Antunes, AJ Roundup CCC-20 Specifications
Contents
1. Antunes amp Co 9 0 0 1 ER TIF IE OD I 1 1 x 180 Kehoe Blvd Carol Stream Illinois 60188 USA 1 877 392 7854 Tech Service Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 CCC 20 TRAINING Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 CCC 20 SECTION PAGE eWarranty 4 eSpecifications 5 CCC warnings 7 CCC installation 10 CCC operating instructions 12 eTechnical theory of operation 13 eComponent description amp functions 14 eWiring diagram 16 eTools required 17 CCC maintenance 18 eTroubleshooting 19 eParts testing amp replacement 20 Ap Antunes amp Co oo 1060005 5 05 WARRANTY Equipment manufactured by Roundup Food Equipment Division of A J Antunes amp Co has been constructed of the finest materials available and manufactured to high quality standards These units are warranted to be free from mechanical and electrical detects for a period of one year from date of purchase under normal use and service and when installed in accordance with manufacturers recommendations To insure continued proper operation of the units follow the maintenance procedure outlined in the Owner Manual 1 This warranty does not cover cost of installation defects caused by improper storage or handling prior to placing of the Equipment This warranty does not include overtime charges or work done by unauthorized service ag2. HOC A Toa LIGHT GRH BLE TERHIN AL BLOCK 25 1 a SEE 2 VINDICATOR LIGHT WHT HEATER SWITCH POWER SWITCH Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 TOOLS REQUIRED FOR REPAIR amp TROUBLESHOOTING VOM Volt Ohm Meter digital or analog Clamp type amp meter digital or analog Flat blade screwdriver 14 Adjustable wrench 6 Nut driver set Channel locks Wire cutter crimper stripper Needle nose pliers Temp meter with submersible probe Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 MAINTENANCE Cleaning Daily Turn the unit off disconnect the power source 1 and allow the unit to cool down before performing any service or maintenance on the unit 2 Empty the Pan of used water Wash the Baskets and Pan in hot detergent water Rinse in clear water and dry sive cleaners on the unit 3 Wipe the Head Assembly with a damp cloth then dry with a clean dry cloth 4 Install the Head Assembly onto the pan Make sure the Safety Interlock Switch is engaged Remove Baskets and the Head Assembly 5 Install the Baskets Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 TROUBLESHOOTING To avoid possible personal injury and or damage to the unit inspection test and repair of electrical equip ment
3. ELECTRICAL SHOCK HAZARD FAILURE TO FOLLOW THE INSTRUCTIONS IN THIS MANUAL COULD RESULT IN SERIOUS INJURY OR DEATH Electrical ground is required on this appliance Do not modify the power supply cord plug If it does not fit the outlet have a proper outlet installed by a qualified electrician Do not use an extension cord with this appliance The unit should be grounded according to local electrical codes to prevent the possibility of electri cal shock It requires a grounded receptacle with separate electrical lines protected by fuses or cir cuit breaker of the proper rating Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded CCC 20 TECHNICAL MANUAL LAST UPDATE 5 1 05 1060005 5 05 OPERATION Operating Instructions 1 Fill the Pan about half full of hot tap water 2 Turn the Rocker Switch power On Off ON NOTE If the light on the Rocker Switch does not light up you must remove and reinstall the Head Assembly onto the pan Figure 1 to ensure that the Safety Interlock Switch is properly engaged If the Safety Interlock Switch is not engaged the Rocker Switch light will not turn on therefore the unit will not heat 3 Load each basket with a full or partial load of corn and immerse the baskets in the pan Water should completely cover corn Add more hot water if required 4 Allow corn to cook approximately 35 45 minutes The corn is ready to
