surface Do not touch a hot muffler gear box or cylinder you may get burned These parts get extremely hot from operation and remain hot for a short time after the unit is turned off Do not use rigid blades Control and Operating Symbols Choke Control Fuel Mixture Fuel Mixture Cold Start 40 1 40 a 1 Run Warm Start Mix with More Than 10 Unleaded Gas 2 Cycle Oil Methanol or Ethanol Fuel Primer Ignition Switch Press Press 6 times ON a x6 primer 6 times OFF The information listed below should be read and understood by the operator We utilize the symbols below to allow the reader to recognize important information about their safety Indicates an imminently hazardous situation which if not avoided will result in death or serious injury Indicates a potentially hazardous situation which if not avoided could result in death or serious injury Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury Questions Call Toll Free at 1 800 737 2112 1 Copyright 2011 MAT Engine Technologies LLC Important
27. st warrant the emissions control system on your SOREs for the periods of time listed below provided there has been no abuse neglect or improper maintenance of your SOREs Questions Call Toll Free at 1 800 737 2112 12 Copyright 2011 MAT Engine Technologies LLC Wa rra nty Continued e Save all instructions Other U S States Territories In other areas of the Unites States your outdoor power equipment engine must be designed built and equipped so as to conform at the time of sale to U S EPA emissions standards for small off road spark ignition engines at or below 19 kilowatts All of the United States Your emission control system may include parts such as the carburetor or fuel injection system fuel lines the ignition system and catalytic converter Also included may be hoses belts clamps connectors and other emission related assemblies Where a warrantable condition exists METL will repair your small off road engine at no cost to you including diagnosis parts and labor Manufacturer s Warranty Coverage The emissions control system is warranted for two years If any emissions related part on your engine is defective the part will be repaired or replaced by METL Owner s Warranty Responsibilities e As the SORE owner you are responsible for the performance of the required maintenance listed in your owner s manual METL recommends that you retain all receipts covering maintenance on your SORE but METL ca
28. tinued e Save all instructions While Operating Trimmer 11 Always use the Trimmer in a sweeping motion from your right to your left Cutting on left side and front of the trimmer guard will throw debris away from you 12 Do not force Trimmer It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed 13 Never start or run the unit inside a closed room or building breathing exhaust fumes can kill 14 After turning the Trimmer off make sure the Trimmer line has stopped before the unit is set down Prolonged exposure to vibrations through use of gasoline powered hand tools could cause blood vessel or nerve damage in fingers hands and joints of people prone to circulation disorders or abnormal swellings Extensive use in cold weather has been linked to blood vessel damage in otherwise healthy people If symptoms occur such as numbness pain loss of strength change in skin color or texture or loss of feeling in the fingers hands or joints discontinue the use of this tool and seek medical attention Fuel Safety Mix and pour fuel outdoors WHERE THERE ARE NO SPARKS OR FLAMES Use a container approved for gasoline Do not smoke or allow smoking near fuel or the Trimmer 1 2 3 4 Avoid spilling fuel or oil Wipe up all fuel spills 5 Move at least 10 feet 3 meters away from fueling site before starting engine 6 Stop engine and allow to cool before removing fuel cap
29. uel tank before storingor 4 When preparing the Trimmer for storage or when transporting in vehicle Use up remaining fuel in the carburetor Trimmer will not be used for 30 days or more by starting the engine and letting it run until it stops a Inspect and clean the Trimmer thoroughly b Lightly oil all external metal surfaces c Remove the spark plug place a few drops of 2 cycle engine oil into the cylinder Pull the recoil starter several times to distribute the oil Replace 3 Store unit and fuel in area where fuel vapors cannot the spark plug reach sparks or open flames from water heaters electric d Inspect and clean air filter as required motors or switches furnaces etc 2 When not in use store Trimmer indoors in a dry location Store Trimmer above the reach of children or in a locked area out of the reach of children NOTE To prevent fuel gum deposits in the Trimmers carburetor and fuel system it is acceptable to use fuel stabilizer Follow the stabilizer manufacturer s instructions Run the engine at least 5 minutes after adding stabilizer Questions Call Toll Free at 1 800 737 2112 10 Copyright 2011 MAT Engine Technologies LLC Troubleshooting e Save all instructions PROBLEM POSSIBLE CAUSE S SOLLUTION S Engine will not start Engine will not accelerate lacks power or stalls Engine smokes excessively Engine runs hot Engine will not idle properly Ignition Switch in the OFF position
30. until the handle is secure see Fig 6 Questions Call Toll Free at 1 800 737 2112 5 Copyright 2011 MAT Engine Technologies LLC Operation e Save all instructions A Before Starting Engine Mixing Fuel 2 Cycle Oil A WARNING Do not smoke or allow smoking near fuel or the Trimmer Mix and pour fuel outdoors WHERE THERE ARE NO SPARKS OR FLAMES The 2 cycle engine on your Trimmer requires that fuel and 2 cycle engine oil be pre mixed before adding to the trimmer s fuel tank To mix the fuel 2 cycle oil 1 Use fresh unleaded gasoline with an octane rating of 87 or higher Do not use gasoline containing ethanol or methanol A CAUTION Use of gasoline containing ethanol or methanol can damage Trimmer 2 Always use 2 cycle oil that meets or exceeds JASO FC specifications and is intended for mixing at a fuel oil ratio of 40 1 3 Do not use automotive or 2 cycle marine outboard oil These will damage your trimmer s engine and void the warranty 4 Always mix the gasoline and 2 cycle oil in a container approved for gasoline Never mix fuel directly in the trimmer s fuel tank 5 Follow instructions on 2 cycle oil container for mixing fuel Mix gasoline and 2 cycle oil at a ratio of 40 1 A mixture with a 40 1 ratio is obtained by mixing 1 gallon 4 liters of gasoline with 3 2 ounces of oil 95 ml After adding oil to gasoline shake container momentarily to ensure proper mixing 6 Mix only enough fue
31. y Fuel Tank and refill with correct fuel mixture 2 Clean or replace air filter 3 Contact a qualified service center 1 See Mixing Fuel 2 Cycle Oil in OPERATION section 2 Replace with correct Spark Plug 3 Contact a qualified service center 4 Contact a qualified service center 1 Contact a qualified service center 2 Contact a qualified service center 3 Contact a qualified service center T If you need assistance or have any questions CALL TOLL FREE 1 800 737 2112 When contacting the Technical Service Department have ready e Your Name e Your Address e Your Phone Number e Model Number of Product e Date of Purchase include copy of receipt for written requests Questions Call Toll Free at 1 800 737 2112 11 Copyright 2011 MAT Engine Technologies LLC Warranty e Save all instructions CY Southtand TRIMMER Limited Warranty Always specify model number when contacting the factory We reserve the right to amend these specifications at any time without notice The only warranty applicable is our standard written warranty We make no other warranty expressed or implied MAT Engine Technologies LLC warrants this Trimmer and any parts thereof to be free from defects in material and workmanship for one year 90 days for reconditioned unit from the date of first purchase from an authorized dealer provided that the product has been properly maintained and operated in accordance with all applicable
Download Pdf Manuals
Related Search