GOSAFE - GPS trackers
Contents
1. Reply G787 V0 12 TZN 8 00 Time Zone 5 Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 1234 TZN 5 00 Reply TZN 5 00 5 12Immobilizzer Command Command format Explanations user password 4 digit command delimiter IMM Command Control Word Command delimiter M Command Parameter Values are M 0 Release Immobilizer M 1 Immobilize vehicle After receipt of this command the device will send back the IMM 0 or 1 After receiving the command device will act accordingly and immobilize or release immobilize of vehicle Note Once the device is disconnected from the OBDII port and it stays out of 5 10 Meter range the device relay will automatically immobilize the vehicle The device is equipped with internal backup battery which means it can supply the power for 5 10 Min to the device and the device can send back the alarm Power Off Once the device is completely power off the relay will immobilize the vehicle even the G787 stays inside the vehicle Gosafe provide especial 2 4Ghz RFID tags with the G787 If the vehicle needs to go for service and device need to remove from the OBDII port the 2 4Ghz tag must stay inside in order to start the Car 5 13Clear Alarm Command format eee UAC Explanations user password 4 digit command delimiter UAC Command Control Word After receipt of this command the device wi2. 1234 APN cmnet Reply G787 V0 12 APN cmnet 5 6 Enable Disable Over speed alarm Command format Explanations user password 4 digit command delimiter SPO Command Control Word command delimiter M Parameter 1 Enable 0 Disable After receipt of this command the device will reply with message SPO M device would enable disable over speed alarms If enable the device will send SMS to user mobile according to the setting of over speed limit If disable it will not detect the over speed limit Example Enable over speed alarm command is 1234 SPO 1 Disable over speed alarm command is 1234 SP0 0 Reply G787 VO0 12 SPO 1 Or G787 VO0 12 SPO 0 Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 5 7 Enable Disable Over Speed Alarm Parameter Command format ee sop AlertSpeed Alarm Speed Explanations user password 4 digit command delimiter SOP Command Control Word command delimiter Alert Speed set the speed in KM H 80 km h command delimiter Alarm Speed set the speed in KM H 100 km h After receipt of this command the device will reply with message SOP Alert speed alarm speed The Alert speed is the speed when the system start testing the over speed and send the alert first If the device crossed the alarm speed limit it will send the alarm Example Alert speed 80 Alarm speed 100 Co
3. 6 3 Error Command Alert Gosafe G787 V0 10 Error command 6 4 Password Modification Successful Confirmation Gosafe G787 V0 10 UPW 5678 6 5 User No Setting Successful Confirmation Gosafe G787 V0 10 UNO 8613912345678 6 6 Command Table The user command is shown in table7 The whole command format is PSW CMDXX Para Table 7 only show the second part CMDXX Para in the column of command format User Command List Ctrl Description Command Replay Word U UNOQ 139123 UNO 139 45678 12345678 020 bits default is empty Setting user or or set national number phone number GQJUNO Q UNO O set international number 86 is 861391234567 861391234 country number 5678 Setting user UPW 1234 UPW 1234 Four bits range 0000 9999 password 30M upload interval M can be 30 900S 15 59M 1 240H Default 30m G W Setting users to UUM 30M G T G upload mode it canbe upload mode O close uploading G upload GPS data by interval set when there is no GPS data uploading based on base station Gosafe Company limiled G78 User Marval pp eo Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Gosafe Company limiled G78 User Marval pp eo Dated 2011 05 23 i s osaf Gosafe Company Limited information S Always upload with LBS location L monitoring device call to the user by interval T data format it can