4. 20 TECHNICAL THEORY OF OPERATION When the unit is plugged into the outlet line voltage flows to the normally open N O safety interlock switch Once its contacts close line voltage then flows to the input side of the power switch When the power switch is turned on line voltage then flows to a normally closed N C capillary bulb style thermostat Providing the water temperature within the pan is below 162 F 72 C the thermostat calls for heat by supplying line voltage to the heating element As the water begins to heat up the thermostat s bulb monitors the water temperature When the water temperature approaches approximately 162 F 72 C the thermostat s contacts open up amp turn off the heating element Simultaneously the Green indicator light will light up to indicate the water is up to temperature The heating circuit will cycle on amp off as needed even at idle If the heating circuit continues to call for heat the water will begin to boil amp overcook the corn NOTE If this condition should arise the root cause must be determined amp corrected Safety Interlock Switch Used to prevent operation of the heating element in the event the head assembly is not properly seated onto the pan or is being operated without the pan The switch has an actuating plunger which protrudes from beneath the head assembly Provided the head assembly is properly seated onto the pan the weight of the head assembly
5. 60005 5 05 Component Description amp Function Thermostat A normally closed N C capillary bulb style thermostat The bulb monitors the water temperature It will cycle the heating element 8 off as needed to maintain water temperature at approximately 162 F 72 C Green Light Used on all CCC 20 s except CCC 20 with Mfg 9600214 It is a line voltage indicator light that is located on the head assembly It is wired in parallel to the thermostat When lit it indicates the thermostat contacts are open amp the water temperature should be approximately 162 F 72 C When not lit it indicates the thermostat contacts are closed amp calling for heat Amber Light Used ONLY on the CCC 20 with Mfg 9600214 It is a line voltage indicator light that is located on the head assembly It is wired in parallel to the heating element When lit it indicates the thermostat contacts are closed amp calling for heat When not lit it indicates the thermostat contacts are open amp the water temperature should be approximately 162 72 C Pan The main container that accommodates the water corn baskets amp the head assembly Baskets Wire rack type baskets that accommodate the corn Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 WIRING DIAGRAM CORD WIRING DIAGRAM NOTES 1 ALL WIRES 14 105 UNLESS OTHERWISE SPECIFIED 18 AWM 2 FOR 1960014 ONLY
6. EACH OF WHICH IS HEREBY EXPRESSLY DISCLAIMED THE REMEDIES DESCRIBED ABOVE ARE EXCLUSIVE AND IN NO EVENT SHALL ROUNDUP BE LIABLE FOR SPECIAL CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR THE BREACH OR DELAY IN PERFORMANCE OF THIS WARRANTY Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 SPECIFICATIONS A ELECTRICAL SHOCK HAZARD A Electrical ground is required on this appliance Do Not modify the power supply cord plug If it does not fit the outlet have a proper outlet installed by a qualified electrician Do Not have a fuse in the neutral or grounding circuit A fuse in the neutral or grounding circuit could result in an electrical shock ELECTRICAL 1750 Watts 15 Amps Do Not use an extension cord with this appliance 120 VAC 60 Hz 6 ft 183 cm power cord and NEMA 5 15P plug e Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded Failure to follow these instructions could 220 240 1750 2090 Watts result in serious injury or death 8 0 8 7 Amps 220 240 VAC 50 60 Hz The CCC 20 Corn Cooker is completely wired 6 ft 183 cm power cord and and ready to plug When locating the Corn CEE 7 7 plug Cooker make sure that the Head Housing Assembly is to the rear away from front of counter of Base Housing Assembly This is nec COOKING TIME 35 to 45 minutes 160 F 71 C essary to insure proper operation of hea
7. HNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 TESTING TERMINAL BLOCK See Terminal Block under Component Description amp Function before proceeding Verify continuity across each of the three poles Replace if it fails test or if damaged Replacement Procedures Remove service panel Remove the two mounting screws amp nuts Disconnect terminal block wires Mark for reinstallation Reinstall wires onto new terminal block amp secure with screws amp nuts Test unit for proper operation Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 TESTING HEATING ELEMENT See Heating Element under Component Description amp Function before proceeding Replacement Procedures Remove service panel Disconnect element wires Remove clamps amp capillary bulb tubing from old element Remove the two element lock nuts amp remove element Install new element amp secure with lock nuts Reinstall the clamps amp capillary tubing onto new element Reinstall element wires Test unit for proper operation AR CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 TESTING THERMOSTAT See Thermostat under Component Description amp Function before proceeding To test thermostat for continuity Disconnect thermostat wires to isolate Verify continuity across terminals Replace if fails test To determine if an over heating con
