Notice evolution- FINAL.indd - Height Safety Products and Projects
Contents
1. New Zealand Requirements e Inspection by the user of the system and attachments before and after use e Inspection and documentation by a competent person of the self retrac ting lifeline every three 3 months e Inspection and documentation by a competent person of the harness and lanyard every six 6 months e Inspection and documentation by an accredited installer of the system every twelve 12 months e Inspection and documentation by an authorized service agent of the self retracting lifeline every twelve 12 months 6 CONNECTORS 6 1 When connecting the carabiner check that the locking system is in the proper place 6 2 CAUTION The carabiner is essential for your safety Therefore we advise you to 6 2 1 Assign personally the connector whenever possible 6 2 2 Check it before each use in particular for absence of deformation absence of wear marks correct operation of locking system 6 2 3 Similarly if the carabiner has been used to arrest a fall for safety reasons it is essential to remove it from service or return it for verification 7 I RECOMMENDATIONS SPECIFIC TO CABLE ANCHORAGE DEVICES Warranty Capital Safety Group is ISO 9001 certified 2000 The manufacturing of the lifeline is carried out under continuous quality control Capital Safety Group guarantees all the components of the lifeline from any manufac turing defects The equipment is guaranteed for a year this guarantee applies to the replacemen2. a maximum of 1 8m 6 feet ANSI Z359 1 1992 or five feet per ANSI A10 14 1991 for fall arrest systems and zero feet for restraint sys tems 1 11 In the course of use take all necessary steps to protect the system or component from hazards related to the operation burns cuts sharp edges abrasion chemical attack tangling or twisting of the cable webbing or rope electrical conductivity weather conditions pendulum effect due to fall etc A SHARP EDGES Avoid working where the connecting subsystem i e full body harness lanyard self retracting lifeline etc or other system components will be in contact with or abrade against unprotected sharp edges If working with this equipment near sharp edges is unavoidable protection against cutting must be provided by using a heavy pad or other means over the exposed sharp edge B SWING FALLS Swing falls occur when the anchorage point is not directly above the point where a fall occurs The force of striking an object while swinging horizontal speed of the user due to the pendulum effect can be great and may cause serious injury Also in a swing fall situation the total vertical fall distance of the user may be greater than if the user had fallen vertically directly below the anchorage point Thus there will be an increase in the total free fall distance and the distance needed to arrest the fall will increase Swing falls can be minimized by working as close to directly below the an
3. chorage point as possible If a swing fall situation exists in your application contact Capital Safety Group before proceeding C RESCUE It is vital that a rescue plan can be implemented should a user fall at any point along the System It should be assumed that the fallen user will not be able to participate in their rescue Different rescue solutions apply for different types of applications Capital Safety Group can recommend a suitable rescue system for each application and can supply appropriate equipment For this purpose any person working at a height must never remain alone at the place of work and after a fall D AFTER A FALL If the System has been used to arrest a fall fur ther use of the system should be restricted until a Capital Safety Group Technician or factory authorized representative has performed a full site inspection During the arrest of a certain components of the system will deform to help dissipate some of the fall s energy and will require repla cement If practical any inspection should be performed using suitable access equipment which does not require the Technician to tie off to the Sys tem The user s full body harness and shock absorbing lanyard should be discarded If a self retracting lifeline was used it must be returned to Capital Safety Group or a factory authorized facility for inspection and maintenance 1 12 This equipment is designed to be used with the components or sub systems of th
4. dian requirements gt 22kN 5000lbs CSA Z259 12 98 CAN CSA Z259 1 95 R1999 CAN CSA Z259 2 1 98 R2004 CAN CSA Z259 2 2 98 R2004 CAN CSA Z259 10 M90 R2003 CAN CSA Z259 11 M90 R2003 Australian requirements 15kN for 1 person gt 21KN for 2 persons AS NZS1891 4 PART 4 AS NZS1891 4 PART 4 AS NZS1891 2 PART 2 AS NZS1891 4 PART 4 AS NZS1891 1 European harnesses These points are identified by a capital A when they are independent or by 1 2 A or 1 2A when 2 points have to be connected together 1 IMPORTANT RECOMMENDATIONS FOR PPE SYSTEM 1 1 This safety equipment must only be used only by competent persons who have been given appropriate training repeat as often as necessary or who are working under the immediate responsibility of a proficient supervisor The user must be trained in the use and be aware of the characteristics the application limits and consequences of the incorrect use of the equipment Before each use the user must examine the equipment visually to ensure it is in perfect operating condition It is important to check for deforma tion corrosion sharp edges and abrasive areas on the metal parts of the system or component Similarly check for cuts burns broken wires extensive wear and change of color or rigidity in the textile parts of the system or component 1 2 Asystem or a component that has sustained a fall or on which visual inspection leave
