BionX S-series Owner`s manual
Contents
1. 0 2 Lu NOTICE For these bicycles third party insurance is mandatory In most countries wearing a helmet is not mandatory However we strongly recommend to always wear a helmet for your own safety Since 40 km h electric bicycles are legally considered to be lightweight mopeds they do have a throttle which allows riding them up to 20 km h using motor power only This means that up to 20 km h your bike can be used as an E Bike rather than as a Pedelec Above that speed the motor will assist pedaling up to a speed of 40 km h NOTICE The maximum power of the motor on your bicycle is limited to 250 W Your 40 km h electric bicycle is still a bicycle It is therefore not recommended that you use it as a moped or an E bike without pedaling Using battery power only will strongly limit your range 3 2 Differences in equipment The technical equipment of these 40 km h bikes is almost identical to that on Pedelecs The following parts are additional and or different Rear view mirror Insurance plate holder Throttle on the controller Extra reflectors Slightly different brake levers Type approval plate on the frame NOTICE These are all part of the type approval It is not allowed to remove or exchange them for other non certified equipment This also applies to the handlebars tires seat post headlight rear light brakes kickstand and controller 3 3 Instructions for use Riding is the same as2. Do not ride the electric bike without the battery pack The battery pack must be on the bike while riding else the bike has no lights when needed Do not misuse the electric bike by riding it without a saddle Some bikes have a quick release on the seat post If the saddle gets stolen it may lead to hazardous situations when still riding on the electric bike without a saddle Check your bike for normal operation loose parts and defects before riding If you find any problem visit your bike dealer for repairs before riding De aware that other road users do not expect that an electric bike can ride faster than a normal bike Riding faster also increases the risk of accidents Do not ride abusively Only ride in the Use Conditions specified for your bike Please refer to Trek s Bicycle Owner s manual for more detailed information Do not over load the rear rack The maximum allowable weight for the rear rack on RIDE bikes is 20 kg for bikes with a rear rack battery pack and 25 kg for bikes with a down tube battery 3 The electric system of your new bicycle needs special attention Do not clean your electric bicycle with a high pressure washer Any electric system is sensitive for moisture High pressure water might ingress in connectors or other parts of the electric system Protect the battery docking connector With removed battery pack apply the protective cover to prevent corrosion and damage to the connector H
3. To switch the system Off press the 5 button The battery pack will beep five times Riding with the system On in level ON 24 HB se 11 is the same as riding with the system Off If the bike is left boss tnr 3 with the system On it will automatically switch Off after un about 10 minutes B a Changing the position of the buttons Normally the On Off button 5 and the mode switch Q 4 n 115 button are on the right and the and buttons on the left en nr The functionality of the u can be swapped right to left Uum The code to access this is 2009 More information about B uis nt programming via the controller can be found later in this manual a Assistance When the motor provides power the bicycle isin assistance g Ji T p mode There are four levels of assistance The level of i 5 EM an assistance is shown by the bar graph on the right below the 7 digits for speed The narrow graph on the display shows the amount of energy delivered to the motor SOME To increase assistance press button For assistance level 1 press once Press again for more EN 15 INSTRUCTIONS FOR USE assistance For less assistance press button When there is no assistance level shown and the bicycle icon is visible on the screen there is no assistance Pedaling is then the same as on a normal bicycle To switch from any level of regeneration
4. light Off will appear on the screen fe j NIC FA er NOIR U GIOI Y FOK VE e Mountain mode The Mountain Mode allows for longer uphill riding before the motor shows power reduction due to so called temperature derating As Mountain Mode limits the maximum motor torque the motor will stay cooler for a longer period of time Select this option by going to assistance level 4 and then press and hold the button for 2 seconds To return to assistance level 4 press the button once Changing the language option of the controller The RIDE Pro controller allows you to change the language that is displayed on the screen See the part programming later in this manual to set the correct language EIS o 0 2 Lu Removing and installing the RIDE Pro controller To remove the RIDE Pro controller from the bike press the catch of the holder and slide the controller off towards the rear To install the RIDE Pro controller onto the handlebar align the controller with its clamp and slide the controller forward until it clicks NOTICE To prevent loss of riding information please make sure that the controller is switched Off before it is removed from the bike Unintended removal of controller out of its dock If the controller is moved off its clamp while the system is active On the system will no longer assist even when the controller is replaced into its
5. 4 20096 Flat terrrain 55 90 km 50 70 km 45 55 km 30 40 km Hilly terrrain 45 5 km 35 60 km 30 45 km 20 30 km Mountainous terrrain 30 45 krn 30 45 km 20 30 km 15 25 km Range for a fully charged RIDE R420 or RIDE C420 battery pack Terrain Assistance level 1 25 2 50 3 100 4 200 Flat terrrain 80 125 km 60 100 km 55 80 km 40 55 km Hilly terrrain 65 100 km 45 85 km 35 65 km 25 40 km Mountainous terrrain 45 65 km 35 60 km 25 40 km 20 35 km e Transporting an electric bike Because a RIDE bike is heavier than anormal bicycle due to the additional drive components and because of the presence of a Li ion battery pack please take care of the following when transporting the electric bike a Take care about the maximum load capacity on the towbar of the vehicle when placing a bike carrier on it with multiple bicycles including an E bike Please refer to the manual of the towbar and or the vehicle for additional information b Take care about the maximum load capacity of the car s roof when placing a bike carrier on it with multiple bicycles including an E bike Please refer to the manual of the vehicle and or bike carrier for additional information C A bike carrier has a limited load capacity Sometimes that is not enough to carry an heavier electrical bicycle in combination with other e g electrical bicycles Please refer to the manual of the bicycle carrier for more detailed information d Remove the battery
6. potentially catch fire In an emergency situation fully immerse the battery pack a large container of water Storage of the battery pack When the battery pack is not in use store it in a dry cool place Li lon batteries are best stored at a 100 charge The temperature should be between 5 C and 25 C preferably 5 10 C Do not store it in places where temperatures get higher than 25 C or lower than 5 C Keep away from extreme temperature changes Keep the battery pack from condensation to prevent corrosion forming on the terminals Failure to follow these instructions result in damage to your battery and may require battery replacement The battery pack can be stored for up to one year before a recharge is necessary provided it was 10096 charged first We however recommend to charge it once every six months when not in use NOTICE It will need waking up out of deep sleep if it has not been used for a longer period of time To wake it up it suffices to connect the power supply to the battery pack and a wall socket This will directly activate the battery pack again for normal use When the battery pack is not in use we recommend to charge it at least once every six months EN 25 Tip The battery packs with the round charging connector can be left connected to the power indefinitely The power supply electronics will take care of the correct charging procedure However you will save energy by disconnecting t