8. NJURY OR DEATH Electrical ground is required on this appliance Do not modify the power supply cord plug If it does not fit the outlet have a proper outlet installed by a qualified electrician Do not use an extension cord with this appliance Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded This equipment is to be installed to comply with the local plumbing codes and any other applicable codes Do not clean this appliance with a water jet Do not use a sanitizing solution or abrasive materials The use of these may cause damage to the stainless steel finish Chlorides or phosphates in cleansing agents bleach sanitizers degreasers or detergents could cause permanent damage to stainless steel equipment The damage is usually in the form of discoloration dulling of metal surface finish pits voids holes or cracks This damage is permanent and not covered by warranty The following tips are recommended for maintenance of your stainless steel equipment Always use soft damp cloth for cleaning rinse with clear water and wipe dry When required always rub in direction of metal polish lines Routine cleaning should be done daily using soap ammonia detergent and water Stains and spots should be sponged using a vinegar solution as required Finger marks and smears should be rubbed off using soap and water Hard water spots should be sponged using a vinegar so
9. allows the plunger to become depressed therefore closing its contacts Thermostat The thermostat is fixed to maintain approximately 162 72 water temperature Heating Element The element must only be operated while submersed in water 20 Mfg 9600214 uses an Amber colored indicator light It lights up when the heating element is on It turns off when the heating element is off When off it indicates the water is up to temperature Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 CCC 20 Component Description amp Function Head Assembly It is the main assembly which consists of the following electrical components heating element power cord power switch thermostat safety interlock switch terminal block amp indicator light NOTE The heating element will not operate if the head assembly is not properly seated onto the pan or is being operated without the pan Power Switch Double Pole Single Throw turns the voltage On or Off to the unit s internal components NOTE The built in led illuminates when line voltage is present into amp out of the switch If not lit it normally indicates that the safety interlock switch is not be depressed The head assembly should be removed amp reinstalled onto the pan Splash Guard A clear PVC boot that fits over the face of the power switch It is used to help prevent water moisture from entering amp damaging the powe
10. dition is caused by a faulty thermostat Fill the pan with hot water about 1 2 5 cm above the thermostat bulb Turn unit on amp monitor the water temperature for at least 30 minutes Does the water temperature exceed 180 F 82 C If yes replace thermostat To determine if an under heating condition is caused by a faulty thermostat Fill the pan with hot water about 1 2 5 cm above the thermostat bulb Turn unit on amp monitor the water temperature for at least 30 minutes Does the water temperature reach at least 150 F 65 C If no replace thermostat Replacement Procedures Remove side service panel Remove thermostat mounting screws amp acorn nuts Disconnect thermostat wires Reinstall wires onto new thermostat Install amp secure new thermostat with screws amp acorn nuts NOTE Cautiously handle the bulb amp capillary tubing Failure to do so will result in premature thermostat failure Test unit for proper operation Af CCC 20 TECHNICAL MANUAL A J Antunes amp LAST UPDATE 5 1 05 1060005 5 05 TESTING GREEN OR AMBER INDICATOR LIGHTS See Green amp Amber lights under Component Description amp Function before proceeding Does the light turn on If no is there line voltage present across the indicator light If yes replace light Replacement Procedures Remove service panel Disconnect the indicator light wires Push the light up amp away from t
