Ritron PATRIOT PLUS RTX-454 Owner`s manual
Contents
1. SAFETY STANDARDS The FCC has adopted a safety standard for hu man exposure to radio frequency electromagnetic energy emitted by FCC regulated equipment The Quick Talk conforms to the standards effective at the time of its equipment authorization by the FCC In general these stan dards recommend that you DO NOT allow the antenna to come very close to or to touch exposed parts of the body especially the face or eyes while transmitting e DO NOT transmit near electrical blasting caps or in an explosive atmosphere e DO NOT allow children to play with radio transmitters e BE AWARE of the conditions which cause the unit to transmit SERVICE Federal law prohibits you from making any internal adjustments to the transmitter and from changing transmit frequencies unless you are specifically designated by the licensee DO NOT ADJUST OR TAMPER with components or the printed circuit board in any manner not directed in this manual Unauthorized adjustments may render the unit inoperable repair will be at owner s expense If your radio equipment fails to operate properly or if you wish to have the radio serviced contact your authorized dealer or call Ritron at 317 846 1201 and ask for the Repair Department RITRON INC LIMITED WARRANTY WHAT THIS WARRANTY COVERS RITRON INC RITRON provides the following warranty against defects in materials and or workmanship in RITRON RQX 150 XT RQX 450 XT RQX 446 XT AND RQX 454 X2. Defects or damages in which the serial number has been removed altered or defaced IMPORTANT This warranty sets forth the full extent of RITRON s express responsibilities regarding the covered products and is given in lieu of all other express warranties What RITRON has agreed to do above is your sole and exclusive remedy No person is authorized to make any other warranty to you on behalf of RITRON Warranties implied by state law such as implied warranties of merchantability and fitness for a particular purpose are limited to the duration of this For assistance call RITRON at 800 872 1872 or go to www ritron com limited warranty as it applies to the covered product Incidental and consequential damages are not recoverable under this warranty this includes loss of use or time inconvenience business interruption commercial loss lost profits or savings Some states do not allow the exclusion or limitation of incidental or consequential damages or limitation on how long an implied warranty lasts so the above limitations or exclusions may not apply to you Because each covered product system is unique RITRON disclaims liability for range coverage or operation of the system as a whole under this warranty WHO IS COVERED BY THIS WARRANTY This warranty is given only to the purchaser or lessee of covered products when acquired for use not resale This warranty is not assignable or transferable HOW TO GET WARRANTY SERVICE To rec
3. from the steel front plate Lift the steel front plate from the OUTPOST XT enclosure to expose the OUTPOST Callbox mounted inside Use a medium Philips screw driver to complete the battery installation loosening the four 4 plastic screws at the corners of the front half of the housing These screws are captive to the Housing to prevent damaging them DO NOT remove them Disconnect the in line connector between the Front and the Back halves of the Housing Note the positive and negative polarities and of each cell Press six Alkaline D cells into proper position NOTE When all batteries are in place confirm that the RED wire contacts the positive pole of the first battery and the BLACK wire 9 PRE DRILLED MOUNTING HOLES 4 CORNERS contacts the negative pole of the last battery as shown in FIG 2 Reconnect the in line connector between the Front and the Back halves of the Housing After re assembling the OUTPOST Callbox inside the OUTPOST XT enclosure place the steel front plate on the enclosure To prevent voiding Manufacturers Warranty DO NOT pinch gasket over tighten cross thread strip or remove captive screws DO NOT drill or penetrate the internal RF electronics enclosures with any additional holes secure the steel front plate with the 4 Tamper Proof Torx screws with the T 25 Tamper Proof Torx Driver Take care when re assembling this enclosure to carefully seat the top half w
4. on unit location and installation height of a standard antenna the OUTPOST XT covers the area of a 1 Watt portable radio of the same frequency band To increase range use an external antenna that is mounted higher Refer to the RAM 1545 Magnet Mount Antenna on page ii Page 8 RQX 454 Standard and XT Model Use PC Programming Software RPT PCPK 8 0R12 1 Refer to the Owner s Manual for disassembly instructions to PC Program the radio 2 Execute the Programming Software and go to the Main Title Page Click on Plus Series then click on Start pO Plug the programming cable into the RQX and power the RQX by pressing the button on the front case Click on Radio then click on Read Radio The RQX 454 will read out as a Model RQX 454 Click on Edit then click on Tune Radio Click on Misc Click on Power Saver Off Time then click on Tune O o cl o 0 To calculate the decimal number for your desired off time divide your desired time in seconds by 32 Round the number to two places pass the decimal point Example 10 seconds factory default divided by 32 31 NOTE 1 The maximum amount of shut off times is 255 seconds 2 DO NOT type 0 for the Battery Saver Off Time unless your RQX 454 has firmware version 1 14 or later Doing so will render the RQX inoperable Units that do not have version 1 14 or later do not contain the necessary firmware for the On all the tim
