User`s manual - Pdfstream.manualsonline.com
Contents
1. For powder whitener please dissolve it before use The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time One time washing quantity shall be lower than the rated capacity The thickness size type of the cloth will influence the actual washing capacity It is suitable for one time washing to put in reasonable amount of laundries and the laundries can be turned round in washing Do not select High water level for laundries small than 1 0kg so as to avoid splashing of water Direct dissolved in the machine 1 Fill water to Low water level 2 Add the power Run for 30 seconds to dissolve it completely 3 Put in the laundries Select suitable water level The instant dissolving of the washing powder 1 Prepare warm water of 30 C and a container 2 Add the powder while stirring to fully dissolve it The powder is more prone to pollute the laundries than the detergent Therefore please use it with proper quantity It is suggested not to use high sudsing detergent Different washing powders have different dosage Please refer to the usage manual of the washing powder for the details 4 Use the operation knobsand buttons a Description of the function of the knobs and buttons Mode and meaning of the indicators O Flashing indicate the running program On indicate the progr2. Full automatic washing machine User s manual This manual is for XQB50 68 Special number 0030506438 e Please read this manual carefully before using Retain it for future reference Contents eNames of the parts ee eee eee eee eee eee Pt Safety precautions ss sivsviesrsesvess vena sos 2 installation and adjustment s s s gt 4 lnstallation the water inlet hose s 6 Preparation before washing tttttrtt 8 Put in the laundries lt lt tttt etter tte 9 Put in the detergent ee ee ee eae ee ee ee ee eee 9 Use the operation kKnobs ssreseree 10 Close the top To i 13 Finish washing SRR ECR CCRC RC RCE RCE NC SCR CECH RCC ORC RT RC ACEC 13 e Disposal after washing Peer eer ere ener a E ere a 14 15 g Trouble shooting rca carout dat Gare an car eat Ga oot ca dat qat Jat carder ont dar dare ony carom Answers to question Packing list Specification eseeee eee eee Names of the parts Top lid Water level knob Detergent bo Lint filter Installed by user Control panel sea Filter cover Inner tub Front control board Drain hose Control panel shee Drain hose hanging hole Pulsator Cabinet Drain outlet Front fixed foot protecting cover Drain hose bushing Back cover Adjustable foot Adjustable foot seam Rear fixed foot Meaning and description of the symbols Contents mark
3. ace of the faucet shall be flat and smooth If not please file it to avoid leakage Connection between the water inlet hose jointer and the water faucet 1 Press the lower end of the lock lever and push down the slider Take off the water inlet hose jointer from the water inlet hose component See to Figure 1 2 Loosen the screw till the water faucet can be accessed Put the jointer of the water inlet hose on the faucet See to Figure 2 If the faucet is too large and the jointer can not be set on the water faucet please loosen the four screws and take out the bushing in the jointer The front end of the faucet must be smooth otherwise it may leak water See to Figure 3 Water inlet hose jointe Slider Screwdriver Bushing Water inlet hose Figure 1 Figure 2 3 Fasten the four screws evenly See to Figure 4 4 Take off the nameplate Twist the fastening nut as per the indication of the figure to seal up the outlet end surface of the faucet See to Figure 5 Remarks Before installation the threading is 4mm above the upper surface of the nut After installation the threading is 2mm above the upper surface of the nut See to Figure 6 About 4mm before twisting about below 2mm after twisting Figure 3 Connection between the water inlet hose and the washing machine 1 Do not take off the water absorption cushion Please check if the cushion is dropped or Nut of the water damaged before each usage If it happens nl
4. am about to run or indicate the selected mode OS Flashing rapidly indicate abnormal condition electio a Oo go o 8 ade Spin Quick Twice Wash Rinse ash wash L Process selection button One or more out of the five process programs are available for your option quick wash twice wash wash rinse spin Start Pause button After the power is switched on push it to start the machine During working push it to pause working During pause push it to resume working 10 b Steps of using the operation buttons and description of the steps Power botton Push the Power button to switch on or off the power When the power is on push it Recto o o S Oo eo O akea again to switch off the power sei ioe Wash Rinse Spin Water Level ow Power iw J High O Reset Water Level button Select or adjust the water level 1 Push the Power button to switch on the power ON OFF 2 Push the Process Selection button to select Process the suitable process After switching on the power the machine will set to standard program automatically including wash rinse spin To select other program push the Process Selection button to select one or more programs among Quick wash Twice wash Wash Rinse Spin Refer to the Selection method of the procedure programs for the selection Page 12 Even there s no wat
