DMAX Automotive Diagnostic Tool
Contents
1. Figure 4 USB Driver Setup Wizard Error After the message box Please Connect USB Device to PC appears See Figure 5 connect the DMAX Tool USB device to the Personal Computer and make sure that it is powered up USB status LED is lit Press the OK button DMAX USB Driver 1 0 Setup XI Please Connect USB Device ta PC and Press Button Figure 5 USB Driver Setup Wizard message box B If the USB Driver was installed successfully the USB Status LED should light up orange To check the driver version and the operation status on the PC with Win XP operating system go to Start gt Setting gt Control Panel gt System gt Hardware gt Device Manager gt Human Interface Device gt DMAX USB Device See Figure 6 fl 24 DVD CD ROM drives H Floppy disk controllers Ei g Human Interface Devices DMAX USB Device ER HID compliant consumer control device a HID compliant device HID compliant device E HID compliant device Figure 6 DMAX USB device driver location Note If the USB driver 15 not installed reinstall it by using the USB Driver Setup Wizard Chrysler SKIM ch rysler SKIM USB Driver k Figure 7 USB driver Setup Wizard ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 6 5 THE USB DEVICE SERIAL NUMBER and SOFTWARE UPDATE To get the DMAX USB Device serial number the DMAX USB Device has to be connected to the PC and the software has to be2. ChSKIM 1 01 Help Update About Jeep Grand Cherokee Lim 2000 SKIM Humber Humber Country Code Humber 0057 Select Vehicle M inia Enter the SKIM number IF the KIM number iz ncomect val lock the module E rites new VIM number vou want to bring module to unpeogramesd state nos VIH feld blarked Enter new Counkry Code If you wart to bring module to unprogramed state put Country code field to FF Head SKIM Press Vakdate Data Button lo Start operation Read DTCs OTC Figure 27 The VIN number and the Country Code fields edit B In couple minutes you will see the next screen see Figure 28 ChSKIM Jeep Grand Cherokee Lim 2000 skik Humber Number 55042298AD c aS mi pmo edi Fead SKIM Read DTC Figure 28 SKIM WCM VIN Edit procedure 15 completed B To make sure that the VIN number has changed read the module info Press the Module info Button see Figure 29 ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 18 4 Jeep Grand Cherokee Lim 2000 VI Part Humber 55042298AD Select Vehicle Module Into SKIM Read Clear DTCs Edit Figure 29 Verifying the VIN Edit procedure ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 19 10 KEY PROGRAMMING VIA THE OBDII The Key Programming function is
3. Note On EEPROM memory the Ist pin is usually marked by the round groove Figure 13 The Connection Help Screen x m L m Figure 14 The Connection Help Screen detailed view ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 10 B Press the Continue Operation button If there 1s a poor contact between the clip and the memory the Pin Tester Error screen will appear see Figure 15 Pins with a bad connection are marked by red color A couple of reasons could lead to this problem For example the varnish cover was not removed completely from the pins or the SOIC 8 Clip was not mounted well on the memory When the poor contact problem is resolved the SKIM number would be read automatically see Figure 16 ChSKIM joj xj Hep update About deep Grand Cherokee Lim 2000 Number 5504 2238AD Select Vehicle T i sor s Info m Tester Figure 15 Pin Tester Error Screen ChSK IM zlo x Jeep Grand Cherokee Lim 2000 Part Number 56042298AD select Vehicle Module Info Fead SKIM Read DTC Clear DTCs SKIM AVCH VIN E di Figure 16 SKIM number screen ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 11 7 SKIM NUMBER READING VIA OBDII J1850 BUS The SKIM reading via the OBD II connector is implemented to work with second generation modules which support the diagnostic way to work with the target module As the J1850 protocol is used the commu