5. standard BNC male connector be used to mate with the BNC connector located on the internal RF electronics enclosure 4 If installing an external antenna form a drip loop using the antenna cable inside the XT enclosure Position the drip loop below and away from the BNC connector located on the top of the internal RF electronics enclosure Page 10 RITRON OutPost XT Owner s Manual F C C LICENSING AND REGULATIONS The Rules and Regulations of the United States Federal Communications Commission FCC require you or your radio service provider to have a license for your radio system before activating the OUTPOST XT radio transmitter If you already are operating a licensed radio system you probably can add a OUTPOST XT without any changes to that license The station licensee is responsible for ensuring that transmitter power frequency and modulation are within the limits specified by the station license and also for proper operation and maintenance of the radio equipment These responsibilities include checking the transmitter frequency and modulation periodically using appropriate methods Ritron or your Ritron Dealer can assist you with all these requirements You may also contact the FCC directly by any of the following methods To obtain copies of FCC forms and instructions use the FCC Fax On Demand system at 202 418 0177 Request Document 000600 For more information go to the FCC Internet Website at http www fcc gov gt
6. the battery cable or the EXPO 12 Power Connector back into the radio Carefully place the radio assembly into the front case and secure it with the 4 metal seal screws Secure the top of the RF enclosure to the bottom of the Callbox with the 4 captive screws NOTE The antenna may be positioned to either side of the RF enclosure After re assembling the RF enclosure place the steel front plate on the enclosure Secure the steel front plate with the 4 Tamper Proof Torx screws with the T 25 Tamper Proof Torx Driver FACTORY DEFAULT eUnit is set for medium volume eBattery saver Auto Shut off is set for 10 seconds Page 7 RITRON OutPost XT Owner s Manual REPROGRAMMING THE AUTOMATIC SHUT OFF TIME RQX 150 450 Standard and XT Models Use PC Programming Software RPT PCPK 3 0R19 1 Refer to the Owner s Manual for disassembly instructions to PC Program the radio 2 Execute the Programming Software and go to the Main Menu page 3 Plug the programming cable into the RQX and power the RQX by pressing the button on the front case Press 1 to read the RQX information 5 The RQX 150 XT will read out as a Model SST 150 The RQX 450 XT will read out as a Model SST 450 6 Use the down arrow key or enter key to get to the Access Radio Tech Fields field Type tunel 8 The cursor should automatically go to the Battery Saver Off time field 9 The factory default time is 10 secon
7. two way radio When the switch opens or closes a user recordable custom voice message is automatically transmitted to all radios on the same channel frequency Ideal for remote monitoring of power failures e liquid levels intrusion or tampering temperature sensing e unattended doors to name only a few of the 1000s of applications For assistance call RITRON at 800 872 1872 or go to www ritron com Page 13 RITRON OutPost XT Owner s Manual CARE AND MAINTENANCE MOISTURE When antenna sealing recommendations are followed the OUTPOST XT is highly weather resistant in outdoor environments Do not immerse the unit in water TEMPERATURE The OUTPOST XT is designed to operate between 22 and 140 F Like all electronic equipment the VIBRATIONS SHOCK Though the OUTPOST XT is designed to be rugged it cannot be expected to survive extreme abuse CHEMICALS Do not use harsh corrosive or abrasive chemicals to clean the OUTPOST XT case use only a cloth moistened with water Do not attempt to clean the OUTPOST XT should not be subjected to extreme heat A shaded area is an ideal outdoor location printed circuit boards inside the enclosure ALL RITRON PRODUCTS ARE PROUDLY MADE IN THE ASA A Eze 01072 1 10 0 4 0 0 01 Ritron Pub 14500028 Rev C 08 02 P O Box 1998 Carmel IN 46082 1998 505 W Carmel Dr Carmel IN 46032 USA PH 317 846 1201 800 USA 1 USA 800 872 1872 FAX
8. 2 OUTPOST XT COMPONENTS eere 3 IDENTIFICATION OF CONTROLS amp CONNECTORS eere 4 INSTALLING BATTERIES INTO THE OUTPQONST icona tu ERAN REC nu R ios 5 BATTERY Ql qc 5 PTT PROGRAMMING THE OUTPOST XT RQX 150 450 446 ONLY 6 To Place the OUTPOST XT into Programming Mode 6 To Program a Frequency and QC Tone 6 PC PROGRAMMING THE OUTPOST XT RQX 150 450 454 onera etes 7 REPROGRAMMING THE AUTOMATIC SHUT OFF n Ete UT T 8 MOUNTING THE OUTPOST XT 8 To Mount the OutPost XT ueeesesuuess 8 Coverage eee 8 EXPO 12 EXTERNAL POWER 12 VDC INPUT BATTERY BACKUP KIT OPTIONAL 9 Back Up Battery Installation 9 SEALING THE INTERNAL ANTENNA 10 External Power Antenna Use 10 FCC REQUIREMENT 5 25 eint odus or eo E Pobu obo epar See eosas Eus 11 LIMITED WARRANT Y e ecciona coi cos eus ne conico 11 COMPATIBLE PRODUCTS AND SYSTEMS 12 FIGURES DESCRIPTION PAGE A OUTPOST XT COMPONENTS 3 1 TOP HALF OF INTERNALHOUSING CONTROLS amp CONNECTORS 4 2 BOTTOM HALF OF INTERNAL HOUSING SHOWING CELL POLARITY 5 3 REA
