Shark BG-3030 Operating instructions
Contents
1. C The pump in this machine is susceptible to permanent damage if frozen FREEZE DAMAGE IS NOT COVERED BY WARRANTY 1 Stop the pressure washer squeeze spray gun trig ger to release pressure 2 Detach water supply hose and high pressure hose 3 Turn on the machine for a few seconds until re maining water exits Turn engine off immediately 4 Drain the gas and oil from the engine 5 Do not allow high pressure hose to become kinked 6 Store the machine and accessories in a room which does not reach freezing temperatures CAUTION Failure to follow the above directions will result in damage to your pressure washer When the pressure washer is not being operated or is being stored for more than one month follow these instructions 1 Replenish engine oil to upper level 2 Drain gasoline from fuel tank fuel line fuel valve and carburetor 3 Pour about one teaspoon of engine oil through the spark plug hole pull the starter grip several times and replace the plug Then pull the starter grip slowly 97 705 97 706 97 707 REV 4 04 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION LOW OPERATING Insufficient water supply Closed Use larger garden hose clean inlet water PRESSURE faucet screen Open faucet Old worn or incorrect spray nozzle Match nozzle number to machine and or replace with new nozzle Plumbing or hose leak Check plumbing system for leaks Retape leaks with teflon tape Faulty or misadjusted unloader Ad2. such as frames handles coil wraps float tanks and belt guards Forged brass pump manifold All heating coils will have a three year warranty Internal components on the oil end of all pressure washer pumps will have a seven year warranty ONE YEAR PARTS WARRANTY All other components excluding normal wear items as described below will be warranted for one year on parts Warranty on these parts will be for one year regardless of the duration of the original component manufacturer s part warranty WARRANTY PROVIDED BY OTHER MANUFACTURERS Motors generators and engines which are warranted by their respective manufacturers are serviced through these manufac turers local authorized service centers SHARK cannot provide warranty on these items WHAT THIS WARRANTY DOES NOT COVER This warranty does not cover the following items 1 Normal wear items such as nozzles guns discharge hoses wands quick couplers seals filters gaskets O rings packings pistons pump valve assemblies strainers belts brushes rupture disks fuses pump protectors 2 Damage or malfunctions resulting from accidents abuse modifications alterations incorrect installation improper servicing failure to follow manufacturer s maintenance instructions or use of the equipment beyond its stated usage specifications as contained in the operator s manual Damage due to freezing chemical deterioration scale buildup rust corrosion or thermal expansion Dam
3. 07104001 02 2 0 Hose 566 Specifications pages 18 19 Bracket Take Up CW Red 1 97 705 97 706 97 707 REV 4 95 07104948 ITEM 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 QTY olej OIOI I gt O EXPLODED VIEW PARTS LIST DESCRIPTION Slider Pump Bushing 5 8 Snap Pump Protector 1 4 Nipple 3 8 Fem x 3 8 Washer 1 4 Bolt 1 4 x 3 4 Flange Adaptor 1 4 x 1 8 252737 Bolt 5 16 x 1 NC Washer 5 16 Nut 5 16 ESNA Bolt 3 8 x 2 1 4 Bolt 8mm x 30mm Hex Washer 1 4 Flat SAE Nut 1 4 ESNA NC PART NO 95 07104710 2 01403 2 300812 2 2006 90 4000 90 19710 2 11031 90 1007 90 4001 90 2001 90 10201 90 1030 90 4000 90 2000 ITEM 59 60 61 62 63 64 65 66 67 68 69 70 71 72 QTY 1 DESCRIPTION PART NO Nozzle See Specifications pages 18 19 for Nozzle Compl Detergent Nozzle SACQMEG 0003 0 Red Nozzle SAQCMEG 1503 0 Yellow Nozzle SAQCMEG 2503 0 Green Nozzle SAQCMEG 4003 0 White Nozzle SACQMEG 0003 5 Red Nozzle SAQCMEG 1503 5 Yellow Nozzle SAQCMEG 2503 5 Green Nozzle SAQCMEG 4003 5 White Nozzle SACQMEG 0004 5 Red Nozzle SAQCMEG 1504 0 Yellow Nozzle SAQCMEG 2504 0 Green Nozzle SAQCMEG 4004 0 White 97 705 97 706 97 707 REV 4 nozzle size 4 16540 4 12803000 4 12803015 4 128030