5. ashing machine is in stalled on ground with carpet do not block the ventilation hole with carpet The ventilation holes at the bottom 9 Do not wash water proof laundries like the raincoat bike covers etc to avoid abnormal vibrations in spinning X S Do not let the machine share one receptacle with other electric appliances If the power plug is damaged or the plugging into the receptacle is loose do not use the plug any more Fo Safety precautions Do not stretch hands into the working machine It is dangerous even if the rotation is slow Take special care of the children Do not decompose repair or alter the machine by yourself Do not put any hot or heavy items such as the kettle with hot water on the washing machine Do not wash laundries with volatile materials such as thinner petrol etc The handicapped or children without care shall not use the machine To prevent the lint inside the tub from blockingthe cascade outlet during washing please keep the lint filter in good condition and install it to proper position If the lint filter is lost or da maged please contact the local after sales service department of our company Keep the machine away from direct sunlight and heat source like the heater To protect your laundries and wash ing machine please take out all of the coins buttons sand hairpin and other foreign materials before
6. ded before it starts spinning e There may be some water flowing out of the drain hose in the first use of the machine e It is the water remained in the factory inspection of performance e In the final spinning it stops and displays Rinse and starts water inlet e lt is because that the laundries are slanting to one side and the safety switch acts Afte water inlet and stirring the slanting will be removed and the spinning will work 15 Paching list Name Quantity e User s manual One piece Certificate of warranty One piece Components of the water inlet hose The end connecting to the washing machine Jointer connecting the water inlet hose and the water faucet ey The end connecting to the water inlet hose jointer One piece Bottom plate F One piece Tapping screws cu Z q g Egiht pieces Lint filter i One piece Full automatic washing machine One set Specification Water level Water quantity about High 52L Medium 43L Low 30L Injection pressure MPa 0 03 0 78 Rated washing spinning capacity kg 5 0 weight of standard dry cloth 16
7. ed with that symbol are related Warning sign to the safety of the product and the personal safety of the users Please operate in strict conformity to the contents otherwise it may cause damageof the machine or injure the personal safety of the user Forbidding sign Contents marked with that symbol are actions forbidden to perform Performing of those actions may result in damage of the machine or injure the personal safety of the user Please check if the power receptacle has good earthing condition before using to guarantee your safety Safety precautions Please insert the power cord into special receptacle with rated vol tage Be sure to use single phase three pins receptacle The earthing terminal of the receptacle must be earthed reliably If possible please adopt electric leakage protector When the machine is normally using please put the power plug at the location easily to be insert ed and extracted by hand Be sure to pull the plug off when there s power failure or the machine is being moved cleaned orwhen it is idle If the power cord is bad to avoid risk it is required to replace it by the technicians ofour special shop or the after sale service department Keep the pin of the power plug clean Do not put the machine at damp place like the bathroom Never wash it with water Do not place wet laundries on the control panel Do not use water hotter than 50 C In case the w
8. er in the tub the spinning will start after a certain period Do not use the Twice wash program for the woolen laundries e Wash the laundries that are prone to lt gt lose colors separately from other laundries The pulsator will not rotate unless the water is filled to selected water level Times of pushing the Process Selection button Selected procedure program Applicable procedure Contents the lighted indicators indicate the programs about to run Wash rinse spin standard program When the common laundries need washing rinsing and spinning ick Sree Twice wash Wash rinse O 6 spin O Wash the washing liquid remains in the tub Repeat using the washing liquid Quick wash Twice wash Wash rinse O spin Wash rinse the rinsing liquid remains in the tub Repeat using the washing liquid Quick wash Twice wash Wash rinse O O spin Rinse spin When the laundries need rinsing and spinning after manual washing Twice v Wash rinse O spin O Spin spin after drain When the laundries need only spinning after manual washing first drain then spin Twice wash Wash rinse spin O Twice wash wash rinse spin If the laundries are very dirty or the sleeve and collar are dirty first soak then wash Twice wash Wash rinse O spin O Quick wash wash
