BelAir-Manual - Cactus Bingo Supply
Contents
1. 5 Monitor Audio In Connect the 1 8 inch stereo cable label 5 Monitor Audio In from the back of the computer label 5 in Figure 1 Computer back page 9 into the monitor Plug the cable into the monitors if you want the audio to go to the monitor speakers Note If you want the audio to go to the hall PA system instead of the monitors plug in the 1 8 inch stereo plug from the I O box cable label 8 IO box Audio Out into the back of the computer label 5 in Figure 1 Computer back page 9 12 Bel Air Installation Set up and Configuration Manual October 1 2009 Video King 6 4 PC Video In Cable Figure 5 PC Video In cable shows the PC Video In Cable PC VIDEO IN 14 Figure 5 PC Video In cable The PC Video In Cable cable label 14 PC Video In has an RCA type connector on the end This is typically an RG59 cable with a BNC connector on the end and a BNC to RCA adapter The PC Video In cable plugs into the Video In connector on the back of the computer label 5 on Figure 1 Computer back page 9 Bel Air Installation Set up and Configuration Manual 13 October 1 2009 6 Connector layouts 6 5 PC Video Out Cable Figure 6 shows the PC Video Out Cable PC VIDEO OUT 15 Figure 6 PC Video Out cable The PC Video out Cable cable label 15 PC Video Out has an S Video type connector on the end This is typically an RG59 cable with a BNC connector on the end and a BNC to RCA adapter conn2. B DC In This input connects to the power adapter for the Ball Camera C Focus The control closest to the lens 1s the focus D E White Level Set this to A C for automatic control Zoom The control next to the Focus 1s the zoom Zoom into the ball and then focus it Figure 13 Ball Camera and Ball Chute 24 Bel Air Installation Set up and Configuration Manual October 1 2009 Video King 7 Operating the Bel Air Use the following steps to operate the desk l Turn on the main power switch on the I O Box The electronics will power up Turn on the PC The PowerPlay desk software will automatically start 3 Follow the PowerPlay M User s manual to properly configure the desk software If balls are already on the ball tray press Ball Tray Release button The balls will drop into the ball tray Pull the Ball Chamber release lever The balls will drop into the ball chamber Turn on the blower motor when the session starts If you are using the desk in manual mode you can use the Motor switch on the I O Box to turn on the blower motor Once the bingo session begins remove the balls from the Ball Chute and place the balls in the Ball Tray until a bingo 1s called Refer to the PowerPlay M User s manual for details on running a session When the desk is no longer required for play shutdown the PC and turn off the I O Box Bel Air Installation Set up and Configuration Manual 25 O
3. Dec 18 2008 Brackets Item No s 36 and 37 changed JJL BOM updated June 23 2009 E Mounting bracket configuration changed JJL Components added Drawing and BOM updated Sep 3 2009 Ball chamber material changed JJL DETAIL A STEP 1 BASE i mai DESIGN DATE TITLE ASSEMBLY INSTRUCTIONS This drawing is the exclusive property of 7 04 05 DELE MURDER pop Video King Gaming amp Entertainment and DATE 4 17 07 SERIES 600 GAMING DESK TOLERANCES FOR XXX 010 all rights are reserved No part of this NONLIMITED DIMENSIONS FN drawing may be used or reproduced in DATE 1 17 07 scALE FILE No REV No E any manner whatsoever without written we TE 2 any manner whatsoever wthoutwriten GAMING amp ENTERTAINMENT DATE NTS 18PPlay600 3D dft F Entertainment DWG No Outsource File No SHEET 18PPlay600 3D 25902 115 dft 1 of 18 Bel Air Installation Set up and Configuration Manual Appendix Motor Replacement 10 ex ex 13 x i I Nu VO amp 40 i1 T 10 Cr RN pee T pet R UT eeu ag AME IR 13 WD STEP 2 FRAME ASSEMBLED STEP 2 FRAME I NTS 18PPlay600 3D dft F 18PPlay600 3D 25902 115 dft 38 Bel Air Installation Set up and Configuration Manual October 1 2009 wideoMing 15 a ea ES x STEP3A FRAME Ye T jt Le b Note that counterbore i holes face upward inr jf m E A
4. Wie leo King Bel Air Installation Set up and Configuration Manual October 1 2009 Document history Date October 5 2007 April 9 2008 Oct 28 2008 Oct 30 2008 Apr 30 2009 Jun 24 2009 Sept 4 2009 Oct 1 2009 Prepared by Holly Steele Terry Lowdon Gord Boyechko Gord Boyechko Gord Boyechko Gord Boyechko Gord Boyechko Gord Boyechko Description Made the following changes Updated manual to include new cable labels Updated sections 1 6 8 and 9 Added the hardlock to the wiring diagram section 13 Included the cable label matrix section 12 Reformatted the document to make 1t easier to read and navigate Updated the part number for the Pyramid Display UL AC cord Warning Series 11 PC connections UL AC Receptacle Notice Cable labels Ball rail brackets Service address Ball chamber material Replace motor instructions Bel Air Installation Set up and Configuration Manual October 1 2009 Important Notice This guide is delivered subject to the following conditions and restrictions This guide contains proprietary information belonging to Video King Such information 1s supplied solely for the purpose of assisting explicitly and properly authorized users of the Bel Air system e No part of its contents may be used for any other purpose disclosed to any person or firm or reproduced by any means electronic or mechanical without the express p
5. Set up and Configuration Manual October 1 2009 Video King 3 Installing the console The Monitor and PC must be installed into the console and connected as described in Connector Layout section of this manual All other components are pre assembled Depending on if a right hand or left hand operation desk is ordered the monitor will be installed accordingly The bingo balls are placed in the blower chamber by opening the door at the back of the ball chamber Bel Air Installation Set up and Configuration Manual October 1 2009 4 Electrical installation 4 Electrical installation Plug the console AC power cord into a 115VAC 60Hz outlet The main AC power input to the Bingo Console should be 1 15VAC 60Hz The power outlet or power cord to the Bingo Console should be wired with 12A WG or 14AWG with ground The AC power input circuit must be rated for at least ISA and no other hall equipment should share this power source Do not run long extension cords with inadequate wire gauge from the power source to the console The main AC power input may be optionally plugged into an Uninterruptible Power Supply UPS to provide power backup in the event that main power is lost The desk and all its components have a typical maximum power draw of 850W with the blower motor running Caution A power source with abnormal voltage or excessive noise can result in improper console operation and possible damage not covered under warrant
