Assa Abloy CL33700 TCPWI1 Specifications
Contents
1. Access 700 TCPWI1 TCPIP1 Corbin 7 Russwin Installation Instructions CL33700 TCPWI1 amp TCPIP1Series ASSA ABLOY Cylindrical Lockset FM323 3 14 Attention Installer Please read these instructions carefully to prevent missing important steps Please Note Improper installations may result in damage to the lock and void the factory warranty Important The accuracy of the door preparation is critical for proper functioning and security of this lock Misalignment can cause premature wear and a lessening of security For Technical Assistance call Corbin Russwin at 1 800 810 WIRE 9473 Copyright 2014 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited ASSA ABLOY the global leader in door opening solutions CL33700 PWI PIP Series Cylindrical Lock Corbin 7a Russwin ASSA ABLOY Table of Contents 1 Warni aonana aaa 2 General D SCriptiOn csssccssccssecsssesseecssessssesseeesseesseesseensO 3 Specifications Features ssssssssssnnnnnnunnnnnnnnnnnnnnnnnnnnnnnnnn 4 Product Illustration ccsecssscsssesssesssesssesssesssesssees 5 Installation Instructions sssssssssnsnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn D 6 TCPIP PoE Wiring INStruCtiOns csccseessessesesed 7 7 Operational CheCK cscssscssssssessesssesssessseessesseeess2. Drain Wire Cable CAT 5e 26 AWG stranded shielded 1000hm PoE Hinge Patent Pending A Ground dg D Door Harness Installation Ring Terminal Secured to Lock Mounting Plate Order of installation may vary Refer to appropriate sections for instructions 1 Prop door open 2 Tape the two lock side 4 pin connectors to the ring terminal 3 Using the ring terminal carefully fish the assembly through the door channel to the lock 4 Remove tape from ring terminal and door harness connectors Hinge side harness connectors e 4 pin male Molex connector e 6 pin male Molex connector with ground wire Lock side harness connectors e Ring terminal e 2 4 pin connectors e 4 pin Molex connector Notes 4 pin connector e Connectors go on only one way They cannot be plugged to incor rect position e Do not force and do not offset connectors e Be sure they are completely seated flush Copyright 2014 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 19 ASSA ABLOY the global leader in door opening solutions CL33700 PWI PIP Series Cylindrical Lock Corbin 7 Russwin ASSA ABLOY 6 Operationial Check IMPORTANT Be sure to test functions prior to closing door In all cases perform the following checks 1 Ensure that inside lever retracts latch and dea
3. 7a d Run wires through slots in edges of spring cassette Fig 7b Note Do not run wires through center hole and be careful not to pinch wires under spring cassette There are DOOR EDGE markings on the cassette for orientation Wire Routing This image shows wood door prep with wire run channel in inside face of door Alternate construction would be a raceway through the door core Fig 7b Detail Wire Harness Connector and Wire WD Ground Wire ers Screw Fig 7a Copyright 2014 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 9 ASSA ABLOY the global leader in door opening solutions CL33700 PWI PIP Series Cylindrical Lock Corbin 7 Russwin ASSA ABLOY 5 Installation Instructions Continued 8 Connect cables Le Connectors go on one way Each connector is Inside Face of Door mated to prevent connecting incorrectly 6 a Connect 2 pin wire to Door Status Switch 0 o Harness b Connect 4 pin connector from harness into wire from lock body c Install the rose over the inside cassette Spring Cassette 2 12 24 Screws Fig 8 9 Installation and Removal of Lever and Standard Cylinders Inside Rose LEVER STYLE REMOVAL INSTALL PLAIN LEVER PUSH RELEASE TOOL SLIDE LEVER OVER RELEASE Ay aa
