The Oscilloscope: Operation and Applications
Contents
1. feature of the oscilloscope For example in figure 14 to measure V1 Figure 14 Differential Measurement Example Channel A measures V1 V2 relative to ground while channel B measures V2 relative to ground By pushing the invert button you negate the voltage displayed on channel B Then you can add the channels together with the ADD display mode The waveform now displayed is V1 V2 V2 VI Bandwidth 3 dB Measurement This measurement is easily done by first finding the maximum gain max VOUT VIN at frequency w and adjusting the oscilloscope so that the sinewave fills seven divisions peak to peak A 3dB point can be found by increasing and or decreasing the frequency until the gain is reduced to V2 If the input voltage has remained constant this will occur when the output voltage is five divisions peak to peak Vut 1 5 ae Se SOHO a divisions Vou max y2 The frequency is then simply read with a frequency counter or the oscilloscope Not by reading the dial of the signal generator Risetime The risetime indicates how quickly a circuit responds The risetime is the time it takes a waveform to go from 10 of the voltage range to 90 of the voltage range This is in response to a square wave and the output voltage must settle to a steady state voltage 0 and 100 Most oscilloscopes have dotted lines on the graticule marking the 10 and 90 points to aid in this measurement Usually these dotted lines assume2. Half power is also called the 3dB point At this point the voltage has decreased to 70 7 of its maximum This means that only one half of the maximum power would be dissipated in a resistive load Keep in mind that an oscilloscope that is rated at 20 MHz is usually only accurate to 4 MHz for non sinusoidal waveforms before distortion becomes a problem With ac coupling figure 4 an oscilloscope has another series RC circuit It acts like a high pass filter HPF If you are viewing low frequency signals when ac coupled not only will you not be able to measure any dc offset but you will also be removing some low frequency information Input DC AC coupled frequency Figure 4 AC coupled Oscilloscope Input Circuit and Frequency Response Oscilloscope Operation Voltage vs Time The main function of an oscilloscope is to show voltage vs time This is done by applying a ramp or sawtooth waveform into the X axis amplifier as shown in figure 5 During the rising edge of the ramp the electron beam scans across the screen When the voltage drops back to OV the beam is turned off and quickly goes back to its starting point This is signified by a thick line when the beam is on and a thin one when it is off blanked To obtain a stable picture on the CRT screen the ramp waveform has to be in phase with the signal that you want to observe This is done with a triggering circuit The triggering circuit allows the oscilloscope to draw r
3. a voltage directly via the connector at the bottom right of the panel or the Horizontal can be driven by an internal timebase circuit which generates the voltage Timebase In the timebase mode the horizontal signal is from an internal source which changes linearly with respect to time Hence the beam is deflected to give us a calibration of time for the horizontal scale The position control the pull x5 magnifier switch the time range selection switch and the range CAL knob all affect the X axis of the display Trigger Sources The TRIGGER SOURCE may be selected from one of three sources CH 1 CH 2 or EXT Look at the bottom right of the control panel Calibration Source The Calibration Source is an internal source available on the oscilloscope Look at the bottom right side of the front panel The output is labelled 0 3 V This is a 1000 Hz square wave the 50 duty cycle is not accurate 10 3 Oscilloscope Applications Voltage and Time Measurements Note The oscilloscope measures divisions of deflection not voltage or time From the divisions of deflection you can calculate the time or voltage Differential Measurements An important application of the oscilloscope is differential measurements Such measurements are necessary because both vertical channels have one terminal connected to the chassis common ie single ended To measure a floating off ground voltage you have to use the invert and add