6. Set up and Configuration Manual 15 October 1 2009 6 Connector layouts 6 7 Video Switch Front Figure 8 shows the video switch front Power Bingo King Video Switch A A OUT OUT OUT 3 rE Cui ON E a A AA Since A vs j QV CON NECT c Figure 8 Video switch front The following connections indicators and switches can be found on the front of the Video Switch IN 1 4 These inputs are for external video They are typically not used in a standalone desk configuration OUT 1 3 These outputs are used for connection to hall monitors PWR ON This LED indicates that the Video Switch has power This light will not come on until you start PowerPlay SETUP REQ D This LED indicates that the Video Switch has not been setup yet and is using the default settings CONNECT This LED indicates that the Video Switch has a TCP IP connection RESET This push button switch is used to reset the Video Switch 16 Bel Air Installation Set up and Configuration Manual October 1 2009 Video King 6 8 Wired Network Switch Back Figure 9 shows the wired network switch back NETWORK SWITCH POWER 16 P NETWORK NETWORK NETWORK WITCH LAN 1 SWITCH LAN 2 SWITCH LAN 3 17 12 18 2 A Figure 9 Wired network switch The switch shown in the photo is a typical switch used and the actual switch used may vary Make the following connections to the Network Switch 16 Network Switch Power Plug the DC
7. Video King STEP 18 FILTER LABELS DOOR NOT SHOWN FOR CLARITY NTS 18PPlay600 3D dft STEP 18 FILTER LABELS ASSEMBLED F 18PPlay600 3D 25902 115 dft semel 53 Bel Air Installation Set up and Configuration Manual Appendix Motor Replacement 1 Items 96 thru 104 are not shown in any illustration Refer to the wiring diagram REV No 18PPlay600 3D dft DWG No Outsource File No SHEET F 18PPlay600 3D 25902 115 dft 18 of 18 item JDescripton SCS Sent Part No ay item Description SCC Client Part No ay 1 BOTTOMPANEL LLL fenon i 87 WOOD SCREW PANHD PHILLIPSS8x050LG BLACKOXIDE fieoooo2zsA 4 2 jCASTER SWVEL LLL reorooo 3 68 BALLSTOPCHROME LL Jroosutis 1 3 CASTER SWIVEL LOCKABLE t60700054 2 69 jPRYOUTPLUG I4ID BLACK 16070039 4 3 4 LOCK WASHER SPRING 5 1610 160000214 20 70 THICK PANEL DOME PLUG 7 8 10 BLACK 16070034444 1 s LAG SCREW 5 16 x 1 1 2 LG H6000020 A 20 71 SCREW MACHINE PAN HD PHILLIPS 10 24 x0 75LG BLACK OXIDE 16070013 4 6 BLOWER DOOR ASSEMBLY fesos i 72 MOUNTING BRACKET MONITOR 160800234 1 7 WOODSCREW PANHD COMBO38x075l1G ZINCPLTD 160700254 9 73 SCREW MACHINE PAN HD PHILLIPS 10 24 x2000LG ZNPLTD 160700284 4 8 ROTARY CATCH LARGE Teosa 4 74__ NUT WINGfIO 24UNC ZINCPLTD 60700304 4 79 __ WOOD SCREW PAN HD
8. Cable label malrix ooi con dc d gu a ER ee loo dust suu deu vu dieu C ds 31 Um prr me 32 14 Technical Specifications oor cione neon xr Caen aaa aua v et aaa 33 Appendix Exploded assembly drawings and bill of material 35 Appendix Motor HeplacemieHhl 5 22 52 22 91 2 585 i a eEe Pic nea 2c Ens aeo E ss ein see ge Pss a Ee tans 55 Bel Air Installation Set up and Configuration Manual iii October 1 2009 1 Introduction 1 Introduction Video King is proud to introduce the PowerPlay Bel Air the most contemporary high tech bingo console on the market today The wave of the future our latest generation of bingo consoles with a sleek new design has all the ultimate features bingo hall operators are looking for In essence the best of both worlds as far as form and functionality have been merged and transformed The PowerPlay Bel Air is e Softly contoured e Easy to service e Quiet to run e Fully loaded with all the latest software All these attributes make Bel Air North America s number one choice in bingo consoles sea s ng dix Rr d tT 3 rt m Nu i 1 oo N L B o S Bel Air Installation Set up and Configuration Manual October 1 2009 1 Introduction Standard Features Touch screen flat panel monitor with built in speakers Slant top design for caller comfort PC technology Window
9. IO Box Audio In Connect the RCA plug cable label 9 IO Box Audio In to the back of the I O Box from the computer This is a pass through connection 10 IO Box Mic In Connect the 4 inch phono plug cable label 10 IO Box Mic In to the back of the I O Box from the computer 22 Bel Air Installation Set up and Configuration Manual October 1 2009 Video King 11 IO Box Modem Connect the RJ11 plug cable label 11 IO Box Modem to the back of the I O Box from the computer This is a pass through connection 12 IO Box LAN Connect the RJ45 plug cable label 12 IO Box LAN to the back of the I O Box from the Network Switch This 1s a pass through connection 13 IO Box Printer Connect the DB25 parallel cable cable label 13 IO Box Printer from the computer to the back of the I O Box This 1s a pass through connection Motor Switched Connect the blower motor to this connector This output is controlled by the I O Box firmware and the IO Box Motor front panel switch AC Out Switched Connect the Power Block to this connector This output is controlled by the I O Box master on off switch Bel Air Installation Set up and Configuration Manual 23 October 1 2009 6 Connector layouts 6 12 Ball Camera Figure 13 shows the Ball Camera and Ball Chute The following connections and controls are found on the Ball Camera A Ball Camera Video This output connects to the video switch not shown on diagram
10. Pin DIN DB9P RCA Plug RCA Plug 1 Phono Plug RJ11 RJ45 DB25S BNC BNC RJ45 RJ45 BNC Label Monitor VGA Monitor DC 12V Monitor TOUCH IF PC Audio Out Master Panel IO Box IO Box Serial IO Box Audio Out IO Box Audio In IO Box Mic In IO Box Modem IO Box LAN IO Box Printer Video Switch OUT 4 Video Switch IN 5 Video Switch Network Network Switch LAN 3 Video Switch IN 6 13 Wiring diagram iagram d 13 Wiring Campuler Keyboatd C 0 Maus Q Computer Rear HlHAardiock Adagio QAD No 15130002 4 Computer Honor Flourescent Lamp ID Power Block Master Panel Assembly O00000000000000 000000000000900 000000000009000 000000000000000 OOO000000000000 Ribbon Cable Video Switch IF ront Power Braga eg esi Sat k Vien Sith Rear Ad A 0 00 000 QE 75 ohm ONG Male Lo Male RGBA DAD No 16842902 A T8 ohre ANG Hale to Malis RGA Video 4 QAO No 16840002 Camera GAD Na 16840003 A Extension Cond QAD Mo 16370001 A B UO Hox Rear GAT Se LAN Cable OAD No 16840001 4 32 19 Box Front 8968 06 C Jog caco pd Kag to 115VAC 15A Network Hub Rear Bel Air Installation Set up and Configuration Manual October 1 2009 Video King 14 Technical Specifications Length 58 25 inches Width 29 inc