4. 2006 SEIUOSABAK 2007 05Q26221AM 2005 SGDM5275AC 1850 Dodge Status 12000 pus deep Commande 206 seosameao t pe Jeep Commander 2007 0502619946 CAN Jeep Grand Cherokee 2007 Jeep Grand Cherokee 2005 emer Je Te Jeep Grand Cherokee D5D251854F Jeep Liberty 200 0502607140 Liberty 004 5601020840 1850 1850 Jeep Liberty Spa 6053020 35080 185 Jeep Liberty Spot 58053020 35080 ln deep Wrangler 20 earo CAN Jeep wirange Rubicon 5n 020940 J1850 J1850 1418850 Plymouth Neon Highline iM4671722AC 1050 MES J1850 Plymouth Neon Highline 0559995 _ 24CU2Prog 1860 1850 Figure 12 The SKIM reading procedure ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 9 B After the message Put Programmer clip on to Memory appears see Figure 13 put the SOIC 8 EEPROM Clip on to the memory as it is shown in the picture Pay extra attention to the Ist pin Both first pins on the memory and on the clip should match see Figure 14 Otherwise there is a risk of damage to the memory and the D MAX USB module First pin is marked by red color on the SOIC 8 clip Note On the SOIC clip the first pin is marked by red color 9 SOIC 8 clip supplied with the D MAX USB module may look different from what shown on the picture
5. in progress orange or blinking Figurel The DMAX Tool USB device front panel At the rear panel there are two connectors OBD II and PROG See Figure 2 The OBD II connector goes to the vehicle OBD II plug through the OBD II cable The PROG connector supports the programming of EEPROM memory Use the SOIC 8 EEPROM Clip for programming the EEPROM in circuit Note Pay attention to the EEPROM 1 pin It should be connected to first pin of the SOIC 8 EEPROM Clip Please see detailed pictures in the DMAX Tool software Figure 2 The DMAX Tool USB device rear panel Figure 3 The DMAX Tool USB device ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 4 To operate with the DMAX Tool a user has to install the control software on the Personal Computer The DMAX Tool software requires not only the preinstalled NET Framework Ver 3 5 package but also the installed USB device driver Please follow next steps to complete the installation z Check if the NET Framework Ver 3 5 package is installed on your PC If you use the Win XP you should go to Start gt Setting gt Control Panel Add Remove Programs See Figure 3 Microsoft Framework 1 1 Add New ig Microsoft NET Framework 2 0 Service Pack 1 Size 195 00MB Programs j5 Microsoft NET Framework 3 0 Service Pack 1 245 00MB Microsoft NET Framework 3 5 Size 25 88MB Click here for support information Used rarely LastUsed On 10 3 2008
6. DMAX Rev 3 DMAX Automotive Diagnostic Tool User s Guide TABLE OF CONTENTS mure 3 2 CHECKLIST AND REQUIREMENTS 3 S Wb Aere GE 4 INS TACLATTON eerte imm mud muU IU 5 5 THE USB DEVICE SERIAL NUMBER and SOFTWARE UPDATE 7 IN CIRCUIT SKIM READING BY THE CLIP inn ia pospe a bedna neke 8 7 SKIM NUMBER READING VIA OBDII J1850 BUS esee nne 12 8 THE SKIM NUMBER READING VIA THE OBDII CAN BUS 16 9 THE VIN NUMBER EDIT VIA THE OB DID iriennerien insannin asa 17 10 KEY PROGRAMMING VIA THE OBDII eere eee eee eene eene eene 20 11 KEY ERASING VIA THE OBDM uva ona NE sitter ausi etra rod qd qa arae sesta serta 22 12 READ CLEAR DIAGNOSTIC TROUBLE CODES eere 24 12 ERRORS AND TROUBLESHOOTING 26 Naboji TOOL 28 ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 2 1 PREFACE This manual will guide you through the installation and operation of the DMAX Automotive Diagnostic Tool The DMAX Tool has been designed not only to work with Chrysler vehicles via the OBD II connector but also to direct the EEPROM programming via the programming clip The DMAX Tool supports either 1850 or CAN communication inter
7. HE SKIM POPPER TOOL Skim Solder Gun with unique tip to access the on board chip Includes Solder Gun Skim Tip and 20 Black Dot Plugs The PERFECT Add On for the ACI ChSKIM Code Reader M Finally easy access to the Skim Chip simply heat the solder gun Special Price Gently press against the casing Create the perfect access hole Clip to chip to read skim module Cover hole with Black Dot Plug done S 311 South Fossil St E i OOL Russell KS 67665 P 785 445 3533 amp COMPUTERS 5445 3533 DMAX Automotive Diagnostic Tool ODMAX 2008 2009 28