9. 317 846 4978 Web www radiocallbox com E mail ritron ritron com For assistance call RITRON at 800 872 1872 or go to www ritron com Page 14
10. 462 6750 464 3250 464 8250 469 5000 469 5500 463 2625 464 9125 464 6000 464 7000 Frequency Color Green Dot Red Dot Purple Dot Model RQX 450 Frequency Color Yellow Dot Brown Dot Silver Star Gold Star Red Star Blue Star White Dot Black Dot Orange Dot TABLE 2 QUIET CALL TONE CODES QUICK TALK Other Radio Brands Tone Code Other Radio Brands Tone Code Freq Hz Freq Hz CODE Use Code 44 to program No Tone for systems without a Coded Squelch Interference Eliminator feature Refer to Page 4 Step 5 and NOTES at the bottom of the page HOW TO PC PROGRAM THE OUTPOST XT RQX 150 450 446 454 XT Dealers and Authorized Service Maintenance Personnel Only If your frequency is not found in Table 1 page 4 the frequency and tone must be programmed with a PC using specialized RITRON Programming Software NOTE Only RITRON dealers have access to programming software Contact RITRON at 800 USA 1 USA for the location of your nearest Authorized RITRON Dealer e Models RQX 150 XT amp RQX 450 XT require RPT PCPK 3 0 R19 PC for PC programming e Models RQX 454 454 N XT require RPT PCPK 8 0R12 for PC programming eModel RQX 446 XT requires PC software not available at time of printinng Please contact RITRON for further details Follow instructions from page 6 steps 1 3 2 Loosen the 4 captive screws in the corners of the RF enclosure These screws are captive to the h
11. ISC mode it would make the use of batteries impractical select Power Saver select TUNE set Power When using this feature it is recommended that the Saver Off Time to 0 zero select SAVE select optional EXPO 12 external power kit be used EXIT and then remove power from the radio and disconnect the programming cable The RQX 454 To Enable the Intercom Feature The Intercom Mode 454 N XT is now set for Intercom Mode can only be enabled using the PC Programmer OUTPOST XT MODELS and FREQUENCIES Model Band Frequency Range Signalling Formats RQX 150 XT VHF FM 150 155 MHz Std 155 160 MHz Opt CTCSS RQX 450 XT UHF FM 460 470 MHz Std 450 460 MHz Opt CTCSS RQX 446 XT UHF FM 460 470 MHz Wide or Narrow Band TX 460 MHz Opt CTCSS DCS 1stQ 2002 RQX 454 XT UHF FM 450 470 MHz Narrow Band CTCSS DCS LTR Passport RQX 454 N XT UHF FM 450 470 MHz Narrow Band RX TX CTCSS DCS LTR Passport The RQX 150 450 Models are PTT programmable to specific tones and channel frequencies They are also PC programmable to any frequency channel within the radio s band using the RPT PCPK 3 0 R20 or higher PC Software xx The RQX 454 models is PC programmable ONLY and requires the RPT PCPK 8 1R5 or higher PC Software The RQX 446 model is PTT programmable and or PC programmable Software is not available at time of printing Call Ritron for details Refer to page 6 for instructions on matching the OUTPOST XT operating freque
12. R VIEW OF THE OUTPOST XT HOUSING 8 4 INTERNAL VIEW OF EXPO 12 9 5 SEALING THE INTERNAL ANTENNA 10 TABLES DESCRIPTION PAGE 1 FREQUENCY CODES 2 eee rese 5 2 QUIET CALL TONE CODES 6 RITRON OutPost XT Owner s Manual ABOUT THE OUTPOST XT TAMPER RESISTANT WIRELESS CALLBOX GENERAL INFORMATION The OutPost XT is a ruggedized version of the popular OutPost Callbox The XT model consists of four basic components External rugged fiberglass XT enclosure with pre drilled mounting holes inserts and mounting ears Vandal resistant stainless steel faceplate with stainless steel vandal resistant PTT push to talk button Internal weather resistant sealed and gasketed RF electronics enclosure with attached acoustic tube Internal flexible antenna with BNC connector IMPORTANT NOTES Refer to FIG A page 3 1 The external XT fiberglass enclosure itself is not designed to provide a complete weather resistant seal therefore weep holes in the XT enclosure will allow moisture and or condensation to escape 2 The external fiberglass XT enclosure has pre drilled mounting holes with inserts on the rear of the enclosure DO NOT drill or penetrate the external XT enclosure for mounting purposes Use only the pre drilled holes for mounting the fiberglass XT Callbox See page 8
13. RITRRON Qureosr XT Vandal Resistant Wireless Callbox Owner s Manual TRAILS MARINAS SCHOOLS HOSPITALS CAMPUSES ROADSIDES PUBLIC PARKS PLAYGROUNDS CAMPGROUNDS GOLF COURSES HOTELS MOTELS PUBLIC BEACHES SHOPPING MALLS AMUSEMENT PARKS PARKING FACILITIES UNATTENDED GATES p a ee MADE IN THE Ritron Pub 14500028 Rev C 08 02 CopyrightO 2002 RITRON INC ALL RIGHTS RESERVED RITRONG PATRIOTG JOBCOMG Quick Assi Rr and Quiet Call amp are registered trademarks of RITRON INC Outrost and Quick Talk are trademarks of RITRON INC P O Box 1998 Carmel IN 46082 1998 505 W Carmel Dr Carmel IN 46032 USA PH 317 846 1201 800 USA 1 USA 800 E 2 1872 FAX 317 846 4978 Web www radi ocallbox x com E mail ritron ritron com WHAT THIS MANUAL COVERS This manual Ritron Item RQX 150 450 446 454 XT covers programming operation and installation of the OUTPOST XT 2 Way Callbox ACCESSORIES These replacement and optional items are available from Ritron and its authorized dealers Item Description AFB 1545 Standard 16 in Flexible Whip Antenna EXPO 12 External Power 12VDC Input Battery Back Up Kit RAM 1545 Magnetic Mount Antenna w 20 ft of Cable and a BNC Connector EXPO 12 EXTERNAL RAM 1545 POWER BATTERY ANTENNA BACK UP KIT PHYSICAL DIMENSIONS The OUTPOST XT ext