11. encies or personnel This warranty does not cover normal maintenance calibration or regular adjustments as specified in operating instructions or manuals see Owner s Manual of specific product and or labor involved in moving adjacent objects to gain access to the Equipment This warranty does not cover consumable items such as grill covers gaskets O rings and bulbs This warranty does not pay travel mileage or any other charges for a service to reach the equipments location unless stated in the Owners Manual 2 Roundup reserves the right to make changes in design or add any improvements on any product The right is always reserved to modify equipment because of factors beyond our control and government regulations Charges to update equipment do not constitute a warranty charge 3 If shipment is damaged in transit the purchaser should make his claim directly upon the carrier Careful inspection should be made of the shipment as soon as it arrives and visible damage should be noted upon the carrier receipt Damage should be reported to the carrier This damage is not covered under this warranty 4 Warranty charges do not include freight or foreign excise municipal or other sales or use taxes All such freight and taxes are the responsibility of the purchaser 5 THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE
12. he unit Install new light into place until flush Reinstall wiring onto light Test unit for proper operation Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 TESTING PAN See Pan under Component Description amp Function before proceeding The pan is typically trouble free If it is damaged it must be replaced Replacement Procedure Remove the bottom panel Remove the pan s 4 hex nuts Remove pan Install new pan amp secure with hex nuts Test unit for proper operation AR CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 TESTING BASKETS See Baskets under Component Description amp Function before proceeding The baskets are typically trouble free If they are damaged they must be replaced Replacement Procedures Remove baskets Install new baskets Af CCC 20 TECHNICAL MANUAL Antunes amp LAST UPDATE 5 1 05 1060005 5 05
13. ing each component must be tested individually TESTING POWER SWITCH See Power Switch amp Splash Guard under Component Description amp Function before proceeding Disconnect wires to isolate switch Turn switch to the position Verify continuity across terminals 1 amp 2 then 4 8 5 Next turn switch to the Off position Reading should now be infinity Replace if fails test Replacement Procedures Remove service panel Disconnect power switch wires Mark for reinstallation Squeeze locking tabs inward amp push switch amp splash guard away from unit Install new switch along with the splash guard NOTE If splash guard is damaged or missing it must be replaced Failure to do so may result in water moisture damage to electrical components Reinstall wiring onto switch Test unit for proper operation Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 TESTING SPLASH GUARD See Splash Guard under Component Description amp Function before proceeding The splash guard is typically trouble free If it is damaged or missing it must be replaced Replacement Procedures Remove service panel Disconnect power switch wires Mark for reinstallation Squeeze locking tabs inward amp push switch away from unit Reinstall switch amp new splash guard NOTE If splash guard is damaged or missing it must be replaced Failure to do so may result in water moistu
14. lution CCC 20 TECHNICAL MANUAL LAST UPDATE 5 1 05 1060005 5 05 INSTALLATION Unpacking Safety Interlock Switch Beneath Head Assembly 1 Remove unit and all packing materials from ship ping carton 2 Open the large box Remove all packing materi als and protective coverings from the unit and parts 3 Wash baskets in soap and water Wipe all sur faces of the unit with a hot damp cloth NOTE Do not use a dripping wet cloth Wring out before use 4 Install baskets into unit NOTE If any parts are missing or damaged con tact Antunes Technical Service IMMEDIATELY at 1 877 392 7854 Figure 1 Corn Cooker Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 Fs INSTALLATION WARNING 4 Equipment Setup When placing the unit into service pay attention to the following guidelines Make sure the controls are positioned at the rear to ensure adequate room for loading and unload ing baskets Make sure power to the unit is off and the unit is at room temperature Do not block or cover any openings on the unit Do not immerse cord or plug in water Keep cord away from heated surfaces Do not allow cord to hang over edge of table or counter Connect the unit to the power supply Refer to the specification plate for the proper voltage All electrical connections must be in accordance with local electrical codes and any other appli cable codes