8. KIM software select Dodge Durango 2005 Adv SLT 2005 and press the Read SKIM button see Figure 24 B x Help Update About Dodge Durango Adv SLT 2005 Number 560405424N Select Vehicle Module Info Fiead 5 Read DTCs Cea DTCs SKIM CM VIN Erase key Program a Key Figure 24 The SKIM number reading via OBD II CAN B Turn the ignition on and press the Continue Operation button In couple seconds the next screen will appear ChSKIM j joj Hap Update About Dodge Dur Adw SLT 2005 VIN Number SKIM Number 7777 Part Number 0542AN Part Humber 56040542AN Software Version 10 00 05 Code 04 Canada NEN GUN Sie Loo Pomas E Figure 25 The SKIM number reading via OBD II step 1 ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 16 9 THE VIN NUMBER EDIT VIA THE OBDII The VIN number edit function is useful if you have replaced the SKIM module or the PCM module After the new module has been installed the VIN number in the SKIM module and the VIN number in the PCM module have to be matched To edit the VIN number in the SKIM module the SKIM number is required Thus read the SKIM number first as described in Sections 6 7 Also the Country Code edit function is implemented This section describes step by step the operation with the Chrysler SKIM module part number 56042298AD installed in a 2000 Jeep Grand Cherokee Lim Other
9. To change this program or remove it from your computer click Change Remove Change Remove Figure 3 Microsoft NET Framework 3 5 If there is no Microsoft NET Framework 3 5 please download the Microsoft NET Framework Version 3 5 Redistributable Package x86 from this address http www microsoft com and install it im Execute Setup exe to install the DMAX Tool software Follow the instructions to select installation options E After installation of this software the USB driver Setup Wizard will start working Se Figure 4 DMA USB Driver 1 0 Setup loj x Welcome to the DMA USB Driver 1 0 Setup Wizard This wizard will guide you through the installation of OMAK OUSE Driver 1 0 It is recommended that you clase all other applications before starting Setup This will make it possible to update relevant system Files without having to reboot your computer Click Install to start Ehe installation Install Cancel Figure 3 USB Driver Setup Wizard ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 5 99 If the Error message There is currently connected device appears See Figure 4 you should disconnect all USB devices from the PC and press the Retry button WDREG Error x 1 There is currently 1 connected device using WinDriver Jj Please disconnect or uninstall all connected devices from the Device Manager and press Retry Ta reload WinDriver press Cancel and reboot
10. Vehicle Modules Info DIC FAILURE Read SKIM Read DTCs Clear DTCs SKIMAWCMAIN Edi Erate Keys Progam akey Figure 38 Clear DTCs C Note After the Clear DTCs procedure is completed the software reads DTCs automatically DMAX 2008 2009 DMAX Automotive Diagnostic Tool 25 12 ERRORS AND TROUBLESHOOTING This section describes most recently encountered problems errors and repair solutions B Problem Program will not install or run Causes This problem can appear if Microsoft NET Framework Version 3 5 or higher is not installed B Solutions Download Microsoft NET Framework Version 3 5 or higher from Microsoft com E Problem USB status LED see Figure 1 is dark E Causes This problem can appear if there is no power applied to the USB connector B Solutions Check the USB Cable Try to connect the DMAX Tool USB device to another computer B Problem OBD II status LED see Figure 1 is dark E Causes This problem can appear if there is no power applied to the OBD II connector to the Ext 12V connector B Solutions Check the connection between DMAX Tool USB device and a vehicle Apply 12 Volt to the Ext 12V connector B Error Message No External 12 Volt OBDII Power Supply Error Programmer Power Supply Error B Causes This message can appear if there is no power applied to the OBD II connector or to the Ext 12V connector B Solutions Check the co
11. a 2000 Jeep Grand Cherokee Other similar modules could be done in the same manner The new Skim Popper tool allows you to gain access and read the Skim Chip Refer to the section 13 the Skim Popper tool If you do not have this tool please do next steps very precise to prevent damaging of a SKIM module B Gently remove the SKIM module from a car paying special attention to RF coil see Figure 9 Ts Figure 9 SKIM module P56042298AD B Remove the top plastic cover and unsolder two pins see Figure 10 Figure 9 Unsoldering the pins ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 8 B Locate 24LC02 memory and remove the varnish from the pins by knife or by another appropriate tool see Figure 10 84459251 1 MEALS E E A LI t gt E E gt n gt ma m z ee eee Tw PI Figure 10 Removing the varnish from the pins B Apply the External 12 Volt to the D MAX USB module then connect the SOIC 8 EEPROM Clip cable to the PROG connector see Figure 11 Figure 11 Required connections for the In circuit EEPROM programming B Start the Chrysler SKIM software select the Jeep Grand Cherokee Limited 2000 and press the Read SKIM button see Figure 12 Select Vehicle Vehicle di Read Dadge Nitro Dodge Nitra 12007 OS026071AP 2002 5604527548 2006 S5D4DS55AJ
