Notice
Contents
1. AL models available NTSC 525TV lines 60 fields sec PAL 625 TV lines 50 field sec 768 x 494 NTSC 752 X 582 PAL 520 TVL 0 4 Lux F21 2 IR OFF 0 Lux IR ON Over 48 dB AGC off 1 50 1 60 1 100 000 1 0Vp p 75ohm video test port 0 45 Fixed focal length Vari Focal Lens f 3 6 4 3 6 8 12mm f 2 9 10mm F 1 2 3 6mm standard Yes ON Yes ON Yes 2500 K 9000 kK Internal sync Auto IR Cut Removable Visible light sensor Electronic Yes 40 emitters in two arrays 20 000 hours nominal 50 feet 850nm IP67 Ye 12VDC 4 8W max at 12VDC Heater ON amp IR LED ON 40 C 60 40 F 140 F 105 x 140 x 65mm 600g Side Rear Wall Ceiling mounting options no bracket required Can be rotated 360 on axis in 90 increments to fit mounting position Dual Position Single Position oe IR LEDs Direction end side end CE FCC 5 CONFIGURATION A To open the housing remove the cover 1 Using the tool provided remove 4 screws to separate camera s base from its cover 2 Detach the light sensor wire and LED wires from connectors on the camera PCB board 3 Detach LED illuminator wire from wire retaining clip on camera body B Making Z axis adjustment 1 Remove the two screws closest to the front of the camera bracket and loosen the two screws at the side of the camera bracket Remove these screws emove the Loosen these screws 2 Make Z axis adj2. IJ EverFocus Mobile IR Wedge Cameras Operation Instructions EMW330 Dual Viewing Position EMW330T Varifocal Al Lens Please read this manual first for correct installation and operation This manual should be retained for future reference The information in this manual was current when published The manufacturer reserves the right to revise and improve its products All specifications are therefore subject to change without notice PRECAUTIONS 1 Do not install the camera near electric or magnetic fields Install the camera away from TV radio transmitters magnets electric motors transformers and audio speakers since the electromagnetic fields generated from these devices may distort the video image Never disassemble the camera beyond the recommendations in this manual nor introduce materials other than those recommended herein Improper disassembly or introduction of corrosive materials may result in equipment failure or other damage Try and avoid facing the camera toward the sun In some circumstances direct sunlight may cause permanent damage to the sensor and or internal circuits Keep the power cord away from water and other liquids and never touch the power cord with wet hands Touching a wet power cord with the hands or touching the power cord with wet hands may result in electric shock Cleaning Use a damp soft cloth to remove any dirt from the camera body being careful not to scratch the covers over the lens and IR emi
3. als and components which can hochwertigen Ihr EverFocus Produkt wurde entwickelt mit qualitativ Materialien und Komponenten die recycelt und wieder sales everfocus com EverFocus Europe UK Unit 12 Spitfire Business Park Hawker Road Croydon Surrey 4WD UK TEL 44 0 20 8649 9757 0845 430 9999 FAX 44 0 20 8649 9907 www everfocus com salesuk everfocus com be recycled and reused This symbol means that electrical and electronic equipment at their end of life should be disposed of separately from your household waste Please dispose of this equipment at community waste your local collection recycling centre In the European Union there are separate collection systems for used electrical and electronic product verwendet werden k nnen Dieses Symbol bedeutet dass elektrische und elektronische Ger te am Ende ihrer Nutzungsdauer vom Hausm ll getrennt entsorgt werden sollen Bitte entsorgen Sie dieses Ger t bei Ihrer rtlichen kommunalen Sammelstelle oder im Recycling Centre Helfen Sie uns bitte die Umwelt zu Please help us to conserve the environment we live in erhalten in der wir leben EverFocus zd