11. SLOTTED 4x 500lLG fieorooora 32 75 COVER BALL RAIL BRACKET esona 2 l L dt 2 76 PYRAMIDDISPLAY lt memo i ai center Brace lt Teos i 77 OPEN CLOSED UNIVERSAL BUSHING 1 1 2 ID BLACK i6000014A 1 12 DOWEL WOOD GROOVED 0250DIA x151G 160700094 12 78 WASHERPLAN4MZINCPLTD i60001 amp A 4 13 CROSSDOWEL 220UND t60700018A 3 79 WASHER SPRING LOCK 4mm ID ZING PLTO 18000017 wx 14 WASHER FLAT 375 ID x 875 OD x 104 THK STEEL BLACK LUSTERFINISH 160700334 14 80 MACHINE SCREW PHILLIPS PAN HD M4 0 0 7P x 12LG ZINC PLTD 16000019 A 4 15 JOINTCONNECTORBOLT 1 4 20UNCx27500 G 160700204 33 81 j 5PORTLINKSYSNETWORKSWITCH o o 351 16 MIDPANEL fe ooo4D 1 82 VDEOSWTCH 17 BLOWER ENCLOSURE ASSEMBLY fesomss 2 83 OBOXASSEMBLY T LT 18 WOOD SCREW PAN HD COMBO 10x 100LG ZINCPLTD i16070015A 41 84 COMPUTER 500 SERIES KEYBOARD MOUSE Ba 19 JOINT CONNECTOR BOLT 1 4 200NC x20000G i6070019A 4 85 SIDE ACCESS PANEL ASSEMBLY 7 EAR 20 BRACKET QUARTER TURNFASTENER 16000108 2 ral 21 QUARTER TURNFASTENER LL ieooita 4 787 WINDOW LLL f 6070003 A a 22 BALLCHAMBER LLL meorB 19 F es FRONT SHIELD ASSEMBLY fies3008 CE 23 _ WAS
12. barrel plug cable label 16 Network Switch Power into the back of the Network Switch The voltage and rating of the power input is labeled on the back of the switch Ensure the correct mating AC to DC power adapter is used to match voltage and current 17 Network Switch LAN 1 Insert the RJ45 LAN cable cable label 17 Network Switch LAN 1 from the Video Switch into port 1 of the Network Switch 12 Network Switch LAN 2 Insert the RJ45 LAN cable cable label Network Switch LAN 2 from the I O Box into port 2 of the Network Switch Network Switch LAN 2 is a pass through LAN connection to the external Local Area Network 18 Network Switch LAN 3 Insert the RJ45 LAN cable cable label 18 Network Switch LAN 3 from the PC into port 3 of the Network Switch Bel Air Installation Set up and Configuration Manual 17 October 1 2009 6 Connector layouts 6 9 I O Box Front Figure 10 shows the I O Box front rJ E d Out Mic In B i Tees Bonanza Autocom Network Modem Se T Reset Video King I O Control Panel MASTER ON OFF SWITCH 120VAC Figure 10 IO Box front The IO Box Front panel makes user connections easily accessible The following connections Status and controls are available of the front of the I O Box Line In L R Stereo Left and Right Audio inputs are provided This input is mixed with internal audio and fed to Audio Out Audio Out L R Stereo Left and Right Audio out is provided for exter
13. ea y TP DETAIL B UT IT 9 STEP 3B FRAME i Jd NTS 48PPlay600 3D dft STEP 3 FRAME ASSEMBLED mW Outsource File No SHEET 18PPlay600 3D 25902 115 dft 3 of 18 39 Bel Air Installation Set up and Configuration Manual Appendix Motor Replacement Before assembly paint the outside metal surfaces with fast dry gloss black enamel paint EN 4 sides 105 106 107 108 H BLOWER TRAY SUB ASSEMBLY 25 DETAIL C STEP 4 BALL CHAMBER uu I DOOR NOT SHOWN FOR CLARITY o NTS 18PPlay600 3D dft F 40 Bel Air Installation Set up and Configuration Manual October 1 2009 Video Kin STEP 5 LAMP ASSEMBLY gam lion p SS 29 98 i 20 ZTP E om MN P t Fi pens bed m 8 E i i Lrg STEP 6 TABLE TOP SUB ASSEMBLY at DETAIL E SCALE FILE No REV No Boecl PL nts 18PPlay600 3D df DETAIL D DWG No Outsource File No SHEET E 18PPlay600 3D 25902 115 dft 5 of 18 41 Bel Air Installation Set up and Configuration Manual Appendix Motor Replacement z5 Us STEP 7 TABLE TOP ASSEMBLY STEP 7 TABLE TOP ASSEMBLED NTS 8PPlay600 3D dft 18PPlay600 3D 95902 115 dft 6 of 18 42 Bel Air Installation Set up and Configuration Manual October 1 2009 Video King m x STEP 8 UPPER BRACKETS ASSEMBLED SCALE FILE No REV No STEP 8 UPPER BRACKETS o Tm ae ea A DWG No Outsour
14. turned on at the front of the computer 120 VAC This connector supplies power for all internal Desk components Bel Air Installation Set up and Configuration Manual 19 October 1 2009 6 Connector layouts 6 10 I O Box External Cables Figure 11 shows the external cables from the I O Box E ZSMASTER PANEL IO BOX IIO BOX SERIAL 7 BIO BOX AUDIO OUT Sell r 10 BOX AUDIO IN 9 e IO BOX AUDIO IN 9 Ll klO BOX MIC IN 10 Ra IO BOX MODEM 11 IIO BOX LAN 2 12 un EO BOX PRINTER 13 Figure 11 I O Box external cables Connect the following cables from the I O Box to the Computer Master Panel 6 20 Master Panel IO Box Plug the 26 pin DIN connector from the back of the IO Box cable label 6 Master Panel IO Box into the Master Panel IO Box Serial Plug the DB9 serial cable from the I O Box cable label 7 IO Box Serial into the I O box serial port label 7 in Figure 1 Computer back6 1 Computer Back diagram page 9 on the back of the computer label 7 on Figure 1 Computer back page 9 8 IO Box Audio Out Plug the 1 8 stereo plug cable label 8 IO Box Audio Out from the I O Box into the Audio Out jack label 5 in Figure 1 Computer back diagram page 9 on the back of the computer Cable label 8 1s not depicted in Figure 1 Computer back diagram page 9 because cable label 5 is plugged in Plug the cable from the PA system into the I O box if you want the audio to go to the ha
15. 00000 6 11 Wired IO Box Back Figure 12 shows the wired I O Box back J i I E fn IO BOX x d PRINTER 13 llO BOX SERIAL 7 Y IO BOX IN MASTER PANEL I O BOX 6 IO BOX LAN 12 i MODEM 11 y d if AN 1 E 7 i E E 5 i r E Z5 j i J i x E F y d z d j E f d j i J HU j Motor AC Out e F i j j i i F F j i Jl FE P J lj F ail al i e F Ji i F j j j j F d r i i j r E i i i 5 d 1 J Fiqure 12 Wired IO Box back Make the following connections at the back of the IO Box 6 Master Panel IO Box Connect the 26 pin DIN connector cable label 6 Master Panel IO Box from the Master Panel to the back of the I O Box 7 IO Box Serial Connect the DB9P cable cable label 7 IO Box Serial from the computer to the back of the I O Box 8 IO Box Audio Out Connect the RCA plug cable label 8 IO Box Audio Out to the back of the I O Box from the computer This is a pass through connection Cable label 8 is not depicted in Figure 1 Computer back diagram page 9 because cable label 5 is plugged in Plug the cable from the PA system if you want the audio to go to the hall PA speakers Note If you want the audio to go to the monitor speakers instead of the hall PA system plug the 1 8 inch stereo plug from the monitor cable label 5 Monitor Audio In into the back of the computer label 5 in Figure 1 Computer back page 9 9
