CYCLOPS PARALYSER 385 Specifications
Contents
1. e Option 15 enables the auto relock feature The doors will automatically re lock when the vehicle has been disarmed by remote control and the doors remain closed for more than 120 seconds e Option 17 is used to extend the time length of the central locking pulses Vehicles that use a pneumatic central locking system require about three seconds to allow the pump to charge the air hoses Enable this option only to extend the time in these situations Warning extending the pulse time to a direct drive relay will cause damage to actuator Option 19 is used to change the values of the Emergency PIN A card with the PIN details must be supplied by your installer Please contact your installer if the card is missing Option 21 the alarm system can be set to produce an open door warning when arming The warning is in the form of a short series of chirps from the siren or horn Do not enable this option where the dome light illumination is extended by the vehicle s timing circuit optional feature will require additional connection s B CHA NGING PIN CODE To alter the PIN code of the system follow the standard option change procedure select option 19 e The vehicle indicators will flash twice to inf orm you that the system is ready to accept the new PIN The time out is set to two seconds If the programming has not begun before then the system will drop out of programming mode e Enter the new digits by mom2. CY CL PS SECURITY SYSTEMS CYCLOPS SECURITY SYSTEMS THIS CARD SHOULD NOT BE LEFT IN YOUR VEHICLE II MUST BE KEPT IN A SAFE SECURE PLACE BREHYYYRRRERKEES e PIN Override Procedure Programmable Options Program Options Table e Options Descriptions e Changing PIN Code Battery Replacement Specifications Optional Features gt Central Locking Boot release gt Anti hijack e Electric window closer Trouble Shooting Warranty User Details 3 Contents Page Introduction 5 Operations e Remote controls gt Arming and Disarming gt Arm Disarm Siren Confirmation gt Silent Arming e Automatic Arming e Dome Light Function e Panic Feature e Open Door Warning gt Immobilisation gt Alarm Protection Zones e Diagnostics e Emergency Override nas 0000000144 4 CYCLOPS PARALYSER 385 ENGINE IMMOBILISER CycLOpS SECURITY SYSTEMS Introduction Congratulations on having one of the world s most advanced alarm and engine immobilisers installed in your vehicle The CYCLOPS P385 meets Australian Standards AS NZS 4601 6 AS NZS3749 The P385 uses high security high reliabilit y circuitry to disable your car s engine The alarm system uses sensors and independent switches to protect the entry points to the vehicle If a would be thief removes the battery leads from the battery terminals the system will continue to sound the siren using it s battery backup feature
3. OPERATIONS REMOTE CONTROLS The P385 is supplied with two rolling code remote controls Each time a button is pressed the code rolls to a new code Each code is never used twice A small green Light Emitting Diode LED will light when a remote control button is pressed ARMING AND DISARMING To arm or disarm the system press the main button on the remote control The vehicle s indicators will confirm a valid remote operation Two flashes for arm and one flash for disarm The status LED located on the car s dash or steering column will flash when the immobiliseris armed ARM DISA RM SIREN CONFIRMATION Each time the P385 is armed the siren will chirp twice to confirm the arm operation The siren will not chirp if the automatic arming function arms the system The siren will chirp once when the system is disarmed by remote control MAIN BUTTON SECONDARY BUTTON 26 SILENT ARMING The arm disarm confirmation chirps can be suspended for one operation by momentarily pressing the secondary button before pressing the main button The chirp will re enable upon the next operation The siren can be permanently cancelled by changing option 13 see page 11 AUTOMATICARMING The P385 will automatically disable the engine 40 seconds after the ignition switch is turned off Pressing the main remote control button after the system has automatically armed will command the P385 to disarm for another 40 seconds Switching the ig
4. listening for the sound of breaking glass For convertibles and softtop cars additional sensors can be installed to provide movement detection DIAGNOSTICS When any circuit triggers the P385 the number of the zone responsible will be recorded in the system memory The number is flashed back through the indicators and status LED when the P385 is next disarmed The zones are 4 Glass Breakage listed in the table EMERGENCY OVER RIDE If either of the remote controls supplied with the P385 is lost broken or stolen the immobiliser can be disarmed by use of a unique 4 digit Personal Identification Number PIN The PIN is entered using a combination of ignition switch and LED flashes see page 10 9 PIN OVER RIDE PROCEDURE To illustrate the PIN over ride procedure we will assume a PIN of 4 3 2 1 1 Turn the lock on the back of the siren to disable the sound 2 If indicators are still flashing allow the systemtoreset with all doors closed 3 Turn ignition switch to ON position the status LED will remain lit 4 Turn ignition switch to the ACC position and SWITCH SIREN OFF count the LED flashes 5 Turn ignition switch ON when the 4th flash has extinguished 6 Turn back to ACC position and count 3 flashes switch ignition ON 7 Turn back to ACC position and count 2 flashes switch ignition ON 8 Turn back to ACC position and count 1f lash switch ignition ON When all f our digits have been entered