4. Install Outside Escutcheon a Insert the mounting posts through holes as shown Fig 10 b On the inside of the door align mounting plate with indicated holes Fig 11a c Feed reader cable through central opening in mounting plate Fig 11a d Lockbody cable feeds from bottom Fig 11a and 11b e Make sure they are positioned upright Fig 11a Fig 10 f Insert other three 8 32 x 1 7 8 flat head machine screws and tighten fastening the outside escutcheon to the door Fig 11a Mounting Plate Mounting Plate 4 8 32 x 1 7 8 Flat Head Machine Screws 2 8 3 8 flat head Wood Screws Inside Face of Door Reader Cable DPS i jill il Position ground ring terminal Fig 11b upright then tighten screw Lock body cable Fig 11a Copyright ae Corbin Russwin ne a ASSA ABLOY group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 12 ASSA ABLOY the global leader in door opening solutions CL33700 PWI PIP Series Cylindrical Lock RUSWANA ASSA ABLOY 5 Installation Instructions Continued 11 Installation of Connectors Reader DPS 9 24VDC CAUTION Do not touch or allow debris to enter connector contacts 24 pin 4 pin Power Secure the following connectors to their respective terminals Fig 12a b a Secur
5. e Consult the dealer or an experienced technician for help The term IC before the radio certification number only signifies that Industry Canada technical specifications were met This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Operation is subject to the fol lowing two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Cet appareillage num rique de la classe B r pond a toutes les exigences de interf rence canadienne causant des r glements d quipement L op ration est sujette aux deux conditions suivantes 1 ce dispositif peut ne pas causer l interf rence nocive et 2 ce dispositif doit accepter n importe quelle interf rence re ue y compris l interf rence qui peut causer l op ration peu d sir e O To comply with Fire Listed doors the batteries must be replaced with alkaline batteries only To avoid possible damage from electrostatic discharge ESD some basic precautions should be used when handling electronic components e Minimize build up of static by touching and or maintaining contact with unpainted metal surfaces such as door hinges latches and mounting plates especially when mounting electronic components such as readers and controllers onto the door e Leave components reader and controller
6. protected in their respective anti static bags until ready for installation e Do not touch pins leads or solder connections on the circuit boards Copyright 2014 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 2 ASSA ABLOY the global leader in door opening solutions CL33700 PWI PIP Series Cylindrical Lock Corbin 7a Russwin ASSA ABLOY 2 General Description Designed specifically for the campus market the Corbin Russwin Access 700 series mortise Locks are available in WiFi PWI and PoE PIP configurations Coupled with third party software the PWI and PIP offers a complete integrated access control system The Access 700 may be used for both indoor and outdoor applications weath er protective gasket supplied The Access 700 PWI operates on six 6 AA alkaline batteries and may be used for both indoor and outdoor ap plications A weather protective gasket is provided for outdoor applications 3 Specifications Features Hardware Specifications e Latch Stainless steel 18mm throw Optional 34 19mm throw deadlocking fire latch for pairs of doors e Deadlocking latch prevents manipulation when door closed e Door Thickness 1 3 4 44mm to 2 60mm Standard Optional 2 50mm to 2 1 4 67mm optional e Outside lever controlled by keyp
7. Door sree or arPostin sme For parts not listed refer to CL3300 Parts and Service Manual Copyright 2014 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 5 ASSA ABLOY the global leader in door opening solutions CL33700 PWI PIP Series Cylindrical Lock Corbin 7 Russwin 5 Installation Instructions l Verify Hand and Bevel of door Illustrations shown are as viewed from the outside or secure side of opening EE SS al E Left Hand Left Hand Right Hand Right Hand Hinges Left Reverse Bevel Hinges Right Reverse Bevel Open Inward Hinges Left Open Inward Hinges Right LH Open Outward RH Open Outward LHRB RHRB 2 Prep door according to supplied Door Marker FM302 For door manufacturer templates visit www corbinrusswin com and reference Template 131077 Outside of Door Ss Escutcheon Through Bolt Holes Door Position Controller Wire Hole i Switch 02 we Lockbody Through Bolt Holes gt O Alignment Notches Latch Front and Hole Q o Lock Body Prep mi Esn i Q Inside of Door ee TT i n Inside Mouthing Plate Holes O Controller Wire Hole O Escutcheon Through Bolt Holes O Wire Run Channel Lock Body Through Bolt Holes Alignment Notches a wer Lock Bod