4. 3029 11 5 0105 2BK90H 5 40509001 BX 373539 3 7 3500 4 0 HM4035 5 1220 5 3029 13 5 010721 2BK90H 5 40509001 2 BP 282037 2 8 2000 4 0 0 5 1625 5 3151 5 5 5 0104 BK80H 5 40408001 BP 252731 2 5 2700 3 0 EZ3042S 5 2315 5 3025 6 5 5 01041 BK80H 5 40408001 LU BP 303031 3 0 3000 ti EZ3042S 5 2315 5 3025 9 5 0102 2AK74H 5 40207401 5 BP 353237 ti 3200 4 0 GM4035 5 1920 5 3029 11 5 0105 2BK90H 5 40509001 wa BP 373537 3500 4 0 GM4035 5 1920 5 3029 13 5 010721 2BK90H 5 40509001 0 BG 282037 2 8 2000 4 0 WML 2540 5 1625 5 3151 5 5 5 0104 BK80H 5 40408001 Am BG 252731 2 5 2 00 3 0 EZ3042S 5 2315 5 3025 6 5 5 01041 BK80H 5 40408001 8 BG 303031 3 0 3000 360 EZ3042S 5 2315 5 3025 9 5 0102 2AK74H 1 BG 353237 J5 3200 4 0 GM4035 5 1920 5 3029 11 5 0105 2BK90H 5 40509001 BG 373537 3 7 3500 4 0 GM4035 5 1920 5 3029 13 5 010721 2BK90H 5 40509001 SPECIFICATIONS p m Pump Bushing Engine Pulley Engine Bushing Belt Belt Y Model Bushing Part No Pulley Part Bushing Part No Size Part No 5 BX 282039 24MM 5 512024 BK27x3 4 9 40402775 n a n a BX32 5 602032 J BX 252731 24MM 5 512024 BK27x3 4 5 40402775 n a n a BX32 5 602032 BX 303031 24MM 5 512024 2AK28x 5 402028010 n a n a AX38 2 5 602038 BX 353239 24MM 5 512024 2BK32H 5 40503201 HX1 5 11100 BX39 2 5 604039 V BX 373539 24MM 5 512024 2BK32H 5 40503201 HX1 5 11100 BX39 2 5 604039 BP 282037 24MM 5 512024 BK27x3 4 9 40402775 n a n a BX32 5 602032 JJ BP 252731 24MM 5 512024 BK27x3 4 5 404027
5. defects or other reproductive harm WARNING Flammable liquids can create fumes which can 19 nite causing property damage or severe injury WARNING Risk of fire Do not add fuel when the product is operating WARNING Risk of explosion Do not spray flammable liquids 4 Do not place machine near flammable objects as the engine is hot 5 Allow engine to cool for 2 minutes before refueling If any fuel is spilled make sure the area is dry be fore testing the spark plug or starting the engine Fire and or explosion may occur if this is not done Refuel gasoline engines on mobile or portable equipment a outdoors b with the engine on the equipment stopped c with no source of ignition within 10 feet of the dispensing point and d with an allowance made for expansion of the fuel should the equipment be exposed to a higher ambient temperature In an overfilling situation additional precautions are necessary to ensure that the situation is handled in a safe manner WARNING High pressure stream of water that this equip ment can produce can pierce skin and its underlying tissues leading to serious injury and possible amputation 4 WARNING RISK OF ASPHYXIATION USE ONLY IN A WELL VENTILATED AREA 4 WARNING RISK OF FIRE DO NOT ADD FUEL WHEN OPERATING MACHINE 4 WARNING HIGH PRESSURE SPRAY CAN PIERCE SKIN AND TISSUES INTRODUCTION Thank you for purchasing this Pressure