16. 2 115 dft 11 of 18 F Appendix Motor Replacement e R0 oe cc aaa 78 79 80 23 v STEP 13 MONITOR as NTS 18PPlay600 3D dft STEP 13 MONITOR ASSEMBLED DWE Ne Outsource Fe No Fl 12 of 18 48 Bel Air Installation Set up and Configuration Manual October 1 2009 Video King DETAIL G ere ae ies DETAIL H Note orientation of lock cylinder for Right Side Panel Assembly shown Rotate cylinder 180 for Left Side Panel Assembly STEP 14 SIDE PANEL SCALE FILE No REV No nts tap Piayo0o 30 d DWG No Outsource File No SHEET F 18PPlay600 3D 25902 115 dft 13 of18 STEP 14 SIDE PANEL 49 Bel Air Installation Set up and Configuration Manual Appendix Motor Replacement 87 86 f y STEP 15 FRONT FACE DETAIL I d NTS 18PPlay600 3D dft F 14 of 18 50 Bel Air Installation Set up and Configuration Manual October 1 2009 Video King STEP 16 SHIELD Ye v DETAIL J SCALE FILE No REV No ISS No DWG No Outsource File No SHEET F 18PPlay600 3D 25902 115 dft 15 of 18 51 Bel Air Installation Set up and Configuration Manual Appendix Motor Replacement STEP 17 ENCLOSURES ASSEMBLED STEP 17 ENCLOSURES SCALE FILE No REV No DWG No Outsource File Na SHEET F 18PPlay600 3D 25902 115 dft 16 of18 52 Bel Air Installation Set up and Configuration Manual October 1 2009
17. 270 Pacific St Omaha NE 68114 5429 30 Bel Air Installation Set up and Configuration Manual October 1 2009 12 Cable label matrix Device PC Monitor Monitor Power Supply PC Monitor Master Panel PC PC PC PC PC Network Switch PC PC PC Network Switch Power Supply Network Switch PC Ball Camera Ball Camera Power Supply Video Switch Bel Air Installation Set up and Configuration Manual October 1 2009 From Connector DB15P DC Plug DC Jack DB9S 1 8 Stereo Plug 26 Pin DIN DB9S 1 8 Stereo Plug 1 8 Stereo Plug 1 8 Plug RJ11 RJ45 DB25P BNC to RCA S Video DC Plug RJ45 RJ45 BNC DC Plug DC Plug Label PC VGA Monitor Power Monitor Power PC Touch Screen Monitor Audio In Master Panel PC IO Box Serial PC Audio Out PA PC Audio In PC Mic In PC Modem Network Switch LAN 2 PC Printer PC Video In PC Video Out Network Switch DC Power Network Switch LAN 1 PCLAN Ball Camera Ball Camera DC Power Video Switch DC Power Label Number 1 2 3 10 11 12 13 14 15 16 17 18 19 20 21 Video King Device Monitor Monitor Monitor PC IO Box IO Box IO Box IO Box IO Box IO Box IO Box IO Box Video Switch Video Switch Video Switch Network Switch Video Switch To Connector DB15P DC Plug DB9P 1 8 Stereo Plug 26
18. CKETASSEMBLY BALLRAIL RIGHT 163300224 e D E 102 BINGOBALLS TITAN BEST MULTI 75 ST F 8373014 2433 i 37 BRACKETASSEMBLY BALLRAIL LEFT lt 163300214 te A 103 POWERBLOCK notshown SS CSCS 38 BRACKET SHAPED ADAPTER BALLRAIL 163300204 2e D E 104 75 ohm BNC MALE TO MALE RG 59 CABLE 168400024 2 39 DEFLECTOR 60500224 T1 T OTOH EASE ASSY METAL OF OAM OIM EN 40 COLLECTORTRAY C 180500208 i 194 MOTOR WIPLUG FOO at T17 41 JBALL CHAMBER BACKFACE ASSEMBLY ie3300078 i OCK WASHER INT 10 ZP 10251010 4 742 CAMLOCKwi2KEYS LLL uoskot fa i CREW MACHINE FIG Oa eT BIL BIO FF 63823 47 43 MASTERPANELASSEMBLY 73405 1 44 SCREW MACHINE PAN HD PHILLIPS 10 24 x 0 375LG BLACK OXIDE 160700124 4 45 THREADED ROD 8 32UNC x2 1 2LGSTEELZNCPLID 16000007 1 46 SPACERALUMNUMPLAN i600000 amp 4 i 47 KNOBCHROMEsS832UNC fomo 2 48 BRACKET ARMREST 170557 12 49 PADARMRESTPOWERPLAY roseo 2 50 lACTUATORCONTROL TRAPDOOR 160500248 i 51 RODCGUP o o feoroo2 a dt 52 CAMERA PANEL LLL fieocoz i 753 ROTARY CATCH SMALL LLL reozoo274 a 54__ WASHER RUBBER NEOPRENE AID fisooozsa 5 55 BA
19. HER FLAT 10 x 500 OD STEEL ZING PLTO i6070017A io 9 ROD SIDE PANEL HINGE LLL fieosozsa 2 24 SCREW MACHINE PAN HD PHILLIPS 8 32UNC 0 375LG BLACK OXIDE 160700144 309 E 90 lIRFLTER LLL 0300024 1 25 BACKFACEASSEMBLY C TfesoweB 2 91 JARFITERRETANER 330194 1 26 MOTOR BASE ASSEMBLY METAL 003376832 i 92 THICK PANEL DOME PLUG 1 1 2 10 BLACK 16000064 1 27 STRAIN RELIEF BUSHING HEYCO SR6P34 1607000889 2 93 HPCUTVINYLZICOLORVIDEOKNG Ti044D amp 00A 1 28 kNOCK OUTADAPTER HEYCOA25F i60000012A i 94 HPCUTVINYLZ COLORDECAL POWERPLAY i044D601A 1 29 AMPASSEMBLY lt lt lt 1708001 1 95 JHP CUT VINYL 2 COLOR DECAL BELAIR Ysa BOD 1 730 CORD 120 VAC 15 AMP_2W GRNO 6 FT rooted 96 TILT MONITOR STAND OPTIONAL 637000684 1 31 GROMMET 5 16 ID 9 16 OD 1 16 PANELTHK i6000015A 1 97 RIBBON CABLE ASSEMBLY fesoa i s2 TOPPANEL LLL ieooooe i o8 B CAT 5e LAN cAaBLE lt lt fesoa 2 33 BULB FLOURESCENT WHTE joa i 99 NTSC CAMERA DC ADAPTER FOR SONY ExView fiesrooosa 1 34 accessory she 10500274 3 100 BNCFEMALE TOPHONOPLUG fema i 35 STRIKER 1 ooo 2 A A Caor EXTENSION CORD wGROUNDEDPRONG 6FT ferooma 1 36 BRA
20. LTUBE ES 1 56 GASKET BALLCHUTE 6030000344 Si 57 BALLCHUTERETANER i05000 9A i 58 BALLCONE foo 1 59 HEX HEAD BOLT 1 4 20UNC X 2 LG GRSZINCPLTD 160000234 i 60 NUT HH 1 4 20UNC GR2 ZINC PLTD 16000022 A t 61 WASHER PLAIN 1 4 ID ZINC PLATED 16000024A 1 62 NTSCCAMERA C fieszooos8 1 763 NTSCCAMERA AUTOIRISLENS C fie370008A i SCALE 764 UNIVERSAL BUSHING 7 8 HOLE DIA BLACK 16000027 1 NTS es BALLCATCHPLATE O eooo i 66 BALLCATCHBLACKVNYL uot r 54 Bel Air Installation Set up and Configuration Manual October 1 2009 Appendix Motor Replacement Step 1 Remove Ball Release Knob This 1s only hand tightened so no tools should be necessary Step 2 Remove screws from the Master Panel There are 4 Phillips screws 2 on each side 55 Bel Air Installation Set up and Configuration Manual Appendix Motor Replacement Step 3 Remove the Master Panel Pull the Master Panel up and out and disconnect the 26 pin ribbon cable on the right hand side Step 4 Loosen the Screws on the black Ball Deflector Only loosen the 3 screws on the deflector The Ball Door Assembly slides underneath the deflector so the tension will have to be released m En 56 Bel Air Installation Set up and Configuration Manual Video King Step 5 Remove the Ball Release Lever Use a flat head screwdriver or needle nose pl
21. NTINGENT ON THE PROPER USE OF THE PRODUCT IN ACCORDANCE WITH THE INSTRUCTIONS AND SPECIFICATION PROVIDED BY MANUFACTURER AND SHALL NOT APPLY TO ANY PRODUCT THAT HAS BEEN REPAIRED OR MODIFIED BY PERSONS OTHER THAN MANUFACTURER OR IF USED IMPROPERLY OR IN AN OPERATING ENVIRONMENT NOT APPROVED BY MANUFACTURER IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR ANY SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RELATING TO THE USE OF THE PRODUCT OR FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESSED OR IMPLIED WHATSOEVER This warranty DOES NOT cover any items that are in one or more of the following categories software devices external to the original system such as but not limited to printers monitors etc except specifically noted accessories or parts added to a system by Video King after the system is manufactured and accessories or parts that are not installed at the Video King factory Any items not covered by this warranty are covered solely by a warranty offered by the manufacturer s of the item s Computer keyboards and mouse units are included as part of the system and are covered under this warranty This warranty DOES NOT cover damage due to external causes including but not limited to accident abuse misuse problems with electrical power servicing not authorized by Video King usage not in accordance with product instructions failure to perform required preventative maintenance or problems caused by use of parts or components not