7. remedy of the warranty This warranty extends from the date of purchase applies only to the original owner and is not transferable Trek Bicycle Corporation is not responsible for incidental or consequential damages Some states do not allow the exclusion of incidental or consequential damages so the above exclusion may not apply to you Claims under this warranty must be made through an authorized Trek dealer Proof of purchase is required The subject item must be registered with Trek Bicycle Corporation either through on line registration or by the receipt of a warranty registration card by Trek Bicycle Corporation before a warranty claim may be processed Warranty duration and detail may differ by frame type and or by country This warranty gives the consumer specific legal rights and those rights may vary from place to place This warranty does not affect the statutory rights of the consumer 9 Contact Addresses and telephone numbers Trek Benelux Bikeurope B V Basicweg 12a NL 3821 BR Amersfoort The Netherlands Telephone 31 0 33 450 90 60 Internet www trekbikes com Diamant Trek Fahrrad GmbH Stettbachstrasse 2 CH 8600 D bendorf Switzerland Telephone for Germany 0180 350 70 10 Telephone for Austria 0820 820 121 Internet www diamantrad com Villiger Trek Fahrrad GmbH Stettbachstrasse 2 CH 8600 D bendorf Switzerland Telephone 41 0 44 824 85 00 Internet www villigerbikes ch For Service and Warr
8. 100 Yes 4 200 200 Yes Steep descent EN 12 m I EN 13 BONTRAGER SATELLITE ELITE FORKLIGHT l BONTRAGER 2 3 Bontrager Satellite Elite ForkLight The Bontrager Satellite Elite ForkLight comes in a RIDE and non RIDE version The RIDE version can be operated via the controller on the handlebar The energy that is needed to power the RIDE lights comes from the battery pack Both lights always work simultaneously Depending on model Adjusting the beams The height of the beams can be adjusted by turning knobs on both sides of the fork Both beams can be adjusted independently by turning knob A with a cross headed screwdriver Both beams at the same angle gives the best performance l BONTRAGER Fast ELectric Bike 3 40 km h Fast Electric Bike The 40 km h fast electric bike is an electric bicycle of which the assistance does not stop at 25 km h but at 40 km h This higher assist speed makes it the perfect electric bicycle for people who like riding faster than 25 km h Note though that the actual maximum speed that you can reach depends first and foremost on how strongly you pedal NOTICE Fast E bicycles are only available in Germany Austria and Switzerland 3 1 Legal rules Legally the 40 km h fast electric bike is no longer considered being a bicycle but a lightweight moped It has type approval as such SE o
9. from the bicycle and store them elsewhere in the vehicle during the drive Always respect local laws about transportation of a n electric bicycle Because Li lon battery packs of this size and power are considered Dangerous goods class 9 when transporting regulations may restrict the transport of separate Li lon batteries in some places The restrictions apply to most airlines and some trucking companies But if you intend to ship or travel with your complete RIDE bike with installed battery pack the regulations are less strict Make sure to check ahead with your airline or carrier before booking your trip if SE o 0 2 Lu it is allowed to travel with your complete RIDE bike 6 Visit your dealer on a regular basis for maintenance of your new bike Your dealer has the right knowledge and equipment to maintain your RIDE bike f you have questions about your new RIDE bicycle ask your dealer Getting the most from your RIDE Bicycle EN 2 m 2 m EN 3 CONTENTS Contents Important to read before the first ride Congratulations on your new electric bicycle 1 Quick start 11 BionX G2 controller 1 2 Pro controller 13 Charging 1 4 Rear rack battery packs 15 Downtube battery pack 2 Description 21 Specific parts for the electric bicycle 2 2 Assistance Regeneration 2 3 Bontrager Satellite Elite ForkLight 3 40 km h Fast Electric Bike 31 Legalrules 3 2 Di
10. 420 battery pack down tube type containing 52 Li Mn Li Ion cells 48 V 8 8 Ah max 423 Wh Motor configurations 1 250 W RIDE Rear motor derailleur and Roller Brakes 2 250 W RIDE Rear motor derailleur and disc brakes or rim brakes Magura or V brakes 3 250 W RIDE Rear SL motor lightweight derailleur and Roller Brakes 4 250 W RIDE Rear SL motor lightweight derailleur and disc brakes or rim brakes Magura or V brakes 5 250 W RIDE Front motor Internal gear hub and Roller Brakes 6 250 W RIDE Front motor Internal gear hub and rim brakes Magura or V brakes EN 10 31D5 IP RIPTION e Controllers 1 BionX G2 controller Controls all functions On Off the four assist levels the four regenerative levels and lights On Off It also functions as a bicycle computer measuring speed and distance and shows the battery charge level 2 RIDE Pro controller Controls all functions On Off the four assist levels the four regenerative levels and lights On Off It also functions as a bicycle computer measuring speed and distance and shows the battery charge level All the information can be provided in different languages m see programming e Brake Switch The right hand brake lever of cable activated brakes contains a switch that cuts off the power to the motor and switches the motor to generation mode as soon as the right hand brake lever is pulled a Wirin
11. N 17 2HE uium ggg umi EN QN NA 4 2 RIDE Pro controller 1 Speed indication 2 Battery charge level 3 button 4 Distance Odometer Chronometer Average speed Clock 5 button 6 Current assistance level 7 Current generation level 8 Mode switch Q button 9 On Off 5 button 10 Light indicator On or Off 11 Service Indication 4 Tr d WARNING If the Service Indication a steady or blinking wrench symbol is visible on the display refer immediately to paragraph 7 1 for instructions Switching system On Off Press any of the two top buttons briefly to switch the system On The battery pack will beep four times the system will perform a short self check shown on the display as a countdown in the speed field and the system will activate switch to On As soon as the system is On the screen will display and each function will be shown next to its corresponding button To switch the system Off press the 5 button The battery pack will beep five times Riding with the system On in level O is the same as riding with the system Off If the bike is left with the system on it will automatically switch Off after about 10 minutes e Changing the position of the buttons Normally the On Off button the mode switch button are on the right and the and buttons on the left The functionality of the buttons can