6. 25 4 12803040 4 12803500 4 12803515 4 12803525 4 12803540 4 12804000 4 12804015 4 12804025 4 12804040 ITEM 58 or LU I x s op co Q l 5 0 tc gt cc a G m U c m S I m I 5 m 2 WY gt HOSE amp SPRAY GUN ASSEMBLY HOSE amp SPRAY GUN ASSEMBLY PARTS LIST ITEM PART NO DESCRIPTION QTY ITEM PART NO DESCRIPTION QTY 1 4 0110303 Wand Assy 35 1 2 Side Grip 7 3 12021 Injector Detergent Non Adjust w Couplers BX Models 1 3 5 3 1 4 0110322 Wand Assy Side Grip 8 2 9040 Clamp Hose 2 w 1 4 Coupler 35 1 2 eee BG BP Models 1 9 4 02080000 Tube 1 4 x 1 2 Clear Vinyl 6 ft 2 4 012401 Spray Gun Assy BX Models 1 10 2 1904 Strainer 1 4 01246 Spray Qun AP 1000 1 3 2 2000 Coupler 1 4 Female Brass 2 4 Nozzle See Machine Breakdown for Part Numbers Page 15 16 Hose 566 Specifications Pages 18 19 2 2003 Coupler 3 8 Male Brass 1 97 705 97 706 97 707 REV 4 04 97 705 97 706 97 707 REV 4 04 2 SPECIFICATIONS O AM Pressure Nozzle Pump Unloader Engine Engine Pump Pump Pulley Model GPM PSI Size Pump Part PartNo HP Part Pulley Part No x BX 282039 2 8 2000 4 0 HC340R 5 1800 5 3309 5 5 5 0104 BK80H 5 40408001 S1 BX 252731 2 5 2 00 3 0 EZ3042S 5 2315 5 3025 6 5 1 BK80H 5 40408001 6 1 3 0 3000 5 EZ3042S 5 2315 5 3025 9 5 0102 2AK74H 5 40207401 Tr BX 353239 35 3200 4 0 HM4035 5 1220 5
7. 75 n a n a BX32 5 602032 a 303031 24MM 5 512024 2AK28x 5 402028010 n a n a AX38 2 5 602038 BP 353237 24MM 5 512024 2BK32H 5 40503201 HX 1 5 11100 BX39 2 5 604039 0 BP 373537 24MM 5 512024 2BK32H 5 40503201 HX 1 5 11100 BX39 2 5 604039 gt BG 282037 24MM 5 512024 BK27x3 4 5 40402775 n a n a BX32 5 602032 BG 252731 24MM 5 512024 BK27x3 4 9 40402775 n a n a BX32 5 602032 BG 303031 24MM 5 512024 2AK28x 5 402028010 n a n a AX38 2 5 602038 0 00 3532837 24MM 5 512024 2BK32H 5 40503201 HX1 5 11100 BX39 2 5 604039 BG 373537 24MM 5 512024 2BK32H 5 40503201 HX1 5 11100 BX39 2 5 604039 97 705 97 706 97 707 REV 4 04 m Y JJ m S m JJ D lt aa ap BG SERIES PRESSURE WASHER Shark WARRANTY ressure Washers SHARK LIMITED NEW PRODUCT WARRANTY PRESSURE WASHERS WHAT THIS WARRANTY COVERS All SHARK PRESSURE WASHERS are warranted by SHARK to the original purchaser to be free from defects in materials and workmanship under normal use for the periods specified below This Limited Warranty is subject to the exclusions shown below is calculated from the date of the original purchase and applies to the original components only Any parts replaced under this warranty will assume the remainder of the parts warranty period This warranty applies to the original purchaser and is not transferable LIMITED LIFETIME PARTS WARRANTY Components manufactured by SHARK
8. E CAUSE SOLUTION OIL SQUIRTS OUT OF Pump over filled with oil Maintain oil level at red dot on sight glass at rear OIL CAP ON PUMP of pump or at top of notch on dipstick ENGINE OPERATES Not enough gas or engine oil Fill tank with gas Check oil level FOR 15 MIN THEN STOPS Vapor lock developed by heat of Keep gas tank full to avoid vapor locking day Obstruction in fuel filter Clean or replace fuel filter WATER DRIPPING Piston packing worn Call technical support FROM UNDER PUMP I I I O Ring plunger retainer worn Call technical support Cracked piston Call technical support OIL DRIPPING Call technical support WATER LEAKING Spray gun closed with machine Open spray gun or turn off machine FROM PUMP running 2 minutes or longer PROTECTOR Excess water supply pressure Place a pressure regulator at end of 50 garden hose V m 0 I m gt m I S z D 0 5 Q Q 97 705 97 706 97 707 REV 4 04 PREVENTATIVE MAINTENANCE This pressure washer was produced with the best available materials and quality craftsmanship However you as the owner have certain responsibilities for the correct care of the equipment Attention to regular preventative maintenance procedures will assist in preserving the performance of your equipment Contact your dealer for maintenance Regular preventative maintenance will add many hours to the life of your pressure washer Perform maintenance more