22. able label 14 PC Video In from the Video Switch into this connector PC Video out Plug the S Video cable cable label 15 PC Video Out from the Video Switch into this connector Video out goes to the hall monitors PC LAN Plug the RJ45 Local Area Network cable cable label 18 PC LAN from the Network Switch into this connector Bel Air Installation Set up and Configuration Manual 10 October 1 2009 Video King 6 2 Monitor External Cables Figure 3 shows the external cables from the monitor P BMONITOR POWER E PLUG 2 PC TOUCH SCREEN 4 MONITOR x POWER JACK ANO Pa Ud 220 3 7 o Figure 3 Monitor external cables Connect the following cables to the computer from the monitor 1 PC VGA Connect the DB15 VGA cable cable label 1 PC VGA to the blue monitor input at the back of the computer label 1 on Figure 1 Computer back page 9 Do not connect the PC VGA to E See Figure 1 Computer back page 9 as this VGA connector is disabled 2 Monitor Power Plug Connect the DC plug cable label 2 Monitor Power Plug into a DC barrel jack cable label 3 Monitor Power Jack from the Monitor Power Supply 3 Monitor Power Jack A 100 240 VAC 50 60Hz to 12VDC 4 164 adapter is used to power the Monitor Connect the DC Jack cable label 3 Monitor Power Jack to the Monitor Power Plug cable label 2 Monitor Power Plug 4 PC Touch Screen Connect the DB9 serial connector cable label 4 PC Touch Screen to
23. acking installation set up and servicing of the console For operation of the bingo console and e BOS software please see our PowerPlay User s manual and e BOS Utilities User s Manual Bel Air Installation Set up and Configuration Manual 3 October 1 2009 2 Unpacking the console 2 Unpacking the console Inspect the shipping containers for possible signs of damage If damage is detected call the carrier to make a claim Use a box cutter to cut the straps from the skid taking care not to damage the console With the help of at least one assistant carefully slide the console from the skid and place it on the floor Remove the cardboard top Remove the foam packing inserts from inside the top and slide the cardboard tube up and off the console A minimum of two people are required to safely unpack the console With one person lifting from each end of the console raise the console up and out from the carton and foam inserts Check that all casters are in place Do not destroy or discard carton or packing material until after final inspection and testing Unpack the keyboard from the cardboard box Place the keyboard on the electronics cabinet in front of the touch screen monitor Remove the mouse from the plastic bag and set next to the keyboard At this point you should inspect the consoles for any obvious shipping damage If any problems are found immediately contact your distributor for advice 4 Bel Air Installation
24. anty repairs and building replacement products If Video King repairs or replaces a product the replacement product will carry a 60 Day warranty from the date of receipt by customer of the repaired or replaced product from Video King Depending upon availability replacement products may not be identical but will be equivalent to or better than the original product NOTE Before Video King repairs the product s it is the customer s responsibility to back up all computer data and software on the hard disk drive s and any other storage devices s 1n the product s and to remove any removable media such as diskettes CD s etc It 1s also the customer s responsibility to reload data and software after the repairs have been completed Video King is not responsible for any loss of data or software and Video King is not required to advise or remind the customer of appropriate backup security and procedures Warranty restriction and limitations The following items carry a 90 Day warranty only from the original invoice date All Bingo Balls Blower Motor Air Filter Part No 16030002 A Blower Motor Part No 10337110 Bel Air Installation Set up and Configuration Manual 29 October 1 2009 11 Service 11 Service For Warranty Service or to obtain an RMA Number call 1 888 246 4609 8 00am to 4 30pm CST Monday thru Friday Note Shipping cut off time 1s 3 00pm Monday thru Friday For Equipment Returns ship to Video King 7
25. ce Fie No SHEET E 18PPlay600 3D 25902 115 dft 7 of18 43 Bel Air Installation Set up and Configuration Manual Appendix Motor Replacement s MAE Note orientation of lock DETAIL F Nts 8PPlay600 3D dft FILE No _ NIS ISPPlay600 D df 48PPlay600 3D 25902 115 df 8 of 18 44 Bel Air Installation Set up and Configuration Manual October 1 2009 Video King STEP 10 MASTER PANEL ASSEMBLED 24 STEP 10 MASTER PANEL SCALE FILE No REV No Slide panel up behind Item 40 T NTS 18PPlay600 3D dft DWG No Outsource File No SHEET F 18PPlay600 3D 25902 115 dft 9 of 18 45 Bel Air Installation Set up and Configuration Manual Appendix Motor Replacement ivt ese s na eee E e cr NN g Nn c dis EM A m i a 52 7 e 19 STEP 11 CAMERA TOP SUB ASSEMBLY ae NIS eese apat 18PPlay600 3D 25902 115 df 40 of18 of 18 46 Bel Air Installation Set up and Configuration Manual October 1 2009 Video King O Oo N ag b D l 77 e5 th T4 oat TO 4 tt 69 O Jo at W da MEER E Q Co 113 A p o x MI T il STEP 12 CAMERA TOP ASSEMBLY 47 Bel Air Installation Set up and Configuration Manual STEP 12 CAMERA TOP ASSEMBLED DWG No 18PPlay600 3D Outsource F SCALE FILE No NTS 18PPlay600 3D dft ile No SHEET 2590