4. XXX country code YYYYYYYYYYYY center number After receipt of this command the device will reply with message SCN XXXYYYYYYYYY Example 1234 SCN 8613800200500 Replay G787 VO0 12 SCN 8613800200500 5 5 Set APN Command format tee APN CMNET internet internet Explanations user password 4 digit command delimiter APN Command Control Word command delimiter CMNET Access Point Name Confirm Access Point Name from the service provider command delimiter internet APN user name command delimiter Internet APN Password After receipt of this command the device will reply with message APN access point name APN user name APN password the device will connects with GPRS after receiving this command Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 Gasate Gosafe Company Limited The G787 is equipped with many APN Access Point Name from many countries If device automatically connects with GPRS then user no need to send above command If the device doesn t connect with GPRS then user may need to use APN command Example APN cmnet APN user name internet APN password internet command is 1234 APN cmnet internet internet Reply G787 V0 12 APN cmnet internet internet If you only set the APN without the username and password Example APN cmnet APN username empty APN password empty command is
5. G787 V0 12 Geo Fence Future use the current version firmware don t GPS 6 77 support it UTC 11 05 14 05 33 47 N23 164479 E113 428606 SPD Okm h 0 Alarm Geo Fence G787 VO0 12 Anti Jamming This alarm appear if the anti jamming feature GPS 6 77 is enable and the someone use GSM jammer near the device UTC 11 05 14 05 33 47 N23 164479 E113 428606 SPD Okm h 0 Alarm Anti Jamming Note The user can use the UAC command to clear user based alarm 5 16Default Parameters Device is set with the following default parameters When device power up first time the device will use the following parameters to connect and wait for user commands or server commands User upload mode 30M G W Manager phone number empty Manager upload mode 30M G T Server IP or domain name domain name empty IP 114 142 154 28 TCP port 3032 UDP port 3032 Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 Gasate Gosafe Company Limited TCP channel upload mode mode 0 60S G B UDP channel upload mode mode 0 60S G B Package number of per TCP upload Package number of per UDP upload percentage of data buffer per TPC upload 50 percentage of data buffer per UDP upload 50 Over speed 80 100 Enable disable over speed alarm Disable Enable disable vibration sensor Disable Enable disable phone roaming status test Enable Enable disable anti jamming Disable Time zone
6. O O O O O O O Environmental Storing Temperature 40 C to 85 C Conditions ae Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 Gasaf e Gosafe Company Limited 3 Features Real Time Location Mobile Map Location Latitude and Longitude Location GSM Base Station Location LBS Technology Convenient GSM Mobile Control Smart Stop Wireless Immobilizer Easy to use SMS Communication Mode Internal Movement Sensor for better power management Internal backup battery for Device disconnection notification Internal memory for the data buffer Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 Gasaf e Gosafe Company Limited 4 Quick Install Instructions 4 1 Configuration The G787 is supplied with USB cable Connect the USB cable to the device and connect it with the computer The computer may require USB driver It can automatically update the USB driver if not then please download the USB driver from http www gosafesystem com downloads asp and then click on the G787 USB driver After downloading the USB driver update the USB driver and establish the connection between G787 and your computer Use the configuration software to configure 4 2 Insert SIM card The user must arrange a SIM card with valid data plan Before inserting the SIM card it must be tested with your own mobile Insert the SIM c
7. Vibration sensor parameter 10 10 30 PUPPE ORO GPS Eimi http maps google com staticmap zoom 1 4 amp size 300x300 amp markers n e amp sensor t alse Supper link 1 LBS Link empty Phone list of SMS forwarding empty empty Time for talking SMS number counter 5 17Combine Command To save time and SMS resource on configuration user can apply combine command in which there is more than one command to operate configuration The combine command would begin with user password which is followed by commands commands order is flexible Format is as follow Command Command Password Parameter Parameter parameter word word First command Second Command If there is duplication of the same command in the same combine command just the last piece of command would be processed if there is error in the command the command with error would be discarded and device would only confirm setting of correct commands with no error warning If all the commands are error an alarm will be sent All setting commands except user No setting command under the condition of the user number Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 Gasafe has never been changed can be set by combine command Example 1234 UUM 30M G T UPW 1234 Gosafe Company Limited 6 Structures of SMS from Device 6 1 Normal Location SMS Format G Mode Located Successful Gosafe
