Owners Manual - Best Converter
Contents
1. defective by the purchaser within the stipulated warranty period should be returned to the seller local distributor or directly to Garnet for evaluation and service Whenever direct factory evaluation service or replacement is necessary the customer must first by either letter or phone obtain a Returned Material Authorization RMA from Garnet Technologies directly No material may be returned to Garnet without an RMA number assigned to it or without proper factory authorization Any returns must be returned freight prepaid to Garnet Technologies Inc Suite 8 125 M amp M Ranch Road Granbury Texas 76049 Returned warranted items will be repaired or replaced at the discretion of Garnet Instruments Any Garnet items under the Garnet Warranty Policy that are deemed irreparable by Garnet Technologies will be replaced at no charge or a credit will be issued for that item subject to the customer s request If you do have a warranty claim or if the equipment needs to be serviced contact the installation dealer If you do need to contact Garnet we can be reached as follows Garnet Technologies Inc Suite 8 125 M8M Ranch Road Granbury Texas 76049 Email sales rvgauge com CHAPTER 8 SPECIFICATIONS Resolution 3 8 inch 10 mm Accuracy 8 or better limited by resolution and tank height and shape Temperature range 32 to 140 OF 0 to 600C Sender materials 0 008 thick glass epoxy circuit board with conformal coating for2. circuit protection Laminated on the back with 3M 300LSE Bonding Adhesive Sender length range 4 1 2 to 12 inches which will measure tank heights from 5 to 14 single sender and up to 26 dual senders Display mounting panel Black panel approximately 4 wide by 2 8 high by 1 thick 102mm wide X 71mm high X 25mm deep Panel screws to wall Power requirements Display requires 12 volts from the RV battery the system will function from 11 volts to 16 volts Current drain is less than 200mA Wiring A single two wire conductor required from the display to the senders All the senders are wired in parallel 12 V power and ground required for display Single wire required for LPG sender if sender grounded at tank LPG sender Display will work with an LPG sender resistance of 0 50 ohms to 0 500 ohms Display shows increasing level as resistance increases System must be calibrated with the LP tank full
3. doesn t the display is bad If an open circuit for all the senders is showing it is most likely a wiring open circuit or display failure since it is unlikely that all three senders are bad Try shorting the wiring together at the display the display should indicate a short circuit If it doesn t the display is bad If it does then remove that connection and short the wires together at the sender locations If no short circuit is shown then the wiring is open If the display does show a short circuit then the senders must be bad If a single sender is showing an open try shorting the wiring together right at that sender If a short now shows the sender is bad or not wired properly If no short circuit shows on the display the wiring to that sender is open To review the sender diagnostics 1 The sender diagnostics can be reviewed periodically to check for any degradation of the tank senders If a sender appears to be malfunctioning reviewing the diagnostics should be the first step in the troubleshooting process Note that there are no diagnostics for the battery voltage or LPG There are two diagnostics for the senders the signal power and the sender height The signal power is an indication of how much signal is being transmitted through the tank wall and picked up by the receive part of the sender If the signal power is too low it can indicate a sender which is detached from the tank excessive buildup on the inside of t
4. save wiring and to simplify installation the senders must be programmed so they know whether they are a single top or bottom sender This is done with the tab at the top center of the sender See the following diagram The senders default to single or bottom operation if the programming is not altered Consequently if the sender is for single or bottom operation nothing further needs to be done to it beyond programming it for the correct tank For a top sender remove the tab that says TOP next to it This is all that is required to program the senders for single top or bottom use However if you make an error you have one chance to correct it as described below If the TOP tab has been removed and it should be a single or bottom sender then cut out the recessed top correction tab that says TC next to it This reverses the effect of the top tab Verify that both the top and bottom senders have been programmed for the correct tank Cut for TOP sender Example of GREY TOP Example of BLACK SINGLE Cut for GREY tank Cut for BLACK tank sender programming or BOTTOM sender programming Example of corrected FRESH TOP Example of corrected GREY SINGLE Example of corrected FRESH SINGLE sender programming or BOTTOM sender programming or BOTTOM sender programming GRY or BLK cut by mistake BLK cut by mistake TOP cut by mistake Il lol al La IS ui Ee Eje ar sl A A i CHAPTER 6 TROUBL
5. the display will continuously recheck the voltage and show the updated value The reading may flicker back and forth between two values for example 12 6 and 12 7 volts This is normal behavior for a digital voltage display If another button is pressed before the 5 second time is up for the BATTERY button the display will immediately switch to showing the value for the new button The 5 second timeout is restarted every time a button is pressed There is no hold mode for the battery voltage CHAPTER 4 DISPLAY CALIBRATION To calibrate the LPG sender 1 The LPG tank must be full when the sender is calibrated otherwise the calibration will be invalid Fillthe LPG tank by using an alternate measurement method such as weight a spit valve or a mechanical gauge on the tank To calibrate press and hold down the LPG button the display will show some LPG level While continuing to hold down the LPG button press and hold down the BATT button Continue to hold down both buttons for about 5 seconds until the display shows LPG When this occurs release both buttons the display will show CAL for a second and then shut off completing the calibration procedure The LPG can be recalibrated as many times as desired although recalibration should not be needed unless the LPG tank sender or the display has been replaced To program the LED brightness 1 If the display is to be used inside the coach the LED brightness sh