9. et hose please contact our after sale department immediately 2 Put the nut of the water inlet hose on the valve jointer go py 3 Fasten the nut Swing it gently to confirm if it s suitable Jointer Of the Water absorption cushion water inlet valve 1 Push down the slider Insert the water inlet ak hose into the jointer TAR h es 2 Hang the lock lever to the jointer Release the slider till a click sound is heard 1 Swing the hose gently to confirm if it is fastened stable 2 After installation open the faucet to check if it leaks 3 Do not bend the hose with overstrain 4 Each time before use please check if the connection between the jointer of the water inlet hose and the water faucet and the installation of the water inlet hose are firm so as to prevent i dropping from improper installation position Dismantle the water inlet hose 1 Close the water faucet 2 Press the locking lever Push down the slider Then pull off the water inlet hose If the machine is used more than once every week the jointer of the water inlet hose can be kept on the faucet to prevent damaging the fixing screw 1Preparation before washing Preparation before washing 1 Connect the water inlet hose Open Check if the laundries pocket Take has special the water faucet 2 Confirm that the washing machine is earthed reliably Then insert the power plug into the receptacle The earth terminal shall not link
10. g machine will fill water to the new water level 4 Press the Start Pause button Go all 5 Close the top lid 6 The washing is finished When the washing is finished the A s three indicators of Wash Rinse If you open the top lid the machine Spin are all on The power will be will stop working before spinning switched off automatically about 10 minutes after the finishing of the washing a 13 Disposal after washing After using please clean the lint and foreign materials of the lint filter etc in time Otherwise it may influence your using the machine Please first pull off the power plug from the receptacle before cleaning Clean the detergent box and set it on the control panel seat sia ee The lint filter must be used during washing It must be cleaned in time after each using Lint filter 1 Pull it up to dismantle 2 Push it down to install 3 Clean the filter screen after washing S Install Dismantle The filter screen of the water inlet valve is likely to be blocked by foreign materials and influence the water inlet Please clean it with brush every two months If the cabinet is dirty wipe it with wet cloth Do not flush it directly with water Wipe it with neutral detergent Do not wipe it with thinner petrol alcohol etc 1 After washing close the water faucet If needed you can dismantle the water inlet hose 2 Do not store water in the
11. inutes of water inlet the indicators of wash spin flash quickly The water faucet is not open e The water inlet valve is blocked The water pressure is too low and the current is too small Open the water faucet Push the Start Pause button Clean the water inlet valve Push the Start Pause button Wait for the normal water pressure before use No wash The machine does Is there power failure Is the power plug loose f water level reach the appoint level Use it when the power is on Insert the power plug tightly Affusion to appoint level not act No spin Is the power plug loose s the top lid is not closed Are the laundries put slantingly Insert the power plug tightly Close the top lid Re order the laundries Close the top lid There s abnormal sound inside the machine Is the machine slanting Are the laundries slanting in spinning Level the machine properly Re order the laundries The water faucet leaks Is the jointer screw of the water inlet hose is loose or twisted awry Common phenomena Phenomena e The spinning is intermittent when it starts Fasten the jointer screw properly Explanation e Balance the laundries to avoid slanting Push the Process selector button to select Spin but it doesn t work e The program is setting the drain time Some time is nee
12. ntle the protecting cover of the machine drain outletat the other side method 2 Put down the drain hose Take off the the same as the bushing Install the drainhose frame As indicated in Figure bushing as per indicated in Figure 4 1 put tne det hOse into he cabinet 4 Extend the drain hose from the other side Fix thedrain hose onto the base frame with the drain hoseframe As indicated in Figure 5 Then stretch onehand into the cabinet to nip the claw of the drain hose bush ing to remove the claw fromoriginal position Take off the drain hose bush ing with the other hand As indicated in Fig re Zand 3 Drain outlet protecting cove Drain hose frame Drain hose bushing Drain Hose bushing Figure 1 Figure 2 Figure 4 Figure 5 Cabinet 5 Install the protecting cover of the drain outlet at the other side as per indicated Inner Outer OuuE in Figure 6 Press Drain hose bushing Drain hose Take off bushing claw Press Figure 3 Figure 6 Usage of the drain hose Before using hang up the drain hose on suitable location Do not put down the drain hose on the ground AA Confirm the end of drain hose is higher than CA the level of tub If not the siphon will being 6 Install the water inlet hose Confirm the water faucet Water faucet suitable Water faucet not suitable gh _ It is required that the front end shall be longer than 10cm The outlet end surf