8. be T text W super link User alarm UAC UAC UAC cleared Requests location information setting the SMS SCN 8613 800200500 APN APN user APN APN name user name 7 set APN APN password password APN APN APN APN center number Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 Usage send command to device the device will upload information Information format is the same as upload data by interval and this function can also be done by calling to the device and hang up after first ring Total is 20 bits 86 is national code must have Leave factory set empty Default usually no need to set SMS center number when user use SIM card device will record SMS center number automatically when change SIM card the old number will be delete and record new one Parameter range APN 1 30 characters user name 0730 characters password 0730 characters The second command way APN APN Means only set APN Device comes with of some APN list of some mobile service providers for some country when the APN information is included for the SIM card used no need to configure if APN is wrong GPRS connection will be wrong Monitor enable disable over Speed Speeding alarm parameters Motion sensor enable and disable Time zone setting Immobilizer Output Gosaf
9. G787 V0 10 Device Name and Version GPS 3 56 Satellites Connected amp Time used for Location secs LTM08 00 11 24 10 02 54 Specific time zone and Location time based on specific time zone N23 9 8329 Latitude in degree minute format E113 25 7149 Longitude in degree minute format Speed 1km h 39 Device speed and Move Direction TMP 25 6C Temperature PWR 12 5 Power Located Unsuccessful Gosafe G787 V0 10 MCC 460 MNC 1 LAC 517A CID 1FB1 TMP 25 6C PWR 12 5 6 2 Hyperlink SMS Format W Mode Located Successful Google link Gosafe G787 V0 10 http maps google com staticmap zoom 14 amp size 150x150 amp markers 39 9493 116 3875 amp sensor false TMP 25 6C PWR 12 5 Located Successful Yandex link Gosafe G787 V0 10 http m maps yandex ru ll 116 3875 39 949328 amp pt 116 3875 39 9493288 amp z 12 TMP 25 6C PWR 12 5 Located Unsuccessful Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 Device Name and Version Mobile Country Code Mobile Network Code Location Area Code Cell Identity Temperature Power Device Name and Version Google Map Link Temperature Power Device Name and Version Yandex Link Temperature Power Gasate Gosafe Company Limited Gosafe G787 V0 10 Device Name and Version MCC 460 Mobile Country Code MNC 1 Mobile Network Code LAC 517A Location Area Code CID 1FB1 Cell Identity TMP 25 6C Temperature PWR 12 5 Power
10. Gasaf e Gosafe Company Limited GOSAFE SYSTEM G787 Tracking Device User Manual Version 2 01 Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 Table of Contents Dig Device TAN Pee 4 1 1 PN hr 5 AER E EE EE EN 7 FEE Lee 8 Guck SN ENS I CONS EEE E 9 4 1 COTS UPATION EEE RE 9 4 2 FE MN 9 4 3 Me ANN ne ter teen rere rere rer A ce rete et 10 4 4 es 11 4 5 Installation of wireless relay cccsssccccseccceseeccesececeeeecuacceseucesseeeeeseceesuseesaeeeeseaeees 11 4 6 END serari E A E E cuneate E E TA T E T E ENORA 12 4 7 Mody PS 12 4 8 Set Work Mode e525 ces inccnciseierntcrdaispaantosaansencsessadenensenes i100 ER E 12 5 Commands for Device Setting ccccccssccccesecccesscccesscceeecccceecceseucesseneecsuecessaecessaueeseaeeesaaess 13 5 1 UNN 13 5 2 Modify User PaSSWOMKd c sscccccssccccescccesseccsecccenscesauccessucesseusessuesessaecessaecesaaeeesaaees 13 5 3 Set Upload Mode interval and type cccccssecccssseccesececeecceseuceeseeeeeseceseeaeeesaeeesees 14 5 4 Set Message Center NUMDEL ccccsecccsssecceececsesccseeeceseuececsusceseaeeessaeessaueeeseesesees 15 5 5 NL NN 15 5 6 Enable Disable Over speed alarm rrrnrrnrnnnrnnnrrnnnnnnnnnnrvnnnnnnnnnnnnnnenensrnnrnnnnnnsnenenennene 16 5 7 Enable Disable Over Speed Alarm Parameter rrrrrrrrnnnnnnnnnnnnnrnnrrnnnnvnnnnnnnenersrnnnnnnnn 17 5 8 Enable Disable SMS w