4. have two waveforms that do not have the same frequency it is still possible to show them as two stable waveforms on a normal oscilloscope In figure 11 you will notice that if the triggering occurs at the X both waveforms are in phase ie at the same phase each time the timebase triggers The condition for a stable display is not that two waveforms have to be of exactly the same frequency but that when they are triggered they have to be in phase Or n f1 m f2 where n m are integers That is not necessary but it is sufficient There are many other ways to achieve a stable trace when you consider that the trigger circuit will wait for the next triggering point There is also a control on some oscilloscopes called hold off which allows you to add a delay between the end of the trace being drawn and the time when the triggering circuit starts to look for the next triggering point That can be used to stabilize the display under some circumstances Remember that all of this applies only for repetitive waveforms that are properly triggered If the triggering is not stable or the waveform is not repetitive you will see a constantly moving image or several images offset and superimposed A slightly more complicated block diagram of an oscilloscope with the typical functions found in the laboratory is illustrated in figure 12 Accuracy There are many factors affecting the accuracy of oscilloscope measurements There are errors due to the
5. input channel voltage divider timebase control the use of magnifiers the accuracy to which the CRT deflection can be read beam thickness temperature etc The voltage divider error will be the same for all readings that are done on the same timebase and voltage range but may be different each time the range is changed Measurements over only two divisions can incur two to three times the error of those made over the centre eight divisions If the phase angle is used in a trigonometric function this error can be multiplied by the slope of the function Consider that the tangent of a 1 phase error entered at 85 degrees is much worse 20 than the same 1 error on a sine function 0 2 at the same angle To get a feel for this look at the Taylor expansion of the trigonometric functions It is wise to consult the user manual for a particular instrument s accuracy specifications 149 YAWA SIXY X e NOLLISOd dalsandnv SIXVA YalndAv Tou e XI 300W d33Ms WON orny Ax 1x3 OlwuvaNoo 40193130 1INOYNIO TH9 ASVESWIL a BAN 34018 439941 A WHO O ado1s AIG AWLL 13447 43991 YOLWNNALLY unda Haare O WHON ANI ONIHOLIMS NOLLIS
6. Od ALIaW10d AICISLIOA TANNVHOD aay nyna ETH HI E E T YOLYNNILLY NOILISOd LAdNI AIQ SLIOA Figure 12 Oscilloscope Block Diagram 2 Iwatsu Model SS 5702 Oscilloscope Accuracy The Iwatsu SS 5702 oscilloscope is used in this laboratory All measurements on the graticule should be made over as many divisions as possible For simplicity assume the Iwatsu SS 5702 oscilloscope s error is 5 for a measurement on either the vertical or horizontal scales over eight divisions Front Panel Controls The front panel controls shown in figure 13 will be described in the remainder of this section OSCILLOSCOPE DC 20MHz POSITION CH1 gt POSITION TIME DIV CH1 CH2 DUAL ADD V MODE Y MODE POSITION CH2 POLARITY AUTO INV NORM VOLTS DIV E o SWEEP MODE 2 mV Sl C EXT DC TV V PULL 1 50 AC DC m X5 MAG i a COUPLING CD vV 10 5 CAL CH1 CH2 EXT SOURCE gt TRIG ROWER ON TRACE NTEN FOCUS SCALE X MODE OR ROTATION Intel LN Ov BM ee8 Figure 13 The Iwastu SS 5702 Oscilloscope Front Panel Controls The power trace rotation intensity focus and scale illumination controls are located at the bottom centre The vertical controls and input selection are on the left side The horizontal controls and horizontal input selection are on the right side The trigge
7. The Oscilloscope Operation and Applications The Oscilloscope Oscilloscope Operation X vs Y mode An oscilloscope can be used to measure voltage It does this by measuring the voltage drop across a resistor and in the process draws a small current The voltage drop is amplified and used to deflect an electron beam in either the X horizontal or Y vertical axis using an electric field The electron beam creates a bright dot on the face of the Cathode Ray Tube CRT where it hits the phosphorous The deflection due to an applied voltage can be measured with the aid of the calibrated lines on the graticule First we will consider the circuitry that amplifies and conditions the voltage to be measured the Amp block in figure 1 Deflection Plates Y Axis Y 9 Amplifier o Xx X Axis Amplifier Inverter Figure 1 X vs Y Deflection Block Diagram of the CRT The deflection of the oscilloscope beam is proportional to the input voltage after ac or dc coupling The amount of deflection Volts Division depends upon the setting of the AMPL DIV control for that channel see figure 2 The input signal can be ac or dc coupled Ac coupling involves adding a series capacitor This has the effect of blocking removing the dc bias and low frequency components of a signal Dc coupling does not have this problem and therefore allows you to measure voltages right down t