8. given in inches mm IBLE Pal lt CYLINDER TAILPIECE CYLINDER FOR 7 PIN CYLINDER 10 Install Wire Cover Plate Install the wire cover plate to the inside of the door above the lock body Fig 9a Be careful not to pinch the wires when securing the cover plate Note Wire cover is only required for wood doors Inside Face of Door with the wire run channel on inside face of door 0 y Back Side of Wire 0 Cover Plate Harness from Lock Body Wire Cover SISSYH Door Status Switch e771 Xa 2 3 32 Diameter by 1 2 Deep Holes 2 6 x 1 2 Flat Head Security Torx Wood Screws CYL LOCKBODY Fig 9b Detail ig A Fig 9a This Side Down Copyright ae Corbin Russwin ne an ASSA ABLOY rou company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 11 ASSA ABLOY the global leader in door opening solutions CL33700 PWI PIP Series Cylindrical Lock Corbin 7 Russwin ASSA ABLOY 5 Installation Instructions Continued 11 Install optional Weatherseal Gasket For non fire rated door applications an optional gasket may be used as a weatherseal between the escutcheon and the outside door surface Peel off the adhesive backing on the gasket and install the gasket along the edge of the outside Access Gasket escutcheon assembly Fig 10 Gite Access Tim 12
9. in door opening solutions RgorbinZy Access 700 TCPWI1 TPIP ASSA ABLOY ASSA ABLOY is the global leader in door opening solutions dedicated to 8 A Copyright 2014 Corbin Russwin Inc an ASSA ABLOY Group company satisfying end user needs for security safety and convenience All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited
10. lt Push release tool Slide lever over Into release hole Lever catch Remove lever Pull on lever Make sure lever will not pull off RELEASE TOOL CYLINDER LEVER ROTATE KEY INSERT KEY AND ROTATE Rotate key 45 clockwise from shed position Push in release tool into Release hole remove lever Insert key and rotate 45 from Shed position slide lever on Make sure lever will not pull off Copyright 2014 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the 10 ASSA ABLOY the global leader in door opening solutions express written permission of Corbin Russwin Inc is prohibited CL33700 PWI PIP Series Cylindrical Lock Corbin 7a Russwin ASSA ABLOY 5 Installation Instructions Continued 9 Installation and Removal of Lever and Standard Cylinders continued Standard Cylinder Installation Make sure cylinder tailpiece is aligned in same direction as cylinder bible Slide cylinder all the way into the lever For 6 pin cylinder Fold retainer at hinge and press fit retainer halves together as shown For 7 pin cylinder Break retrainer at hinge and discard spacer section Also remove black cylinder spacer from inside of chassis follback for clearance FOLD RETAINER HALVES FOR 6 PIN CYLINDER Standard Cylinder Tailpieces REMOVE SPACER AND DISCARD HINGE ACTUAL Jey SHOWN 22 SPIN ta 7 PIN Dimensions are
11. ASSA ABLOY the global leader in door opening solutions CL33700 PWI PIP Series Cylindrical Lock Corbin 7a Russwin ASSA ABLOY 6 PIP PoE Installation Wiring Continued Frame Harness Installation Components and wire harness supplied by McKinney Suggested installation Supplied by CI Cut end ceiling side PoE harness B Splice Crimp Connector TIA EIB 568 B Standard Wiring cen wie a White Blue White Blue EE White Orange i Ceiling White Orange EH ee eRe eoecccccces White Green White Green 24AWG eren e Stranded White Brown 7 Drain White Brown EA Wietr E om fe oO Batt 5S Do not confuse pair numbers with pin numbers A pair number is 15 Frame or used for reference only eg 10BaseT Ethernet uses pairs 2 amp 3 The Harness a 3 pin numbers indicate actual physical locations on the plug and jack xe lo ke Hinge side of PoE harness Frame Side O 5 1 Feed cut end of harness into hole on hinge side through single access Harness ss hole Assembly 8 lt 15 length S 2 Push one of the connectors back through hole and feed into separate access hole Each of the hinge side harness connectors should end up threaded through a different access hole and matched to the same size pin con Cable drain wire WE nector from the door harness Canceled in e 4 pin male Molex connector shrink