11. M has GPRS function or not TCP connection Error 7 flashes To check if the server is normal Unknown Error 8 flashes Power OFF then Power ON if there is still the error please contacts us Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 8 Appendix 8 1 Characters for Commands Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23
12. YXXXXXXXXXX The user can listen inside the vehicle but the driver will never know this activity Example 1234 VOM 86123456789 Reply G787 VO0 12 VOM 123456789 5 10Location Poll There are two ways to poll the location from the device 1 By sending PQR SMS to device user password 4 digit command delimiter PRQ Command Control Word Example 1234 PRQ Reply G787 VO 17 PRQ The device will send back the location information after getting the latest GPS data G787 VO 17 Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 GPS 5 67 UTC 11 05 11 06 47 N23 164367 E113 428548 SPD 0km h TMP 37 8C PWR 10 5V 2 The user mobile can call to the device number and hangup after first ring The device will send back the GPS location to the user mobile G787 VO 17 GPS 5 67 UTC 11 05 11 06 47 N23 164367 E113 428548 SPD Okm h TMP 37 8C PWR 10 5V 5 11Set Time Zone Command format ve ran Ji Timezone Explanations user password 4 digit command delimiter TZN Command Control Word command delimiter Time Zone Enter the time zone parameters 12 00 to 12 00 After receipt of this command the device will send back TZN Time zone After receiving this command the device will send the local time in the SMS if the gps data is valid If there is not GPS data device will not send the time Example Time zone 8 1234 TZN 8 00
13. ard in your own mobile and try to send out SMS and receive SMS if it works fine then try to connect to internet by opening any website in mobile browser Now you can remove the black cover from the G787 SIM card jack hole Remove the black cover After removing the black cover you can insert the SIM card in the jack Please note the following pictures for the direction of the SIM card SIM Direction Press the SIM card inside the SIM card jack completely Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 Note Please do activate the SIM card disable its PIN code function and make sure SIM card has enough balance before operating the device Each time before taking SIM card out of or inserting SIM card into the device device power supply remove the device from the OBDII connector or it would damage device and or your SIM card 4 3 Locating OBDII Port Normally ODBII port is available in all the vehicles manufactured after the 1996 and 2000 This port is located under the dash near the driving side of the vehicle Normally this port is covered with some cover Some common images of OBDII port location Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 Gosafe Company Limited 4 4 Connecting G787 Remove the cover on the OBDII port and connect the G787 to the same port as shown in blow pic
14. de YYXXXXXXXXXX telephone No with country code is country code mark while yy is country code You can send SMS command to set or modify user No through any mobile phone number No matter the telephone No in command with or without country code it is acceptable Device will reply a message for confirmation on after receipt of setting command to the set mobile phone from which the setting command was sent Example Setting command without country code in telephone No 1234 UNO 13912345678 Setting command with country code in telephone No 1234 UNO 8613912345678 Reply G787 V0 12 UNO 13912345678 Or G787 V0 12 UNO 8613912345678 5 2 Modify User Password Command Format mee UPW 000 Explanations User old password 4 digit Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 command delimiter UPW Command Control Word command delimiter XXXX user new password 4 digit Only if this command is sent by user No the system can process this command After password modification successful please do memorize your new password Example 1234 UPW 5678 Reply G787 V0 12 UPW 5678 5 3 Set Upload Mode interval and type Command Format uum os G Explanations user password 4 digit command delimiter UUM Command Control Word command delimiter xx SMS interval S com