14. T Wireless Callbox units under normal use and service during the applicable warranty period as stated below Accessories means antennas wire cable and items contained in the programming and programming service kits WHAT IS COVERED FOR HOW LONG WHAT RITRON WILL DO OutPost XT 1 year During the first year after date of Callboxes purchase RITRON will repair or replace the defective product at RITRON s option parts and labor included at no charge Accessories Antennas 90 days After date of purchase WHAT THIS WARRANTY DOES NOT COVER e Any technical information provided with the covered product or any other products Installation maintenance or service of the product unless this is covered by a separate written agreement with RITRON Any products not furnished by RITRON which are attached or used with the covered product or defects or damage from the use of the covered product with equipment that is not covered Defects or damage including broken antennas resulting from misuse abuse improper maintenance alteration modification or modification to any housing neglect accident or act of God or the use of covered products other than in normal and customary manner or improper testing or installation Defects or damages from unauthorized disassembly repair or modification or where unauthorized disassembly repair or modification prevents inspection and testing necessary to validate warranty claims
15. U E LIQUID TIGHT AN aay STRAIN RELIEF t POSITIVE POWER CONNECTION WIRES FROM EXTERNAL EE NEGATIVE POWER CONNECTION POWER SOURCE POLARIZED IN LINE BATTERY CONNECTOR FIG 4 INTERNAL VIEW OF EXPO 12 COVER PLATE NOT SHOWN For assistance call RITRON at 800 872 1872 or go to www ritron com Page 9 RITRON OutPost XT Owner s Manual HOW TO PROPERLY SEAL THE INTERNAL ANTENNA DO NOT drill or penetrate this enclosure Use Applying Seal Tape only the pre drilled mounting holes located in 1 Attach the antenna to the connector on the each of the four corners of the bottom half of the enclosure Take care when re assembling the enclosure Be sure to carefully seat the recessed OUTPOST RF enclosure and position at the elbow into a 90 angle area and gasket of the top half with the bottom 2 Begin wrapping seal tape at base of antenna half DO NOT pinch gasket over tighten cross connector such that the base of the antenna is thread strip or remove captive screws sealed against the enclosure top 3 Overlap the seal tape as you wrap upward around Antenna The product comes standard with a the connector and antenna Continue to overlap flex antenna Model AFB 1545 with a BNC seal tape around the connector base past the connector This antenna will provide approximately articulating portion of the antenna and several 7 mile or more range in line of sight conditions with no obstacles inches up the t
16. ds Type in the time in seconds from 1 to 256 for your desired shut off time NOTE DO NOT type 0 for the Battery Saver Off Time unless your RQX has a label marked 314G0158 on the outside of the case Doing so will render the RQX inoperable Units that do not have the 314G0158 label do not contain the necessary firmware for the On all the time option 10 Press the F10 key 11 Press 2 12 Wait for the next prompt press C 13 Wait for the radio programmed ok message 12 Remove the power from the RQX and unplug the RQX from the computer MOUNTING THE OUTPOST XT CALLBOX The external fiberglass XT enclosure has pre drilled mounting holes with inserts on the rear of the enclosure To prevent voiding the Manufacturer Warranty DO NOT drill or penetrate the external XT enclosure for mounting purposes Use only the pre drilled holes for mounting the fiberglass XT Callbox The OUTPOST XT can be mounted to virtually any surface by using 4 410 32 Panhead screws secured into the 4 corner rear inserts or by using the enclosed metal mounting ears that are secured using the included 4 210 32 Panhead screws If the metal mounting ears are used use a maximum size of 5 16 diameter bolts to mount the OUTPOST XT The OUTPOST XT is designed to be mounted vertically The drain holes are located on the bottom of the enclosure to allow for moisture to escape that may occur during outdoor use Coverage Depending
17. e option To check click on Edit then click on Radio ID 11 Type in your decimal number 12 Click on Save 13 Click on Exit 14 Remove the power from the RQX and disconnect the RQX from the computer PRE DRILLED HOLES WITH INSERTS 4 CORNERS USE ONLY FORMOUNTING MOUNTING EARS 4 CORNERS REAR VIEW OF THE OUTPOST XT ENCLOSURE RITRON OutPost XT Owner s Manual EXPO 12 EXTERNAL POWER 12VDC INPUT BATTERY BACK UP KIT OPTIONAL The optional EXPO 12 will facilitate powering the 2 Way Radio Transceiver in the RQX OUTPOST Callbox from an external 12 VDC source Battery back up capability is a standard feature of the EXPO 12 A 12 VDC 1 5 Ampere power supply not included with the EXPO 12 is required The optional AC to 12 VDC RPS EX wall transformer is available from Ritron e The Battery Back up feature of the EXPO 12 allows the OUTPOST Callbox to continue operating for a period of 8 hours talk time if external power is interrupted Either non rechargeable 6 AA Alkaline Lithium or re chargeable Ni cd batteries can be used e By moving jumper PJ101 on the EXPO 12 Board rechargeable batteries can be trickle charged Refer to the illustration below Jumper Position A NOTE DO NOT attempt to charge Alkaline batteries Back Up Battery Installation 3 Place the jumper over the correct two PJ101 pins 1 Remove the four 4 4 screws securing the metal for the batteries you are using rechargeable