9. Hose 46 54 ST 2 Washer 3 8 Lock 4 Injector Detergent Non Adj 3 5 GPM 0 083 1 Hose 1 4 Push On Fuel Line 1 ft Hose Barb 1 4 Barb x 1 8 ML Pipe 90 1 Hose Barb 1 4 Barb 1 8 ML Pipe 1 Valve E Z Start 3 8 MPT x 1 8 FPT 1 Elbow 3 8 Street Pump Protector 1 2 PTP 1 PART NO 90 1001 90 3096 90 102751 90 10077 2 9040 90 4009 4 011184 4 02100000 2 1088 2 1084 2 3100544 2 0031 2 30082 Pump See Specifications pages 18 19 Unloader See Specifications pages 18 19 Nipple 3 8 x 3 8 NPT ST Male 1 Swivel 1 2 MP x 3 4 GHF w Strainer 1 Strainer 1 2 PA Inline Plastic 1 Label Danger Cool Engine 1 2 2007 2 10942 2 1923 10 02029 Engine See Specifications pages 18 19 Engine Pulley See Specifications pages 18 19 Engine Bushing See Specifications pages 18 19 Belts See Specifications pages 18 19 Pump Bushing See Specifications pages 18 19 Pump Pulley See Specifications pages 18 19 Handle Bumper Red 1 Label Hot Caliente w Arrows Warning 1 Label Intended For Outdoor Use 1 Label Clear Lexan 2 1 4 x 4 1 2 1 95 07104922 10 02025A 10 08017 10 9999 ITEM 29 30 31 32 33 34 35 36 3 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 o7 DESCRIPTION Grommet Rubber Nozzle Holder Handle Grab Red Label BX Models Label BG Models La
10. INSTRUCTIONS CONT gt lt 9 AV gt 6 lt NN b On Off II c WW KS PRESSURE WASHER STEP 8 Turn the engine switch to On position STEP 9 Pull the starter grip If the engine fails to start engine warms up enough to run smoothly move choke to run position and throttle to fast position CAUTION Small engines may kick back Do not hold pull starter grip tightly in hand x 5 40 S q ir 5 NOZZLES Safety Latch A WARNING Never replace The five color coded quick connect nozzles provide a wide array of spray nozzles engaging the widths from 0 510 45 and are easily accessible when placed in the conve safety latch on the spray gun nient rubber nozzle holder which is provided on the front of the machine trigger NOTE For amore gentle rinse select the white 40 or green 25 nozzle To scour the surface select the yellow 15 or red 0 nozzle To apply deter gent select the black nozzle 97 705 97 706 97 707 REV 4 04 411 LIEFE L 5 Q 0 0 lt SHUTTING DOWN AND CLEAN UP STEP 3 Turn off water supply High Pressure Outlet STEP 7 Engage the spray gun safety lock STEP 2 Turn off the engine STEP 6 Disconnect the high pressure hose from high pres sure outlet STEP 1 Remove detergent suction tube from container and insert into one gallon of fresh water Slide nozzle forward for low p
11. SS MODEL BG 2 1 OPERATING INSTRUCTION Wash ressure Washers AND PARTS MANUAL E BG 2527 0 0 2 5 For technical assistance or the SHARK dealer nearest you call 1 800 771 1881 or visit our website at www shark pw com 97 707 CONTENTS Important Safety Information ade 4 5 Component Identification 0 6 Assembly Instructions pp 7 Operating InstrUCHONS ssenarinin aea a i ai 8 9 Applying Detergent and General Operating Iechniques 10 Shut Down and Clean Up pp 11 OU 11 00 2 50 12 13 Preventative Maintenance pp 14 OMENS 14 E P0061 1600 casts rere ns tetris 0 02 ae 15 Exploded View Parts List 4 16 Hose and Spray Gun Assembly pp 17 Warranty Model Number Serial Number Date of Purchase The model and serial numbers will be found on a decal attached to the pressure washer You should record both serial number and date of purchase and keep in a safe place for future reference 97 705 97 706 97 707 REV 4 04 D m 0 c m S I m I 5 m 2 G WARNING Risk of asphyxiation Use this product only in a well ventilated area 3 Avoid installing machines in small areas or near exhaust fans Exhaust contains poi sonous carbon monoxide gas exposure may cause loss of consciousness and may lead to death It also contains chemicals known in certain quantities to cause cancer birth