8. age point to anywhere that is convenient for you Oscilloscope Inputs The input of the oscilloscope can usually be modelled as a resistance and a parallel capacitance see figure 3 The resistance is usually 1MQ but it and the capacitance can vary greatly The total or effective capacitance includes the oscilloscope circuitry approx 30 pF cables approx 30 pF m and stray capacitance The resistance will draw current from the circuit while the capacitance will add an RC time constant with its associated time delay frequency response and distortion of some waveforms The common connection black lead or shield at the input of the oscilloscope goes to the metal case as the symbol by the input connector shows Because of this the common input can only be connected to a OV point in the circuit Since the common inputs for both the A and B channels are connected to the case they are effectively shorted together DC coupled Figure 3 DC coupled Oscilloscope Input Circuit and Frequency Response Frequency response is calculated or measured by applying a pure sinusoidal waveform to a circuit The circuit response is the output voltage divided by the input voltage This is a complex number that can also be expressed as a magnitude gain and phase Due to limitations in the amplifiers the oscilloscope s frequency response is limited The manufacturer simply lists the half power point for the oscilloscope without any external effects
9. ase measurements are done by comparing the measured time to the period of the waveform Oscilloscope Two Channel Operation You can view two voltage waveforms at once by using two Y axis vertical input channels The individual channels are sometimes labelled as 1 and 2 or as A and B Since there is only one electron beam you have to share its drawing time between both waveforms This may be accomplished using either the chop or alternate modes When in the chop mode figure 8 the oscilloscope displays a little bit of channel A then a little bit of B then A then B during a single sweep of the electron beam If you increase the timebase to about lus division you can start to see the individual pieces as it chops between one channel and the other channel Chop Display Trigger _ Points Figure 8 Chop Mode In the alternate mode figure 9 the oscilloscope will sweep the electron beam twice across the screen The first time it will draw the signal from channel A and the next time from channel B At very low timebase settings you can see it draw one channel and then the other in successive passes Note When you use the alternate function the two waveforms that you see are from different points in time and the triggering circuit has to trigger twice Alternate Display Trigger Ponts 7 Figure 9 Alternate Mode The reason that you can see a non fl
10. dow with the timebase The time base control allows you to set the time division that the beams takes to scan across 4 the screen Just like the voltage selector there is a calibration knob in the middle of the control Unless the vernier calibration knob is clicked in to its most clockwise position the time per division is unknown When set to AUTO automatic triggering the oscilloscope will always show a trace However when you use a manual triggering mode DC AC many strange things can happen For example if the triggering voltage or level is set to 10V and the waveform never exceeds 5V the triggering circuit will never trigger and the screen will stay blank You may think that in a condition of no triggering you would still have a bright dot on the screen because the electron beam would go to its home or undeflected position Since the oscilloscope is designed to work with a moving electron beam a stationary beam can very quickly burn a hole in the phosphorous coating of the screen To prevent this there is a blanking circuit which turns off the electron beam Blanking occurs when there is no triggering or when the electron beam is sweeping from the right edge back to the left side of the screen Time measurements are done the same way as voltage measurements As long as the timebase is calibrated you multiply the number of divisions by the number of seconds per division to get the total time difference Ph
11. epeatedly the same waveform over and over by identifying the same point on a repetitive waveform Deflection plates Ramp waveform Figure 5 A Ramp driven X axis input The triggering circuit allows you to select a voltage an analog value and an edge or slope positive or negative for the triggering circuit to compare to the input waveform When the two are equal the circuit puts out a pulse This pulse triggers the ramp waveform generator to do one cycle of its rising and falling edges Once the ramp has started a cycle of increasing voltage it can not be retriggered until it has completed the full ramp and returned to OV This is illustrated in figure 6 for a single cycle and in figure 7 for multiple cycles Trigger negative slope Voltage lt i Time Voltage Figure 6 A Triggering Example Vitigger Trigger Pulse l fl Timebase P S Ramp VAL Figure 7 Several Triggering Cycles Not only do you have control over the starting point of the ramp but the amount of time that the ramp takes to reach its maximum voltage the right hand side of the CRT screen can be adjusted with the timebase control In essence you have a window You can move the window to any point on a waveform with the triggering circuit and you can change the size of the win