5. e Capital Safety Group harnesses lanyards with energy absorbers retractable type fall arresters No modifications are to be made to the system or components without the written consent of the manufacturer The replacement or substitution using components or subsystems that are not approved could compromise compatibility between equipment and could affect the integrity and safety of the system as well as war ranty All repairs are to be made according to the procedures detailed by the manufacturer 1 13 Dealers or retailers of this fall arrest equipment will ensure that a user manual is supplied in the language of the country of sale 1 14 Refer to national consensus standards applicable local state and federal OSHA requirements governing this equipment for more informa tion on personal fall arrest or restraint systems and associated system components 2 CONNECTION TO A FALL ARREST HARNESS 2 1 The connection of a fall arrest system to a harness MUST EXCLUSI VELY be carried out using the upper dorsal sternal or pectoral attaching points these points may also be used for connecting a descender or an elevation rescue system 2 2 The lower side positioning anchorage points of a belt or a harness with a belt must be used SOLELY for connecting to a work positioning system and NEVER to a fall arrest system 2 3 The anchorage point of a sit belt or a harness with a sit belt is to be used EXCLUSIVELY for connection to a w
6. evolution JET horizontal lifeline aech i USE AND MAINTENANCE MANUAL NOTICE D UTILISATION ET D ENTRETIEN GEBRAUCHS UND WARTUNGSANWEISUNG MANUAL DE UTILIZACION Y DE MANTENIMIENTO MANUALE D USO E MANUTENZIONE BRUKSANVISNING OCH SKOTSELRAD GEBRUIKSAANWIJZING EN ONDERHOUDSINSTRUCTIES NAVOD K UDRZBE A POUZITI horizontal lifeline olution Jem English USE AND MAINTENANCE MANUAL You have just purchased a Capital Safety anchor device and we would like to thank you for your trust For this equipment to provide you with the safety and comfort you are entitled to receive we must ask you to keep and follow TO THE LETTER the following instructions All users should be Descender device Elevation rescue system Marking of anchorage keys for EN1496 EN361 ANSI Z359 1 and OSHA requirements ANSI Z359 1 and OSHA requirements ANSI Z359 1 and OSHA requirements CAN CSA Z259 2 3 99 CAN CSA Z259 2 3 99 CAN CSA Z259 10 M90 AS NZS1891 1 PART 1 required to refer to this manual Correspondence of standards and requirements to which this manual refers Anchorages Connectors Fall arrest system Work posi tioning and restraint system European standards EN 795 strength gt 1000 daN North American standards ANSI Z359 1 and OSHA requirements ANSI Z359 1 and OSHA requirements ANSI Z359 1 and OSHA requirements ANSI 2359 1 and OSHA requirements Cana
7. menti Kommentarer Opmerkingen Pozn mky DESCRIPTIVE SHEET FICHE D ESCRIPTIVE BEGLEITBLATT FICHA DESCRIPTIVA SCHEDA DESCRITTIVA SPECIFIKATIONSKORT PRODUCTGEGEVENS POPISNY DOKUMENT Product Produit Produkt Producto Prodotto Produkt Product V robek Model amp Type identification Mod le amp type Modell amp Typ Identifizierung Modelo y tipo Modello amp Tipo Modell och typ Model amp Type Identifikace Model amp Typ Manufacturer Fabricant Hersteller Fabricante Produttore Fabrikant Vyrobce Capital Safety group Month Year of manufacture mois Ann e de fabricant Herstellungsmonat und jahr Mes Ano de fabricacion Mese Anno di produzione Tillverkningsmanad ar Maand jaar fabricage M sic Rok vyroby Purchase date Date d achat Kaufdatum Fecha de compra Data di acquisto Kopdatum Maand aankoop Datum koup Identification number R f rence Kennnummer Referencia Riferimento Beteckningsnummer Productnummer Identifika n slo Life expiry date MM YY Lebensdauer bis MM JJ Fecha de caducidad MM AA Data di scadenza MM AA Utg ngsdatum MM AA Uiterste gebruiksdatum MM JJ Datum vypr en u itn Zivotnosti MM RR Date first put into use Date de premi re utilisation Datum der ersten Inbetriebnahme Fecha de primera utilizaci n Data del primo utilizzo Datum for f rsta anvandningstillfalle Datum eerste gebruik Datum prvn ho opera n ho nasa