5. the LED does not light up when the button is pressed then change the battery To dothis you will need a small screwdriver See page 12 for details on battery replacement WARRANTY The Dynamco range of Cyclops Security Systems is covered by an extensive two year warranty parts amp accessories one year In the unlikely event of a faulty system Dynamco will either replace or repair the system at no cost during the 2 year period The warranty does allow for the following conditions Subject to the conditions stated below Dynamco Pty Ltd warranty the product to be free from manufacturing defects and faulty material within the warranty period stated That the warranty registration has been completed in full at the time of purchase installation and is produced when warranty service is sought The warranty does not cover general maintenance such as cleaning adjusting of door boot bonnet or any entry point switch nor replacement of consumables items such as transmitter batteries lighting circuit bulbs switches The warranty shall be null amp void if ll Any person other than by an Authorised Cyclops Sales Service amp Installation Centre has repaired the product 2 Should a system part defect become apparent within the warranty period DYNAMCO PTY LTD will repair the product free of charge for parts and labour The warranty does not cover service labour content or mobile service content 3 The product has been altered or tampe
6. the car doors will lock Likewise when disarming by remote control the doors will unlock When the auto lock feature 15 is enabled the doors will re lock after 20 seconds if all doors remain closed after disarming 16 BOOT RELEASE Press the second button on the remote control and keep it depressed until the boot releases This will take about three seconds A successful boot release signal will disarm the alarm and flash the vehicle indicators four times This function can only operate if the vehicle is equipped with an electrical boot release ANTI HIJ ACK Two seconds after the ignition is switch to the ON position the P385 will lock the cars doors The lock signal will be cancelled if the P385 detects any connected door open As soon as the ignition switch is turned off the P385 will unlock the doors This feature comes as standard and can be disabled see option 3 ELECTRIC WINDOW CLOSER Only when the P385 is armed by remote control the electric windows of the car will roll up until closed PROBLEM SOLVING System won t arm LED on dash wont flash Make sure that ignition switch is in the OFF position Ensure the vehicle battery is not flat Try your spare remote transmitter unit System won t disarm LED on dash won t extinguish Try spare remote control Use Emergency PIN to override system and contact nearest Cyclops service centre The remote fails to operate If the remote fails to operate and
7. when the ignition is switched on except when a connected door is open The anti hijack feature unlocks the doors when the ignition is switched off when driver has reached destination The feature is disabled if the dome light illumination is extended by a vehicle timing circuit e Option 7 programming remote isn t strictly an optional feature This feature is used if a spare remote is purchased Carry out the same procedure as normal option changes The first flash indicates the system is ready to accept a new remote code Press the main button of the new remote control within two seconds to teach system Four indicator flashes indicates successful programming procedure e Option 9 illuminates the dome light of the vehicle for thirty seconds when the system disarmed The light will extinguish early if the ignition switch is turned to the ON position Installer may have disabled this function to prevent damage to system enquire before enabling e Option 1 determines whether the 30 seconds of siren output is constant or pulsed The constant output suits a connection to a siren which allows the siren to sound at full volume The pulsed out put suits the car horn optional feature will require additional connection s D PROGRA MMA BLE OPTION DESCRIPTIONS cont Option B sets the system to always arm disarm in silent mode The standard indicator flashes will accompany each arm disarm command but the siren will remain silent