12. ction is to be used to pogram a New Key Enter the SKIM number If the SKIM numbes is neomeci it val lock the module Press Cancel Operation Button to Cancel operation Press Vakdate Data Button to Start operation Figure 31 Enter the SKIM Number B Shortly thereafter you will see the next screen see Figure 32 ocam an ChSKIM Figure 32 Programming New Key is Successful DMAX 2008 2009 DMAX Automotive Diagnostic Tool 21 11 KEY ERASING VIA THE OBDII This function is only to be used if the owner lost a key and wants to disable all current ignition keys for security reasons This means that all 1gnition keys not only current but also new ones have to be programmed To erase all keys the SKIM number is required Thus read the SKIM number first as described in the Sections 6 and 7 The section 11 describes the operation with the Chrysler SKIM module part number P56010209 AD step by step installed in a 2004 Jeep Wrangler Rubicon Other similar modules could be done in the same manner B Plug In the ODB II Cable and the USB Cable into the DMAX Tool device see Figure 17 Another side of the ODB II Cable has to be connected to the vehicles ODB II connector Make sure that the ODB II LED lights up green Otherwise check the integrity of the OBD II Cable and the OBD II connector B Start the Chrysler SKIM software select the Jeep Wrangler Rubicon 2004 and press the Program a K
13. ector Module Turn lgribice Press Continue Operation Button Read SKIM Figure 19 The SKIM number reading via OBD II ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 13 B Approximately in one minute the software shows the VIN number the SKIM module part number and the firmware version of the SKIM module If the progress bar stays in the marquee mode for more than one minute it means that there is no SKIM module on the J1850 bus detected In this case check if the ignition 1s on and the OBD II cable is connected to the vehicle ChSKIM Joop Wrangler Rubicon 2004 VIM Number _ Number 56010209AD Part Number 5601020340 Version 14 1 Country Code 00 U 5 A Tum Ignition OF Tum n using VALET key Figure 20 The SKIM number reading step 1 B Turn the ignition off Insert the VALET Key and turn the ignition on Approximately in one minute the next screen will appear ChSKIM Help Update About Joop Wrangler Rubicon 2114 VIN Humber Number 5501 UZOSAD Part Number 5601020940 Version 14 Select Vehicle Module Into HER ues MPTY key o Ros Read DTCs Cea DTCs SKMWOUNNES Erara Reve Program a Key Cancel peration Figure 21 The SKIM number reading step 2 ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 14 B Turn the ignition off Insert the EMPTY Key then turn the ignition on Approximately in one
14. ee Figure 17 Another side of the ODB II Cable has to be connected to the vehicles ODB II connector Make sure that the ODB II LED lights up green Otherwise check the integrity of the OBD II Cable and the OBD II connector B Start the Chrysler SKIM software select the Jeep Grand Cherokee Lim 2000 and press the Read DTCs button see Figure 36 7 ChSM zlal xi Jeep Grand Cherokee Lim 2000 Part Humber 55042298AD Select Vehicle Module Info Read SKIM Rigad DTCs DTE SEIM AVOMAYIN Echt Erase Keys este Figure 36 Read Diagnostic Trouble Codes B Turn Ignition On and press the Continue Operation button see Figure 19 B Shortly thereafter the Number of DTCs and DTCs description will appear see Figure 37 ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 24 8 xj update About Part Number 5604 Select Vehicle Module Info Jeep Grand Cherokee Lim 2000 Number of DTCs 47 2298AD FAILURE DTC TRANSPONDER COMM FAILURE OTC SERIAL LINK EXTERMAL FAILURE Read SKIM PCM STATUS FAILURE Read DTCs Clea DTC SKIM WCHUNIN Edi Erase Keys FIRE a kap Figure 37 Number of DTCs and DTCs Description B To erase all diagnostic trouble codes use the Clear DTCs button see Figure 38 zlaj x Jeep Grand Cherokee Lim 2000 Number of DTEs 1 Part Number 55042298AD Select