12. OWNER S MANUAL Electric Bicycle powered by BionX Diamant WV TREK VILLIGER A IT IS IMPORTANT TO READ THE WARNINGS AND INSTRUCTIONS IN THIS MANUAL BEFORE RIDING YOUR NEW BICYCLE ENGLISH This Electric bicycle manual is additional to the manual provided with your bicycle It treats those aspects in which the Electric bicycle differs from the non electric bikes 2013 Trek Bicycle Corporation All rights reserved No texts details or illustrations from this Manual may be reproduced or distributed or become the subject of unauthorized use for commercial purposes Additional manuals for using the Electric bicycle may be ordered as separate items from Trek Bicycle Should you discover any errors we would be grateful if you would bring them to our attention 1 o Z Lu IMPORTANT TO READ BEFORE THE FIRST RIDE The most important points for you to do 1 Even if you have ridden a bicycle for years it is important for every person to read the Bike Owner s manual and the specific RIDE Owner s manual carefully before you ride on the new RIDE bicycle Both manuals contains detailed information and useful suggestions about your new bicycle Make sure that you understand the proper use maintenance and disposal of the components of the electrical system of your new RIDE bicycle m 2 Think about safety Your safety and that of other road users is very important
13. RNING It is strongly advised to ride away ina straight line when an assistance level is selected Never select assistance level 3 or 4 during maneuvering or riding away ina tight corner The powerful reaction of motor might take you unawares Switching lights On Off Press the b button for 2 seconds to switch On Off the display light and if present the front and rear lights See time average speed odometer trip distance Use the Q button to change ccomputer functions Order of 24 T RAM Bes t day To prevent loss of riding information please make sure Ol Noose tian that the system is switched Off before the controller is removed from the bike appearance trip distance odometer average speed time of e Using the remote Some bikes have the controller positioned on a middle clamp which means that the controller can more easily be operated with a remote This device can be used to select a higher or lower assist or regeneration level without removing your hands off the handlebars The red throttle button on the BionX remote is a convenient help to move the bike without pedaling up to 4 km h walking next to the E bike A WARNING Beware of unintended use of the throttle button when the system is switched On Quick START RIDE PRO CONTROLLER SE o 0 2 Lu Switching system On Off Push any of the two upper buttons briefly to switch the system On Push the 5 button to
14. andle your battery pack with care Do not drop or impact the battery pack Mishandling of the battery pack could lead to severe damage or over heating In an extremely rare case a battery pack that has been severely impacted or otherwise mishandled could potentially catch fire If you suspect damage to your battery pack visit your dealer immediately for inspection 4 Maintain the battery pack as instructed in the RIDE Owner s manual Failure to follow these instructions may result in damage to your battery pack and may require battery pack replacement Charge the battery pack at least once every six months or when the battery pack shows a low charge on the controller a low level red LED indicator or beeps every 30 minutes Only charge the battery pack with the included BionX charger When the battery pack is not in use store it with a 10096 charge in a dry cool place between 5 C and 25 C preferably 5 10 C Do not store it in places where temperatures get higher than 25 C or lower than 5 C Avoid extreme temperature changes EN 1 IMPORTANT TO READ BEFORE THE FIRST RIDE 5 Be careful when transporting a RIDE bike An E bike is heavier than a normal bike If transporting on a vehicle be aware of the maximum load capacity of the vehicle s roof towing hook and or of the applied bike carrier Refer to the manual of the vehicle and bike carrier for details Remove the controller battery pack and if present panniers
15. anty please contact your local dealer Part number 321466 Rev D September 2013 Fourth Edition CONTACT EN 36 EIS o 0 Lu Part nr 321466 Rev D
16. as it was earlier On a bike with a rear motor have the rear axle nuts tightened to the correct torque 40 Nm On a bike with a front motor have the front as well as the rear axle nuts tightened to the correct torque 40 Nm e The system does assist but irregularly On a bike with a rear motor have the rear axle nuts tightened to the correct torque 40 Nm On a bike with a front motor have the front as well as the rear axle nuts tightened to the correct torque 40 Nm Check all connections of the system System switches On as battery pack is put into the docking station This happens sometimes due to static electricity There is no problem with the system 7 2 Charging problems a The display does not show full after a complete recharge Please make sure you are following all charging instructions Let the battery pack cool down for several hours and try again If the problem persists fully discharge by riding and recharge the battery pack if necessary have your dealer update it to the latest firmware a The charging light does not turn red after connecting the power cable to the power source Check the power cable to the power supply If defective replace the cable immediately A WARNING Replace a damaged power cable immediately to prevent an electric shock PROBLEM SOLVING e The charging light turns green after only 10 minutes of charging Please make sure the system is turned Off before you connect the power supply
17. at the bolt for the brake arm is securely tightened 8 Check ifthe front brake works 9 Reconnect the motor connectors 10 Put the battery pack back onto the bike 11 Activate the system 12 Perform a short test ride to make sure that the system works WARNING Switch the system Off before you disconnect or connect the connectors of the motor You may experience strong sparking and possibly electric shock if you fail to do so a Removal refitting of the rear wheel No specific instructions are valid to remove the rear wheel When refitting the rear wheel 1 Ensure to align the axle with the frame NOTICE On bikes without a derailleur the chain may not be adjusted too tight measured at the most tight point in the chain else the RIDE system does not work properly and can the rider lose control of the bike while riding Adjust the chain so that there is 10 20 mm of slackness in 10 20 the chain at its tightest spot when a force of about 100 g is applied 2 Tighten the wheel nuts equally and evenly to a torque of 40 Nm Otherwise the system might not work properly If you do not have access to a torque wrench you can use a normal wrench but have your dealer checked the tightening torque of the nuts at the earliest opportunity 3 Afterwards perform a short test ride to make sure that the system works 6 Technical description 6 1 Bike specifics Motor Maximum continuous power output Maximum as
18. be swapped right to left 248 mus p gt _ programming via the controller can be found later in this manual 7 The code to access this is 2009 More information about Assistance When the motor provides power the bicycle is in assistance mode There are four levels of assistance The level of assistance is shown by the arrows at the bottom of the display A WARNING It is strongly advised to ride away ina straight line when an assistance level is selected Never select assistance level 3 or 4 during maneuvering or riding away in a tight corner The powerful reaction of motor might take you unawares To increase assistance press button For assistance level 1 c 19 km h press once Press again for more assistance For less assistance press button When there is no assistance level shown there is gt _ gt no assistance so riding is the same as pedaling a normal bicycle EIS o 0 2 Lu m 2 m c EN 19 a Regeneration When the bicycle regenerates electricity for the battery the system is in generation mode There are four levels of regeneration The level of regeneration is shown by the arrows at the bottom of the screen To increase the regeneration level press button For regenerative level 1 press once Press again to increase the regeneration level to a higher level For a l