26. ctober 1 2009 8 Servicing and cleaning 8 Servicing and cleaning The following serviceable items require regular maintenance The blower motor requires oiling every 6 months using SAE20 oil The blower motor can be accessed through the blower motor door Failure to regularly oil the motor may void motor warranty The blower motor air filter should be cleaned every 6 months using water and dish soap The air filter can be accessed through the blower motor door The stainless steel front panel of the desk can be cleaned using Trans Mate Gold Series cleaner or any other suitable stainless steel cleaner When cleaning the stainless steel ensure you wipe with the grain General cleaning of surfaces may be done using mild dish soap and water The Fan on the inside of the PC should be cleaned using a small hand vacuum every 6 months In the event that the ball chamber lamp burns out it may be access through the ball chamber The replacement bulb part number is 1708L001 If bingo balls become damaged a new set of balls may be ordered using part number 6373014 43 26 Bel Air Installation Set up and Configuration Manual October 1 2009 9 Troubleshooting Video King The following are some typical problems and the solutions The following are some typical problems and the solutions Problem Electronics and desk have no power Ball action in chamber is irregular e g balls are sticking Ball image is fuzzy too sma
27. e letters refer to the unlabeled cables A B C D 10 11 13 14 15 18 120 VAC Connect the AC receptacle to the Power Block PS 2 Keyboard Connect the PS 2 keyboard to this port The connector is typically green PS 2 Mouse Connect the PS 2 mouse to this port The connector is typically purple Hardlock Connect the USB hard lock it to a standard USB port If you have a parallel hard lock connect it to a parallel port PC VGA Connect the DBI5P VGA connector cable label 1 PC VGA from the Monitor into this connector PC Touch Screen Plug the DB9 serial connector cable label 4 PC Touch Screen from the Touch Screen Monitor into this connector Monitor Audio In Plug the 1 8 stereo plug cable cable label 5 Monitor Audio In into this connector The connector is green PC IO Box Serial Connect the I O Box DB9P serial cable cable label 7 PC IO Box Serial to this port PC Audio in Plug the 1 8 stereo plug cable label 9 PC Audio In into this connector The connector input is blue PC Mic in Plug the 1 8 stereo plug cable cable label 10 PC Mic In into this connector The connector input is red PC Modem Connect the RJ11 plug cable label 11 PC Modem from the I O Box into this connector PC Printer Connect the DB25P pass through printer cable cable label 13 PC Printer from the I O Box to this port PC Video in Plug the RCA phono plug c
28. ected to a RCA to S Video adapter The PC Video Out cable plugs into the Video Out connector on the back of the Computer label 15 on Figure 1 Computer back page 9 14 Bel Air Installation Set up and Configuration Manual October 1 2009 Video King 6 6 Wired Video Switch Back Figure 7 shows the wired video switch back Figure 7 Wired video switch back Make the following connections to the Video Switch 14 15 17 19 21 Video Switch Out 4 Connect the BNC video output cable label 14 Video Switch Out 4 to the PC Video In input on the computer label 14 in Figure 1 Computer back6 1 Computer Back diagram page 9 Video Switch In 5 Connect the BNC video input to the PC Video Out input on the back of the computer label 15 in Figure 1 Computer back diagram page 9 Video Switch Network Connect the RJ45 LAN connection cable label 17 Video Switch Network to the Network Switch Video Switch In 6 Connect the BNC video output cable label 19 Video Switch In 6 to the Ball Camera Video Switch DC Power Plug the DC barrel plug cable label 21 Video Switch DC Power into the back of the Video Switch The voltage and rating of the power input is labeled on the back of the switch Ensure the correct mating AC to DC power adapter is used to match voltage and current IP Select This input is used to set the IP address offset and it is set at the factory Console Not used Bel Air Installation
29. hes Height 31 inches Shipping Weight 330 pounds Two B Data outputs Two Payout Data outputs Two Bonanza Bingo R Data outputs Supports Video King B Data Flashboards including our 4000 6000 7000 7500 7600 and Multimedia Flashboard Series One parallel port for connection to any standard printer One RJ11 modem jack for remote service dial up connection One RJ45 Ethernet port for connection to local area network Two RCA line level audio inputs for audio mixing multimedia capabilities Two RCA line level outputs for connection to hall audio system or monitor speakers One 1 4 inch microphone input jack for caller audio equipment Dedicated video graphics card for crystal clear caller and hall video displays One NTSC video output for connection to hall video equipment displaying live ball image and switching to card verification 1mage Fluorescent light ball chamber for maximum clarity and ball action view Bel Air Installation Set up and Configuration Manual 33 October 1 2009 Appendix Exploded assembly Bel Air Installation Set up and Configuration Manual October 1 2009 35 37 DATE E REVISION APP D May 4 2007 A Drawing officially released Dec 10 2007 Knob replaces Vinyl Cap Item No 103 in JJL BOM added Balloon numbers have changed accordingly Notes on Sheet 18 c c m changed Mar 19 2008 C QAD No of Pryramid Display changed from JJL 1736M015F to 1736M600
30. iBiiciriurj Bec PH 6 5 Layout of the devices and controls 11 eeeeeeeeeeeee eee ceeeeee rere n nnn 7 6 Connector IaVOUlS ciii Eee ei ELE KC a 8 mielbit mePEe i mllzdedo o S 8 eee eo T m m UM 9 6 2 Monitor External Cables ccccccccccccccseceeceeceeceeeeceeseeeceeseeceeseeeeeeeseeeeeseeeeeeeas 11 6 3 Monitor Internal Cables ccccccccscccccceseceeceeeeeseeeceeseeeceesseeeeesaeeeeesseeeeeeseeeeeeeas 12 6 4 PC Video In Cable eiecit o ci Seed lees ee eee abr ined tide nai EU eed 13 SPsNZEM scere Cumann a tboessateiaaneaeenaa eet 14 6 6 Wired Video Switch Back 222 s2iccic seccncstaectaeetedsce ebedec tended san a e acon iode Rad 15 6 7 NIOCO SWITCM ETOFPLD S iiri iia c etui od at leds Ue xerox us oda ino bte Se UU inco al eases 16 6 8 Wired Network Switch Back ccccccssceccsseeteeseeteececsneeeceneeeseneeeseseetsnseetsneeensness 17 6 9 1 0 BOX FROM MERERETUR T E T URN 18 6 T0 OX Box External GableSsse ie isisves RU Rebels ised rove Ut is etai Dee aie 20 O21 Wired IO BOX vie dE M aaa 22 O32 Ball ame as cscs aiacacnstonsetucniduanavacedeinva eaaa SLE n A Latis oso LES docu esas D 24 7 ODGFALING TNE BOI lg 25 SS Servicing and ClO AIAG eer 26 9 TROUDIESIIOOUING tenete reet 27 US Luque 28 Ti SONIC c 30 12