15. ey button see Figure 33 z iB xj Jeep Wrangler Hubicon 2004 Part Number 55010 209AD Select Vehicle Module Into Read SKIM Read DTC OTC SE OMIA Edi Erasa Keys Program a Key Figure 33 Erase Keys B Turn Ignition On and press the Continue Operation button see Figure 19 B Enter the SKIM number If the SKIM number 15 incorrect it will lock the module at least for 30 minutes Any secured diagnostic operations such as a Read SKIM SKIM WCM VIN Edit Erase Keys or Program a Key will be disabled for 30 minutes B Press the Validate Data button to continue the operation see Figure 34 ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 22 SKIM Figure 34 Enter the SKIM Number B Shortly thereafter you will see the next screen see Figure 35 Figure 35 Erase All Keys Successful ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 23 12 READ CLEAR DIAGNOSTIC TROUBLE CODES DTC This function is implemented to read the diagnostic trouble codes After successful reading the description of every trouble the code displays Also all active and stored trouble codes could be erased This section describes the operation with the Chrysler SKIM module part number 56042298AD step by step installed in a 2000 Jeep Grand Cherokee Lim Other similar modules could be done in the same manner B Plug In the ODB II Cable and the USB Cable into the DMAX Tool device s
16. faces the same way as 24Cxx series EEPROM or 95xxx EEPROM series 2 CHECKLIST AND REQUIREMENTS The following checklist describes what items are supplied with the DMAX Tool and the system requirements if it is used by a DMAX Tool USB device supplied OBD II Cable supplied USB cable supplied SOIC 8 EEPROM Clip with cable supplied Skim Popper Tool See section 13 Optional DMAX Tool software on CD ROM Optional A a A US Desktop Laptop PC and with a free USB Communication Port Power supply 12 Volt 500 mA is used for working out of a car Windows XP Vista with the preinstalled Microsoft NET Framework Ver 3 5 Note To install Microsoft NET Framework Ver 3 5 please download Microsoft NET Framework Version 3 5 Redistributable Package x86 at address http www microsoft com ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 3 3 DEVICE DESCRIPTION The DMAX Tool USB device includes four connectors and two LEDs See Figure 3 12 PC USB connector is intended for communication with the PC See Figure 1 Ext 12 V connector is used when you work on the bench out of a car Apply the 12 Volt 500 mA external power source to Ext 12 V connector paying attention to the polarity Also there are two status LEDs USB is not ready blinking orange USB is ready permanent orange OBD II status shows that the OBD II cable is plugged into the OBD II plug in vehicle green OBD II communication is
17. installed on the PC See section 4 SOFTWARE INSTALLATION for more details B Start Chrysler SKIM software see Figure 8 B Waituntil the USB icon stops blinking B Select the About menu item B Now you can read the USB Module Serial Number and copy it to the clip board loj x Hel Update About USB Dewce Connected Figure 8 Chrysler SKIM software You can download new software form our web site http www autoeltools com Downloading is available for registered users only To get the password you have to provide the valid USB Device serial number and your Email address Once registration process is completed you will receive a password by Email Then you can log in to your account using the password To check if the new software is available B Start Chrysler SKIM software see Figure B Select the Update menu item B Click Check link see Figure 8 1 zlo x Help Update About Select Vehicle USB Device is Connected WEB Ste hip vwww kool New Version ae Figure 8 1 Chrysler SKIM software DMAX 2008 2009 DMAX Automotive Diagnostic Tool 7 6 IN CIRCUIT SKIM READING BY THE CLIP In Circuit reading interface is implemented to work with modules which do not support a diagnostic way to work with the target module Usually this is the first generation of J1850 modules This section describes step by step operation with the Chrysler SKIM module part number 56042298AD installed in