19. best left to your dealer If you are forced to do it yourself follow the instructions Removal of the rear wheel 1 Make sure that the system is switched Off 2 Change to the highest gear 3 Remove the battery pack from its docking station 4 Unplug the connectors of the motor at the left hand side of the hub Make sure that both cables are unplugged see photo 5 Disconnect the rear brake V brakes Magura brakes release the rear brake Roller Brakes unhook the cable and housing stop from the brake Undo the reaction arm bolt 6 Loosen and remove the axle nuts N Slide the wheel forward in the dropouts until the wheel can be removed 8 Remove the chain from the sprocket and remove the wheel e Refitting the rear wheel 1 Make sure that the system is switched Off 2 Rollerbrake bikes make sure that the distance piece that centers the roller brake onto the hub is correctly in place 3 Make sure that the flat portion on the left hand side of the axle aligns with the left hand side dropout 4 Make sure the groove in the rear axle is facing up 12 o clock position Put the chain on the smallest rear sprocket and slide the rear wheel into the dropouts Make sure that the axle moves all the way back into the dropouts 5 Tighten the rear wheel nuts equally and evenly to a torque of 40 Nm Otherwise the system might not work properly If you do not have access to a torque wrench you can use a no
20. cage can be mounted on the adapter Only use the 4 bolts that are delivered with the holder to prevent damage to the battery cells inside E Removing the battery pack Put the key in the lock twist the key clockwise until the lock springs out step 1 2 see next page When the lock springs out the lever of the battery pack will be released Now take the key from the lock and pull the lever of the battery pack so that it slides upwards parallel to the down tube until it releases from the rail step 3 When the battery pack is not on the bike always use the protective cover on the contacts on the frame to protect the electrical system from water step 5 Be sure to fasten the cord of the protective cover in a safe way to the frame m Contacts at the bottom side of the down tube a Replacing battery pack Position the battery pack over the down tube with some space between the seat tube and the lower end of the battery pack step 1 below Now slide the battery pack down onto the rail 2 Use the lever to lower the battery pack carefully during the last phase of sliding so that the connectors engage 3 Be sure that the connector at the bottom of the battery pack and the connector on the docking engage properly When the battery pack is fully in place push the lock in until it clicks 4 Do not ride the bike with the lock open EN 23 4 5 Lighting The front and rear lights as well as the display li
21. clamp Please select the correct level of assistance again to reactivate the system Using the RIDE Link Most bikes with the RIDE Pro controller are equipped or can be equipped with the RIDE Link This device is mounted either the right or left side of the handlebar and can be used to regulate the following functions without moving your hands off the handlebar 9 1 em button Switch light On Off 2 button Increase assist level or decrease regeneration level 3 button Decrease assist level or increase regeneration level 4 Throttle button For Pedelecs walk assist up to 3 or 6 km h pedaling not needed For fast E bikes assist up to 25 km h pedaling not needed The red throttle button on the RIDE Link remote is a convenient help to move the bike without pedaling up to 4 km h walking next to the E bike A WARNING Beware of unintended use of the throttle button when the system is switched On EN 20 INSTRUCTIONS FOR USE 4 3 Rear rack battery packs e Battery pack size Depending on the model your bike will be equipped with either a RIDE R250 2 RIDE R320 or a RIDE R420 battery pack Removal charging and putting back are the same for all battery packs RIDE R250 2 battery pack containing 30 Li Mn Lithium lon cells 37 V 6 6 Ah max 244 Wh RIDE R320 battery pack containing 39 Li Mn Lithium lon cells 48 V 6 6 Ah max 317 Wh RIDE R420 battery pack co
22. e the controller is removed from the bike a Unintended removal of controller out of its dock If the controller is moved off its clamp while the system is active On the system will no longer assist even when the controller is replaced into its clamp Please select the correct level of assistance again to reactivate the system a Using the BionX remote Most bikes with the BionX G2 controller positioned on the middle clamp are equipped or can be equipped with the BionX remote This device is mounted either the right or left side of the handlebar and can be used to regulate the following functions without moving your hands off the handlebar 1 button Increase assist level or decrease regeneration level 2 button Decrease assist level or increase regeneration level 3 Throttle button For Pedelecs walk assist up to 3 or 6 km h pedaling not needed For fast E bikes assist up to 25 km h pedaling not needed Installation of the BionX remote for non equipped bikes To connect the BionX remote to the system the remote connector can be plugged into the receiver connector of the controller docking After that the brake generator connector can be plugged into the remote connector The red throttle button on the BionX remote is a convenient help to move the bike without pedaling up to 4 km h walking next to the E bike A WARNING Beware of unintended use of the throttle button when the system is switched On E
23. ear rack on the RIDE bike can be found on the rack stay and or the rear rack The maximum allowable load on the rear rack is 20 kg for bikes with a rear rack battery pack and 25 kg for bikes with a downtube battery pack a Getting the most from your electric bicycle Riding with the system on in level is the same as riding with the system Off With the system switched on your speed and distance will be measured and you will be able to use the lights This will not be possible when the system is Off The system will be most efficient when you pedal with a cadence of around 60 rpm Use the assistance levels according to your needs Always remember that your electric bicycle is still a bicycle and should be used as such The tables below provide approximate distances you can expect to travel on one battery charge based on ideal conditions Actual distances will vary depending on wind tire pressure rider weight riding style road conditions software settings topography age of battery pack and other parameters EN 26 m 0 Range for a fully charged RIDE R250 2 battery pack Terrain Assistance level 1 25 2 5096 3 100 4 200 Flat terrrain 50 80 km 40 65 km 30 50 km 25 35 km Hilly terrrain 40 70 km 30 55 km 20 40 km 15 25 km Mountainousterrrain 25 40 km 20 38 kn 15 25 km 10 20 km Range for a fully charged RIDE R320 battery pack Terrain Assistance level 1 25 2 5096 3 100