12. ickering image on the screen is because the phosphorous coating on the CRT has persistence In essence the phosphorous acts like a low pass filter and averages several images that are drawn on the screen By viewing two signals at a time you can measure relative time differences By combining a voltage and phase measurement relative to the appropriate reference you can measure a phasor value With a two channel oscilloscope you have the ability to trigger on each waveform and electronically switch chop or alt between them as well A block diagram of a oscilloscope has now become as shown in figure 10 Triggering clrcutt Figure 10 A Simple Oscilloscope Block Diagram Some oscilloscopes offer a way to alternately trigger as depicted in figure 11 When combined with alternate displaying you can stably display two waveforms of any frequency by alternately showing each channel and triggering on the channel that is being drawn This way the oscilloscope is acting like a two beam scope with both waveforms triggering at the same voltage and slope However there is no way to know what the relationship is between one waveform and the other when using alternate triggering Altomare rigger Display M A VAA J lan wal a N SNA YA AAA a Up J r li Noy YA V NA 7 V Trigger Polnts Figure 11 Stable Triggering of Two Different Frequencies If you
13. o 0 Hz Ac coupling is useful when you are trying to measure a small ac voltage that is on top of a large dc voltage A typical example is trying to measure the noise of a dc power supply Amplitude A DC per division Invert Position Input A Voltage signal iy o divider 0 PE Figure 2 Amplifier Block Diagram Amplifier Features AMPL DIV This abbreviated name varies but it is generally some short form of amplitude per division The control is a simple voltage divider attenuator which is used to change the sensitivity of the oscilloscope At a 1 volt DIV setting a deflection of one major division on the graticule represents a one volt change at the oscilloscope input Calibrated voltage measurements The small knob within the AMPL DIV control must be rotated clockwise into its detente position for the amplifiers to be calibrated Otherwise the voltage division will be some unknown value greater than what the dial indicates INV There is almost always a control which lets you invert one channel This can be used along with the ADD function to subtract two voltages This is necessary because the common input black lead of the oscilloscope cable can only be connected to a OV node If channel A has V1 V2 and channel B has voltage V1 then the reading of channel A channel B V1 V2 V1 V2 Position For each axis there is a control which lets you shift the electron beam With this you can set the zero volt
14. ring selection section is at the bottom right The power on off trace rotation intensity focus and scale illumination Trace rotation has to be checked with just a straight line across the screen of the oscilloscope The intensity should be adjusted to a mid point or more clockwise The focus of the beam can be done while observing the straight line display The scale illumination can be adjusted to the operator s preference Vertical Inputs Vertical channels are used for measuring voltage The beam is deflected vertically as a result of the signal being applied to the vertical input of the channel CH CH 1 and CH 2 are the labels for the two vertical inputs Each channel has a position control a range selection switch a pull x5 knob a coupling selector switch AC GND DC and an input connector Each channel Range switch VOLTS DIV has a smaller knob in the middle of the Range Selector Switch And there is an arrow showing that the Range Selector Switch is in the CAL position when rotated fully clockwise In the centre of the two channel sections is the channel selection switch You can choose to have CH 1 CH 2 both DUAL or ADD In addition CH 2 has a Polarity switch You push the polarity switch in to INVERT the polarity of the signal being displayed The NORM or out position is the normal position of the polarity switch Horizontal Inputs The EXT HORIZONTAL IN can be supplied
15. that 0 is the lowest line of the graticule and 100 is the highest line The measurement as shown in figure 15 also includes the risetime of the oscilloscope and the squarewave source 11 100 pops pcpo gi to sig b 7 90 ee cet ie ee eel lee el et 8 N L i j fi fi fi reference als aa Kany waveform LEE ee 10 24 ee 0 risetime phase k 3 1 dlv 180 deg 10 div Figure 15 A Risetime and Phase Measurement Phase Phase is most accurately measured when the waveform is as large as possible and the difference is measured at the zero crossings Typically the timebase is uncalibrated so that a 180 degree section of the waveform is expanded to the full 10 divisions of the graticule Then the sign of the phase can be determined by observing more than one period of both waveforms Both waveforms must be symmetrical about the centre line of the graticule The angle is determined by phase of divisions 180 degrees 10 divisions 12
Download Pdf Manuals
Related Search