8. ork positioning system a des cender or an elevation rescue device and NEVER to a fall arrest system 2 4 The use of a work positioning system alone is allowed only in a res traint mode In case of any risk of fall the system must be completed by a fall arrest protection device A LO Australian conformity For use in Australia and New Zealand the user is only permitted to attach to the rear dorsal D ring or rear dorsal extension of a full body harness for a fall arrest system For a restraint system the user is only permitted to attach to the rear dorsal D ring rear dorsal extension or a frontal sternum D ring Waist belts are NOT PERMITTED for fall arrest or restraint systems 3 USES CORROSION Do not leave user equipment of the System i e full body harness shock absorbing lanyard or Shuttle for long periods in environ ments where corrosion of metal parts could take place as a result of va pors rising into the atmosphere from organic materials Caution should be exercised when working around sewage or fertilizer because of their high concentration of ammonia which is very corrosive Use near sea water or other corrosive environments may require more frequent inspections or servicing to assure corrosion damage is not affecting the performance of the product CHEMICAL HAZARDS Solutions containing acids alkali or other caus tic chemicals especially at elevated temperatures may cause damage to this equipment When working with
9. ospheres Australian conformity For all products used in Australia New Zealand refer to User Instruction Manual Practices and Procedures part number A006 for additional infor mation regarding care and maintenance of equipment 5 INSPECTION FREQUENCY 5 1 Periodic examination is essential for the safety of the user This exa mination guarantees the efficiency and trouble free operation of the sys tem or component Be sure to fill in and preserve carefully the descriptive sheet making a note of any periodic checks Refer to the document entitled List of points to be checked in order to perform periodic review 5 2 Life duration The frequency of the periodic examinations must allow for factors such as legislation type of equipment frequency of use and environmental conditions In any case the system or component must be examined at least once each year by a competent person cleared by the company manager or appointed by the current legislation of the country to decide on possible return to or removal from service or scrapping 5 3 Any competent person qualified by the company manager having doubts about returning a system or component to service excessively complex system concealed mechanism etc must contact the manufac turer who will direct him towards persons approved for the task 5 4 During these examinations it is important to check that the markings are legible on the system or component Australian and
10. s any doubt must be removed immediately from service Only competent and skilled persons may decide on the possibility of re turn to service given in writing 1 3 The user must be in good health in order to use the equipment WARNING Consult your doctor if there is any reason to doubt your fi tness to safely absorb the shock from a fall arrest Age and fitness se riously affect a worker s ability to withstand falls Pregnant women or minors must not use the system 1 4 This product must not be used other than for the purpose recom mended by the manufacturer and must not be diverted from its initial and designed purpose scvolution Em horizontal lifeline III 1 5 When a fall arrest system is being used for safety it is essential to check the clearance under the user s working zone to prevent a collision with an obstacle or the ground in case of fall 1 6 Ensure that a proper rescue plan and the ability to execute it are available for each specific application of the equipment before using it 1 7 Use this product at an ambient temperature included between 40 C and 60 C 1 8 Before each use ensure that the recommendations for use of each of the components is complied with as stated in the user manual It is strongly recommended that components used on the system come from the same manufacturer to ensure product reliability and performance consistency WARNING Do not alter or intentionally misuse this eq
11. such chemicals frequent inspection of this equipment must be performed Consult Capital Safety Group if doubt exists concerning using this equip ment around chemical hazards ELECTRICAL HAZARDS Due to the possibility of electric current flowing through this equipment or connecting components carabiners use extreme caution when working near high voltage power lines 4 MAINTENANCE AND STORAGE The maintenance and storage of your PPE or components are essential operations to protect them and therefore the safety of the user Be sure to comply with the following recommendations 4 1 Use a dry cloth to clean the plastic and metal parts Clean textile component with mild soap and water Never use acid or alkali solvents caustic soda 4 2 Allow components to dry in a ventilated place away from any direct flame or any other source of heat This provision also applies to textile component that have absorbed moisture during use on jE horizontal lifeline I IIIIIIIII English EICH horizontal lifeline 111111111111 4 3 Store the system or component in a room and under conditions com plying with its integrity away from damp and ultraviolet light in an atmos phere that is not corrosive overheated or refrigerated protected from any possible cuts or vibration 4 4 Transport the component or system in a package to protect it from any cuts moisture or ultraviolet light Avoid corrosive overheated or re frigerated atm