12. Washer All information in this manual is based on the latest product information available at the time of printing We reserve the right to make changes at any time with out incurring any obligation This model was designed for maximum use of 8 hours per day 5 days per week Owner User Responsibility The owner and or user must have an understanding of the manufacturer s operating instructions and warnings before using this pressure washer Warning informa tion should be emphasized and understood If the op erator is not fluent in English the manufacturer s in structions and warnings shall be read to and discussed with the operator in the operator s native language by the purchaser owner making sure that the operator comprehends its contents Owner and or user must study and maintain for future reference the manufacturers instructions The operator must know how to stop the machine quickly and understand the operation of all controls Never permit anyone to operate the engine without proper instructions This manual should be considered a permanent part of the machine and should remain with it if machine is resold When ordering parts please specify model and serial number MACHINE SAFETY CAUTION To reduce the risk of injury read operating instruc tions carefully before using 1 Read the owner s manual thoroughly Failure to follow in structions could cause mal function of the machine and result in d
13. age to components from fluctuations in electrical or water supply Normal maintenance service including adjustments fuel system cleaning and clearing of obstructions Transportation to service center shop labor charges field labor charges or freight damage WHAT YOU MUST DO TO OBTAIN WARRANTY SERVICE While not required for warranty service we request that you register your SHARK pressure washer by returning the completed registration card In order to obtain warranty service on items you must return the product to an Authorized SHARK Dealer freight prepaid with proof of purchase within the applicable warranty period If the product is permanently installed you must notify your Authorized SHARK Dealer of the defect The Authorized Dealer will file a claim which must subsequently verify the defect In most cases the part must be returned to SHARK freight prepaid with the claim For warranty service on components warranted by other manufacturers the Authorized Dealer can help you obtain warranty service through these manufacturers local authorized service centers o m e cu LIMITATION OF LIABILITY SHARKS liability for special incidental or consequential damages is expressly disclaimed In no event shall SHARKS liability exceed the purchase price of the product in question SHARK makes every effort to ensure that all illustrations and specifica tions are correct however these do not imply a warranty that the product is merchantable or f