15. device Only if this command is sent by user No the system can process this command 4 8 Set Work Mode There are 4 different work modes configurable for device according to user s need O S G and L Detailed information on 4 work modes please go to Commands for Device Setting in this User Manual Example To set device in G Work Mode you should send the following SMS command to the SIM card No UUM 3O0M G T Explanation password UUM Command Control Word G the Work Mode user wants to configure T the type of message Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 5 Commands for Device Setting All the commands for device setting in this User Manuel are in the same format user password command content The command content is restricted to digits 0 9 English characters a z and or A Z and or common punctuations Please check Characters for Commands table in Appendix beyond which device cannot recognize If there is any character device cannot recognize device will ignore it and will not give any related warning to user All English control words in command could be capital words or lower case words 5 1 Set User No Command Format es uno anno Explanations user password 4 digit command delimiter UNO command control word command delimiter XXXXXXXXXX telephone No without country co
16. e Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 VOM 13912345 678 Or VOM 8613912 345678 TZN 8 OO VOM 1391 2345678 Or VOM 861 391234567 TZN 8 00 Gosafe Company Limited 86 is country code The number can t be empty Usage send command the device will call back open microphone user start monitor 0 close 1 open Default SPO 1 100 prompt 120 alarm Default SPO 80 100 0 Close shielding sensor related function IS cancelled relevant information don t send 1 open can Use related functions of movement sensor Set local time zone parameter from 12 00 to 12 00 Negative represent western time zone positive represent east eastern time zone Default 0 00 o close 1 open device send power cut command or the device is disconnection cut power of vehicle Gasate Gosafe Company Limited 7 LED Flashes amp Relevant Device Status There is an external LED light to reflect device status in G787 In order to check device status through this LED light flashes LED is located right next to the USB port When device is at work LED will flash at 8 sec cycle constantly to show related GSM and GPS status in each cycle In each flash cycle when device is at work LED will flash to indicate GSM status first then GPS status there is an interval between them To check the statuses please count the LED light flashe
17. hen movement trigger rrrrrrrrnnrrrnnnnnnnrrrrrrrrnrrrnnnnnnnnnsrrrnnnnnnne 17 5 9 Set Voice Monitoring Number rrrrnnrrnnnnnrnnnnnnnnnnnrnnnnsrnnnnsnnnnnennnnnrnnnnesrnnnnnsnnnssennnnesnnn 18 5 NNN 18 S GERMO ZONO cra A NE 19 512 Immobilzer Command sersan a A E EE T 20 SE NNN 20 5 14 Commands Wait h ssseossssnssrrvsnneserssvsvnsesevnnnsresesneneneennnnseseessnsnnenesnnnnserssvenesenensanseenennene 21 ANN 21 EG PENNEN 22 S17 PO 23 6 Structures of SMS from Device rrannnnnnnnrnnnnnrnnnnrnnnnnrnnnnnrnnnnnrnnnnnrnnnnsrnnnnennnnnennnnssrnnnnsennnssennnne 24 6 1 Normal Location SMS Format G Mode ccccccsssceceesceeeseceeencceesseeeeseceeeeeeeeeecens 24 6 2 Hyperlink SMS Format W Mode rrrrrarnrrnrnnnrrrnnnnnrrnnnnnnrrnnnnnernnnnnerrnnnnnnsrnnnnsssnnnnene 24 6 3 Error Command Me x sesncotcncciscecacteylinewtonanwsssatade adeususierncenesncswoncadssetneleslnteduasertencaies 25 6 4 Password Modification Successful Confirmation cccccssscccssececseseeeeeseeseseesaeees 25 6 5 User No Setting Successful COnfirmatiOn ccccccscccsssccceeccceeeeeseceseeeeeseeeeessaeeess 25 6 6 GoW al 0 AE DE EE EEE one esses EEE 25 7 LED Flashes amp Relevant Device Status rrrrrnnnnnnnnnnrnnnnnrnnnnnnnnnnernnnnnrnnnnsnnnnernnnnnernnnennnnssnnnneee 28 PTO D NE EE EEE EE 30 8 1 Characters for COMMANAS cccsssecccesscceeeccesececseececsaneesaueecssecessuecessuseessassesaneeeas 30 Gosafe Company Limi