24. eur Roller Brakes Derailleur Rim Magura V brakes or disc brakes Internal gear hub Roller Brakes Internal gear hub Rim Magura V brakes or disc brakes The electric bicycle differs only slightly from a non electric bike The following parts are specific to an electric bicycle he battery pack in the rear rack or on the down tube he motor in the rear or front wheel hub The controller on the handlebars or on the clamp in front of the handlebars EN 4 m I EN 5 Quick START BIONX G2 CONTROLLER 1 Quick start This manual has all the information that you ll need to get the best from your electric bicycle We strongly recommend that you read it through However for quick use of the bike please read the Quick Start guide for the type of controller and battery pack on your bicycle 1 1 BionX G2 controller Switching system On Off Push any of the two upper buttons briefly to switch the system On Push the 5 button to switch the system Off When switched On the bike is in cycle mode zero assist e Assistance Regeneration Level Push the button once for assistance level 1 again for LIB higher levels Push the button to go to a lower level Onn bt E Arm Regeneration levels can be controlled in a similar way Push the button once for regeneration level 1 again for a DIS higher level Push the button to reduce regeneration A WA
25. fferences in equipment 3 3 Instructions for use 4 Instructions for Use 4 1 BionX G2 controller 4 2 RIDE Pro controller 4 3 Rear rack battery packs 4 4 Downtube battery pack 4 5 Lighting 4 6 Charging the battery pack 4 7 Battery pack care 4 8 Warnings and Suggestions for use 4 9 Programming 5 Maintenance 51 Cleaning 5 2 Removal and refitting of wheels for bikes with a rear wheel motor 5 3 Removal and refitting of wheels for bikes with a front wheel motor 6 Technical description 6 1 Bike specifics 6 2 Battery packs 6 3 Minimum and maximum temperatures for battery pack 6 4 Power supply 6 5 Compliance 7 Problem solving 71 Drive problems 7 2 Charging problems 7 3 Display problems 8 Limited warranty 9 Contact CONGRATULATIONS Congratulations on your new electric bicycle Your electric bicycle is a bike with electric pedal assistance This means that you can pedal it as anormal bike or that the bike can assist you in your pedaling The electric bicycle will assist you when you are pedaling The amount of assistance depends on the force you exert on the pedals SE o 0 2 Lu RIDE bicycles come in two classes Pedelecs and Fast Electric Bikes Pedelecs assist up to a speed of 25 km h This class is legally considered a bicycle Fast Electric Bikes assist at higher speeds This class is legally considered a lightweight moped This manual covers the following bikes both pedelecs and fast class Deraill
26. g Harness The wiring harness links controller brake switch battery pack and motor It runs through the frame and is linked to the battery pack via the docking station in the rear rack or via the docking station on the down tube EN 11 ASSISTANCE REGENERATION 2 2 Assistance Regeneration The system has four levels of assistance When the system is set to assistance the electric motor drives the rear or front wheel and assists you in your pedaling Additionally the system has four levels of regeneration When the system is set to regeneration the electric motor is used as a dynamo and generates electricity for charging the battery pack Going downhill you can reduce your speed by regulating the amount level of regeneration as the created resistance acts as a motor brake SE o 0 2 Lu A CAUTION Though that generation mode is not a substitute for using brakes to control speed or stop The tables below give an indication of the effort that is compensated in the different assistance and regeneration levels The real percentages of compensated effort depend on the software settings of the bike Effort Compensation with Batt R320 R420 and C420 Regenerative Very steep descent braking braking Effort Compensation Effort Assistance Compensation with Batt R250 2 Recharge WN lt Effort Regeneration an with Batt R320 Recharge R420 and C420 1 25 25 Yes 2 50 50 Yes 3 100
27. ght are switched On and Off on the RIDE controller When the battery pack shows empty there is still enough capacity left to run the lights for about two hours The onboard software ensures that as long as the bike is moving the lights can operate for an indefinite period of time using the dynamo function of the motor as the power source AA WARNING Do not ride the electric bike without the battery pack The battery pack must be on the bike while riding else the bike has no lights when needed SE o 0 2 Lu 4 6 Charging the battery pack WARNING Before charging make sure that the system is switched Off and never turn the system On or Off during charging This prevents unintended activation of the system Only use the power supply approved for use with this bike Charging with a non original power supply may cause the battery pack to overheat catch fire or even explode When charging do not let the battery pack or power supply get wet because of risk of electrical shock The battery pack can both be charged in the bike or it can be removed from the bike for charging Li lon batteries such as are used in the electric bicycle have no memory effect This means that the battery capacity is not influenced if the battery pack is recharged before it is completely empty You can recharge after every ride However you will get the most from your battery pack if for the first three charges you use it unti
28. he power supply when the light in the charging port has turned green The warranty does not cover improper follow up of battery care instructions e Battery pack recycling 5 Because a battery pack contains certain harmful substances it must be treated as chemical waste may not be disposed as normal waste NOTICE A battery pack may not be disposed as normal waste to prevent environmental ee pollution a defective or end of life battery pack can be handed over to your dealer or to another waste disposal according to local rules 4 8 Warnings and Suggestions for use e Think about Safety a Do not ride the electric bike without the battery pack The battery pack must be on the bike while riding else the bike has no lights when needed b Do not misuse the electric bike by riding it without a saddle Some bikes have a quick release on the seat post If the saddle gets stolen it may lead to hazardous situations when still riding on the electric bike without a saddle c Check your bike for normal operation loose parts and defects before riding d Be aware that other road users do not expect that an electric bike can ride faster than a normal bike Riding faster also increases the risk of accidents e Do not ride abusively Only ride in the use conditions specified for an electric bike An electric bike is meant to be used on paved roads or bicycle paths e Maximum load rear rack The maximum load for the r
29. hour of charging the battery pack will already be charged up to 80 of its capacity m 0 I The battery packs with the round charging connector can be left connected to the power indefinitely The power supply electronics will take care of the correct charging procedure However you will save energy by disconnecting the power supply when the light in the charging port has turned green NOTICE Since the computer inside the battery pack saves the system mileage and settings we discourage the use of a second battery pack A second power supply would be a better solution The battery pack is very durable The capacity is guaranteed for 600 charge cycles or 2 years whichever situation comes first 4 7 Battery pack care e Cleaning of the battery pack Clean the battery pack with a damp cloth The battery pack is splash proof but not waterproof Do not immerse the battery pack in water and do not clean the battery pack with a high pressure washer Handling of the battery pack Handle the battery pack with care to avoid damage Do not drop or impact the battery pack immerse it in water or clean it with a high pressure washer Do not open the battery pack there are no user serviceable parts inside Do not short circuit the terminals Awa RNING Mishandling of the battery pack could lead to severe damage or over heating In an extremely rare case a battery pack that has been severely impacted or otherwise mis handled could