15. r Do not attempt to defeat the grounded connector Install or locate the equipment only for its intended use as described in this manual Do not use corrosive chemicals in this equipment Do not operate this equipment if it has a damaged cord or plug if it is not working properly or if it has been damaged or dropped This equipment should be serviced by qualified personnel only Contact the nearest Roundup authorized service facility for adjustment or repair Do not block or cover any openings on the unit AR Antunes amp Co Do not immerse cord or plug in water Keep cord away from heated surfaces Do not allow cord to hang over edge of table or counter The following warnings and cautions appear throughout this manual and should be carefully observed Turn the unit off disconnect the power source and allow unit to cool down before performing any service or maintenance on the unit The unit should be grounded according to local electrical codes to prevent the possibility of electrical shock It requires a grounded receptacle with separate electrical lines protected by fuses or circuit breaker of the proper rating All electrical connections must be in accordance with local electrical codes and any other applicable codes CCC 20 TECHNICAL MANUAL LAST UPDATE 5 1 05 1060005 5 05 AR Antunes amp Co A WARNINGS A WARNING ELECTRICAL SHOCK HAZARD FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS I
16. r switch amp electrical components within the electrical compartment NOTE The PVC boot must always be used Failure to do so may result in water moisture damage to electrical components Safety Interlock Switch A normally open N O momentary switch that is used to prevent operation of the heating element in the event the head assembly is not properly seated onto the pan or is being operated without the pan The switch has an actuating plunger which protrudes from beneath the head assembly Provided the head assembly is properly seated onto the pan the weight of the head assembly allows the plunger to become depressed therefore closing its contacts Safety Interlock Switch O ring An o ring that fits over the plunger of the switch It helps prevent water moisture from entering amp damaging the safety interlock switch amp electrical components within the electrical compartment NOTE The o ring must always be used Failure to do so may result in water moisture damage to electrical components Terminal Block A three pole six terminal junction block It links the incoming power cord wires L1 N Ground to the safety interlock switch power switch amp chassis ground Heating Element It is an M shape element that is attached to the head assembly amp is positioned at the bottom of the pan It heats the water until it is cycled off by the thermostat Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 10
17. re damage to electrical components Reinstall wiring onto switch Test unit for proper operation Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 TESTING SAFETY INTERLOCK SWITCH See Safety Interlock Switch under Component Description amp Function before proceeding Disconnect wires to isolate switch Verify continuity across the switch with the plunger manually depressed Next release plunger Reading should now be infinity Replace if fails test Replacement Procedures Remove service panel Disconnect switch wires Remove the two mounting screws Install new switch along with the new o ring amp secure with screws NOTE The o ring must always be used Failure to do so may result in water moisture damage to electrical components Reinstall wiring onto switch Test unit for proper operation Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 TESTING SAFETY INTERLOCK SWITCH O RING See Safety Interlock Switch O ring under Component Description amp Function before proceeding The safety interlock switch o ring is typically trouble free If it is damaged it must be replaced Replacement Procedures Follow the safety interlock switch replacement procedures NOTE The o ring must always be used Failure to do so may result in water moisture damage to electrical components Test unit for proper operation Af CCC 20 TEC