31. iers to remove the retainer clip from the lever and then completely remove the lever 57 Bel Air Installation Set up and Configuration Manual Appendix Motor Replacement Step 6 Remove the Ball Door Assembly There are 6 screws to remove 3 on each side You may also want to put something underneath to support the door so it doesn t fall t E 58 Bel Air Installation Set up and Configuration Manual Video King Be sure to carefully guide the door down and out away from the desk Step 7 Remove the Motor Tray Assembly Unplug the motor from the extension cord and lift up and out careful not to scratch or crack the plexiglass ball chamber enclosure Complete steps in reverse order for reassembly Do not forget to re tighten the 3 screws on the Ball Deflector 59 Bel Air Installation Set up and Configuration Manual
32. ll or too large The ball image is washed out Ball switches stop responding Flashboards stop responding Motor runs constantly Unspecified problem Bel Air Installation Set up and Configuration Manual October 1 2009 Solution Check fuse and AC connections DISCONNECT POWER FROM OUTLET BEFORE CHECKING THE FUSE ON THE BACK OF THE IO BOX PANEL Ensure that air filter 1s not clogged Ensure static spring is straight and secure Use the zoom and focus to adjust image Set the white level control to A C Ensure there are no strong lights directly overhead Press reset switch on I O board several times Reset I O board and check cables Ensure that the motor bypass switch is turned off Call help desk 1 888 246 4609 2 10 Warranty 10 Warranty Product Limited Warranty Subject to the terms and conditions herein below Video King as the Manufacturer warrants that the hardware products it manufactures will be free from defects in materials and workmanship for a warranty period of one 1 calendar year from original invoice date THIS EXPRESS AND LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY AND ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE MANUFACTURE S MAXIMUM LIABILITY WILL BE LIMITED EXCLUSIVELY TO REPAIR OR REPLACEMENT AT MANUFACTURER S OPTION OF ANY DEFECTIVE PRODUCT THE WARRANTY HEREIN IS CO
33. ll PA speakers Note If you want the audio to go to the monitor speakers plug the 1 8 inch stereo plug from the monitor cable label 5 Monitor Audio In into the back of the computer label 5 in Figure 1 Computer back page 9 Bel Air Installation Set up and Configuration Manual October 1 2009 Video King 9 IO Box Audio In Plug the 1 8 stereo plug cable from the I O Box cable label 9 IO Box Audio In into the Audio In jack on the back of the computer label 9 in Figure 1 Computer back diagram page 9 10 IO Box Mic In Plug the 1 8 stereo plug cable from the I O Box cable label 10 IO Box Mic In into the Mic In jack on the back of the computer label 10 in Figure 1 Computer back diagram page 9 11 IO Box Modem Plug the RJ11 connector from the back of the I O Box cable label 11 IO Box Modem into the modem port on the back of the computer label 11 in Figure 1 Computer back diagram page 9 12 IO Box LAN 2 Plug in the RJ45 connector from the Network Switch cable label 12 IO Box LAN 2 into the LAN port on the back of the computer label 18 in Figure 1 Computer back6 1 Computer Back diagram page 9 13 IO Box Printer Plug the DB25 P connector cable label 13 IO Box Printer into the printer port on the back of the computer label 9 in Figure 1 Computer back6 1 Computer Back diagram page 9 Bel Air Installation Set up and Configuration Manual 21 October 1 2009 6 Conmectorlayous 000
34. nal amplification All internal sounds are mixed and the result is provided on this output Mic In A microphone input is provided and is mixed with internal audio and fed to Audio Out Video Out Not Used Video outputs feeds are take directly from the Video Switch Parallel Printer A pass through printer connection from the computer is provided for easy connection to an external printer Modem This interface 1s connected to a telephone line and connected to the internal modem card in the computer 18 Bel Air Installation Set up and Configuration Manual October 1 2009 Video King Network This interface is for connection to the Local Area Network It 1s connected to one of the internal Network Switch ports Autocom Not used Bonanza These RJ11 connectors are for interfacing to the Bonanza flash boards Payout These RJ11 connectors are for interfacing to the Payout flash boards B Data These RJ11 connectors are for interfacing to the B Data flash boards Motor This switch allows you to manually turn on the Blower Motor 5V This LED indicates that the IO box internally circuitry has 5V power Reset This switch allows you to manually reset the IO Box Master On Off Switch This switch allows you to turn power on or off to all components within the Desk The computer must be properly shutdown before power is turned off When power is turned on the computer will have to be
35. rior written permission of Video King e The text and graphics are for the purpose of illustration and reference only Specifications on which they are based are subject to change without notice e The software described in this document is furnished under a license The software may be used or copied only in accordance with the terms of that agreement e Information in this document is subject to change without notice Corporate and individual names and data used in examples herein are fictitious unless otherwise noted e The use of masculine gender terms is to be interpreted as being non gender specific and is used solely to minimize textual complexity Copyright O 2007 Video King Bel Air PowerServer PowerEdit PowerPlay PowerTouch Super Champ and Lil Champ are trademarks of Video King All other product names are trademarks or registered trademarks of their respective owners and are hereby acknowledged e9 WARNING AC Cord replacement if the cord is damaged it must be replaced by a cord or assembly from the manufacturer IMPORTANT IO box and PC AC cords must be plugged into its own sock outlet A duplex receptacle is acceptable Bel Air Installation Set up and Configuration Manual October 1 2009 Table of Contents A TPTROGUGCTIONN e 1 2 Unpacking th COnsol6 eiicc iis eaa Coa EES 4 3 Installing th console eren deines e Ewa iaaa 5 smizi eie