8. correctly the car s indicators will flash once to confirm that the immobiliser is disarmed The engine can be started and the car driven The automatic arming feature will ensure car is secured again if the ignition is left off for more than 40 seconds 10 PROGRA MMA BLE OPTIONS The P385 includes 9 programmable options which alter the system functions to comply with the user s preferences and vehicle special needs Changing an option settingis as simple as e Switch the ignition key ON a certain number times this number corresponds tothe option number Press the remote control after the prompt from the vehicle s indicators After the remote press the indicators will flash either once or three times toshow the result of the option change Please seethe follow table PROGRA MMA BLE OPTIONS TABLE IGNITION SWITCH TURNS 1FLASH 3FLASHES 3 ANTI HIJ ACK DISABLED ENABLED 7 PROGRAM NEW REMOTE PRESS REMOTE 9 DOME LIGHT UPON DISA RM DISA BLE ENABLED u HORN SIREN OUTPUT TYPE PULSED CONSTANT B ARM DISA RM CONFIRMATION DISABLED ENABLED 5 120 SEC RELOCK DISABLED ENABLED C LOCKING PULSE TIME 0 8 SEC 3 SECS 19 CHANGE PIN CODE BEGIN NEW PIN 21 OPEN DOOR WARNING DISABLED ENABLED do not change installer only incorrect setting can damage the system or central locking 1L PROGRA MMA BLE OPTION DESCRIPTIONS e Option 3 the Anti Hijack feature locks the car doors
9. entarily pressing the main button on a valid remote control The vehicle indicators will flash in response to each press Stop pressing when the correct digit count is achieved Each digit will be confirmed by two indicator flashes e Enter the remaining digits in the same fashion Four flashes will confirm the programming procedure is complete Arm the system and confirm the new PIN by completing override procedure page 10 Ensure the new PIN is recorded but do not leave in vehicle BATTERY REPLACEMENT Using a flat head screwdriver to carefully separate the two body housings taking care not to disturb the circuit board Remove the old batteries whilst paying attention to the orientation of the positive and negative terminals Insert new batteries in identical fashion to the original and re assemble REMOVE BATTERIES remote Test remote control by sia aaa pressing main button For further information please contact your local Cyclops service centre Remote battery type CR2016 CASE TOP MEMBRANE CASE BOTTOM SPECIFICATIONS Model Number 386 ____________ less than 20mA while armed Country of manufacture China in Dynamco s ISO 9002 facility RF Transmission Freq 433MHz 0 OPTIONAL FEATURES All optional features require additional connections Many require additional hardware as well Each feature is described within the next pages CENTRAL LOCKING Each time the P385 is armed by remote control
10. nition switch to the ON position is the only way to stop reset the auto arming countdown DOME LIGHT FUNCTION When the P385 is disarmed by remote control the internal circuitry will switch on the car s dome light for 30 seconds This feature will be cancelled if the driver turns the ignition switch to the ON position Factory setting is disabled see page 11 or details 27 PANIC FEATURE Car Location The P385 can be commanded panic for 30 seconds if the main button is pressed for more than 2 seconds The panic feature will sound the siren and flash the indicators To cancel the Panic Feature momentarily press the main button once more The panic feature is available only while the systemis armed OPEN DOOR WA RNING If any connected door is detected as being open while arming the P385 will flash the indicators and chirp the siren 8 times This can happen if the car has a built in feature which extends the dome light time These cars will need this feature disabled option 21 see page 1 IMMOBILISATION The P385 includes two independent circuits of immobilisation Each circuit starves the engine of one of it s critical power supplies The circuits are designed to be fail secure so if a would be thief was to cut power to the P385 the circuit design will ensure the car remains immobilised 8 ALA RM PROTECTION ZONES The P385 protects the vehicle by monitoring all door bonnet and boot switches as well as
11. red with in any way or the serial number altered defaced orremoved 4 The defect has been caused by negligence by the owner or their agent third party S The product has not been operated correctly installed by an unauthorised Cyclops installer or has been subjected to misuse or undue wear and tear 6 Siren control module remote controls or any other system part are damaged by water The warranty does not cover the following costs 1 Transport of the product to and from Cyclops Service Centres 2 Insurance of the product whilst in transit to or from the Cyclops Service Centres 3 Cost of any service call labour where the product is found by Cyclops to be in good working order The benefits conferred by this Warranty are in addition to all other rights and remedies which the consumer has conferred in law No liability is accepted for any loss loss from damage to or inability to use the vehicle to which the system is installed 18 WARRANTY REGISTRATION PURCHASED FROM OWNER S NAME TYPE OF VEHICLE VEHICLE REGO MODEL OF UNIT P I N DATE OF MANUFACTURE DATE OF INSTALL WARRANTY PERIOD CONTROL MODULE SIREN amp REMOTES INSTA LLER S NAME AFTER HOURS EMERGENCY PHONE 20
Download Pdf Manuals
Related Search