12. ad magstripe card or key retracts latch e Inside lever retracts latch e BHMA Grade 1 UL Fire Listed Electrical Specifications e HID multiCLASS SE technology offers support for the following credentials e High Frequency 13 56 MHz e HIDiCLASS e HID iCLASS SE SIO enabled e HID iCLASS Seos e HID MIFARE SE e HID DESfire EV1 SE e MIFARE Classic e DESfire EV1 e FeliCa e Low Frequency 125 kHz e HID Prox e Magnetic Stripe e NFC enabled Mobile Phones Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening and Corbin Russwin Inc makes no representations or warranties concerning what such impact may be in any specific situation When retrofitting any portion of an existing fire rated opening or specifying and installing a new fire rated opening please consult with a code specialist or local code official Authority Having Jurisdiction to ensure compliance with all applicable codes and ratings Copyright 2014 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 3 ASSA ABLOY the global leader in door opening solutions CL33700 PWI PIP Series Cylindrical Lock Corbin 7 Russwin ASSA ABLOY 4 Product Illustration ITEM No DESCRIPTION 1 Outsi
13. atus d Push door status switch firmly into place by hand Mckinney Switch Electronic J ey Important DO NOT TAP SWITCH WITH ANY TOOL Transfer on v Hinge 4 if PoE ee Door Status CL33700 PWI PIP Switch Hole Fig 5a Series Lock Leper Patent Pending ae Vertical LHAT G of Strike Dim 2 See template Collar is used only with metal doors Horizonta of Strike A E Door Status Switch Strike for Cylindrical Lock Fig 5b 3 8 D 3 4 D Inside of Door Copyright 2014 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 8 ASSA ABLOY the global leader in door opening solutions CL33700 PWI PIP Series Cylindrical Lock Corbin 7a Russwin ASSA ABLOY 5 Installation Instructions Continued 6 Install Lock a Feed lock body and wires through 2 1 8 diameter hole from outside of door Fig 6a Q Q b Be sure latch engages lock body Fig 6b IMPORTANT Door must remain open during installation Use door stop Door Status Switch Fig 6b T Install Spring Cassette and Route Wires RKA cap a Plug harness into wire from lock body Fig 7a b Nz b Route lock body harness and ground wire Fig 7b Detail L c Install inside spring cassette and tighten using two 12 24 Fig 6a screws provided Fig
14. ccurate Pull Tab Fig 13 14 Inside Cover Installation a Secure cover with 2 security screws utilizing security allen wrench provided Security Allen Screw Fig 14 Copyright 2014 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 15 ASSA ABLOY the global leader in door opening solutions CL33700 PWI PIP Series Cylindrical Lock Corbin 7 Russwin ASSA ABLOY Important Note Wiring Installation If you are installing PIP PoE please go to Page 17 PIP Installation Wiring If you are installing PWI please go to Page 20 Operational Check Continue With Installation Copyright 2014 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 16 ASSA ABLOY the global leader in door opening solutions CL33700 PWI PIP Series Cylindrical Lock Corbin 7a Russwin ASSA ABLOY 6 PIP PoE Installation Wiring 17 PIP PoE Installation Wiring PoE Frame harness asse