18. eive warranty service you must deliver or send the defective product delivery costs and insurance prepaid within the applicable warranty period to RITRON INC 505 West Carmel Drive Carmel Indiana 46032 Attention Warranty Department Please point out the nature of the defect in as much detail as you can You must retain your sales or lease receipt or other written evidence of the date of purchase and deliver it along with the product If RITRON chooses to repair or replace a defective product RITRON may replace the product or any part or component with reconditioned product parts or components Replacements are covered for the balance of the original applicable warranty period All replaced covered products parts or components become RITRON s property RIGHTS TO SOFTWARE RETAINED Title and all rights or licenses to patents copyrights trademarks and trade secrets in any RITRON software contained in covered products are and shall remain in RITRON RITRON nevertheless grants you a limited non exclusive transferable right to use the RITRON software only in conjunction with covered products No other license or right to the RITRON software is granted or permitted YOUR RIGHTS UNDER STATE LAW This warranty gives you specific legal rights and you may also have other rights which vary from state to state WHERE THIS WARRANTY IS VALID This warranty is valid only within the United States the District of Columbia and Puerto Rico Pa
19. erior dimensions are 11 0 H x 925 W x 6 0 D The OUTPOST XT weight is 6 5 lbs w o batteries Fr Power Requirements 6 D Cell Alkaline Batteries not included or optional EXPO 12 External Power 12VDC Input Battery Backup Kit Refer to page 3 of the OUTPOST XT Owners Manual for battery information and page 7 of the OUTPOST XT Owners Manual for information on the EXPO 12 WARNING IMPORTANT SAFETY INFORMATION NOTICE The Outpost XT is not intended for communicating information to protect life or property and must not be used for these purposes To reduce the risk of fire electric shock or personal injury follow these basic safety instructions when using this unit 1 Read and follow all instructions 2 Use only alkaline D cell batteries 3 During thunderstorms avoid contact with this unit and any external antenna system or wiring Page ii TABLE OF CONTENTS DESCRIPTION PAGE WHAT THIS MANUAL COVERS ii ACOBSSORIES sasine eee ne enn eee tes dau ii DIMENSIONS xistexiscpis tuis ed isi mis eiut utu uUdi tuni cuu di boat os ii WARNINGS ossiani ii ABOUT THE OUTPOST XT WIRELESS CALLBOX 1 General Information sseeeuessssss 1 Operating the OutPost XT sseeeueessssse 2 Intercom Always on Feature 2 Models and Frequencies
20. f the antenna to be used it is always best to seal the antenna connection using seal tape Refer to page 10 WARNING If the OutPost XT is to be used outdoors it is imperative that the antenna connection be sealed to prevent voiding Manufacturers Warranty Take care to range test the OUTPOST XT before installing and thoroughly engineer the system BEFORE drilling or penetrating the XT enclosure Please refer to page 10 for recommended practices and detailed information For assistance call RITRON at 800 872 1872 or go to www ritron com Page 1 RITRON OutPost XT Owner s Manual ABOUT THE OUTPOST XT TAMPER RESISTANT WIRELESS CALLBOX 5 Power The standard OutPost XT will operate using 6 D size alkaline batteries The Warning OUTPOST XT can also be used with the Take care and thoroughly engineer the optional External Power 12 VDC Input Battery system BEFORE drilling or penetrating the Backup Kit model EXPO 12 If external power XT enclosure EXPO 12 is required the the owner dealer is Caution If both external antenna and responsible for making modifications holes external power are required in the same to the XT enclosure please refer to page 10 callbox DO NOT co locate the antenna and for recommended practices and detailed power cable in the same conduit Run information separate conduit for each cable OPERATING THE OUTPOST XT NOTE The OUTPOST XT will not receive a call until To Receive a Response a call