18. minute the next screen will appear ChSKIM _ zlagal x Joop Wranger Rubicon 204 Part Number Part Humber SEO 020940 Tum grubon UH Module Info Tum Ignition On using EMPTY key Figure 22 The SKIM number reading step 3 B Turn the ignition off Turn the ignition on In one minute next screen will appear ChSKIM 181 Help Update About Jeep Wrangler Hubicon 2004 VIM Humber Part Number 56010203 0 Part Number 56010203 0 Select Vehicle Figure 23 The SKIM number reading step 4 Note If you get an error message during the operation try to redo everything from the beginning ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 15 8 THE SKIM NUMBER READING VIA THE OBDII CAN BUS The SKIM reading via the OBD II connector is implemented to work with third generation modules which support a diagnostic way to work with the target module via the CAN protocol This section describes step by step operation with the Chrysler WCM module part number 56040542AN installed in a 2005 Dodge Durango Other similar modules could be done in the same manner B Plug In the ODB II Cable and the USB Cable in to the DMAX Tool device see Figure 17 Another side of the ODB II Cable has to be connected to the vehicles ODB II connector Make sure that the ODB II LED lights up green Otherwise check the integrity of the OBD II Cable and the OBD II connector B Start the Chrysler S
19. nication speed with the target module may take couple minutes on each procedure To work with the J1850 SKIM module the additional two keys are needed The first key is the VALET Key and the second key is EMPTY Key The VALET Key does not have the RF ID chip inside it 1s just a piece of metal The EMPTY Key is the brand new key which was never programmed to any vehicle This section describes step by step operation with the Chrysler SKIM module part number P56010209AD installed in a 2004 Jeep Wrangler Rubicon Other similar modules could be done in the same manner B Plug In the ODB II Cable and the USB Cable in to the DMAX Tool device see Figure 17 Another side of the ODB II Cable has to be connected to the vehicles ODB II connector Make sure that the ODB II LED lights up green Otherwise check the integrity of the OBD II Cable and the OBD II connector Figure 17 Connection of DMAX Tool to vehicle ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 12 B Start the Chrysler SKIM software select Jeep Wrangler Rubicon 2004 and press the Read SKIM button see Figure 18 ChSKIM ED x Help Update About Jeep Wrangler Rubicon 2004 Part Number 5y LET 0209AD Figure 18 The SKIM number reading via OBD II B Turn Ignition On and press the Continue Operation button see Figure 19 ChSKIM Help Update About Jeep Wrangler Rubicon 2004 Part Humber 5501026098AD Plug m OBDII Conn
20. nnection between the DMAX Tool USB device and a vehicle Apply 12 Volt to the Ext 12V connector B Error Message J1850 Output driver Error B Causes This message can appear if the J1850 Driver can not pass the test B Solutions Disconnect the USB cable to reset the DMAX Tool USB device and connect it again If the error message does not disappear please contact the tool distributor for repairing E Error Message J1850 Bus Busy J1850 Bus Error J1850 Check Sum Error J1850 Data Error J1850 Frame Data Error B Causes This message can appear if in time of communication the J1850 protocol error is detected Also the error message could appear if the wrong vehicle type is selected B Solutions Try to initiate the communication procedure again If the error message does not disappear check the DMAX Tool USB device on another vehicle ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 26 E Error Message CAN Initialization Error CAN Reception Error B Causes This message can appear if in time of communication the CAN protocol error 15 detected Also the error message could appear if the wrong vehicle type is selected B Solutions Check the vehicle selection in the vehicle list Try to initiate the communication procedure again Check the DMAX Tool USB device on another vehicle B Error Message Security pass failed B Causes This message can appear if in time of communication the wrong request answer command is issued Also the e