12. t of parts considered to be defective On written notification Capital Safety Group agrees to replace the defec tive parts Capital Safety Group reserves the right to analyze the parts on its premises before repair or replacement Limitations to the guarantee The guarantee does not apply to e Lifeline support equipment e Parts that are damaged due to a qualification test or the use of the line other than in the prescribed manner e Assembly of the lifeline Use of the lifeline beyond these capacities Inspection V rification berpr fung Inspecci n Ispezione Besiktning Inspectie Inspekce Competent person Reason for entry Defects noted repairs carried out Next due date Personne comp tente Raison du retour D fault constat ou r paration effectu e Prochaine r vision Zust ndig Grund f r die Einreichung Festgestellte Mangel durchgef hrte Reparaturen Nachste Uberprufung Persona competente Motivo de la devoluci n Defecto constatado o reparaci n efectuada Pr xima revisi n Persona competente Motivo del reso Difetto rilevato o riparazione effettuata Prossima revisione Behorig person Returanledning Faststallda fel eller utford reparation Datum for nasta besiktning Competente persoon Reden terugsturen Opgemerkte Defecten uitgevoerde reparatie Volgende inspectie Zodpov dny revizor Duvody pro zapis Nalezen zavady proveden opravy Datum p t revize Comments Commentaires Kommentar Comentarios Com
13. uipment your sa fety may depend on it Consult Capital Safety Group when using this equipment in combination with other components or subsystems other than those described in this manual Some subsystem and component combinations may interfere with the proper operation of this equipment Use caution when using this equipment around moving machinery and electrical hazards Use caution when using this equipment around sharp edges and chemical hazards 1 9 Whenever possible it is highly advisable to assign the system or component personally to the user 1 10 This system or component must necessarily be attached to an an chorage point Whenever possible to attach a fall arrest system choose an anchorage point located ABOVE the position of the user avoiding any point whose strength may be subject to doubt It is preferable to use the structural anchors provided for this purpose or anchorage points confor ming to the current standards when the strength exceeds the strength levels provided for in the corresponding standards The user will ensure to limit the chances of potential fall from height prefer the use of a res traint system Australian conformity These Systems must be rigged in such a way as to limit the free fall to a maximum of 2m AS NZS 1891 2 for fall arrest systems and zero meter no fall for restraint systems North American conformity These Lifeline Systems must be rigged in such a way as to limit the free fall to
14. ww salagroup com csgne csgne co uk USA CAPITAL SAFETY USA PROTECTA DBI SALA 3965 Pepin Avenue Red Wing MN 55066 1837 USA Toll Free 800 328 6146 Phone 1 651 388 8282 Fax 1 651 388 5065 www salagroup com solutions dbisala com CANADA CAPITAL SAFETY GROUP CANADA LTD 260 Export Boulevard Mississauga Ontario L5S 1Y9 CANADA Toll Free 800 387 7484 Phone 1 905 795 9333 Fax 1 905 795 8777 www salagroup com sales ca capitalsafety com AUSTRALIA CAPITAL SAFETY GROUP LTD 20 Fariola Street Silverwater Sydney NSW 2128 AUSTRALIA Phone 61 2 9748 0335 Toll Free 1800 245 002 Fax 61 2 9748 0336 sales capitalsafety com au ASIA CAPITAL SAFETY GROUP LTD Room 2009 Tower 2 Metroplaza 223 Hing Fong Road Kwai Chung N T Hong Kong CHINA Phone 852 2858 7237 Fax 852 2311 4601 inquiry capitalsafety com hk AL A brand of Capital Safety
15. zen EXAMINATION OF THIS TYPE carried out by the notified organization TYPPRUFUNG durch die zugelassene Stelle EXAMEN DE ESTE TIPO realizado por una organizaci n notificada ESAMINAZIONE DI QUESTO TIPO eseguita dall organismo riconosciuto UNDERSOKNING AV DENNA TYP utf rd av notifierad organisation ONDERZOEK VAN DIT TYPE uitgevoerd door de betreffende organisatie PREZKOUSEN TOHOTO TYPU bylo provedeno uvedenou organizac PRODUCTION QUALITY FOLLOW UP by a notified organization QUALITATSUBERWACHUNG durch eine zugelassene Stelle SEGUIMIENTO DE LA CALIDAD DE PRODUCCI N por una organizaci n notificada CONTROLLO QUALITA DI PRODUZIONE eseguito da un organismo riconosciuto UPPF LJNING AV PRODUKTENS KVALITET utf rd av notifierad organisation CONTROLE PRODUCTIEKWALITEIT door erkende organisatie KONTROLA KVALITY VYROBY je sledov na touto uvedenou organizac No 0082 APAVE SUD EUROPE BP 193 13322 MARSEILLE CEDEX 16 France No 0086 BSI 389 Chiswick High Road LONDON W4 4AL UK 000000896IN A EUROPE MIDDLE EAST AFRICA CAPITAL SAFETY GROUP EMEA Le Broc Center Z l 1 avenue BP 15 06510 Carros Le Broc Cedex FRANCE Tel 33 0 4 97 10 00 10 Fax 33 0 4 93 08 79 70 www salagroup com information capitalsafety com NORTHERN EUROPE CAPITAL SAFETY GROUP NE LTD 7 Christleton Court Stuart Road Manor Park Runcorn Cheshire WA7 1ST UK Tel 44 O 1928 57 13 24 Fax 44 0 1928 57 13 25 w
Download Pdf Manuals
Related Search