36. s XP Operating System Removable front and side panels for easy maintenance Removable motor and base for easy maintenance NTSC camera for live ball image Secure cabinet design with lockable panels Software Controlled Video Switch for enhanced multi media control Software Features Compatible with e BOS gaming systems including Video King s PowerTouch fixed base systems Champion II gaming tablet and full line of handheld bingo devices Compatible with Bingo Racing software Supports PowerVideo software for multimedia flashboard displays Integrated presentation software for in hall advertising Advanced Windows based PowerEdit game program editor Digital image picture in picture for live ball display on the game screen Easy to follow on screen directions and menus Easy back up of game programs Remote access software for program changes troubleshooting Full system restore software Built in verification of all known bingo perms Supports complex pattern definitions including multi level multi card patterns Optional Features Multi year extended warranty A Data signal translator for connection to A Data style flashboards Can be configured for right handed or left handed callers Bel Air Installation Set up and Configuration Manual October 1 2009 Video King Note This manual covers many aspects of the Bel Air M bingo console with the exception of the software It covers unp
37. supplied by Video King refer to product User s Manual for Preventative Maintenance Schedule To request warranty service you must within the warranty period contact Video King at 1 888 246 4609 or contact your local Video King Distributor for assistance Product s should be returned to Video King at the customer s expense upon receipt of a Return Material Authorization Number RMA The customer must ship the products back to Video King in their original or equivalent packaging Customers are responsible for the cost of shipping to Video King and must insure the package s for loss and or damage during shipping Video King shall not be responsible for any loss and or damage during shipping by the customer 28 Bel Air Installation Set up and Configuration Manual October 1 2009 Video King If it is found that non Video King accessories were added to the system and are found to be the cause of the reported problem or if the problem is not related to hardware covered under this warranty a service charge WILL be applied During the period of this warranty Video King at its option will repair or replace products covered Video King reserves the right to send a whole replacement product for the system or a replacement for portions of the system rather than repairing and returning the complete system that was originally returned for repair Video King uses new and reconditioned parts made by various manufacturers in performing warr
38. the Touch Screen input on the back of the computer label 4 on Figure 1 Computer back page 9 5 Monitor Audio In Connect the 1 8 inch stereo plug cable label 5 Monitor Audio In to green input on the back of the computer label 5 on Figure 1 Computer back page 9 Plug the cable into the monitors if you want the audio to go to the monitor speakers Note If you want the audio to go to the hall PA system plug in the 1 8 inch stereo plug from the I O box cable label 8 IO box Audio Out into the back of the computer label 5 in Figure 1 Computer back page 9 Bel Air Installation Set up and Configuration Manual 11 October 1 2009 6 Connector layouts 6 3 Monitor Internal Cables Figure 4 shows the monitor internal cable connections MONITOR VGA CT MONITOR AUDIO IN 5 MONITOR DC 12V 2 Se ae Im E CC CILE S A i LE B i Figure 4 Monitor internal cables Make the following connections internally to the monitor 1 Monitor VGA Plug the DBIS5P VGA connector cable label 1 Monitor VGA to the monitor 2 Monitor DC 12V Plug the DC barrel plug cable label 2 Monitor DC 12V into the Monitor DC barrel jack cable label 3 Monitor Power Jack There are typically two DC barrel plugs and you can plug either one into the monitor The second DC plug is unused 4 Monitor Touch IF Plug the DB9P serial connector cable label 4 Monitor Touch IF into the Monitor DB9S connector cable label 4 PC Touch Screen
39. wing sections show component connectors and connections Figure 3 Series 11 PC back 8 Bel Air Installation Set up and Configuration Manual October 1 2009 Video King 6 1 Computer Back Figure 1 shows the connectors that you plug the devices into Figure 2 shows the back of a correctly wired computer Figure 3 shows the series 11 PC back Figure 1 Computer back Figure 2 Wired computer back Legend 120 VAC PC I O box serial TISCALI TOES PS 2 keyboard PC Audio in blue The numbers refer to the cable labels purple PC Mic in red The letters refer to unlabeled devices PS 2 mouse green PC Modem Line in or cables Hardlock USB If you want the audio to go to the N d VGA PC Printer LPT monitor speakers plug in Monitor ie PC Video in VGT Audio In cable label 5 in Figure 2 PC VGA blue from the monitor to the back of the PC Video out ane PC Touch screen to hall monitors goupulen eoe uou Ege uale serial PC LAN If you want the audio to go to the hall PA system plug in PC Audio Out PA PC Audio Out green POI AE gre ekal 8 foma e WO bor m the badk of the computer label 5 in Figure 1 Cable label 8 is not shown in Figure 2 because cable label 5 is plugged in Bel Air Installation Set up and Configuration Manual 9 October 1 2009 6 Connector layouts The following interfaces require connection on the back of the computer The numbers correspond with the cable labels and th
40. y 6 Bel Air Installation Set up and Configuration Manual October 1 2009 Video King 5 Layout of the devices and controls The following user accessible devices and controls are located on the desk e Ball Camera and Ball Chute located at top of desk e Monitor and Touch Screen located on left or right of desk top e Ball Tray located on top front of desk e Ball Tray Release top control directly below Ball Tray e Ball Chamber Release located directly below Ball Tray Release e Ball Chamber Door top door in middle back of desk e Blower Motor Door bottom door in middle back of desk e Right Door PC Keyboard and mouse access e Left Door Network Switch Video Switch and IO Box access e Front Door Access to wiring must remove Left and Right doors first Bel Air Installation Set up and Configuration Manual 7 October 1 2009 6 Connector layouts 6 Connector layouts This section describes the connection between the major internal components within the desk The major interconnected components are the Computer Monitor Keyboard Mouse I O Box Video Switch Network Switch Ball Camera Master Panel Ball Rail Fluorescent Lamp Blower Motor and Power Block See section 13 Wiring diagram page 32 for a schematic diagram of major component interconnects See the section 12 Cable label matrix page 31 for a list of the cables and their label names and numbers The follo
Download Pdf Manuals
Related Search