18. ll send back UAC It will clear the user alarm and device will not send the user alarm Example 1234 UAC Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 Reply G787 V0 12 UAC 5 14Commands Wait In the event of there come commands from user when device is in sleep and couldn t process commands at each wakeup device will wait one minute to receive those commands and take precedence to process them then response one confirmation message after 1 min device would receive and process real time commands then reply accordingly 5 15Alarms The device sends alarm immediately it triggers The message receive when device is in alarm as follows G787 V0 12 GPS 6 77 UTC 11 05 14 05 33 47 N23 164479 E113 428606 SPD 0km h 0 Alarm Power Off List of Alarms G787 V0 12 Power Off GPS 6 77 UTC 11 05 14 05 33 47 N23 164479 E113 428606 SPD 0km h 0 Alarm Power Off G787 V0 12 Over Speed GPS 6 77 UTC 11 05 14 05 33 47 N23 164479 E113 428606 SPD Okm h 0 Alarm Over Speed G787 V0 12 Moving When the vehicle I stopped and the movement Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 Gosafe Company Limited GPS 6 77 sensor is enable the device sends move alarm on the trigger UTC 11 05 14 05 33 47 of movement sensor N23 164479 E113 428606 SPD 0km h 0 Alarm Moving
19. mand control word interval in Second Minute Hours command delimiter G Command Control Word Mode command delimiter T Type of upload Text with hyperlink After receipt of this command device will reply you a piece of message in UUM 30M G T SMS Format At each wakeup device would send you a location report message in this format If device is in positive real time work mode upload operating cycle OOS or OOM or OOH only one piece of location report message will be sent by device if updated location report is in demand thereafter please send another command then device will response accordingly Operating Cycle xxxS Seconds upload range 30 900 seconds xxxM Minute upload range 15 59 minutes xxxH Hour upload range 1 240 hours Work Modes O Cancel Upload G GPS based location S Always update with GSM base station LBS L Device calls back after set interval of time for voice monitoring Message Types Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 T Text format SMS W Text format with hyperlink SMS with hyperlink Example 1234 UUM 30S G T Reply G787 V0 12 UUM 30S G T 5 4 Set Message Center Number Command format cee SON 5 XXKYYYYYYYYYYYYY Explanations user password 4 digit command delimiter SCN Command Control Word command delimiter XXXYYYYYYYYYYY Message center number
20. mmand 1234 50P 80 100 Reply G787 V0 12 SOP 80 100 5 8 Enable Disable SMS when movement trigger Command format ee mor i M Explanations user password 4 digit command delimiter MOT Command Control Word command delimiter M Parameter 1 Enable 0 Disable After receipt of this command the device will reply with message MOT M device would enable disable the SMS to user mobile when movement is sensed by movement sensor Note The device will automatically send location SMS to the user once it will sense any movement The device will send only one SMS at the start of the movement Device will wait for the vehicle to stop and will start the counter to 60 min If the movement is after 60 min device will again send the SMS to the user mobile Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 Example Enable SMS upload when movement trigger command is 1234 MOT 1 Disable SMS upload when movement trigger command is 1234 MOT O 5 9 Set Voice Monitoring Number Command format vom YYXO000000000 Explanations user password 4 digit command delimiter VOM Command Control Word command delimiter YYXXXXXXXXXX telephone No with country code is country code mark while YY is country code After receipt of this command the device will call back to the number mentioned in the command Y
21. rd in the G787 and connect he device to the OBDII port in the vehicle The system have internal movement sensor which controls the power management of the device G787 is equipped with highest available GPS uBlox modules and able to use A GPS Assist GPS technology to give help connecting the device with GPS faster with more accuracy Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 basate Gosafe Company Limited 1 1 Physical Appearance Device OBDII Plug to G connect with Vehicle Front View n pg J Tag Interface Rear View USB Port SIM Card Jacket GPS GSM LED Wireless Module LED MIC Wireless Relay Complete Set with USB Cable Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 Gasate Gosafe Company Limited Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 Gasate Gosafe Company Limited 2 Specification IP Rating IP62 amenna mem Quad band 850 900 1800 1900MHz Class 10 4 downlink 2 uplink max 5 Mobile Station Class B AT amp T R amp TTE CE GCF FCC PTCRB Approvals Anatel IC China SRRC etc Smed 1308Mm o O LBS Location Accuracy antenna internal Cold Starts 27s Acquisition Aided Starts lt 1s sein Hot Starts lt 1s Location Accuracy Sensor 3D G Force Sensor Onboard O