21. ge 11 RITRON OutPost XT Owner s Manual Complete Wireless Communication Solutions From Page 12 Ritron We Build Wireless Solutions For nearly 3 decades Ritron has been designing manufacturing and supplying reliable professional wireless communication products for users worldwide Ritron wireless products will improve the operation safety and profitability of any organization by providing instant voice communication between key employees throughout the workplace Portable Radios Communicate with multiple workgroups instantly with a push of the button Rugged and lightweight with built in weather scan VHF models only automatically finds NOAA broadcasts Other features include Interference Eliminator Loud and Clear Audio Removable Quick Swap Battery and Drop in Charging Capability Accessories Ritron offers a wide variety of headsets earsets remote speaker microphones multi unit chargers and carry holsters to meet all your wireless communication needs Wireless Intercom Two way Base A m m R ITR O N Station Monitor 110 VAC or 12 VDC desktop or wall mountable EXCLUSIVE radio that is compatible with any VHF UHF radio system Includes built in Weather Scan VHF models only loud audio output for noisy locations built in microphone with automatic gain control and rugged metal housing Optional Public Address PA modification available Ideal for in plant schools e retail stores e jobsite vehicles c
22. has been initiated by the OUTPOST XT 4 When you have finished speaking release the THE OUTPOST XT AUTOMATICALLY ON PTT Button SHUTS OFF WHENEVER THERE IS INAC TIVITY FOR TEN 10 SECONDS 2 Any reply to you will be heard through the OUTPOST XT speaker If a reply is not received within 10 seconds of releasing the ON PTT Button the unit sounds a low double tone and shuts off automatically To call again press and hold the ON PTT Button and begin speaking after the beep To Initiate a Call Press and hold the ON PTT Button on the unit listen for the beep and begin speaking into the MIC For best communication speak as closely as possible into the microphone The OUTPOST XT is designed so you will be heard clearly when you speak while pressing the ON PTT Button at a distance of up to 3 feet from the microphone INTERCOM Always On FEATURE FOR THE RQX 454 454 N XT The RQX 454 454 N XT can be programmed to oper PC Programming Software RPT PCPK 8 0R12 ate as a two way intercom When this feature is acti 4 Refer to the PC PROGRAMMING THE OUTPOST vated the automatic shut off Is disabled and the callbox XT section to program the RQX 454 454 N XT will remain on in standby mode allowing it to receive a ware call from another radio at any time Since the radio is 2 Once the radios information has been Read under constant current drain always on in the standby select EDIT select TUNE RADIO select M
23. hin shiny section of the antenna Optional Antennas The Ritron model RAM 1545 magnet mount antenna can be used to increase range Be advised that the magnet mount antenna MUST be attached to a magnetic ground plane PECORE SEALING metal to function properly Overlap sealing tape to include the antenna connection and the top of the RF enclosure 5v SEALING THE ANTENNA If the product is to be ex IT 7 en mMin used outdoors it is imperative that the entire S LTI HT 7 antenna connection be sealed with seal tape to UD Overlap sealing tape 1 inch provide proper operation and prevent voiding AFTER SEALING E beyond the rigid section of the warranty dena Regardless of the antenna you use it is always best to weatherproof the antenna connection using seal tape Seal tape can be purchased at most Industrial amp Contractor Supply Stores Hardware and Home Center otores or Electronic Supply Stores NOTICE Failure to follow these instructions will cause damage to the product prevent proper sealing of the enclosure and will void the Manufacturers Warranty RECOMMENDATIONS FOR EXTERNAL POWER ANTENNA USE 1 Do not route external 12 VDC power cable and external antenna cable through the same conduit 2 Itis recommended that metal conduit fittings and metal conduit be used to route either external power and or external antenna cable to maintain vandal resistance integrity 3 Itis recommended that a
24. it pause digit pause 0 pause 4 gy pause 9 When all four digits are programmed press and release the PRocRAM Save Button The unit sounds a triple tone NOTE An error tone sounds if you try to save an incorrect digit To correct the programming press and release the PRoGRAM Orr Button When the unit sounds a low tone you may start over at Step 3 4st 2nd digit Pause gigit pause 2 JJ pause pause 10 Press and release the PRocRAM Orr Burrow the unit sounds a low tone The OUTPOST is now ready for use NOTES Ten 10 clicks O zero Page 6 Program 44 to enter No Tone for Quiet Call You must enter 44 to match radios without tone codes If you make a programming click error press and release the PRocRAM Orr Button to turn the unit OFF and start over If the unit does not sound the confirming triple tone when you attempt to save your programming the unit was factory or dealer customized to disable programming Consult the radio owner or your Dealer Refer to Frequency and Tone Code tables at right and on the following page TABLE 1 FREQUENCY CODES VHF Business Band Model RQX 150 MHz 151 925 154 540 154 515 154 655 151 685 151 715 151 775 151 805 151 835 151 895 154 490 151 655 151 745 151 865 QUICK TALK FREQ CODE n gt 467 7625 464 5500 464 5000 467 8500 467 8750 467 9000 467 9250 469 2625 462 5750 462 6250