15. dbolt for deadbolt functions e For units with cylinders the following checks apply Insert key into cylinder and rotate a There should be no friction against lock case wire harness or any other obstructions If friction or binding occurs read just cylinder and wiring harness to eliminate issues b The key should retract the latch and the key should rotate freely c The key should extend and retract the deadbolt e For units without a keypad add card using LCT software and test e For units with a keypad add pin and card using LCT software and test 2 LED signalling e After using a valid credential a green flash followed by three fast amber flashes indicates a low power condition Check the input voltage If the input voltage is low disconnect the lock from the power source and check the power source voltage If the power source voltage is correct inspect the lock wiring for a possible short e lf the lock loses power it will flash rapid amber for approximately one minute After that the lock will no longer be functional 3 When you have completed the tests close the door to ensure latchbolt and deadbolt fully extend into strike plate without binding Copyright 2014 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 20 ASSA ABLOY the global leader
16. de Escutcheon Assembly Mag Swipe Outside Escutcheon Assemby Mag Swipe and Keypad Outside Escutcheon Assemby Mag Swipe Keypad HID 125kHz Prox and 13 56 MHz Prox Outside Escutcheon Assemby Mag Swipe HID 125kHz Prox and 13 56 MHz Prox Outside Escutcheon Assemby Mag Swipe Keypad HID 125kHz Prox and 13 56 MHz Felica Outside Escutcheon Assemby Mag Swipe HID 125kHz Prox and 13 56 MHz Felica WiFi Controller Assembly PoE Controller Assembly Mounting Plate Assembly Inside Escutcheon Assembly with Privacy Button Copyright 2014 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 4 ASSA ABLOY the global leader in door opening solutions CL33700 PWI PIP Series Cylindrical Lock Corbin 7a Russwin ASSA ABLOY 4 Product Illustration Continued Tools Required e Phillips Screw Driver 2 3 e Flat Blade Screw Driver Standard size a e 1 8 Security Allen Wrench supplied Ny e 7 64 Allen Wrench supplied e T20 Security torx driver Supplied Oo 1 783F918 CL33134 Cylindrical lock with fixed core cylinder 783F928 CL33134 Cylindrical lock with removable core cylinder Inside Spring Cassette REX D134 O ae Inside Spring Cassette REX D214 3 Outside Spring Cassette 1 3 4 2 Door Outside Spring Cassette 2 2 1 4
17. e the 2 pin DPS connector b Secure the 10 pin lock body assembly connector NOTE Optional 2 pin external 9 24VDC power connector Board to Board Connector Tae ese eee CA EE FB ey Cw Ga A Wire Positioning Please follow these steps prior to installing inside escutcheon to prevent any damage caused by pinching wires c Tuck excess cable into wire hole on inside of door d Finish securing mounting plate and reader to door by fully tightening through bolts on inside of door Fig 10E e Secure the 24 pin card reader connector Copyright 2014 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited ASSA ABLOY the global leader in door opening solutions CL33700 PWI PIP Series Cylindrical Lock Corbin 7 Russwin ASSA ABLOY 5 Installation Instructions Continued a Insert bottom tab of controller into slot on mounting plate Fig 12a b b Looking down from top of controller ensure proper alignment of board to board connectors Fig 12b while pivoting controller toward door until two tabs on top snap securely into place on mounting plate Fig 12b CAUTION To avoid possible damage to boa
18. mbly PoE Door harness From McKinney From McKinney PoE data hinge Patent Pending Access 700 PIP PoE Lock From McKinney Order of installation may vary Refer to appropriate sections for instructions g DRI Certified Integrator Cl supplies and terminates Supplied by CI the B Splice connector and the Supplied by End User oo Male RJ45 connector from harness to Baid iea Splice i ili atch Cable ae aina onneen end user provided facility cable Bee paelo PoE Switch PoE Switch w To building or electrical ground PoE Switch Rack is 77 Terminated to RJ45 M RJ45 F Jack Cable CAT 5e or higher PoE Patch Panel Earth Ground Ceiling 24 AWG Drain Wire Terminated on Rack es ecococooo jolene ccoce pies eee PORES E OHHH HEE OEE EESOEEOEEHEEHESEHEOEEHE HEHEHE EEHEHEEEESEEHEEEHEEOESEEEEMELESEEEEE EEL ESE SEES EOES 24AWG N Stranded Drain Wire for aE Earth 9 5 Ground in os 15 Frame Er Harness oiie Approved Software 2S k P lt 15 Frame Side O 5 Harness z Assembly gx 15 length Al 5 Cable CAT 5e b 26 AWG stranded shielded 1000hm Cable drain E Se OLANG E wire con cealed in qf e Shrink tubing olex M Molex F Molex F Molex M O Ground Ring Terminal SY Secured to Lock Mounting Plate TIA EIA 568 B Standard Wiring COE O ZUTT COTR Mc MASSA ADLOY Group company All rights reserved Reproduction in whole or in part without the pies written permission of Corbin Russwin ihe is prohibited 17