4. efore mounting the Camera please remove the cover as described above and attach the video test cable to the PCB board note that the ground pin is the upper pin B Place the mounting template and drill 4 pilot holes 3 7mm diameter if plastic anchors are not used for the mounting screws using a drill and a clearance hole for the video power cable connectors typically 9 16 or more 10 C Apply sealant generously around all holes Place the camera and rubber gasket to align the mounting holes with the pilot holes or anchors Insert the mounting screws using the rubber washers and tighten fully using the appropriate screwdriver or drive tool rubber gasket D Adjust the angle and while viewing the image using a test monitor such as the EN200 WC Lock the two screws closest the front of the camera bracket and tighten the two screws at the side of the camera bracket RE Lock these screws E Attach desiccant pack as described in 5F Do not open the desiccant pack until the housin is ready to be permanently sealed F Attach the top cover light sensor wire and LED wires to their connectors G Close the housing as described in 5F above EverFocus Electronics Corp EverFocus Taiwan 12F No 79 Sec 1 Shin Tai Wu Road Hsi Chih Taipei Taiwan TEL 886 2 2698 2334 FAX 886 2 2698 2380 www everfocus com tw marketing everfocus com tw EverFocus China Beij
5. ing Room 609 Technology Trade Building Shangdi Information Industry Base Haidian District Beijing 100085 China TEL 86 10 6297 3336 39 FAX 86 10 6297 1423 www everfocus com cn marketing everfocus com cn EverFocus USA California 1801 Highland Avenue Unit A Duarte CA 91010 USA TEL 1 626 844 8888 FAX 1 626 844 8838 www everfocus com EverFocus Europe Germany Albert Einstein Strasse 1 D 46446 Emmerich Germany TEL 49 2822 93940 FAX 49 2822 939495 www everfocus de info everfocus de EverFocus China Shenzhen 4F No 2 D4 Building Wan Yelong Industrial Park Tangtou Road Shiyan Baoan Shenzhen Guangdong 518101 China TEL 86 755 2765 1313 FAX 86 755 2765 0337 www everfocus com cn marketing everfocus com cn EverFocus USA New York 415 Oser Avenue Unit S Hauppauge NY 11788 USA TEL 1 631 436 5070 FAX 1 631 436 5027 www everfocus com ND sales EverFocus Japan SE Kinshicho City Koto Bashi Sumida Ku Japan TEL 81 3 5625 8188 FAX 81 3 5625 8189 www everfocus co jp 2 13 4 130 0022 Building Tokyo info everfocus co jp EverFocus India Suite 803 Housefin Bhavan C 21 Bandra Kurla Complex Bandra East Mumbai 400051 India TEL 91 22 6128 8700 FAX 91 22 6128 8705 www everfocus in sales everfocus in Your EverFocus product is designed and manufactured with high quality und hergestellt materi
6. the IR LEDs are at factory end position To change them to the side position 1 Remove the 4 screws as shown in figure to detach the IR LED panels and light sensor upper bracket from d the camera cover 2 the factory light sensor end bracket by the light sensor side bracket Hemove the 2 screws from the light sensor end bracket 3 Reattach the light sensor to side bracket with the same screws removed in step 2 4 Cross the IR LED panels to the opposite sides of the cover and rotate them to point out the side Place the light senor bracket as shown Use the 4 screws remove in step 1 above to attach the IR LED panels and light sensor side bracket to the camera cover E Attach desiccant pack DO THIS LAST JUST BEFORE CLOSING THE HOUSING WHEN THE INSTALLATION IS COMPLETE The desiccant pack has glue on it use the glue to attach it on the left side of the upper cover Reattach cover and seal housing 1 Reversing the steps in A above a Reattach the safety cord to the base position the metal ferrule to the side so it does not overlap the gasket and interfere with the cover when it is replaced b Reattach the LED illuminator wires and place into clips c Reattach the light sensor wire 2 Replace the cover onto the base making sure the gasket lies flat between the base and cover 3 Attach the cover with the four screws removed during step A 1 6 MOUNTING A B