30. l only one unit is showing in the fuel gauge on your display NOTICE When it is necessary to recharge the battery pack will emit a beep Charge the battery pack immediately Battery packs are best charged at temperatures around 20 C so avoid warm locations When coming in out of the cold allow the battery pack to get up to room temperature about 20 C before charging e Charge status indication On battery packs with a round charging port with translucent ring it is possible to check the charge status manually by touching the charge connector ring to activate the charge LED It will light up in the color corresponding to the charge level Green for 100 85 Orange for 85 25 and Red when below 25 Power supply 100 240V The power supply will adjust automatically to the local voltage e Charging Connect the connector of the power supply to the battery pack Connect the power supply to an appropriate power source WARNING Replace a damaged power cable immediately to prevent an electric shock EN 24 The light at the charging port of the battery pack will turn red It will turn yellow as soon as charging starts As soon as the yellow light on the battery charging port turns green the battery pack is fully charged Disconnect both the connector from the battery pack and the power source Charging a fully discharged battery pack usually takes about three to five hours depending of its maximum capacity After one
31. l take care of the correct charging procedure However you will save energy by disconnecting the power supply when the light in the charging port has turned green a GREEN ORANGE Quick START REAR Rack Battery Packs 1 4 Rear rack battery packs Removing the battery pack Insert the key in the lock twist the key clockwise 1 2 Now slide the battery pack rearwards out of the rear rack 3 4 After you remove the battery pack don t forget to take the keys out of the lock EIS o 0 2 Lu Placing the battery pack Slide the battery pack into the rack electrical contact side first 1 Carefully push all the way forward also through a slightly higher resistance at the end 2 3 Now turn the key of the lock counter clockwise until the battery pack is locked and take the key out of the lock 4 Do not ride the bike with the lock open A V VA E EN 8 Quick START DowntuBe BATTERY 1 5 Downtube battery pack Removing the battery pack Insert the key in the lock twist the key clockwise until the lock springs out 1 2 When the lock springs out the lever of the battery pack will be released Now take the key from the lock and pull the lever of the battery pack so that it slides upwards parallel to the down tube until it releases from the rail 3 When the battery pack is not on the bike always use the protective cover on the m S contacts on the frame to protect the elec
32. ntaining 39 Li Mn Lithium lon cells 48 V 8 5 Ah max 408 Wh m e Bontrager Interchange System compatibility The RIDE R250 2 R320 and R420 battery packs are compatible with the Bontrager Interchange System This means you can mount a n optional Bontrager Interchange basket or pannier on the rear rack of the bike by removing the plug from the battery pack Removing the battery pack from the bike Insert the key into the lock on the battery docking and turn it clockwise 1 2 The battery pack can now be taken off the bike Slide the battery pack out by pulling it to the rear 3 4 Don t forget to take the keys out of the lock after removal a Putting the battery pack onto the bike Slide the battery pack into the rear rack connector side first 1 Make sure the pack engages the rail 2 Slide all the way forward pushing through a slightly higher resistance at the end as the connector engages 3 Now turn the key of the lock until the battery pack is locked and take the key out 4 Do not ride the bike with the lock open EN 21 SE o 0 2 Lu 4 4 Downtube battery pack Battery pack size RIDE C420 down tube battery pack containing 52 Li Mn Lithium lon cells 48 V 8 8 Ah max 423 Wh e Bottle cage holder A bottle cage can be mounted on the C420 battery pack by installing the bottle cage holder This adapter can be mounted by 2 bolts Subsequently the bottle
33. o switch On Off the controller display light if present the front and rear lights This switches o 242 au Doo 21900 E on the front light the rear light and the backlight in the display L Ml The lights will stay On even when you stop Even when the battery 00 gauge shows empty there is enough energy to run the lights for about two hours If the battery pack is fully drained the lights will be powered by the system as it switches to generative mode automatically To switch the lights Off hold the button for 2 seconds m 0 a Mountain mode The Mountain Mode allows for longer uphill riding before the motor shows power reduction due to so called temperature derating As Mountain Mode limits the maximum motor torque the motor will stay cooler for a longer period of time Select this option by going to assistance level 4 and then press and hold the button for 2 seconds To return to assistance level 4 press the button once Removing and installing the BionX G2 controller To remove the BionX G2 controller from the bike press the catch at the back of the holder and slide the controller off towards the rear To install the BionX G2 controller onto the handlebar align the controller with its clamp and slide the controller forward until it clicks NOTICE To prevent loss of riding information please make sure that the system is switched Off befor
34. on On Off to move into the chosen menu In the programming menu buttons and will move to a higher or lower value Pressing button On Off will save the entry and move you to the next step or back to the regular display Codes CULT to switch between miles and kilometers 171 LIJ to set the time eidg J to swap the function of the buttons from left to right and vice versa 11 to change the display language on Pro controller only Use button to scroll through the languages 1 to set the correct wheel diameter EN 28 m EN 29 n A Nod M AINTEN 5 Maintenance After the first two to three weeks of use or 300 km have your dealer check the spokes in the rear wheel The motor is of the brushless type and requires no maintenance Check the connections of the system every two to three months Make sure that no dirt or moisture can get into the docking station connector when the battery pack is not on the bike If you notice anything like this clean with asmooth dry brush 5 1 Cleaning When cleaning the bike use a sponge and or a soft brush For the battery pack case a damp cloth suffices Use little water Keep water away from the electrical connections NOTICE Do not use a jet wash The powerful water jet may damage the electronics 5 2 Removal and refitting of wheels for bikes with a rear wheel motor Removal and refitting of the rear wheel is
35. ower regeneration level press button To switch from any level of Assistance to the first regenerative level press and hold the button To switch from any level of regeneration to the first assist level press and hold the button The G and the arrow will appear on the display during generation of energy Distance Odometer Chronometer Average speed Clock The right bottom corner of the screen shows the distance odometer chronometer and average speed Order of appearance trip distance odometer average speed time of day Press the button to switch modes To reset distance chronometer or average speed keep this button pressed for 2 seconds e Switching lights On Off Press the amp button for 2 seconds to switch On Off the Controller display light and if present the front and rear lights The lights will stay On even when you stop Once activated the text light On appears on the screen Even when the battery gauge shows empty there is enough energy to run the lights for about two hours If the battery pack is fully drained the lights will be gt gt muss p DIST ESTE Q DIST gt gt powered by the system as it switches to generative mode automatically To switch the lights Off hold the button for 2 seconds After switching Off the text