19. ns 2 Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired opera tion Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruc tions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
20. rd to board connectors care should be taken when securing controller to mounting plate If there is resistance when securing detach controller to determine cause before re attaching controller Connectors Ai m 4 Ia o cH HAGBBEE Beer Fig 12b Detail Copyright 2014 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 14 ASSA ABLOY the global leader in door opening solutions CL33700 PWI PIP Series Cylindrical Lock Corbin 7a Russwin ASSA ABLOY 5 Installation Instructions Continued 13 Battery Installation Before installing batteries for the first time Remove pull tab from its position beneath the coin cell by pulling on tab in direction of arrows printed on tab Fig 13 a Place 6 AA alkaline batteries in the compartment being careful to align polarity properly b After batteries are installed there is a slight delay then an audible beep will sound and the lock motor will cycle For battery replacement When replacing the 6 AA alkaline batteries in the compartment please note batteries must be replaced within five 5 minutes to prevent the internal clock from becoming ina
21. tubing e 6 pin male Molex connector with ground wire Notes O e Connectors only go on one way They cannot be plugged to incorrect position e Do not force and do not offset connectors e Be sure they are completely seated flush 4 pin M 4 pin F Hinge side harness connectors e 4 pin male molex connector e 6 pin male molex connector with ground wire Lock side harness connectors e Ring terminal e 2 4 pin connectors 6 pinM 6 pin F Drain Wire Copyright 2014 Corbin Russwin Inc an ASSA ABLOY Group company Frame PoE Hinge Patent Pending All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 18 ASSA ABLOY the global leader in door opening solutions CL33700 PWI PIP Series Cylindrical Lock Corbin 7a Russwin ASSA ABLOY 6 PIP PoE Installation Wiring Continued Hinge Installation Order of installation may vary Refer to appropriate sections for instructions Hinge side harness connectors e 4 pin male Molex connector e 6 pin male Molex connector with ground wire Lock side harness connectors e Ring terminal e 2 4 pin connectors e 4 pin Molex connector e 4 pin connector Notes e Connectors go on only one way They cannot be plugged to incorrect position e Do not force and do not offset connectors e Be sure they are completely seated flush
22. y Prep Wood Door Preparation Copyright 2014 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 6 ASSA ABLOY the global leader in door opening solutions CL33700 PWI PIP Series Cylindrical Lock Corbin 7a Russwin ASSA ABLOY 5 Installation Instructions Continued 3 Install Latch Bolt Install using two 8 x 3 4 combination screws Fig 3 Note Make sure the beveled bolt is facing the strike 4 Install Strike Install using two 12 x 1 combination screws Fig 4 Centerline of Latch Front and Strike Optional Strike Box N 7 Copyright 2014 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited T ASSA ABLOY the global leader in door opening solutions CL33700 PWI PIP Series Cylindrical Lock Corbin 7a Russwin ASSA ABLOY 5 Installation Instructions Continued 5 Install Door Status Switch supplied with product a Drill 3 4 hole in frame for switch Fig 5a and 5b b Snap the sensor in place in the frame c Insert connector end of DPS harness through raceway on latch edge of door Fig 5c Note Use collar in METAL door only Door St
Download Pdf Manuals
Related Search