14. ap and the oil filler neck Be sure the machine is level when checking the oil level install oil dipstick Check pump oil Refer to the engine s operating manual included with machine We rec level by using dipstick or observe ommend that the oil be changed after the first 5 hours of use then once oil level in oil window if equipped every 50 hours Note Improper oil levels will cause low oil sensor to shut Use 30 wt non detergent oil off engine IMPORTANT Do not run engine with high or low oil levels as this will cause engine damage 5 oO D Gj gt lt Source STEP 3 Fill gas tank with STEP 4 Connect garden hose to STEP 5 Trigger the spray gun leaded gasoline Do not use the cold water source and turn wa to eliminate trapped air then wait leaded gasoline ter on completely Never use hot for a steady flow of water to water emerge from the spray nozzle SS IN We 2 Ai SS AM SS STEP 6 Hotate the fuel shut off valve to the On STEP 7 Move the choke lever to the Choke posi position Slide the fuel valve lever to the ON posi tion on a warm engine leave the choke lever in the tion When the engine is not in use leave the fuel run position Move the choke lever to the Closed valve in the OFF position position To restart a warm engine leave the choke mo a as lever in the Open position 97 705 97 706 97 707 REV 4 04 OPERATING
15. bel BP Models Plate Warning Instr Red QTY C7 Hanger Hose Wand Bolt Carriage 1 4 20 1 3 4 Zinc Label Belt Guard BP Label Belt Guard BX Label Belt Guard BG Nut 1 4 ESNA NC Nut 5 16 ESNA NC Nut 5 16 Flange Handle Lower Grab Red Nut 3 8 ESNA NC Washer 3 8 SAE Flat Retainer Bracket Handle Red 2 Bolt 3 8 x 2 NC HH 4 Bolt 5 16 x 1 2 5 5HP 6 5HP Honda Engines 4 Bolt 3 8 1 3 4 Tap 9HP 11HP 13HP Honda Engines Washer 3 8 x 1 Steel Pad Soft Rubber Cap 5 8 Axle Hub Black 2 Wheel amp Tire Assy 4 Steel Rim w Tube 2820 2527 2 Wheel amp Tire Assy 6 Steel Rim w Tube 3030 3532 3735 2 Frame Assy Large 1 Frame Small 5 5HP 6 5HP 1 Bolt 5 16 2 NC Carriage Zinc Nut 5 16 ESNA NC 8 Washer 5 16 Flat SAE 6 Axle 5 8 x 26 25 L 3030 3735 1 Axle 5 8 x 19 5 8 2527 2820 1 Slider Pump 1 Guard Belt 303037 1 Guard Belt All Models Except 303037 1 l T N l gt gt PART NO 2 0103 95 07104921 11 0359 11 0358 11 0360 95 07104945 95 07102382 90 100473 11 3199 11 32289 11 3229 90 2000 90 2001 90 20012 95 07104920 90 2002 90 4002 95 07104923 90 1020 90 1009 90 1019 90 40125 2 01041 2 4 0303 4 0307 95 07104991 95 07104963 90 10072 90 2001 90 4001 95 07104000 95 07102313 95
16. bolt STEP 3 Attach the spray gun hose frame of the pressure washer through the holes from the outside storage handle and bracket to Note It may be necessary to move ofthe unit and attach a nut from the handle Tighten nuts the handle supports from side to inside of the machine Tighten nuts side in order to align the handle so it will slide over the frame supports Pressure Pressure Nozzle Nozzle Wand UL Oy Wand Coupler x E 4 S q ir Q Coupler High Pressure Hose Collar STEP 4 Attach the high pressure STEP 5 Pull the spring loaded col STEP 6 Release the coupler col hose the spray gun using teflon lar of the wand coupler back to in lar and push the nozzle until the tape on hose threads sert your choice of pressure nozzle collar clicks Pull the nozzle to make sure it is seated properly Source STEP 7 Connect high pressure STEP 8 Connect garden hose to hose to pump discharge fitting Push the cold water source coupler collar forward until secure Pump Water Inlet STEP 9 Connect the garden hose to pump water inlet Inspect inlets CAUTION Do not run the pump without water or pump dam age will result 97 705 97 706 97 707 REV 4 04 OPERATING INSTRUCTIONS Pump Oil Dipstick Engine Oil Dipstick 211 LIEFE L STEP 1 Check engine oil level Oil level should be level with the bottom of STEP 2 Remove shipping c