36. pack and if present panniers of the electrical bicycle and store it elsewhere in the vehicle during the drive e Always respect local laws about transportation of a n electric bicycle A WARNING The drivability of the vehicle may change with extra weight on the back of the vehicle f Because Li lon battery packs of this size and power are considered Dangerous goods class 9 when transporting regulations may restrict the transport of separate Li lon batteries in some places The restrictions apply to most airlines and some trucking companies But if you intend to ship or travel with your complete RIDE bike with installed battery pack the regulations are less strict Make sure to check ahead with your airline or carrier before booking your trip if it is allowed to travel with your complete RIDE bike MAINTENANCE 4 9 Programming This section explains how you set the odometer units miles or kilometers the clock the wheel diameter and how you can swap the functionality of the buttons and select the correct language EIS o 0 2 Lu To enter programming mode press buttons On Off and Mode switch for two seconds Four zeros will appear with the first zero blinking Enter the appropriate code by pressing button for a higher value for a lower value Press button On Off to select a value and move to the next digit After entering the correct value for the fourth digit press butt
37. problems The Service Indication is visible on the display of the controller When it shows this means that the electronic system recognizes a problem First try solving the problem by switching the RIDE system Off and back On If the error persists visit your dealer immediately for repairs The Service Indication can mean the battery pack has been impacted or mis handled causing an electrical fault In an extremely rare case a battery pack that has been severely impacted or otherwise mis handled could potentially catch fire In an emergency situation fully immerse the battery pack in a large container of water The system will not switch On no beep from the battery pack the LCD display remains blank First check the battery pack It must be in place and the lock must be pushed in fully Check all connectors and disconnect and reconnect if necessary Make sure that the controller is slid into its docking all the way If this does not help contact your dealer The motor is always in generative mode There is probably something wrong with the switch for generative braking in the right hand brake lever If there is something wrong with the generative braking switch try switching the system Off and On again If this does not help unplug the connector between brake lever and controller This should solve the problem but generative braking will be disabled Contact your dealer a After a repair or service the motor is not as powerful
38. quipped with the RIDE Link This device can be used to select a higher or lower assist or regeneration level and to turn the lights On Off without removing your hands off the handlebars The red throttle button on the RIDE Link is a convenient help to move the bike without pedaling upto 4 km h walking next to the E bike A WARNING Beware of unintended use of the throttle button when the system is switched On EN 6 m 7 QUICK START CHARGING 1 3 Charging Power supply The charging process is the same for both battery pack types They can be charged using the power supply on the bike or removed from the bike RIDE R250 2 R320 amp R420 RIDE C420 NOTICE When not in use charge a battery pack at least once every six months refer to paragraph 4 7 for detailed instructions e Charging the battery pack 1 Turn the system Off 2 Connect the connector of the power supply to the charging port of the battery pack and connect the power supply to the power outlet A WARNING Replace a damaged power cable immediately to prevent an electric shock 3 The battery pack will emit beeps and then the charging port will turn orange When the battery pack is full the charging port will turn green To stop charging just disconnect both connectors The battery packs with the round charging connector can be left connected to the power indefinitely The power supply electronics wil
39. r at the right hand side of the hub Make sure that both cables are unplugged 4 Disconnect the front brake V brakes Magura brakes release the front brake Roller Brakes unhook the cable and housing stop from the brake 5 Loosen and remove the axle nuts and washers 6 Lift the bike so that the wheel can be removed Take care not to lose the two torque blockers e Refitting of the front wheel 1 Make sure that the system is switched Off 2 Make sure that the torque blockers are on both sides of the axle with their arms pointing outwards see photo 3 Rollerbrake bikes make sure that the roller brake and the distance piece that centers the roller brake onto the hub are correctly in place 4 While sliding the wheel into the dropouts make sure that the arms of the torque blockers are below the axle in the open ends of the fork legs Rollerbrake bikes make sure the brake arm enters its retention bracket 5 Turn the wheel slightly backwards so that the torque blocker arms seat themselves against the corresponding lips on the fork legs EN 30 m EN 31 6 Tighten the wheel nuts equally and evenly to a torque of 40 Nm Otherwise the system might not work properly If you do not have access to a torque wrench you can use a normal wrench but ask your dealer to check the tightening torque of the nuts at the earliest opportunity 7 Reconnect the front brake Rollerbrake bikes make sure th
40. rmal wrench but have your dealer checked the tightening torque of the nuts at the earliest opportunity MAINTENANCE NOTICE On bikes without a derailleur the chain may not be adjusted too tight measured at the most tight point in the chain else the RIDE system does not work properly and can the rider lose control of the bike while riding Adjust the chain so that there is 10 20 mm of slackness in the 10 20 mm chain at its tightest spot when a force of about 100 g is applied 6 Reconnect the rear brake Rollerbrake bikes make sure that the bolt for the brake arm is securely tightened 7 Reconnect the motor connectors EIS o 0 2 Lu 8 Activate the system 9 Test ride to make sure that the system works 10 Check ifthe rear brake works A WARNING Switch the system Off before you disconnect or connect the connectors of the motor You may experience strong sparking and possibly electric shock if you fail to do so Removal refit of the front wheel No specific instructions are needed to remove or refit the front wheel 5 3 Removal and refitting of wheels for bikes with a front wheel motor Removal and refitting of the front and rear wheel is best left to your dealer If you are forced to do it yourself follow the following instructions e Removal of the front wheel 1 Make sure that the system is switched Off 2 Remove the battery pack from its docking station 3 Unplug the connectors of the moto