25. ith the recessed area and gasket into the bottom half RED WIRE 10 BATTERY HOLDER 1 WARNING DO NOT USE NICKEL METAL HYDRIDE BATTERIES IN THE OUTPOST BLACK WIRE IN LINE CONNECTOR INSIDE VIEW FIG 2 BOTTOM HALF OF INTERNAL HOUSING SHOWING CELL POLARITY BATTERY LIFE Use non rechargeable Alkaline D cell batteries for maximum battery life The OUTPOST XT should operate for one 1 year on a set of Alkaline batter les depending upon usage Cooler temperatures degrade battery life Exposure to 10 C 50 F will reduce battery life to 90 of normal Exposure to 20 C 4 F will reduce battery life to 3596 of normal For assistance call RITRON at 800 872 1872 or go to www ritron com Page 5 RITRON OutPost XT Owner s Manual HOW TO PTT PROGRAM THE OUTPOST XT MODELS RQX 150 450 446 ONLY NOTES Refer to Table 1 Frequency Codes and Table 2 QC Tone Codes when programming the OUTPOST For PROGRAMMING Button locations refer to the Internal View of the Front of the Housing in FIG 1 page 4 Before you begin the programming process refer to page i 3 for disassembly of the XT enclosure To place the OUTPOST into Programming Mode 1 Loosen the 4 plastic screws in the corners of the unit These screws are captive to the Housing to prevent damaging them DO NOT remove the captive screws from the housing 2 Make sure the unit has ba
26. ncy to that of an existing radio system Page 2 RITRON OutPost XT Owner s Manual JHVMQOMNVH 2 31Vd AYNSOTONA 34 Q3 1V3S ONILNNOW TVN3 LLNI PF SM32S SAILdVO AIYNSO1ONS LX A OL abed oj sajay ebeyoed ade je s y uo suononJjsul 0 JOJOY JUSJEAINDS JO 79 9 2t YOCUS OIPEY esp vot JeDuiejc sn edej Jees uw pejees eq Joj euuoo pue euugjue y jeu eAjgeJeduul si 3 SIOOP NO pesn eq 0 S 1X LSOdLNO 24 JI SLNANOdWOD LX LSOdLNO AHL AO M3IA Q3GO 1IdX34 V7 9lJ v SH3N31SVJ LINVLISIS3 M3dlAV L LAO ALV 1d 329 V 1331S SS3 INIVLS e Page 3 For assistance call RITRON at 800 872 1872 or go to www ritron com RITRON OutPost XT Owner s Manual IDENTIFICATION OF INTERNAL CONTROLS AND CONNECTIONS Refer to FIG 1 1 ANTENNA CONNECTOR 6 SPEAKER The antenna radiates radio signals Before using After a message has been sent from the the OUTPOST XT make sure the antenna is OUTPOST XT any reply from another radio may securely fastened into the connector be heard through the speaker If the OUTPOST XT is to be used outdoors see 7 MICROPHONE MIC page 10 for instructions on properly sealing the For best communication speak as closely as antenna connector possible into the microphone The OUTPOST XT 2 PROGRAM BUTTON RQX XT 150 450 is designed so you will be heard clearly when you speak while pressing the ON PTT Button at a This button is used to enter freq
27. of manual for details 3 The internal RF electronics enclosure is mounted inside the XT enclosure and is designed to provide a weather resistant seal The internal RF electronics package has a top and bottom half The enclosure is gasketed and held together with four captive screws in the top half Do Not remove the screws from top half The RF electronics are contained in the top half and the battery or optional external power kit are contained in the bottom half DO NOT drill or penetrate the internal RF electronics enclosure with any additional holes Take care when re assembling this enclosure to carefully seat the top half with the recessed area and gasket into the bottom half Make sure the black strain relief nut is properly tightened around the PTT cable assembly to insure weather resistant seal DO NOT pinch gasket overtighten cross thread strip or remove captive screws Failure to heed this warning will prevent proper sealing of the enclosure and will result in voiding Manufacturers Warranty Antenna The OutPost XT Callbox comes standard with an internally mounted flex antenna AFB 1545 This antenna will provide approximately 75 mile line of sight range or more depending on terrain Optional external antennas can be used However the owner dealer is responsible for making modifications holes to the XT enclosure to allow for external cabling of the antenna Refer to page 10 Regardless o
28. ommunity repeater systems loading docks e construction trailers or anywhere that fixed two way communication is needed RITRON OutPost XT Owner s Manual The Leader in Workplace Two Way Radio Systems Advantages of Ritron Wireless Products Unique products and features not available from any other source Adds speed flexibility and responsiveness to any organization Fully compatible with virtually any existing two way radio system Designed to work together as a complete system No mnothly service fees or airtime charges Made in the U S A A Wireless Radio Callboxes Battery operated 6 alkaline D cells callboxes RITRON available in basic or rugged models provide EXCLUSIVE instant wireless communication over existing two way radio systems without costly trenching extensive wiring or dedicated phone lines Ideal for Hotels Motels Golf Courses Schools Jl erence dette dee Public Parks Playgrounds e Roadsides Marinas Blow eredi rtg e Parking Lots or Garages e Receiving or Delivery zs Docks Campuses e Shopping Malls Beachs and Pools Campgrounds and Hiking Trails e Unattended Gates hi V o 4 TWO WAY CALLBOX ONE WAY CALLBOX V a LL E i A Wireless Alert Monitoring RITRON No need to run wires phone lines or pay a person for 24 7 monitoring The low cost battery operated EXCLUSIVE 6 alkaline AA cells Quick Talk Alert permits wireless monitoring of virtually any sensor or switch from a