6. which powers the display The voltage is shown with a resolution of 0 1 volt The display can use an existing LPG electrical sender to show the LPG level It can automatically calibrate to any sender and shows level on the LED display in percent of full from 0 to 100 CHAPTER 3 OPERATING INSTRUCTIONS The display is the only system component that is accessed by the user All user input to the display is done using the five buttons along the bottom of the display Operation of the display is as follows To read a water or sewer tank level k Press the button corresponding to the tank to be checked and release it the display will show the level in percent on the LED display If no other button is pressed then the display shut off after about 5 seconds If another button including BATT or LPG is pressed before the 5 second time is up for the first button the display will immediately switch to showing the new level or voltage The 5 second timeout is restarted every time a button is pressed To continuously display a reading press and release the desired button and then press the same button a second time When the button is released the display will be in hold mode which is indicated by the decimal point on the right hand side turning on While the display is in the hold mode it will recheck the level once per second so the user can watch the level change while the tank is being filled or drained The display will automaticall
7. wire and displays the level information in percent of full on a three digit LED display When the front panel button for a particular tank is pressed the display powers up and displays the level for that tank If the button is pressed and released the display will show the level for about 5 seconds and then shut down automatically If another button is pressed before the display shuts down then the new level will immediately be shown If the same button is pressed twice the display will hold on that tank and continue to show updated levels for 5 minutes before shutting off This allows the user to monitor the filling or draining of a tank By pressing two buttons at once the diagnostic functions can be accessed these are described in detail in the troubleshooting chapter If a sender is operating properly and connected to the display with good wiring then the display will show the level normally If the wiring is disconnected shorted or cut or if the sender panel is defective then the display will indicate an error code The various error codes are shown in the troubleshooting chapter With these diagnostic features and the digital nature of the tank level sensing technology it is almost impossible for the system to indicate an incorrect water level and in the very unlikely event it does occur the user can verify what is happening with the diagnostic information The system also shows the RV battery voltage by measuring the voltage
8. ESHOOTING GUIDE Display trouble codes If a sender or its wiring is not operating properly the following codes are shown on the display 1 If a sender is unresponsive or there is an open circuit in the wiring so that the sender is not connected the display will indicate an open circuit by showing OPn on the LED display If a sender is shorted or there is an short in the wiring the display will indicate an short circuit by showing Sht on the LED display If a sender is sending bad data there is damaged wiring or if there is electrical interference the display will indicate a data error by showing Err on the LED display Also if the senders have not been programmed correctly they can interfere with one another and result in Err on the LED display Check all the senders to make sure they are programmed correctly If they are replace the sender that is creating the error If the display has been programmed for a single sender and dual stacked senders have been connected the display will show StA In this case change the senders or reprogram the display as required If only a top sender has been connected the display will show nbo indicating that no bottom sender has been received If the tank should only have 1 sender correct the programming on the sender it should not be a top sender If the display has been programmed for dual stacked senders for tall tanks and only the bottom sender is w
9. Sa GARNET INSTRUMENTS LTD SEELEVEL II Tank Monitor Model 709 Owner s Manual IMPORTANT OPERATOR INFORMATION DATE INSTALLED SERIAL NUMBER Signal Level Sender Height Black Water Tank Grey Water Tank Fresh Water Tank PRINTED IN CANADA 1 2 3 4 5 6 7 8 GARNET INSTRUMENTS LTD SEELEVEL II Tank Monitor Model 709 Owner s Manual TABLE OF CONTENTS OVERVIEW SYSTEM DESCRIPTION OPERATING INSTRUCTIONS DISPLAY CALIBRATION SENDER PROGRAMMING TROUBLESHOOTING GUIDE SERVICE AND WARRANTY INFORMATION SPECIFICATIONS CHAPTER 1 OVERVIEW The SeeLeveL Il Tank Monitor represents a massive leap forward in level measurement technology for the Recreational Vehicle industry The SeeLeveL has a combination of features accuracy reliability and diagnostic capability that have never been available before The SeeLeveL Il will monitor the battery voltage the water and sewer holding tanks and the LP Gas tank The information is displayed on a 3 digit aloha numeric LED display In addition the system can display the operating characteristics of each of the tank sending units giving it unsurpassed diagnostic capability SEELEVEL II TANK MONITOR PUMP LEVEL IN PERCENT HEATER FRESH GREY BLACK GARNET INSTRUMENTS LTD MADE IN CANADA CHAPTER 2 SYSTEM DESCRIPTION The SeeLeveL consists of a display unit that mounts inside the RV and sender panels that st