41. sisted speed Wheel nut torque Max load bike rider amp luggage Total weight bike incl battery pack 6 2 Battery packs RIDE R250 2 Voltage 37V Capacity 6 6 Ah Power 244 Wh Weight 2 Akg At least 600 full Life discharge charge cycles Charging time fully to 4 hours E discharged battery 125 kg TECHNICAL DESCRIPTION Brushless motor 250W 25 km h 40 Nm 23 4 28 0 kg depending on model RIDE R420 RIDE C420 RIDE R320 48 V 48 V 48 V 6 6 Ah 317 Wh 408 Wh 423 Wh 28 ke At least 600 full At least 600 full At least 600 full discharge discharge charge discharge charge cycles cycles to 5 hours 4 to 5 hours 6 3 Minimum and maximum temperatures for battery pack charge cycles 3 to 4 hours Max CC 45 5O 25 Status Min C Charging Use 10 o Storage 5 6 4 Power Supply Input voltage 100 VAC to 240 VAC Input current 1 6 A Output voltage 26 VDC Output current 3 45A 6 5 Compliance A standard RIDE electric bike Pedelec is EPAC Electrically Power Assisted Cycle compliance with European Norm EN15194 The RIDE Fast class E bikes Category only allowed in Germany Austria and Switzerland have EC type approval with regard to Directive 2 002 24 EC in addition to compliance with EN15194 EN 32 SE o 0 2 Lu m EN 33 PROBLEM SOLVING 7 Problem solving 71 Drive
42. switch the system Off When switched On the bike is in cycle mode zero assist Assistance Regeneration Level Push the button once for assistance level 1 again JUG lt 4r L KM h for higher levels Push the button to go to a lower level Regeneration levels can be controlled in a similar way O DIST UD t mre cen Push the button once for regeneration level 1 again for a higher level Push the button to reduce regeneration A WARNING It is strongly advised to ride away in a straight line when an assistance level is selected Never select assistance level 3 or 4 during maneuvering or riding away in a tight corner The powerful reaction of motor might take you unawares Switching lights On Off Press the button for 2 seconds to switch On Off the controller display light and if present the front and rear lights Once activated the text Light On or Light Off will appear in the lower field of the display See time average speed odometer trip distance Use button to change bike computer functions Order of appearance trip distance odometer average speed time To prevent loss of riding information please make sure that the system is switched Off before the controller is removed from the bike Using the RIDE Link Most bikes with the RIDE Pro controller positioned on the middle clamp are E equipped can be e
43. the Pedelec bikes except that the assistance does not stop at 25 km h but at 40 km h A WARNING Other road users may not expect a bicycle to go this fast NOTICE Maximum range on one battery charge depends very much on your style of use Due to the higher speed that can be reached be prepared to find the range slightly shorter than on regular Pedelec bikes that have a maximum assistance speed of 25 km h EN 14 INSTRUCTIONS FOR USE 4 Instructions for Use There are two types of controllers BionX G2 and RIDE Pro S t i trt m I 4 1 BionX G2 controller 1 Speed indication 2 Service Indication 3 Current assistance level 4 On button 5 Button 6 Distance Odometer Chronometer Average speed 7 Battery charge level 8 Mode switch Q button 9 on off 7 button 10 Current generation level A WARNING If the Service Indication a steady or blinking wrench symbol is visible on the display refer immediately to paragraph 7 1 for instructions Switching system On Off Press any of the two top buttons briefly to switch the system On The battery pack will beep four times the system will perform a short self check shown on the display as a countdown in the speed field and the system will activate o switch to On As soon as the system is On the screen will display and each function will be shown next to its corresponding button
44. to a power source or before you remove the battery pack to charge it 7 3 Display problems Occasionally the display active for 1 second This is normal this happens roughly every half hour as the system self checks SE o 0 2 Lu Display active for 1 second battery pack beeps This is normal this happens roughly every half hour as the system self checks and the battery pack should be charged e Display blank only lock visible Disconnect the controller amp reconnect or push Mode 5 times EN 34 m EN 35 LIMITED WARRANTY 8 Limited warranty Trek Bicycle Corporation warrants the motor the battery pack and the controller against defects in workmanship and materials for a period of two 2 years for the original owner This warranty does not cover Normal wear and tear Improper assembly Improper follow up maintenance Installation of parts or accessories not originally intended for or compatible with the bicycle as sold Damage or failure due to accident misuse abuse or neglect Labor charges for part replacement or changeover Underperformance of the battery pack if it has been fully discharged and charged more than 600 times within the two year warranty period This warranty is void in its entirety by any modification of the frame fork or components This warranty is expressly limited to the repair or replacement of a defective item and is the sole
45. to the first assist level press and hold the button A WARNING It is strongly advised to ride away ina straight line when an assistance level is selected Never select assistance level 3 or 4 during maneuvering or riding away in a tight corner The powerful reaction of motor might take you unawares EIS o Lu Regeneration When the bicycle generates electricity for the battery the system is in generation mode The motor then works as a dynamo There are four levels of regeneration The level of assistance is shown by the bar graph on the left below the digits for speed The narrow graph on the display shows the amount of energy delivered to the battery To increase the regeneration level press button For regenerative level 1 press once Press again to increase the regeneration level to a higher level For a lower regeneration level press button To switch from any level of assistance to the first regenerative level press and hold the button When the rear brake lever is pulled the system always switches to generating The arrow and G will show in the display Distance Odometer Chronometer Average speed The bottom of the display shows distance odometer chronometer and average speed Press the Q button to switch modes To reset distance chronometer or average speed keep this button pressed for 2 seconds EN 16 Switching lights On Off Press the 5 button for 2 seconds t
46. trical system from water 5 o Contacts at the bottom side of the down tube Placing the battery pack Position the battery over the downtube with some space between the seat tube and the lower end of the battery pack 1 Now slide the battery pack down onto the rail 2 Use the lever to lower the battery pack carefully during the last phase of sliding so that the connectors engage 3 Be sure that the connector at the bottom of the battery pack and the connector on the docking engage properly When the battery pack is fully in place push the lock in until it clicks 4 Do not ride the bike with the lock open EN 9 DESCRIPTION 2 Description EIS o 0 2 Lu 2 1 Specific parts for the electric bicycle There are several models of electric bicycles with different equipment options Find the options that are on your electric bicycle In the pictures of the bikes you will find the battery pack 1 the motor front or rear 2 the controller 3 the brake switch 4 and the wiring harness 5 e Battery packs There are four types of battery packs for RIDE bicycles 1 RIDE R250 2 battery pack rack type containing 30 Li Mn Li Ion cells 37 V 6 6 Ah max 244 Wh 2 R320 battery pack rack type containing 39 Li Mn Li Ion cells 48 V 6 6 Ah max 303 Wh 3 RIDE 420 battery pack rack type containing 39 Li Mn Li Ion cells A8 V 8 5 Ah max 408 Wh 4 RIDE C
Download Pdf Manuals
Related Search