17. eath serious bodily injury and or property dam age 2 Allinstallations must comply with local codes Con tact your electrician plumber utility company or the selling distributor for specific details 46 CAUTION READ OPERATOR S MANUAL THOROUGHLY PRIOR USE 97 705 97 706 97 707 REV 4 A WARNING WARNING High pressure spray can cause paint chips or other particles to become airborne and fly at high speeds To avoid personal injury eye safety de vices must be worn PROTECTIVE EVEWEAR AND 6 Eye safety devices and foot CLOTHING MUST protection must be worn when BE WORN using this equipment 7 High pressure developed by these machines will Cause personal injury or equipment damage Use caution when operating Do not direct discharge stream at people or severe injury or death will re sult 8 Never make adjustments on machine while in op eration 9 Do not operate with spray gun in the off position for extensive periods of time as this may cause damage to the pump 10 The best insurance against an accident is precau tion and knowledge of the machine 11 Manufacturer will not be liable for any changes made to our standard machines or any compo nents not purchased from us 12 Read engine safety instructions provided OPERATOR S MANUAL PRESSURE WASHER A WARNING WARNING Keep water spray away from electrical wiring or fa tal electric shock may result gt 13 N
18. ever run pump dry or leave Z7 spray gun closed longer than 5 minutes 14 Do not allow children to oper SE non ate the pressure washer at ELECTRICAL any time WIRING 15 Inlet water supply must be cold and clean fresh water 97 705 97 706 97 707 REV 4 0 m N c D m gt T m I S m ke 60 gt 2 COMPONENT IDENTIFICATION Unloader Detergent Injector Garden Hose not included Detergent Bucket not included Wand Must be connected to the spray gun High Pressure Hose Connect one end to water pump discharge nipple and the other end to spray gun Note If trigger on spray gun is released for more than 2 minutes water may leak from valve Warm water will discharge from pump protector onto floor This system prevents internal pump damage Straight Spray Gun Trigger S sk i CZ ed Starter Grip SN High Pressure Hose Pump Develops high pressure Starter Grip Used for starting the engine manually Spray Gun Controls the application of water and detergent onto cleaning surface with trigger device In cludes safety latch Detergent Injector Allows you to siphon and mix detergents 97 705 97 706 97 707 REV 4 04 ASSEMBLY INSTRUCTIONS Carriage Hose Spray Gun Bolt al Storage Bracket Alignment gt gt Holes PRESSURE WASHER STEP 1 Attach the handle to the STEP 2 Insert the carriage
19. it for a particular purpose or that the product will actually conform to the illustrations and specifications THE WARRANTY CONTAINED HEREIN IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTY OF FITNESS FOR A PAR TICULAR PURPOSE SHARK does not authorize any other party including authorized Dealers to make any representation or promise on behalf of SHARK or to modify the terms conditions or limitations in any way It is the buyer s responsibility to ensure that the installation and use of SHARK products conforms to local codes While SHARK attempts to assure that its products meet national codes it cannot be responsible for how the customer chooses to use or install the product SHARK PRESSURE WASHERS 1 360 833 9100 1 800 771 1881 www shark pw com SHARK BG 97 707 REV 4 ressure Washers Form 97 707 Revised 4 04 Printed in U S A