13. rinse spin When quickly wash the light dirty laundries Twice wash Wash rinse O_O spin O f you push the Process Selection button for 7 times it will resume the original mode and it will circulate like that f you select the Quick wash program you have to set the full procedure of wash rinse and spin The procedure cannot be selected 12 Total time including the normal water inlet time drain time excluding the power off time The total washing time may be influenced by the water inlet pressure and water level Spin time the time from intermittent running to finishing When selecting Twice wash program first soak for about 20 minutes pre wash for about 8 minutes then soak for about 5 minutes then do washing rinsing and spinning The wash time in the list includes the pre wash time 3 Adjust the water level knob to select suitable water level Three water levels available according to the laundries quantity High Medium Low After the water inlet as per the preset water level in case additional water quantity is required please first set the button to the Reset push and hold it to perform automatic water inlet When it reaches the suitable water level you can turn it to the needed water level After the water inlet under set water level if higher water level is needed please first turn the knob to Reset then turn back to needed water level The wash in
14. to gas pipeline and faucet water pipeline 3 Hang up the drain hose Clear the Tie the long strips fasten out the coins the buttons sand hairpins close zippers etc LA The quantity of the laundries shall not be too large Stretch and loosen the laundries before putting themin the tub 2 is running buttons of the laundries may cause noise For the sake of discretion please put the laundries with buttons into other laundries X Check if the laundries are applicable for washing with machine Divide the laundries that are not colorfast from other laundries Put those laundries difficult to absorb water into water with hand For those laundries with heavy soil please first remove the dirt like mud or dust For the parts with heavy soil please apply detergent on them in advance which can make it easier to remove the soil For those laundries that may get lint ball and those with long fur tum it over before putting in Do not put those laundries polluted by chemicals into the washing machine directly 2 Put in the laundries How to use the whitener Fill water to decided level Dilute the whitener with container Pour it slowly into the washing tub Avoid using whitener on laundries with color or pattern as they are prone to lose color The whitener shall not touch the laundries directly Refer to the user s manual for the usage and quantity of the whitener
15. washing S Please check if the water faucet is open and if the connection of the water inlet pipe is proper Itis suggested to use foamless washing powder Installation and adjustment Please install and adjust the machine according to the requirement of the manual It is very important to your security and correct operating the machine Install the bottom plate After you open the package please lean the washing machine gently down on soft items like the towel cloth blanket etc Install the bottom plate to the bottom of the machine with the eight screws by across screwdriver then lift the machine up gently See to the figure Bottom plate Screw Soft items The largest allowed slope of the base of the machine is 2 The slanting or rough ground will result in unstable running or stoppage of the machine Please adjust it with following methods Confirm it s horizontal Hang the lead line to confirm if it is horizontal Adjust the adjustable foot lt 2 1 To twist the adjustable foot please first lift up the side of the foot slightly loosen the adjustable nut and twist the foot 2 Fasten the nut after adjustment Install the lint filter After opening the package please take out the lint filter fromthe documentbag install itto the LEE inner tub See to the figure Install How to change the direction of the drain hose 1 Dismantle the back cover of the washing 3 Disma
16. washing machine for a long period Drain the water completely after each using 3 Be sure to pull off the power plug before maintenance 4 Hang up the power cord and drain hose 5 Wipe off the water drops on the surface of the machine and inside the tub Open the top lid for some time about 1 hour then close the top lid 14 Trouble shooting Answers to question If there s breakdown please pull off the power plug before checking The following phenomena are not breakdowns sometimes Please confirm again before sending it to repair If there are real breakdowns please come to the special maintenance department or after sale service department of our company Do not repair it by yourself Phenomenan In spinning the machine stops running The wash rinse spin indicator flash quickly The reason The top lid is not closed How to settle Close the top lid The draining does not work or the speed of draining is too slow the indicators of rinse spin flash s the drain hose blocked by foreign material Clean the foreign material Open and close the top lid once The safety switch acts The spinning can not work the indicators of wash rinse flash quickly e Are the laundries put slantingly Is the machine slanting Re order the laundries Close the top lid Level the machine in right position Open and close the top lid once The program pauses after about 15 m
Download Pdf Manuals
Related Search