29. or plate covering the battery holder non rechargeable See PJ101 location below 2 Install the desired batteries rechargeable or non NOTES When the OUTPOST has rechargeable rechargeable see Notes below and at right batteries installed place the PJ101 jumper Match polarities of the battery to the Battery In position A Holder as shown below When the OUTPOST has non rechargeable NOTES Forrechargeable batteries use ONLY batteries installed to prevent damaging the AA size Ni cd Nickel Cadmium cells batteries place the PJ101 jumper in the position B over two pins For non rechargeable batteries use ONLY AA size Alkaline or Lithium cells 4 Reinstall the metal plate removed in Step 1 secure it with the four 4 4 screws e DO NOT USE Nickel Metal Hydride cells Make sure the black strain relief nut is properly tightened around the PTT cable assembly to insure weather reisistant seal DO NOT drill or penetrate the internal RF electronics enclosure with any additional holes Use only pre drilled mounting holes PRE DRILLED MOUNTING HOLES JUMPER POSITION A 4 CORNERS PJ101 JUMPER SET IN RECHARGEABLE BATTERY POSITION HOLDER 6 Due to space limitations inthe XT model the installation of the liquid tight strain relief must be reversed HN PJ101 JUMPER SET IN NON RECHARGEABLE POSITION Ne AA SIZE A dt CELLS 6 A giu
30. ousing to prevent damaging them DO NOT For assistance call RITRON at 800 872 1872 or go to www ritron com 10 12 14 RITRON OutPost XT Owner s Manual remove the screws from the housing Lift the top half of the RF enclosure from the bottom Remove the 4 metal seal screws from the front of the top half of the RF enclosure Carefully lift the radio assembly away from the inside of the front of the RF enclosure and plug the Programming Cable adaptor into the 3 5mm Jack located on the top of the radio assembly Execute the Programming Software for the radio on your computer Make sure the radio has batteries installed or is powered by an external 12 VDC source through the EXPO 12 To turn the unit on press the ON PTT button on the front of the unit Follow the instructions for PC programming the radio according to the software When PC Programming the VHF RQX 150 XT will read out as a model SST 150 the UHF RQX 450 XT will read out as a model SST 450 the UHF RQX 446 XT will read out as a model RQX 446 the UHF RQX 454 N XT will read out as a model SST 454 WARNING ONLY FREQUENCY AND TONE IN FORMATION should be altered when using the RITRON Programming Software Changes to other features could render the unit inoperable After the programming is complete and the information has been saved to the radio unplug the radio from the battery holder or the EXPO 12 and remove the Programming Cable Adaptor Plug
31. tteries installed NOTE The voltage of the batteries must be greater than 6 VDC to program properly 3 Press and release the ON PTT Button on the front of the unit Press and release the PRocRAM ENaBLE Button An audible beep will sound to confirm the unit is in programming mode To read out beep out Radio Channel content 5 Press and release the Program Save Button The radio will begin to sound a series of beeps each series of beeps is equal to one digit of each 2 digit frequency code or Quiet Call Code see chart below that is programmed into the radio See Tables 1 and 2 on this page 6 After the beeps are completed a triple tone will sound To Program Frequency and QC Tone Codes 7 Choose a frequency code Table 1 and if desired a QC tone code Table 2 If you are not using a QC tone program 44 No Tone for the QC code 8 Enter the codes in the sequence shown below by clicking the PRocRAM Button the number of times equal to each digit of the codes EXAMPLE Frequency Code 02 Tone Code 44 e Click the PRocRAM Button ten times to program 0 pause the unit sounds a beep e Click the PRocRAM Button two times to program 2 pause the unit sounds a beep e Click the PRocRAM Button four times to program 4 pause the unit sounds a beep e Click the PRocRAM Button four times to program 4 pause the unit sounds a beep FREQUENCY CODE 02 TONE CODE 44 st nd dig
32. uency and Quiet distance of up to 3 feet from the microphone Call code information 3 OFF BUTTON RQX 150 450 8 IN LINE BATTERY CONNECTOR This button is used to turn the OUTPOST XT OFF The in line battery connector connects the radio to when programming is complete the Battery 4 PROGRAM SAVE BUTTON RQX 150 450 This button is used to save the programmed 9 PRE DRILLED MOUNTING HOLES Mounting holes accommodate 6 panhead screws information to securely mount the unit to a variety of surfaces 5 PROGRAM ENABLE BUTTON RQX 150 450 Refer to page 5 FIG 2 Pressing this button when the unit is ON puts the OUTPOST XT into Programming Mode 10 BATTERY HOLDER NOTE Model RQX XT 454 must be programmed The rugged battery holder securely holds six by a RITRON Dealer 6 D cell batteries in place Refer to page 5 FIG 2 ee 1 ANTENNA CONNECTOR 2 PROGRAM BUTTON 3 OFF BUTTON 4 SAVE BUTTON 5 ENABLE BUTTON ACUSTIC TUBE 6 SPEAKER 7 MICROPHONE LIQUID TIGHT STRAIN RELIEF 8 IN LINE BATTERY CONNECTOR CAPTIVE SCREWS 4 Front View of Top Half Inside View of Top Half FlG 1 TOP HALF OF INTERNAL HOUSING CONTROLS amp CONNECTORS Page 4 RITRON OutPost XT Owner s Manual INSTALLING BATTERIES INTO THE OUTPOST XT Refer to FIG 1 and FIG 2 Using the T 25 Tamper Proof Torx driver remove the 4 Tamper Proof Torx screws
Download Pdf Manuals
Related Search