20. just unloader for proper pressure Install valve repair kit when needed Call technical support Worn packing in pump Call technical support Machine has been stored in Thaw out machine completely including hose freezing temperatures spray gun and wand Slow engine RPM Call technical support FLUCTUATING Worn pump valves Call technical support PRESSURE Dirt in pump valves Call technical support Pump sucking air Check all pump lines and connections 2 a aa W S s 0 QO PRESSURE LOW Nozzle worn Replace nozzle AFTER PERIOD OF NORMAL USE Unloader valve worn Replace unloader valve ENGINE WILL NOT START Low oil shutdown Fill engine with oil OR STOPS WHILE OPERATING ENGINE IS Nozzle partially blocked Clean nozzle OVERLOADED Excessive pressure from high Adjust engine throttle to lower RPM engine RPM WATER OR OIL LEAKING A small amount of leaking is If excessive leaking occurs call technical FROM BOTTOM OF PUMP normal support PRESSURE INCREASES Unloader valve not operating Call technical support WHEN SPRAY GUN IS properly CLOSED PRESENCE OF WATER Water sprayed at machine Change oil Direct soray away from machine IN PUMP OIL High humidity in air Check and change oil twice as often Piston packing worn Oil seal worn Call technical support 97 705 97 706 97 707 4 04 TROUBLESHOOTING PROBLEM POSSIBL
21. often under severe conditions MAINTENANCE SCHEDULE Enaine Oil Chanae First month or 20 hours g Every 100 hours or every 6 months after first month Inspect Every 50 hours Air Cleaner Filter Clean Monthly Inspect Oil level daily Pump Oil Change After first 50 hours then every 500 hours or annually Replace High Pressure Nozzle Every 6 months Replace Quick Connects Annually Clean Water Screen Filter Weekly Replace HP Hose Annually if there are any signs of wear Tighten Every 6 months Belts Inspect Replace Every 6 months iS 2 a Am LU S s 0 Q OIL CHANGE RECORD Check pump oil and engine oil level before first use of your new pressure washer Estimated Operating Estimated Operating Date Oil Changed Hours Since Last Date Oil Changed Hours Since Last Month Day Year Oil Change Month Day Year Oil Change 97 705 97 706 97 707 4 04 EXPLODED VIEW 2527 0 0 m N D m gt T m I 3 m ke 60 gt 2 19 97 705 97 706 97 707 REV 4 EXPLODED VIEW 3030 3532 3735 OPERATOR S MANUAL PRESSURE WASHER 97 705 97 706 97 707 REV 4 04 D m OD JJ m m I 5 m Q 2 V gt 5 EXPLODED VIEW PARTS LIST DESCRIPTION QTY Screw 1 4 3 4 HH NC 2 Washer 1 2 Flat SAE 2 Bolt 1 2 13 x 5 1 2 HEX 1 Bolt Carriage 5 16 x 1 3 4 Clamp
22. ressure or to connect black detergent nozzle Pull trigger on spray gun and siphon water for one minute STEP 4 Press trigger to release water pres sure den hose from the water in let on the machine STORAGE until you feel increased pressure which indicates the piston is on its compression stroke and leave it in that position This closes both the intake and ex haust valves to prevent rusting of cylinder 4 Cover the pressure washer and store in a clean dry place that is well ventilated away from open flame or sparks NOTE The use of a fuel additive such as STA BIL or an equivalent will minimize the formu lation of fuel deposits during shortage Such addi tives may be added to the gasoline in the fuel tank of the engine or to the gasoline in a storage container After Extended Storage CAUTION Prior to restarting thaw out any possible ice from pressure washer hoses spray gun or wand Engine Maintenance During the winter months rare atmospheric conditions may develop which will cause an icing condition in the carburetor If this develops the engine may run rough lose power and may stall This temporary condition can be overcome by deflecting some of the hot air from the engine over the carburetor area NOTE Refer to the engine manufacturer s manual for service and mainte nance of the engine CAUTION Always store your pressure washer in a location where the temperature will not fall below 32 F 0
Download Pdf Manuals
Related Search