10. he senders can be programmed for either the fresh grey or black tank This is done with the two tabs on the top corners of the sender See the following diagram The senders default to fresh tank operation if the programming is not altered Consequently if the sender is for the fresh tank nothing further needs to be done to it If the sender is for the grey tank remove the tab that says GRY next to it If the sender is for the black tank remove the tab that says BLK next to it This is all that is required to program the senders for the correct tank However if you make an error you have one chance to correct it as described below If the GRY tab has been removed and it should be a black tank sender or if the BLK tab has been removed and it should be a grey tank sender then cut out the recessed grey black correction tab that says GBC next to it This reverses the effect of the grey and black tabs If either the GRY or BLK tabs have been removed and it should be for a fresh tank then remove the other GRY or BLK tab When both the GRY and BLK tabs are removed it is equivalent to neither of them being removed If the sender is single no further programming is required If dual stacked senders are used the top sender must have additional programming as described below To program the sender as top or bottom 1 Since the senders are all connected in parallel to
11. he tank bad wiring to the sender low battery voltage or a defective sender The minimum signal power for proper operation is 5 The sender height is the number of receive segments present in the sender To determine the length of the sender multiply the calibration by 1 5 to get the length in inches The senders always auto calibrate to the length that they are cut so this diagnostic allows the user to confirm the length and to make sure that the auto calibration is working properly To check the diagnostics press and hold the button for the tank to be checked the display will show the level for that tank While continuing to hold down the button for the tank press the BATT button When the display shows dIA release the buttons the display will then change to showing the signal power diagnostic This is indicated by a P showing on the left digit for example P26 indicates a 26 signal power The signal power will show for 5 seconds The display will then change to showing the sender height This is indicated by a small h showing on the left digit for example h 6 indicates that the sender has 6 receive segments which is 9 inches high After 5 seconds of showing the height the display will shut off CHAPTER 7 SERVICE AND WARRANTY INFORMATION The warranty will apply only if the warranty card shipped with the equipment has been returned to Garnet Technologies Inc Garnet Technologies Inc warra
12. ick to the side of the holding tank A single two conductor wire is used to connect all the sender panels to the display The Sender Each sender panel is a flexible self adhesive printed circuit board which is stuck to the side of the holding tank The sender panel can be cut to length to match the height of the tank and it auto calibrates itself so that it can read from Empty to Full regardless of the height of the tank The sender scans the water level through the tank wall using patented digital techniques programmed into the sender microprocessor When the sender transmits the water level information to the display it sends a digital code that has built in error detection making it impossible for the display to read an incorrect level even if the wiring is bad In addition to the level the sender also transmits diagnostic information about its operation This information can be used to determine if there is buildup of sludge on the inside of the tank or to determine if the sender is delaminating from the side of the tank If sludge buildup in the tank becomes extreme the gauge will cease to operate the tank will always read empty so by monitoring the signal level the tank can be cleaned before the buildup gets excessive If the tank is more than 12 inches tall two senders can be stacked to allow measurement of levels up to 24 inches The Display The display receives the information from the three sender panels via a single two conductor
13. nts equipment manufactured by Garnet to be free from defects in material and workmanship under normal use and service for a period of one year from the date of sale from Garnet or an Authorized Dealer The warranty period will start from the date of purchase or installation as indicated on the warranty card Under these warranties Garnet shall be responsible only for actual loss or damage suffered and then only to the extent of Garnet s invoiced price of the product Garnet shall not be liable in any case for labor charges for indirect special or consequential damages Garnet shall not be liable in any case for the removal and or reinstallation of defective Garnet equipment These warranties shall not apply to any defects or other damages to any Garnet equipment that has been altered or tampered with by anyone other than Garnet factory representatives In all cases Garnet will warrant only Garnet products which are being used for applications acceptable to Garnet and within the technical specifications of the particular product In addition Garnet will warrant only those products which have been installed and maintained according to Garnet factory specifications LIMITATION ON WARRANTIES These warranties are the only warranties expressed or implied upon which products are sold by Garnet and Garnet makes no warranty of merchantability or fitness for any particular purpose in respect to the products sold Garnet products or parts thereof assumed to be