21. rror message can appear if the wrong vehicle type is selected B Solutions Check the vehicle selection in the vehicle list Try to initiate communication procedure again Check the DMAX Tool USB device on another vehicle B Error Message Memory Line is Busy No Response from Memory Memory Reading Error E Causes This message can appear if 1n time of in circuit work via the memory clip the clip was mounted in the wrong direction See Section 6 or the wrong vehicle type was selected B Solutions Pay attention to the Ist pin location see Section 6 for more details Check the vehicle selection in the vehicle list Try to initiate in circuit procedure again Check the DMAX Tool USB device on another memory B Error Message Pin Tester Error s B Causes This message can appear if 1n time of in circuit work via the memory clip the clip was mounted in the wrong direction or pins were not cleaned see section 6 B Solutions Pay attention to the Ist pin location see Section 6 for more details B Error Message SKIM Read Error B Causes This message can appear if in time of communication the J1850 CAN In circuit protocol error is detected Also the error message can appear if the wrong vehicle type is selected B Solutions Check the vehicle selection in the vehicle list Try to initiate the communication procedure again Check the DMAX Tool USB device on another vehicle ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 27 13 T
22. similar modules could be done in the same manner B Plug In the ODB II Cable and the USB Cable into the DMAX Tool device see Figure 17 Another side of the ODB II Cable has to be connected to the vehicles ODB II connector Make sure that the ODB II LED lights up green Otherwise check the integrity of the OBD II Cable and the OBD II connector B Start the Chrysler SKIM software select Jeep Grand Cherokee Lim 2000 and press the SKIM WCMY VIN Edit button see Figure 26 ni x Update About Part Humber 56042298AD Hest inn Read SKIM Read DTCs OTE icd et Edt Erase Keys Program key Jeep Grand Cherokee Lim 2000 Figure 26 The SKIM WCM VIN edit via OBD II B Turn Ignition On and press the Continue Operation button see Figure 19 B Enter the SKIM number If the SKIM number 15 incorrect it will lock the module at least for 30 minutes Any secured diagnostic operations such as a Read SKIM SKIM WCM VIN Edit Erase Keys or Program a Key will be disabled for 30 minutes B Enter a new VIN number It must be the same as a PCM module If you want to bring the module to the unprogramed state leave the VIN field blank The blank VIN number allows you using the Chrysler diagnostic tool to program the VIN number B Enter a new Country Code ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 17 B Pressthe Validate Data button to continue operation see Figure 27
23. to be used to program a new Key To add a new key the SKIM number is required Thus read the SKIM number first as described in Sections 6 7 This section describes step by step an operation with the Chrysler SKIM module part number 56042298AD installed in a 2000 Jeep Grand Cherokee Lim Other similar modules could be done in the same manner B Plug In the ODB II Cable and the USB Cable into the DMAX Tool device see Figure 17 Another side of the ODB II Cable has to be connected to the vehicles ODB II connector Make sure that the ODB II LED lights up green Otherwise check the integrity of the OBD II Cable and the OBD II connector B Start the Chrysler SKIM software select the Jeep Grand Cherokee Lim 2000 and press the Program a Key button see Figure 30 l0j x Jeep Grand Cherokee Lim 2000 Part Number 55042298AD select Vehicle Module Fead SKIM Read DTCs Clear DTCs Erasa Keys Figure 30 Program a Key B Turn Ignition On and press the Continue Operation button see Figure 19 B Enter the SKIM number If the SKIM number is incorrect it will lock the module at least for 30 minutes Any secured diagnostic operations as a Read SKIM SKIM WCM VIN Edit Erase Keys or Program a Key will be disabled for 30 minutes B Press the Validate Data button to continue an operation see Figure 31 ODMAX 2008 2009 DMAX Automotive Diagnostic Tool 20 This lun
Download Pdf Manuals
Related Search