22. s then compare it to the chart below status MRD Flashes GSM module on and registered 4 flash then TCP connection GPS module ON but haven t located 1 flash after interval behind GSM status flash in ed Conaae ee GPS module ON and located 2 flashes after interval behind GSM status flash in C eamaae GPS module OFF No flash after interval behind GSM status flash in Device also uses LED flashes to indicate relevant error if any of the following situations happens Device Error SIM card no balance GSM network cannot register When there is any error above LED light will ON 1sec then flash quickly which helps trouble shoot errors user can count LED quick flashes then compare it to below chart GSM module Communication Error 1 flash Power OFF then check GSM module power supply and communication SIM card Error 2 flashes Power OFF then check whether SIM installation is good and PIN is disabled Cannot register at GSM network 3 flashes To check whether SIM card is overdue and or device in an area there is no GSM signal GPS module Error 4 flashes Power OFF then check GPS module os _ peeereeenmengage SMS Sending Error 5 flashes To check whether there is SIM card meet JP tn oor ae Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 Gasate Gosafe Company Limited Coo y smeardisoverde Can t use GPRS 6 flashes To check whether the APN is correct and SI
23. ted G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 Gasate Gosafe Company Limited Version specification This document was made based on the G787 products after this version was fixed If there is any need to change such as increased command or modify command etc must be agreed by scriptures control center After Revised the version will need upgrade Version Modification Basic Hardware Version Version 2011 04 27 V1 01 V1 01 V1 01 1 Upload mode add to S mode UUM SSM TPM UPM command Server port default 3032 SIP command Server address domain default empty SDM command Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 1 Device Introduction G787 which uses GSM SMS together with GPS to locate your belongings is a new model tracking device designed by Gosafe Company Limited Connect amp Go concept G787 can connect with OBDII diagnostic port and can get necessary power from the same port Inside G787 there are GSM modem GPS receiver control PCBA microprocessor power circuit and so on Before starting G787 installation please one SIM card which works based on GSM network that is offered by GSM mobile operating agency and can work with GPRS G787 is easy to install device even nonprofessionals can install this device You only need to get the valid data SIM Card Insert the SIM ca
24. ture 4 5 Installation of wireless relay The units contain one wireless relay This relay can be installed using the relay socket in the same way as other relays installed for the immobilization The only thing which needs to be careful when installing the relay is the direction of the relay The relay must be installed same as the following picture This part must be face upside when installing the relay Gosafe Company Limited G787 User Manual Version 2 01 Prepared By Mr Chen Approved by Mr Yang Dated 2011 05 23 4 6 Set User No To set user No you can use any mobile phone to send the following SMS command to the SIM card No 1234 UNO 8613912345678 or 1234 UNO 13912345678 Explanations 8613912345678 user No with country code 13912345678 user No without country code UNO Command Control Word After receipt of the above SMS command device will reply a confirmation SMS and work at default work mode 30M G W To protect device if there is any error in this command device will not send back any error warning 4 7 Modify Password To modify factory password at the first usage is strongly suggested Password should be 4 digits that picked from 0 9 To modify password you can use user No send the following SMS command to the SIM card No 1234 UPW 5678 Explanations 1234 Factory Password 5678 New Password Note Please memorize your New Password and wait for confirmation SMS for password modification from
Download Pdf Manuals
Related Search