7. tion when needed 2 COMMON FEATURES 1 3 Sony Super HAD CCD Resolution 520 TVL Vandal resistant IP67 housing Dual IR illuminators for 50 foot range Side Rear Wall Ceiling mounting options Built in heater Video Test Connector eo 0000909 UNIQUE FEATURES e EMW33OT vari focal lens model with ICR e EMW330 fixed lens model with dual position lens 3 CONTENT LIST 1 Camera unit 2 User s manual 3 Accessory kit containing l Front light sensor bracket EMW330 only li 4 screws and plastic anchors lil 4 sheet metal screws and rubber washers IV Tool for tamper resistant cover screws Mounting template Desiccant pack with gummed tape to attach pack inside camera Rubber gasket for base of camera Power adapter pigtail Video Test Cable Pickup Device Video Format Scanning System Picture Elements ensitivity N Ratio Video Outputs amma Correction Lens Back Light Comp Auto Gain control Auto White Balance ync Mode Day Night Day Night Detection Built in Heater IR LEDS Weather Proof Power source Power consumption Dimensions WxDxH Weight Mounting Options Camera Angle Viewing Direction 9 SiZ DDD QO S M C Hz A D o o Y a a m U 5 JJ 5 18 2 ITI 2 20 JJ 7 S o o O Tl O e 7 Si S E 2 o EMW300 EMW33OT 1 3 SONY Super HAD CCD NTSC and P
8. tters Use lens tissue or a cotton tipped applicator and ethanol if it becomes necessary to clean the camera lens Please do not use complex solvents corrosive or abrasive agents for cleaning Do not operate the camera beyond the specified temperature humidity or power source ratings Use the camera at temperatures within 40 C 60 C 40F 140F The input power source is 12VDC TABLE OF CONTENIS UT T 2 COMMON cuiii 2 Ip HP 2 o 3 cp g m O 4 sued 10 1 PRODUCT OVERVIEW With a streamlined vandal resistant IP67 weatherproof wedge type chassis the EMW330 is ideal for transit school bus and similar applications Choose the EMW330 fixed lens model with dual position lens and IR illuminator modules enabling the user to field select a side rear wall or ceiling mounting configuration for best viewing angle and mount the camera easily without brackets The IR illuminators provide clear images up to 50 feet away Or for flexibility in field of view choose the EMW330T with choice of 2 9 10mm auto iris varifocal lens true day night operation and ability to rotate the viewing angle for side wall or ceiling mounting Both cameras have built in visible light sensors to monitor ambient light and provide IR illumina
9. ustment To avoid distortion do NOT point the camera at the corner LB of the lens cover If the Z axis is rotated past 45 side view EMW330 only see step D below to reposition the IR illuminators and light sensor bracket Tighten the side screws 3 Install the second pair of screws if the holes align C Rotating the camera module on axis 1 Remove the 4 screws from the side of the camera bracket Remove the module bracket from the camera bracket 2 Depending on the mounting orientation either a Invert the assembly 180 and reattach the module bracket to the camera bracket Or b Remove two screws from the front of the module bracket rotate the module right or left 90 so that the lens is positioned to the correct direction and reassemble the module to the module bracket then reattach the module bracket to the camera bracket 1 Remove 2 screws from Note two red arrows right side of camera bracket indicating proper orientation of camera module When unit is installed these arrows should be pointing UP 2b Remove the module bracket from the module Adjust the module right or left 90 and reassemble 2a Rotate the module and module bracket 180 and reattach 1 Remove 2 screws from left side of camera bracket D EMW330 ONLY Change the viewing direction If the Z axis adjustment above points the lens toward the side of the housing the IR LEDs and light sensor must be repositioned Here
Download Pdf Manuals
Related Search
Notice notice notice to vacate notice of settlement noticed synonym noticeably notice 123 notice to employee notice of privacy practices notice to consumer notice to quit notice of completion notice to employee 2025 notice and acknowledgment of receipt notice of hearing notice of entry of judgment notice of transfer and release of liability noticeable synonym notice of intent notice format notice of change of address notice of remote appearance form ra-010 notice period notice of release of liability notice board notice of appearance