18. serve when the cob core temperature reaches 150 F 68 C NOTE All models except Mfg No 9600214 are equipped with a green READY indicator Figure 2 that lights when water operating temperature is reached Mfg No 9600214 is equipped with a Heater indica tor that lights when heating element is on amp turn off when the Heating Element is off 5 Use the front basket as the serving basket and the rear basket as the holding basket Serve corn from the front basket until it is empty then rotate the corn from the rear to the front basket This method helps to keep track of which corn has been cooking the longest Built in Power Rocker Switch Indicator Power On Off Light All models except Mfg No 9600214 indicator light comes on when unit is up to operating temperature Mfg No 9600214 only indicator light comes on when heating element is on Figure 2 Controls Unsold Corn Carefully plan and schedule the loading of corn so that only a small amount is left at the end of the day Any leftover corn can be prepared for use the next day by performing the following steps 1 Remove corn from the cooker and place in a con tainer Handle the carefully to prevent dam age to the kernels 2 Cover corn with shaved ice or ice cubes and place in freezer 3 Reheat the corn the same way as heating uncooked corn LAST UPDATE 5 1 05 1060005 5 05 Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co CCC
19. should be performed by qualified service personnel The unit should be unplugged when servicing except when electrical tests are required Use extreme care during electrical circuit tests Live circuits will be exposed but the unit does not heat and the plugged in outlet Loose burnt broken wires Tighten wires and replace if burned circuit or charred Inoperable Rocker Switch Replace Rocker Switch Safety Interlock Switch not engaged Reposition the Head Assembly to engage the Safety Interlock Switch according to the operating instruc tions in this manual Unit overheats or overcooks water Inoperable Thermostat Replace the Thermostat boils Water level is too low Add water so that the corn is com pletely covered Unit under cooks the corn Inoperable Thermostat Replace the Thermostat Rocker Switch power On Off is ON Inoperable Heating Element Replace the Heating Element the unit does not heat but the light Inoperable Thermostat Replace the Thermostat circuit Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 CCC 20 Parts Testing amp Replacement Procedures Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 TESTING HEAD ASSEMBLY See Head Assembly under Component Description amp Function before proceeding If any of the head assembly s electrical components are malfunction
20. ter and to allow adequate room for loading and unload ing of baskets it Well T HENT in nn Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 SPECIFICATIONS Electrical Ratings Model amp Voltage Mfg No so gt 9600200 20 208 240 1560 2090 7 5 8 6 50 50 9600202 20 208 240 1560 2090 7 5 8 6 50 60 9500214 20 208 240 1560 2090 7 5 8 6 50 60 9500215 Mfg China 20 120 1750 15 0 50 60 9600217 Mfg China Electrical Cord amp Plug Configurations Letter Description Configuration Commercial Cord Harmonized Cord CEE 7 7 16 250 VAC Assembly Only 5 15P 15 Amp 120 VAC SS Non Locking Assembly Only ri Indicates that the plug comes with a Harmonized Cord Indicates that the plug comes with a Commercial Cord TP Antunes amp Co ELECTRICAL SHOCK HAZARD FAILURE TO FOLLOW THE INSTRUCTIONS IN THIS MANUAL COULD RESULT IN SERIOUS INJURY OR DEATH Electrical ground is required on this appliance Do not modify the power supply cord plug If it does not fit the outlet have a proper outlet installed by a qualified electrician Do not use an extension cord with this appliance Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded All electrical connections m
21. ust be in accordance with local electrical codes and any other appli cable codes Capacity Quantity eighty 3 ears of corn Shipping Weight 30 Ibs 13 6 kilos CCC 20 TECHNICAL MANUAL LAST UPDATE 5 1 05 1060005 5 05 A WARNINGS Throughout this manual you will find the following safety words and symbols that signify important safety issues with regards to operating or maintaining the equipment GENERAL WARNING Indicates informa ELECTRICAL WARNING Indicates infor tion important to the proper operation of mation relating to possible shock hazard the equipment Failure to observe may Failure to observe may result in damage result in damage to the equipment and or to the equipment and or severe bodily severe bodily injury or death injury or death CAUTION Ped WARNING End GENERAL CAUTION Indicates informa HOT SURFACE WARNING Indicates tion important to the proper operation of information important to the handling of the equipment Failure to observe may equipment and parts Failure to observe result in damage to the equipment caution could result in personal injury Af CCC 20 TECHNICAL MANUAL A J Antunes amp Co LAST UPDATE 5 1 05 1060005 5 05 A WARNINGS In addition to the warnings and cautions in this manual use the following guidelines for safe operation of the unit Read all instructions before using equipment For your safety the equipment is furnished with a properly grounded cord connecto
Download Pdf Manuals
Related Search