14. orking and the top one is not then the display will show ntP indicating that no top sender is being received If the top is working but no bottom sender is being received then the display will show nbo If neither sender is working then the display will show OPn Check the wiring and the programming of the senders If all is OK with that replace the bad sender For the LPG tank Opn indicates an open circuit in the wiring or a bad resistance sender in the LPG tank If there is a short in the wiring the display will read zero all the time The display contains a permanent memory which is used to store the programming for battery voltage calibration value the LPG calibration value and the tank sender signal levels These signal levels are used to help the system adapt to the tanks which increases sender accuracy at low tank levels If this memory should fail CAL will be flashed on the LED display indicating a calibration failure It will be necessary to replace the display if this occurs The diagnostics can be used to check the wiring and the senders If a short circuit is showing disconnect the senders one at a time at the sender location If the short circuit indication goes away when a sender is removed then that sender is bad If all the senders are removed but a short circuit still shows then the wiring may be shorted Disconnect the sender wire at the display the short indication should go away If it
15. ould be low If it is to be used in the service bay area where sunlight can reach it the LED brightness should be high To program the LED brightness the display needs to enter the brightness programming mode To do this press and hold down the BATT button the display will show the battery voltage While continuing to hold down the BATT button press and hold down the GREY button Continue to hold down both buttons for about 5 seconds until the display shows bri to indicate the brightness programming mode When this occurs release both buttons The display will now indicate the brightness that is currently programmed by showing b 1 b 2 b 3 or b 4 where b 1 is the minimum brightness and b 4 is the maximum brightness Press the GREY tank button to increase brightness or the FRESH tank button to decrease brightness When the display shows the correct brightness press the BATT button to exit the programming mode To program the number of senders for each tank 1 To program the number of senders for each tank the display needs to enter the sender programming mode This should only be done at the time of installation there is no reason to change the number of senders afterward Make sure that the number of senders programmed into the display matches with the number of senders connected otherwise the display will show an error To enter the sender programming mode press and hold down the bu
16. tton for the tank to be programmed the display may show a level or an error message for that tank While continuing to hold down the button for the tank press and hold down the BATT button The display will immediately show dlA diagnostics continue to hold down both buttons until the display enters the programming mode this should take about 5 seconds When the programming mode is entered the display will show FrS if doing the number of senders for the fresh tank GrS if doing the grey tank or bLS if doing the black tank When this occurs release both buttons The display will now show 1SE one sender or 2SE two senders based on what is currently programmed into the display These are the only two options the display will not work with more than two senders per tank To change the number of senders press the tank button each time the button is pressed the display will switch to the other number When the display shows the correct number of senders press the BATT button to exit the programming mode Each tank will need to be calibrated individually using this procedure The battery voltage is calibrated at the factory this should never need to be changed CHAPTER 5 SENDER PROGRAMMING To program the sender for the correct tank 1 Since the senders are all connected in parallel to save wiring and to simplify installation the senders must be programmed so they know which tank they are on T
17. y shut off after 5 minutes in hold mode To end the hold mode before the 5 minutes is up press any tank button and the display will shut off To read the LPG tank level 1 Press the LPG button and release it the display will show the level in percent on the LED display If no other button is pressed then the display shut off after about 5 seconds If the LPG button is pressed again a new reading will be obtained and displayed and the 5 second timer will be restarted If the button is held down the existing reading is held for as long as the button is pressed and the display will shut off 5 seconds after the button is released If another button is pressed before the 5 second time is up for the LPG button the display will immediately switch to showing the new level or voltage The 5 second timeout is restarted every time a button is pressed There is no hold mode for the LPG The LPG tank level cannot change fast enough to justify the use of the hold function except during filling of the tank The gauge should not be used as a full tank shutoff indicator since the LPG sender in the tank is not reliable or accurate enough to be used as a safe indicator of a full tank To read the battery voltage 1 2 Press the BATT button and release it the display will show the battery voltage on the LED display If no other button is pressed then the display will shut down after about 5 seconds If the BATTERY button is held down
Download Pdf Manuals
Related Search